So I recently updated to Android 6.0 and it worked perfectly. So about 1 month later (today) I get prompted with a message stating there is an update going to install in30 sec. I let it do its thing setting the phone to comeback right when it's booting up(or so I thought) instead it's the boot loop going on over and over. So I remeber the flash tool so I decided to go with that but it didnt work. Is there any fix for the Android 6.0 boot loop on LG g3 d850?
Unveiled Skill said:
So I recently updated to Android 6.0 and it worked perfectly. So about 1 month later (today) I get prompted with a message stating there is an update going to install in30 sec. I let it do its thing setting the phone to comeback right when it's booting up(or so I thought) instead it's the boot loop going on over and over. So I remeber the flash tool so I decided to go with that but it didnt work. Is there any fix for the Android 6.0 boot loop on LG g3 d850?
Click to expand...
Click to collapse
You have to use LGUP since you were on MM.
Sent from my iPhone using Tapatalk
hyelton said:
You have to use LGUP since you were on MM.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Is there any known fix cause I kinda need my phone? It just sucks how carriers treat people who don't buy the newest version of a phone.
hyelton said:
You have to use LGUP since you were on MM.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Didn't work says device unknown
hyelton said:
You have to use LGUP since you were on MM.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
LGUP is only for the D855 Model of the lg g3 I have D850.
Unveiled Skill said:
LGUP is only for the D855 Model of the lg g3 I have D850.
Click to expand...
Click to collapse
LGUP works will ALL models.. And if your running MM LGUP is the only software that's going to work for you
Sent from my iPhone using Tapatalk
hyelton said:
LGUP works will ALL models.. And if your running MM LGUP is the only software that's going to work for you
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Am I doing something wrong then because I keep getting device unknown. I already set com ports to 41 and ran as admin.Is there something I missed.
Unveiled Skill said:
Am I doing something wrong then because I keep getting device unknown. I already set com ports to 41 and ran as admin.Is there something I missed.
Click to expand...
Click to collapse
Your running stock rom right? If your currently running a custom rom you need to first flash a stock based rom based on D850.
Sent from my iPhone using Tapatalk
hyelton said:
Your running stock rom right? If your currently running a custom rom you need to first flash a stock based rom based on D850.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Is there a tutorial of how to flash to a stock Rom?
Unveiled Skill said:
Is there a tutorial of how to flash to a stock Rom?
Click to expand...
Click to collapse
Yes my LG G3 back to stock guide.
hyelton said:
Yes my LG G3 back to stock guide.
Click to expand...
Click to collapse
Link Please. Thank you
Unveiled Skill said:
Is there a tutorial of how to flash to a stock Rom?
Click to expand...
Click to collapse
Unveiled Skill said:
Link Please. Thank you
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2785089
hyelton said:
http://forum.xda-developers.com/showthread.php?t=2785089
Click to expand...
Click to collapse
There are no kdz for at&t. And the 2015 method dosent work as it was the flash tool I tried it says DOWNLOAD FAILED every time I start it up.
Unveiled Skill said:
There are no kdz for at&t. And the 2015 method dosent work as it was the flash tool I tried it says DOWNLOAD FAILED every time I start it up.
Click to expand...
Click to collapse
There is no kdz for AT&T models and never will be. What do you mean by download failed? Need to explain more. Were you running MM? If so that's why as you must use LGUP...
Also make sure your placing the phone in download mode and using a USB 2.0 port. USB 3.0 will not work
Sent from my iPhone using Tapatalk
hyelton said:
There is no kdz for AT&T models and never will be. What do you mean by download failed? Need to explain more. Were you running MM? If so that's why as you must use LGUP...
Also make sure your placing the phone in download mode and using a USB 2.0 port. USB 3.0 will not work
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
When i start the flash in the 2015 method it says DOWNLOAD FAILED in red at the top. So you said if I'm running MM LGUP should work but my phone appears in the unknown and it is in download mode.
Unveiled Skill said:
When i start the flash in the 2015 method it says DOWNLOAD FAILED in red at the top. So you said if I'm running MM LGUP should work but my phone appears in the unknown and it is in download mode.
Click to expand...
Click to collapse
With LGUP have your phone turned on with USB debugging mode enabled.
Sent from my iPhone using Tapatalk
hyelton said:
With LGUP have your phone turned on with USB debugging mode enabled.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
That the problem I have the boot loop after a failed updated so I can't turn the phone on to change settings.
hyelton said:
With LGUP have your phone turned on with USB debugging mode enabled.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Do you think a command sent to the device while it's in download mode could enable usb debugging.
Unveiled Skill said:
Do you think a command sent to the device while it's in download mode could enable usb debugging.
Click to expand...
Click to collapse
USB debugging is for software that's not required in download mode and doesn't have anything to do with download mode. What was you running before? As custom roms will make it show up unknown. And not sure on a fix for that
Sent from my iPhone using Tapatalk
hyelton said:
USB debugging is for software that's not required in download mode and doesn't have anything to do with download mode. What was you running before? As custom roms will make it show up unknown. And not sure on a fix for that
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
I Was running lollipop rooted flashed to stock updated to MM then tried to install an OTA update and Boot loop started after
Related
What are my options for a failed root attempt on my flex 2? I've tried recovery and that doesn't work. Can't find any ROM's. Am I stuck with a bricked device until the ROM's are out?
Lurtz988 said:
What are my options for a failed root attempt on my flex 2? Can't find any ROM's. Am I stuck with a bricked device until the ROM's are out?
Click to expand...
Click to collapse
What do you mean by "I've tried recovery and that doesn't work."? You can't get to recovery? You can't restore?
lge h959 v10c rom(kdz format) works, u can try that rom with lg flash tool. Flash it in downloading mode.
Stank0 said:
What do you mean by "I've tried recovery and that doesn't work."? You can't get to recovery? You can't restore?
Click to expand...
Click to collapse
I tried going to the recovery menu via hardware reset and when I hit "restore factory settings" it did it's thing but still freezes at login screen.
Ive got the same problem with my sons flex 2. He decided to try to root it and now all it does is sit at the boot screen. Is there anything that can be done or should i send it back for repair and play dumb?
Thanks
cjm1979 said:
Ive got the same problem with my sons flex 2. He decided to try to root it and now all it does is sit at the boot screen. Is there anything that can be done or should i send it back for repair and play dumb?
Thanks
Click to expand...
Click to collapse
How far in the rooting process did you make it? Wondering which part could have daused the issue. I have rooted and unrooted probaby 10 times with not the slightest issue.
Sent from my GT-N8013 using XDA Free mobile app
shuka325 said:
How far in the rooting process did you make it? Wondering which part could have daused the issue. I have rooted and unrooted probaby 10 times with not the slightest issue.
Sent from my GT-N8013 using XDA Free mobile app
Click to expand...
Click to collapse
Not sure as I didn't do it. My son says he thought it had done all of it but then stuck when it came to boot screen. Is there a stock Vodafone UK image anywhere? Had a look and couldn't see any
Cheers
Sent from my HTC One M8 using Tapatalk
cjm1979 said:
Not sure as I didn't do it. My son says he thought it had done all of it but then stuck when it came to boot screen. Is there a stock Vodafone UK image anywhere? Had a look and couldn't see any
Cheers
Sent from my HTC One M8 using Tapatalk
Click to expand...
Click to collapse
Use LG mobile support tool. Launch it and select upgrade recovery. Then type in IMEI and follow instructions.( hold volume up and connect usb cable to boot in to download mode)
http://www.lg.com/uk/support-mobile/lg-H955#software
Lg g flex 2 us995 us cellular stuck at boot
LG G FLEX 2 US995 US CELLULAR STUCK AT BOOT
i tried to unroot my lg g flex 2 us995 with SIMPLY UNROOT.APk. it was successful. but when i reboot my device it got stuck in boot at lg logo. its going to download mode. but not booting up. neither going to recovery,
any help from worthy developers
zydroid1985 said:
lge h959 v10c rom(kdz format) works, u can try that rom with lg flash tool. Flash it in downloading mode.
Click to expand...
Click to collapse
hello bro. i saw your comment oon lg flex 2 brick. i have lg flex 2 us995 cdma. i brick it while unrooting it with SIMPLY UNROoT.APK. i cant find any kdz file for this modal over internet. do u have any idea what should i do. should i flash other modal stock like 955? is that safe for my modal
shuka325 said:
How far in the rooting process did you make it? Wondering which part could have daused the issue. I have rooted and unrooted probaby 10 times with not the slightest issue.
Sent from my GT-N8013 using XDA Free mobile app
Click to expand...
Click to collapse
how did you unroot your flex 2. I root it successfully but after unrooting it with simply unroot.apk i rebbot it and then was stuck on lg logo. I have us995 modal 10c rom on it. How can i get rid of this issue
muzammil457 said:
how did you unroot your flex 2. I root it successfully but after unrooting it with simply unroot.apk i rebbot it and then was stuck on lg logo. I have us995 modal 10c rom on it. How can i get rid of this issue
Click to expand...
Click to collapse
Within settings of SuperSU, closer to the bottom, there is option to unroot.
Sent from my LGLS996 using XDA Free mobile app
shuka325 said:
Within settings of SuperSU, closer to the bottom, there is option to unroot.
Sent from my LGLS996 using XDA Free mobile app
Click to expand...
Click to collapse
Thts cool bri. But too late for me. I bricked my device. And unluckily no firmware file on internet. Waiting for some body to upload.
shuka325 said:
Within settings of SuperSU, closer to the bottom, there is option to unroot.
Sent from my LGLS996 using XDA Free mobile app
Click to expand...
Click to collapse
Is that safe to flash Ls996 tot on us995 modal. Wont it hard brick my phone???
fail flash
hi
i have a 955 g flex2 and i wrong 969 kdz file flashed stoped at 99% and sadly turned the phone off ,now i cant turn on the phone help
Im pretty new to this site so i appologize if im posting in the wrong area. I got a new h950 flex 2 and i rooted and installed a app. that fixes permissions, fixed the phone turned off and bricked. Coouldnt find a way to unbrick so i flashed a h955 kdz. Which now the phone works. But no cell service....it says im on airplane mode...and sometimes it says cell radio off...so i was wondering if there is something i could change in build prop or flash a radio i just cant seem to find a kdz for att ho50....i see the chinese are the only ones that have a puerto rico edition....no offense to them just cannot pernounce the website. If someone can ease help i dont care which version it is i just want cell serive
Hey, what's your status? Have tou manages to solve the issue?
Sent from my LG-D855 using Tapatalk
anyone have a bricked flex 2 they'd like to donate for testing?
looking for flex 2 devices with messed up bootloader.. either showing up as a 9008 qhsusb bulk device or phone not turning on at all (nothing shows on screen).
i do have one black screen and 9008
Qdloader 9008
I have mine too, i followed some genius and ended up with dead phone, awaiting solution as it was rolled for G3 and other LG devices. :crying:
My phone got soft bricked while i was flashing the rom on my g3. Now whenever i try to flash the stock Firmware through .tot method it goes till 94%. It says "Fail to Get mini OS Status"
It's download mode is working. But when i start the device it goes on to show me LG logo again and again.....
Plz Help me what should i do....
Rafaaaay said:
My phone got soft bricked while i was flashing the rom on my g3. Now whenever i try to flash the stock Firmware through .tot method it goes till 94%. It says "Fail to Get mini OS Status"
It's download mode is working. But when i start the device it goes on to show me LG logo again and again.....
Plz Help me what should i do....
Click to expand...
Click to collapse
What rom was your trying to flash that caused that problem? And did you try choose board_dl in the tot/dll selection screen and flash that way?
hyelton said:
What rom was your trying to flash that caused that problem? And did you try choose board_dl in the tot/dll selection screen and flash that way?
Click to expand...
Click to collapse
I tried to flash the "LGD850AT-01-V10d-310-410-JUN-19-2014"
No I just selected Upgrade_dl.....
Rafaaaay said:
I tried to flash the "LGD850AT-01-V10d-310-410-JUN-19-2014"
No I just selected Upgrade_dl.....
Click to expand...
Click to collapse
Choose board_dl and let me know what happens
hyelton said:
Choose board_dl and let me know what happens
Click to expand...
Click to collapse
It went till 89% Then it said that port open error.
Secondly the Enable XML log should be selected or not?
Rafaaaay said:
It went till 89% Then it said that port open error.
Secondly the Enable XML log should be selected or not?
Click to expand...
Click to collapse
Now remember failing after 80% is normal. Did it boot? Anything after 80% is just rebooting and not part of the flash.
Were you running MM 6.0 before ? If so you'll need to use LGUP
hyelton said:
Now remember failing after 80% is normal. Did it boot? Anything after 80% is just rebooting and not part of the flash.
Were you running MM 6.0 before ? If so you'll need to use LGUP
Click to expand...
Click to collapse
Yes it booted 4-5 times at 89%.
It got bricked when i tried to Install MM 6.0 and now it is in the middle of nowhere.
How can i use LGUP.
Rafaaaay said:
Yes it booted 4-5 times at 89%.
It got bricked when i tried to Install MM 6.0 and now it is in the middle of nowhere.
How can i use LGUP.
Click to expand...
Click to collapse
Just google LGUP . What Mm 6.0 rom did you try to install? There's no 6.0 official for D850
hyelton said:
Just google LGUP . What Mm 6.0 rom did you try to install? There's no 6.0 official for D850
Click to expand...
Click to collapse
I Could not find KDZ Version of G3 D850 Either of stock or lollipop.
Rafaaaay said:
I Could not find KDZ Version of G3 D850 Either of stock or lollipop.
Click to expand...
Click to collapse
That's because there's not. You use a tot file with the tot method or LGUP
hyelton said:
That's because there's not. You use a tot file with the tot method or LGUP
Click to expand...
Click to collapse
On LGUP It is saying Unkown(Model) . Then shows an error sayin u have to chose a known model.
Rafaaaay said:
On LGUP It is saying Unkown(Model) . Then shows an error sayin u have to chose a known model.
Click to expand...
Click to collapse
Download LGUP from my LG G3 back to stock thread. You may had downloaded an old version.
hyelton said:
Download LGUP from my LG G3 back to stock thread. You may had downloaded an old version.
Click to expand...
Click to collapse
Same problem.... I Got it from ur Go Back to Stock But it says that Model Unknown.
I connected the device in download mode. It is showing "910K B3 QEM"
Rafaaaay said:
Same problem.... I Got it from ur Go Back to Stock But it says that Model Unknown.
I connected the device in download mode. It is showing "910K B3 QEM"
Click to expand...
Click to collapse
If it shows that you have a hard brick
hyelton said:
If it shows that you have a hard brick
Click to expand...
Click to collapse
Now What....
But it is starting into download mode and have bootloop on.
In HardBrick it shouldn't do anything.
Rafaaaay said:
Now What....
But it is starting into download mode and have bootloop on.
In HardBrick it shouldn't do anything.
Click to expand...
Click to collapse
Sorry no clue. But that showing up is either hard brick or will require more than just flashing back to stock. I think there is a "unbrick" guide for that in the G3 section.
Rafaaaay said:
Now What....
But it is starting into download mode and have bootloop on.
In HardBrick it shouldn't do anything.
Click to expand...
Click to collapse
@Rafaaaay Dude did you found a fix yet? Really hope you had. If not did you try to reinstall back to stock? This is what I had done when I was stuck in the boot loop issue on one of my nexus device
Right after I updated my D850 to MM, my GPS doesn't get a fix on location properly. Sometimes it just does not work and sometimes when it does work it points me the wrong way. I've never had this issue before, the GPS also does not seem to be live too, meaning that it doesn't update constantly. Instead it jumps every 10-15 seconds. Am I the only one with the issue? :crying: :crying:
SnowTauren said:
Right after I updated my D850 to MM, my GPS doesn't get a fix on location properly. Sometimes it just does not work and sometimes when it does work it points me the wrong way. I've never had this issue before, the GPS also does not seem to be live too, meaning that it doesn't update constantly. Instead it jumps every 10-15 seconds. Am I the only one with the issue? :crying: :crying:
Click to expand...
Click to collapse
Did you try performing a factory reset?
Sent from my iPhone using Tapatalk
Twice, but the problem persists.
Edit: I did the hard reset through phone but didn't downgrade-reset to factory using PC if that's what you meant.
SnowTauren said:
Twice, but the problem persists.
Edit: I did the hard reset through phone but didn't downgrade-reset to factory using PC if that's what you meant.
Click to expand...
Click to collapse
So you wiped everything? Strange that should fix any software issues.
Sent from my iPhone using Tapatalk
hyelton said:
So you wiped everything? Strange that should fix any software issues.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
I can definitely see this being a software problem with marshmallow. Ever since downloading it on my LG G3 D850 it can barley read sim cards anymore, and since D850 (as far as I know) can't downgrade I'm screwed.
FreshToast6000 said:
I can definitely see this being a software problem with marshmallow. Ever since downloading it on my LG G3 D850 it can barley read sim cards anymore, and since D850 (as far as I know) can't downgrade I'm screwed.
Click to expand...
Click to collapse
If it can barely read SIM cards that's a hardware issue. Software wouldn't cause that. What do you mean you cannot downgrade? Yes you can.. You just follow my guide and use LGUP and flash kitkat.
Sent from my iPhone using Tapatalk
hyelton said:
If it can barely read SIM cards that's a hardware issue. Software wouldn't cause that. What do you mean you cannot downgrade? Yes you can.. You just follow my guide and use LGUP and flash kitkat.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Does not work for me because the model shows up as "Unknown"
FreshToast6000 said:
Does not work for me because the model shows up as "Unknown"
Click to expand...
Click to collapse
And where did you download LGUP? You must download the correct one or it will show unknown
Sent from my iPhone using Tapatalk
Just did another factory reset, the problem is still there . I've never rooted or tinkered with this phone other than installing OTA update, I don't know why I'd get this problem.
hyelton said:
And where did you download LGUP? You must download the correct one or it will show unknown
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Your post says "To Downgrade/upgrade to/from MM 6.0 You'll need to use LGUP in Post #3 Currently only for the D855". It won't work on D850 right?
SnowTauren said:
Your post says "To Downgrade/upgrade to/from MM 6.0 You'll need to use LGUP in Post #3 Currently only for the D855". It won't work on D850 right?
Click to expand...
Click to collapse
Yes it does work I haven't updated the Op. The only reason it might not work is show unknown and cannot detect phone if you don't download LGUP with the proper dll
Sent from my iPhone using Tapatalk
hyelton said:
Yes it does work I haven't updated the Op. The only reason it might not work is show unknown and cannot detect phone if you don't download LGUP with the proper dll
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
It's not working for me! I've attached screenshots below. I made sure I have the proper dll and that I connected to usb 2. I'm still getting model information check fail error!
Please help
SnowTauren said:
It's not working for me! I've attached screenshots below. I made sure I have the proper dll and that I connected to usb 2. I'm still getting model information check fail error!
Please help
Click to expand...
Click to collapse
The phone is in download mode correct??
Sent from my iPhone using Tapatalk
hyelton said:
The phone is in download mode correct??
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
The phone shows little icon for download mode and then after 2-3 seconds it comes to a page that says Firmware Update with a USB icon. And below it says "Do not unplug the USB connection until the process is complete" with a progress bar.
SnowTauren said:
The phone shows little icon for download mode and then after 2-3 seconds it comes to a page that says Firmware Update with a USB icon. And below it says "Do not unplug the USB connection until the process is complete" with a progress bar.
Click to expand...
Click to collapse
Okay yes that's download mode. Did you choose board_dl?
Sent from my iPhone using Tapatalk
hyelton said:
Okay yes that's download mode. Did you choose board_dl?
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
No I left the default Upgrade DL in action mode, was I supposed to change it?
SnowTauren said:
No I left the default Upgrade DL in action mode, was I supposed to change it?
Click to expand...
Click to collapse
You don't have to but it's recommended if there's issues
Sent from my iPhone using Tapatalk
So after flashing my D850 from 4.4.2 to 7.0, I cannot access TWRP recovery. Ever since I flashed the rom, I keep getting these 3 errors:
"boot certification verify
secure booting error
cause:boot certification verify".
I can still boot into 7.0, but it's not fully functional. It's missing apps, functions, keeps crashing, etc.
Any suggestions to fixing this?
Huz416 said:
So after flashing my D850 from 4.4.2 to 7.0, I cannot access TWRP recovery. Ever since I flashed the rom, I keep getting these 3 errors:
"boot certification verify
secure booting error
cause:boot certification verify".
I can still boot into 7.0, but it's not fully functional. It's missing apps, functions, keeps crashing, etc.
Any suggestions to fixing this?
Click to expand...
Click to collapse
Only solution is to flash back to stock. CM normally seems to loose access to twrp. Not sure if there's a simple way of getting it back but normally all I know is flashing back to stock
Sent from my iPhone using Tapatalk
Thank for replying. Is there a good tutorial out there you can post on how to flash back to stock rom please? My current 7.0 rom won't even let be root my device.
hyelton said:
Only solution is to flash back to stock. CM normally seems to loose access to twrp. Not sure if there's a simple way of getting it back but normally all I know is flashing back to stock
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Thank for replying. Is there a good tutorial out there you can post on how to flash back to stock rom please? My current 7.0 rom won't even let be root my device.
Huz416 said:
Thank for replying. Is there a good tutorial out there you can post on how to flash back to stock rom please? My current 7.0 rom won't even let be root my device.
Click to expand...
Click to collapse
There's a back to stock guide in the general section.
Sent from my iPhone using Tapatalk
hyelton said:
There's a back to stock guide in the general section.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Would it be possible for you to post a link please? I'm new to this website and I cannot find it.
Huz416 said:
Would it be possible for you to post a link please? I'm new to this website and I cannot find it.
Click to expand...
Click to collapse
https://forum.xda-developers.com/showthread.php?t=2785089
You would follow the tot method, and be sure to choose board_dl when you choose the tot and dll file in the software
Sent from my iPhone using Tapatalk
hyelton said:
Only solution is to flash back to stock. CM normally seems to loose access to twrp. Not sure if there's a simple way of getting it back but normally all I know is flashing back to stock
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
hyelton said:
https://forum.xda-developers.com/showthread.php?t=2785089
You would follow the tot method, and be sure to choose board_dl when you choose the tot and dll file in the software
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
board_dl meaning this link, right? http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/
Huz416 said:
board_dl meaning this link, right? http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/
Click to expand...
Click to collapse
That's where your firmware will be use but board_dl is a setting in flashtool
Sent from my iPhone using Tapatalk
hyelton said:
That's where your firmware will be use but board_dl is a setting in flashtool
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Oh, okay. I'll try it out tonight and will get back to you if I need anymore help. Thank you so much.
hyelton said:
That's where your firmware will be use but board_dl is a setting in flashtool
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
The only problem I'm having is that I can't change the port settings. My PC recognizes my G3 as "AOSP on D850".
Huz416 said:
The only problem I'm having is that I can't change the port settings. My PC recognizes my G3 as "AOSP on D850".
Click to expand...
Click to collapse
So you can change the port under device manager? What's the error?
Sent from my iPhone using Tapatalk
hyelton said:
So you can change the port under device manager? What's the error?
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
After clicking on my device under portable devices in device manager, the only options I get are general, driver, details, events, power management. I'm using Windows 10 to do this.
Huz416 said:
After clicking on my device under portable devices in device manager, the only options I get are general, driver, details, events, power management. I'm using Windows 10 to do this.
Click to expand...
Click to collapse
It wouldnt be under portable devices, it would be under Communication Ports. If you don't see that you would need to unhide them
hyelton said:
It wouldnt be under portable devices, it would be under Communication Ports. If you don't see that you would need to unhide them
Click to expand...
Click to collapse
I'm honestly about to throw my phone against a wall right now. I cannot boot into download mode anymore, my computer won't allow me change the port settings, the only thing I can do is enter the rom. USB debugging still works and I can transfer files, but everything else is broken.
Huz416 said:
I'm honestly about to throw my phone against a wall right now. I cannot boot into download mode anymore, my computer won't allow me change the port settings, the only thing I can do is enter the rom. USB debugging still works and I can transfer files, but everything else is broken.
Click to expand...
Click to collapse
So your using a USB 2.0 only port right when trying to put the device into download mode?
I still dont understand why your saying it wont allow you to change the port settings? I've never ever seen this. If the port is there you can change it. Remmeber your phone HAS to be in download mode for the com port to show up to change it to com41. Why not try LGUP?
hyelton said:
So your using a USB 2.0 only port right when trying to put the device into download mode?
I still dont understand why your saying it wont allow you to change the port settings? I've never ever seen this. If the port is there you can change it. Remmeber your phone HAS to be in download mode for the com port to show up to change it to com41. Why not try LGUP?[/QUOTE
Thank you, I was using the wrong USB port. It's currently installing the device. What is LGUP?
Click to expand...
Click to collapse
Huz416 said:
hyelton said:
So your using a USB 2.0 only port right when trying to put the device into download mode?
I still dont understand why your saying it wont allow you to change the port settings? I've never ever seen this. If the port is there you can change it. Remmeber your phone HAS to be in download mode for the com port to show up to change it to com41. Why not try LGUP?[/QUOTE
Thank you, I was using the wrong USB port. It's currently installing the device. What is LGUP?
Click to expand...
Click to collapse
LGUP is part of the back to stock guide. Theres KDZ flash tool, TOT flashtool, and LGUP which flashes both tot and kdz files.
Click to expand...
Click to collapse
hyelton said:
Huz416 said:
LGUP is part of the back to stock guide. Theres KDZ flash tool, TOT flashtool, and LGUP which flashes both tot and kdz files.
Click to expand...
Click to collapse
It says it's only for the D855 model? Not D850?
Click to expand...
Click to collapse
Huz416 said:
hyelton said:
So your using a USB 2.0 only port right when trying to put the device into download mode?
I still dont understand why your saying it wont allow you to change the port settings? I've never ever seen this. If the port is there you can change it. Remmeber your phone HAS to be in download mode for the com port to show up to change it to com41. Why not try LGUP?[/QUOTE
Thank you, I was using the wrong USB port. It's currently installing the device. What is LGUP?
Click to expand...
Click to collapse
Huz416 said:
hyelton said:
It says it's only for the D855 model? Not D850?
Click to expand...
Click to collapse
Its for every model
Click to expand...
Click to collapse
Click to expand...
Click to collapse
I have both the h901 and h900. I updated my 901 to Nougat, and in the same thread the Dev says it is possible to use on the 900. Anyone tried this or willing to try?? My wife uses the h900, sooooo, if I screw that up I'm sleeping on the couch..
https://forum.xda-developers.com/showthread.php?t=3638750
Sent from my LG-H901 using XDA-Developers Legacy app
Hi
I tried to use it, but I am unable to boot into any recovery and if I try "and reboot boot loader" the h900 just reboots back into MM.
I am currently on H90021w.
Sent from my LG-H901 using Tapatalk
The instructions say to cd into directory /dev/block/bootdevice/... but you need to be root to cd into this directory.
Just for grins I tried to do some adb commands on mine, after adb reboot, I got the android with a red triangle and from that point couldn't issue adb commands..
Sent from my LG-H901 using XDA-Developers Legacy app
bobbylx said:
I have both the h901 and h900. I updated my 901 to Nougat, and in the same thread the Dev says it is possible to use on the 900. Anyone tried this or willing to try?? My wife uses the h900, sooooo, if I screw that up I'm sleeping on the couch..
https://forum.xda-developers.com/showthread.php?t=3638750
Click to expand...
Click to collapse
My ATT H900 is still on lollipop and is rooted. Do you think this would work on my phone and if so, what steps do you think I should follow?
TayzGpa said:
My ATT H900 is still on lollipop and is rooted. Do you think this would work on my phone and if so, what steps do you think I should follow?
Click to expand...
Click to collapse
I can't really say. My H900 was rooted and on LP, but I upgraded it back in January. Now when I try to do anything with ADB, nothing works and my PC doesn't even recognize it. My plan was to follow the Dev's directions, only pushing system.img and boot.img.
I may try again later
Waiting for good news... ?
TayzGpa said:
My ATT H900 is still on lollipop and is rooted. Do you think this would work on my phone and if so, what steps do you think I should follow?
Click to expand...
Click to collapse
You may want to send a message to the Dev over in the H901 section. Here is what he told me just today. Sounds like you are at the right point according to him.
Quote:
Originally Posted by runningnak3d
@bobbylx @Stransky To use this on an H900 you have to already be rooted. It is my understanding that only people that had orignal LP have root? Dirtycow doesn't work on MM on H900? That doesn't make sense. Where does the dirtycow root procedure fail on the H900?
Stransky said:
Hi
I tried to use it, but I am unable to boot into any recovery and if I try "and reboot boot loader" the h900 just reboots back into MM.
I am currently on H90021w.
Click to expand...
Click to collapse
I have the same phone h900 with same mm firmware but i have a bit of a problem i cant open security and fingerprints section in settings ...