I was running stock 4.4.2, rooted and unlocked, and my service/data were fine until today, when I just stopped being able to use data. I've tried rebooting, powering down for about half an hour, checked and double checked my APNs, and flashed Cm11. Haven't tried to flash a new radio alone since I figured cm11 would've come with a different radio from stock. A friend suggested it might be my SIM, but I would assume I would get no service at all if there was a problem there.
So where do I go from here? :V
Nexein said:
I was running stock 4.4.2, rooted and unlocked, and my service/data were fine until today, when I just stopped being able to use data. I've tried rebooting, powering down for about half an hour, checked and double checked my APNs, and flashed Cm11. Haven't tried to flash a new radio alone since I figured cm11 would've come with a different radio from stock. A friend suggested it might be my SIM, but I would assume I would get no service at all if there was a problem there.
So where do I go from here? :V
Click to expand...
Click to collapse
Who is your carrier. Go to mobile networks/access point names/ and find your apn settings
Try proper radio. A sign is if your WiFi doesn't find signal usually bad mixed. I get this often. I flash lots on many devices but its simple. Anyway try your radio. And no ROMs normally have no radio unless it says otherwise or firmware. Peace.
Sent from my N3 using XDA Free mobile app
Shckr57 said:
Who is your carrier. Go to mobile networks/access point names/ and find your apn settings
Click to expand...
Click to collapse
AT&T, I've tried resetting to default APNs as well as comparing mine to those in AT&T's Help and other peoples' own settings.
Droid2drummer said:
Try proper radio. A sign is if your WiFi doesn't find signal usually bad mixed. I get this often. I flash lots on many devices but its simple. Anyway try your radio. And no ROMs normally have no radio unless it says otherwise or firmware. Peace.
Sent from my N3 using XDA Free mobile app
Click to expand...
Click to collapse
See I can pick up wifi just fine, it's just my regular data that's acting up. I've tried looking into a guide for flashing radios but to be honest, I don't know much about LTE bands or anything. Is there a good guide here that I missed? It seems as simple as flashing one with CWR but I don't wanna ruin anything.
Write down your apn settings here so we can look at them
Name: ATT LTE
APN: Phone
Proxy blank
Port blank
UN blank
PW blank
Server blank
MMSC: ht tp:// mmsc. mobile. att. net
MMS proxy: proxy. mobile. att. net
MMS port: 80
MCC: 310
MNC: 410
Auth blank
APN protocol: IPv4
APN roam: IPv4
APN Enabled
Bearer unspecified
MVNO type: None
Nexein said:
Name: ATT LTE
APN: Phone
Proxy blank
Port blank
UN blank
PW blank
Server blank
MMSC: ht tp:// mmsc. mobile. att. net
MMS proxy: proxy. mobile. att. net
MMS port: 80
MCC: 310
MNC: 410
Auth blank
APN protocol: IPv4
APN roam: IPv4
APN Enabled
Bearer unspecified
MVNO type: None
Click to expand...
Click to collapse
-3G Settings-
Name: ATT
APN: wap.cingular
Proxy: <Leave in Blank>
Port: <Leave in Blank>
Username: [email protected]
Password: cingular1
Server: <Leave in Blank>
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: <Leave in Blank>
APN type: default,supl,mms
APN Protocol: Leave it to the Default one
-4G Settings-
Name: ATT HSPA+
APN: phone
Proxy: <Leave in Blank>
Port: <Leave in Blank>
Username: <Leave in Blank>
Password: <Leave in Blank>
Server: <Leave in Blank>
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Authentication type: <Leave in Blank>
APN type: default,supl,mms,hipri
APN Protocol: Leave it to the Default one
Bearer: leave it to the Default one
Should I delete the other ones and just have those two? Cm11 came with like a bunch of them.
Nexein said:
Should I delete the other ones and just have those two? Cm11 came with like a bunch of them.
Click to expand...
Click to collapse
You can have as many as you like but it will only use one. It looks as if you are mixing the settings of different apns together
Shckr57 said:
You can have as many as you like but it will only use one. It looks as if you are mixing the settings of different apns together
Click to expand...
Click to collapse
Added both, tried selecting each one and I'm still having the same problem.
So to update, I've gone back to stock 4.4.4, straight from google, still not working, and then flashed the newest radio and that didn't do it either. Starting to thing it's a hardware problem, maybe actually is the SIM?
Ended up being the sim! Thanks for your help though, guys!
Related
I recently flashed to the uclf5 galaxy S3 r4 rom with mohans kernel and I love it. The only problem is the Data connections. The original APN that installed in the flash would connect and had great speeds but would not allow me to send or receive picture messages. Standard text's were ok but no pictures.
I looked around google and the XDA forums and tried a couple of new APN's. I finally got one that would connect and send pictures but it wasn't connecting to 4G LTE only 4G, 1st world problems yes but I wanted the LTE. as I continued searching I managed to get one to connect to LTE and still send pictures and everything was working perfectly, Except now the phone randomly disconnects from all connections with a little circle with a line through it instead of connection bars and obviously no data or phone calls. If I toggle back and forth between APN's I can get it to connect again but it's very intermittent sometimes it'll stay connected for hours other times for just minutes.
I originally had the SKYICS Superlite Rom installed and didn't have any connection issues what so ever and i'm completely at a loss as to what's going on now.
Original APN Settings
Name: ATT Phone
APN: phone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not Set
MMSC: http ://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication Type: None
APN type: default,mms,supl
APN protocol: IPv4
Allows Picture messaging but no LTE
Name: ATT
Phone
APN: wap.cingular
Proxy: Not Set
Port: Not set
Username: WAP @CINGULARGRPS.COM
Password: (Forgot but it's there)
Server: Not Set
MMSC: mmsc.cingular.com
MMS Proxy: 66.209.11.32
MMS Port: 80
MCC: 310
MNC: 410
Authentication Type: None
APN type: default,mms,supl
APN protocol: IPv4
Allows Picture Messaging and LTE
Name: ATT LTE
APN: phone
Proxy: Not Set
Port: Not set
Username: Not set
Password: Not set
Server: Not Set
MMSC: Not set
MMS Proxy: Not set
MMS Port: Not set
MCC: 310
MNC: 410
Authentication Type: None
APN type: default,mms,supl
APN protocol: IPv4
I'm not sure how that last one works but it does.
These settings do work, but again pretty much at will. this morning i woke up and was conected to edge. that was scary...
I'm not sure if its my settings or tge radio or something else entirely. any help would be greatly appreciated.
I've been having the same problem. Everything will work for a few seconds then I get a "null cell state delivered" message when I check logcat. Changing APNs didn't work for me but how are you getting to the APN settings? Every time I try I just get a dialog box that tells me to insert a sim card.
I just bought this used skyrocket yesterday. Everything was working fine after I bought it including the 4G mobile data. Today, I called at&t to register the phone on my account and switch my data plan to LTE. They said the phone is clean and made the changes for me. I then decided to perform a factory data reset to get rid of the previous user's stuff. After the reset, everything works EXCEPT mobile data. I've tried everything -- powering the phone off/on, turning packet data off/on, airplane mode off/on, removing/replacing the SIM. I called at&t back and they said the phone is still clean, it's not been reported stolen and it's not blacklisted.
The seller told me he had a custom rom on it at one point, but he restored it to factory condition. I went into recovery mode and it still has the stock recovery so I'm assuming it's not rooted nor does it have a custom rom.
Any idea what the problem might be?
Thanks,
dw
You are gonna need a 4g Sim card. They should've told you that on the phone. Also check that you have data packets enabled
Did you check your APN?
--------------------------------------------------------------------
Sent from my Skyrocket i727 running Team Dirt
--------------Nexus 7 running AOKP PUB--------------
That was it! My APN settings were completely blank. I used these settings from another thread
Name: ATT LTE
APN: pta
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: httpcolon//mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Auth type: Not set
APN type: internet + mms
APN protocol: IPv4
Enable/diable APJ: APN enabled
Bearer: Unspecified
Works great now. Thanks for your help.
dwestall said:
That was it! My APN settings were completely blank. I used these settings from another thread:
Name: ATT PTA
APN: pta
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: httpcolon//mmsc.mobile.att.net
MMS proxy: proxy.att.net
MMS port: 80
MCC: 310
MNC: 410
Auth type: Not set
APN type: internet + mms
APN protocol: IPv4
Enable/diable APJ: APN enabled
Bearer: Unspecified
Works great now. Thanks for you help.
Click to expand...
Click to collapse
Make sure u thank Mike :good:
i have a carrier unlocked One S, which used to be T-Mobile, now it's on AT&T. i remembered from when i had the One X that i had to setup a APN, so i found the necessary information and create one, worked fine, actually set it up a couple of times no problem. so today after i redid my phone again i create the APN, and now i can't get higher than 2G (tested in several locations) anyone any idea how i can resolve this?
(see attached image)
here's the content of the APN;
Name: AT&T HSPA+
APN: phone
Proxy: Blank
Port: Blank
Username: blank
Password: blank
Server: blank
MMSC: http://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication type: Blank
APN Type: default,supl,mms,hipri
APN protocol: leave as is
Bearer: leave as is
Click to expand...
Click to collapse
thanks in advance.
As far as I know, HTC One S DOESN'T support 4G (at least mine S3 variant doesn't). And if 3G isn't working also at locations where it should, are you sure you have the WSM/GSM mode, not only checked one of these?
Edit: Found out that this may be a hardware issue that happens after S-OFFING and/or SIM UNLOCKing
check this thread http://forum.xda-developers.com/showthread.php?t=2160389
it may be helpful
thanks guys... had some other issues and the seller is going to send me another One S... we'll see how that goes.
Hi all,
recently I got my new phone Hisense A2 pro imported, but can't get it set up right. It's not the original ROM.
2g, 4g is written at the upper lefter corner and I can get SMS, but no internet connection. I think the APN settings are wrong, but I'm not sure and tried different settings. Does it sound as if it's a problem with the APN or could it be something else My recent settings are:
Name: o2 internet
APN: internet
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: 10.81.0.7:8002
MMS proxy: 82.113.100.5
MMS port: 8080
MCC: 262
MNC: 07
Authentication type: None
APN type: default,supl,mms
APN protocol: IPv4/IPv6
APN roaming protocol IPv4
Bearer: Unspecified
MVNO type: None
MVNO value: Not set
Many thanks in advance!
IMinoI said:
Hi all, recently I got my new phone Hisense A2 pro imported, but can't get it set up right. It's not the original ROM...
Click to expand...
Click to collapse
I don't have this device but, I believe that one or both of the following threads may be helpful for what you need and don't be afraid to ask for some member guidance within one of them.
https://forum.xda-developers.com/showthread.php?t=3694644
https://forum.xda-developers.com/showthread.php?t=3673945
Good Luck!
~~~~~~~~~~~~~~~
I DO NOT provide support via PM unless asked/requested by myself. PLEASE keep it in the threads where everyone can share.
...please i would to find a twrp and a custom rom but i sppose it is just a dream. i've just discovered this phone.... sold at onlu 120euro and at this price is incredible but i could not live without a twrp and possibly a custom rom......
IMinoI said:
Hi all,
recently I got my new phone Hisense A2 pro imported, but can't get it set up right. It's not the original ROM.
2g, 4g is written at the upper lefter corner and I can get SMS, but no internet connection. I think the APN settings are wrong, but I'm not sure and tried different settings. Does it sound as if it's a problem with the APN or could it be something else My recent settings are:
Name: o2 internet
APN: internet
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: 10.81.0.7:8002
MMS proxy: 82.113.100.5
MMS port: 8080
MCC: 262
MNC: 07
Authentication type: None
APN type: default,supl,mms
APN protocol: IPv4/IPv6
APN roaming protocol IPv4
Bearer: Unspecified
MVNO type: None
MVNO value: Not set
Many thanks in advance!
Click to expand...
Click to collapse
i have exactly same problem as you, have you solved it？are you in Germany? i'm in germany and my card is also o2, can see 4g but no data connection. But i have tried my girlfriend's card(Eplus), it worked. i may switch my provider
The most common issue I have run into with the GSI roms for the E5 Play (james) has been data not working, unfortunately all of the sprint APN settings I have found online have been incorrect for newer phones so here is a working APN based off of a stock E5 Play.
Name: internet
APN: x.ispsn
Proxy: Not Set
Port: Not Set
Username: Not Set
Password: Not Set
Server: Not Set
MMSC: http://mms.sprintpcs.com
MMS Proxy: oap7.sprintpcs.com
MMS Port: 80
MCC: 310
MNC: 120
Authentication Type: Not Set
APN Type: default,supl,mms,cbs,ia
APN Protocol: IPv4/IPv6
APN Roaming Protocol: IPv4
APN Enable/Disable: APN Enabled
Bearer: eHRPD, LTE
MVNO Type: None
If this helps you hit the Thanks button
Wow, I've been trying to fix this for a while now... I can finally go to sleep oh my lord... Thank you so much sir. One question though know how to make these apn settings stay even after rebooting?
sonymicronin said:
Wow, I've been trying to fix this for a while now... I can finally go to sleep oh my lord... Thank you so much sir. One question though know how to make these apn settings stay even after rebooting?
Click to expand...
Click to collapse
I haven't had an issue with them not sticking after a reboot, I'll look into it and let you know if I figure something out.