Database Info

[Q] Rom needed for live with Walkman WT19i

Friends suggest me a good stable Rom for wt 19 i
Thanks in advance!

fanaticprakash said:
Friends suggest me a good stable Rom for wt 19 i
Thanks in advance!
Click to expand...
Click to collapse
hybroman 12 which i am using right now is extremely stable, everything working..
otherwise the cm 7.2 fxp 108 is stable too but without the stereo speaker and the walkman button..
performance wise, cm 7.2 is much better, with higher benchmarks
---------- Post added at 12:36 PM ---------- Previous post was at 12:35 PM ----------
fanaticprakash said:
Friends suggest me a good stable Rom for wt 19 i
Thanks in advance!
Click to expand...
Click to collapse
if you want to overclock, use rage kernel

Thanks Buddy!
could you give me the instructions to install hybroman 12..

fanaticprakash said:
could you give me the instructions to install hybroman 12..
Click to expand...
Click to collapse
just follow the ones given on the hybrom download site, it's pretty clear exact words,
Installation instructions
Needs unlocked bootloader
(actually hybrom does not contain a boot image.Thus, when you install hybrom you don't mess with your boot image at all.BUT recovery from nAa is installed in /system and while system is formated during the installation of hybrom,recovery messes with it self.That's why unlocked bootloader is necessary for now to install hybrom)
Copy the zip file to your SD card
Reboot your device in CWM
Make a full data wipe-factory reset
Wipe cache and Dalvik cache
Choose install zip from sd card
Wait for installation to end
Reboot
(First reboot after installation might take a while and screen gets totally black after boot animation is displayed for about a minute or twnly on first reboot)
Reboot a second time
Enjoy!
(If anyone gets stuck at se logo at first reboot,he should try this also: First make the data wipe, then install,then shutdown the device.Turn it on after about 10sec)
(Tested and confirmed by chrisbymoningka for v7)

Got some doubts..
1)What is the use of changing kernal??
2)please give me instructions to unlock the boot loader..
3)How to get CWM By installing Xrecovery or some otherway?
thank you

fanaticprakash said:
1)What is the use of changing kernal??
2)please give me instructions to unlock the boot loader..
3)How to get CWM By installing Xrecovery or some otherway?
thank you
Click to expand...
Click to collapse
1. changing kernel lets you overclock your phone, like use it at 1.2ghz, when you need it, i do not suggest it, as it decreases the battery life by a lot. also cpu governors, which is like the clock is limited to 600mhz at night, thus saving battery..
2. go to http://unlockbootloader.sonyericsson.com/ easy instructions given. remember this voids your warranty..
3.the custom kernels come with preinstalled CWM and root

Since I didn't install any kernel how can l go to cwm for my friend w8 I used x recovery ,but I didn't find x recovery for wt 19i
Sent from my WT19i

Hybrom working fine
thanks for the help i installed hybrom and rage kernal..
its working good....

fanaticprakash said:
Since I didn't install any kernel how can l go to cwm for my friend w8 I used x recovery ,but I didn't find x recovery for wt 19i
Sent from my WT19i
Click to expand...
Click to collapse
when i first installed recovery, it was through this batch script. the script is not mine, i cannot find the original thread where i found it.. read the instructions carefully

Anyway thanks buddy!
I installed the rage kernel first so i got cwm then i install the Hybrom 12 its good thanks Man!!

[Q] Sony Xperia J IMEI Blank with sim no signal

I have a problem with my Sony Xperia J ST26i. It's rooted and unlocked.
Now I can start my mobile but he has no signal. Phone says there is no SIM card. If have my SIM card inserted. I have only wifi signal.
When I dial *#06# on my phone I see the display as shown in the attachment.
And with MTK Droid Tool I can't change/restore my IMEI. See also the screenshot of MTK. It says --- Unknown ROM structure, backup NOT possible!
Is there a another way to restore my IMEI? Also I have no .nv_data file. It's not on my phone. Have anyone this file for My phone or another solution?
Hardware : QCT
Model : ST26i
Build number : 11.2.A.0.31
Build date UTC : 20130419-050845
Android v : 4.1.2
Baseband v: -----
Kernel v : 3.4.0 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 Fri Feb 1 13:04:19 CST 2013
Uboot build v : -----
LCD Driver IC : -----

Sometimes, there are few bugs in stock fw. Like me, i cant turn on wifi. So either u restore using PCC or flash custom rom might help.
Sent from my Xperia Miro using xda premium

kreatonn said:
Sometimes, there are few bugs in stock fw. Like me, i cant turn on wifi. So either u restore using PCC or flash custom rom might help.
Sent from my Xperia Miro using xda premium
Click to expand...
Click to collapse
Thanks for the reply.
PCC restore is not an option. I haven't make one. So I go look on the internet for a custom ROM flash.

If wont work after you flash rom again... just relock and then unlock phone bootloader again!

2010matej said:
If wont work after you flash rom again... just relock and then unlock phone bootloader again!
Click to expand...
Click to collapse
My phone is working again! I went to a phone store in Scheveningen and they have put a rom on my phone back they do work. It's the original stock rom. It cost me €15 bud it's working again. In the future, I'll backup first and the go play with my phone.
Thanks for the support! :good:

Stoetel said:
My phone is working again! I went to a phone store in Scheveningen and they have put a rom on my phone back they do work. It's the original stock rom. It cost me €15 bud it's working again. In the future, I'll backup first and the go play with my phone.
Thanks for the support! :good:
Click to expand...
Click to collapse
15€ for this? OMG man! YOu can do that alone for free,just use flashtool !

Hi. I have a similar problem.
Phone (xperia J) is working fine with stock rom, rooted and unlocked bootloader. But when i flash custom rom there is no IMEI, no signal and no efs folder (nv_data file). And if I go back to stock rom the IMEI is back and mobile network works.
So my question is is there any way to transfer IMEI, recreate efs folder, so I can use custom roms?

I have to post 10 times before I can post links outside this forum.

Stoetel said:
I have to post 10 times before I can post links outside this forum.
Click to expand...
Click to collapse
And I have to wait five minutes.
Well just posting...

Stoetel said:
And I have to wait five minutes.
Well just posting...
Click to expand...
Click to collapse
Just keep calm. The solution is near.

Stoetel said:
Just keep calm. The solution is near.
Click to expand...
Click to collapse
Another post...

Stoetel said:
Another post...
Click to expand...
Click to collapse
Three to go...

Stoetel said:
Three to go...
Click to expand...
Click to collapse
Almost.
Scroll down ....

Stoetel said:
Almost.
Scroll down ....
Click to expand...
Click to collapse
After this post the solution!

mtommy88 said:
Hi. I have a similar problem.
Phone (xperia J) is working fine with stock rom, rooted and unlocked bootloader. But when i flash custom rom there is no IMEI, no signal and no efs folder (nv_data file). And if I go back to stock rom the IMEI is back and mobile network works.
So my question is is there any way to transfer IMEI, recreate efs folder, so I can use custom roms?
Click to expand...
Click to collapse
Use it at your own risk. Read this text first before you get started.
If you follow these steps your phone is back to the original settings. You have your signal back and you IMEI.
Now you want your phone rooted! Right? Right!
For rooting Sony Xperia J 11.0.A.7.5 version, 11.2.A.0.21, 11.2.A.0.31 (and or later) using ClockworkMod (CWM) recovery necessitating an unlocked bootloader (unlocked bootloader).
Broadly speaking, the rooting procedure using CWM recovery to install su, busybox and Superuser.apk files bundled in the update. The steps are: flash CWM, rooting package update using CWM recovery, then flash the stock kernel back.
Preparation:
1. Fastboot files here
2. Unlock Boatloader.
3. CWM Sony Xperia J (boot.img)
4. Sony Xperia J stock kernel 11.0.A.7.5 (kernel.sin), can be extracted from the image ftf.
5. Update file for rooting (root_xperia_signed.zip
Update March 8, 2013:
All the required files in the download is packaged in the following:
- Version 11.0.A.7.5
- Version 11.2.A.0.21
- Version 11.2.A.0.31 (May 30, 2013)
The steps:
1. Root_xperia_signed.zip copy files to the internal / external sdcard.
2. Prepare boot.img, kernel.sin, fastboot.exe into the working folder. (Make self a folder on you PC Harddisk)
3. Prepare boot.img, kernel.sin, fastboot.exe into the working folder.
Turn off the phone, unplug the USB cable and go into fastboot mode by pressing and holding down the Vol + Up while plugging in the USB cable, fastboot mode can be seen from the blue LED light on the top panel.
4. Check whether the connection is correct fastboot, type in Command Prompt:
fastboot getvar version​
If prompt <waiting for device> is displayed, then the connection is not successful, try to check whether the driver for fastboot already installed.
5. Flash CWM and restart the phone:
fastboot flash boot boot.img
fastboot reboot​
6. When the phone restarts, observe the LED on the bottom of the panel when it turns purple, immediately press and hold the Vol + Up button until the LED turns blue to get into CWM. USB cable can then be removed.
7. At CWM, select install zip from sdcard, then choose zip from sdcard / external sdcard and select the file in step 1 above. Continue reboot system now and turn off the phone (if necessary by removing the battery and repeat to enter fastboot mode).
8. Repeat steps 3 and 4.
9. Flash stock kernel:
fastboot flash boot kernel.sin
fastboot reboot​
10. Turn on the phone, check whether the application is installed SuperSU. Congratulations rooting successful.
Originaly posted 11th July by Hamzie Fickri
This text comes from this page.

Thanks, but that's not what i needed.
I already have stock rom rooted and working. Problem is if I install custom rom (FXP, PA), rom starts but no mobile signal and no IMEI. So I cannot use it.
Is there a way to like "copy/paste" IMEI from stock rom to custom rom?
edit: read somewhere on xda that this is a CM10 bug and CM10 based roms for xperia J.

disregard my last post (and previous post also)
fixed it!
what I did:
1. flash original stock ICS rom - 11.0.A.7.5.CE
2. reboot phone and then shutdown (not sure if this is necessary)
3. flash CWM img from http://forum.xda-developers.com/showthread.php?t=2034639
4. install custom rom (FXP233)
5. reboot
and now mobile signal works and IMEI is back.
hope it helps somebody and sorry for hijacking your thread Stoetel

mtommy88 said:
disregard my last post (and previous post also)
fixed it!
what I did:
1. flash original stock ICS rom - 11.0.A.7.5.CE
2. reboot phone and then shutdown (not sure if this is necessary)
3. flash CWM img from http://forum.xda-developers.com/showthread.php?t=2034639
4. install custom rom (FXP233)
5. reboot
and now mobile signal works and IMEI is back.
hope it helps somebody and sorry for hijacking your thread Stoetel
Click to expand...
Click to collapse
No problem!
The importent thing is, your mobile is working fine again! :good:
Thanks for the response.

Is there any solution about this problem on tipo?
Sent from my ST21i using xda app-developers app

tassosmer said:
Is there any solution about this problem on tipo?
Sent from my ST21i using xda app-developers app
Click to expand...
Click to collapse
Here you can find the latest Android 4.0.4 version for the Sony Xperia Tipo ST21
And here the CWM for Tipo.
Kernel can you extract from the ftf file. You can open th ftf file with Winzip or Winrar.
Flashtool. You can also use this program to check if your phone is bootlocked.
Go check this site if you need your phone to unlock the bootloader.
Follow the instructions above in the previous post. Or search on this forum for the solution.
Good luck.

[Q] Xperia E CM10 - Battery stuck @ 100%

Hey. I have this Xperia E C1504 (currently using C1505 stock). I installed CM10 on it some time ago, and I noticed that the battery level was stuck at 100%. This even caused the battery to be used beyond capacity and I had to get my phone fixed at the Sony service center (I relocked the bootloader for the trip).
Why did this happen? Why was the battery stuck at 100%? Anybody? The ROM I used is this one: http://forum.xda-developers.com/showthread.php?t=2330638
EDIT: Forgot to mention this, but the battery works awesomely in stock.

Bump. Nobody? Please? I really want CM10, it was awesome while I had it.

Try to reflash kernel
Sent from my Xperia E dual using Tapatalk

Abadguy10 said:
Try to reflash kernel
Sent from my Xperia E dual using Tapatalk
Click to expand...
Click to collapse
Happened both times I installed CM10. I may try the FXP version, or the jjm34 version with the FXP kernel. Thanks, though! Will report back.

NSDCars5 said:
Happened both times I installed CM10. I may try the FXP version, or the jjm34 version with the FXP kernel. Thanks, though! Will report back.
Click to expand...
Click to collapse
jjm34 version is for E dual only and try to flash joebonrichie's kernel with fxp.
Sent from my Xperia E dual using Tapatalk

Abadguy10 said:
jjm34 version is for E dual only and try to flash joebonrichie's kernel with fxp.
Click to expand...
Click to collapse
He has a single-SIM version too. I'm downloading FXP244 right now, will report back.

Nope, nothing. Stuck at CyanogenMod bootscreen for ages.

Choose a different FXP version then,

Problem solved! Like an idiot, I forgot to format /data and /cache.
Thanks a lot, @Abadguy10 and @fonetalker101!

NSDCars5 said:
Problem solved! Like an idiot, I forgot to format /data and /cache.
Thanks a lot, @Abadguy10 and @fonetalker101!
Click to expand...
Click to collapse
I am experiencing the same problem. Using jim34 version on a 1505 single. The FXP version caused my sim card not to be recognized.
What version does work for you now and how did you manage to eliminate the battery problem?

nylki said:
I am experiencing the same problem. Using jim34 version on a 1505 single. The FXP version caused my sim card not to be recognized.
What version does work for you now and how did you manage to eliminate the battery problem?
Click to expand...
Click to collapse
As said above, format /data and /cache before flashing the ROM. Also, try the kernel from hsr0's ROM (what this means, is that you need to download hsr0's ROM, open it with WinRAR or 7-zip, take out the boot.img, and flash it with fastboot).

NSDCars5 said:
As said above, format /data and /cache before flashing the ROM. Also, try the kernel from hsr0's ROM (what this means, is that you need to download hsr0's ROM, open it with WinRAR or 7-zip, take out the boot.img, and flash it with fastboot).
Click to expand...
Click to collapse
Thanks! Using hsr0's ROM fixed the problem (actually it is a continuation of jim34's ROM). for reference, its here:
http://forum.xda-developers.com/showthread.php?t=2518451
It works with my Xperia E single sim version.

nylki said:
Thanks! Using hsr0's ROM fixed the problem (actually it is a continuation of jim34's ROM). for reference, its here:
http://forum.xda-developers.com/showthread.php?t=2518451
It works with my Xperia E single sim version.
Click to expand...
Click to collapse
Really? My phone must be a rare one, cause hsr0's ROM doesn't work properly in my phone, but jjm34's with hsr0's kernel does. Strange ways how Android works...

NSDCars5 said:
Really? My phone must be a rare one, cause hsr0's ROM doesn't work properly in my phone, but jjm34's with hsr0's kernel does. Strange ways how Android works...
Click to expand...
Click to collapse
It does.
What i did:
0. wipe data, cache
1. flash stock rom (with flashtool, via usb) and wipe cache, data
2. reboot, shutdown
3. flash hsr0's boot.img with fastboot (via usb)
4. reboot, disconnect usb
5. flash hsr0's ZIP from the recovery boot (cm_nanhu_ds-ota-1.1.0.zip on sdcard)
6. wipe cache, data
7. reboot
8. *jumping around, because it finally works*

nylki said:
It does.
What i did:
0. wipe data, cache
1. flash stock rom (with flashtool, via usb) and wipe cache, data
2. reboot, shutdown
3. flash hsr0's boot.img with fastboot (via usb)
4. reboot, disconnect usb
5. flash hsr0's ZIP from the recovery boot (cm_nanhu_ds-ota-1.1.0.zip on sdcard)
6. wipe cache, data
7. reboot
8. *jumping around, because it finally works*
Click to expand...
Click to collapse
Can you hang up on a phone call? That's the main issue for me; I can't hang up.

NSDCars5 said:
Can you hang up on a phone call? That's the main issue for me; I can't hang up.
Click to expand...
Click to collapse
I just tested all variations of hanging up:
1. getting called -> hanging up before accepting call
2. getting called -> accepting -> hanging up
3. calling myself -> hanging up
all three work for me.

nylki said:
I just tested all variations of hanging up:
1. getting called -> hanging up before accepting call
2. getting called -> accepting -> hanging up
3. calling myself -> hanging up
all three work for me.
Click to expand...
Click to collapse
Well, luck you. None of the three work for me.

Hangin up problem
NSDCars5 said:
Can you hang up on a phone call? That's the main issue for me; I can't hang up.
Click to expand...
Click to collapse
I also experienced same problem.
Flash the kernel again.
and then flash "nanhu-CM10DS-0.8.1.36-ota.zip" find on xda site.
It worked for me..

Aakm said:
I also experienced same problem.
Flash the kernel again.
and then flash "nanhu-CM10DS-0.8.1.36-ota.zip" find on xda site.
It worked for me..
Click to expand...
Click to collapse
Had the solution for a while now, thanks.
Also, if you're using hsr0's kernel, check out Hades kernel in Android development section - it's got overclock to 1.5 Ghz.

CM10 100% Battery fix for sony Experia E Single Sim
NSDCars5 said:
Hey. I have this Xperia E C1504 (currently using C1505 stock). I installed CM10 on it some time ago, and I noticed that the battery level was stuck at 100%. This even caused the battery to be used beyond capacity and I had to get my phone fixed at the Sony service center (I relocked the bootloader for the trip).
Why did this happen? Why was the battery stuck at 100%? Anybody? The ROM I used is this one: http://forum.xda-developers.com/showthread.php?t=2330638
EDIT: Forgot to mention this, but the battery works awesomely in stock.
Click to expand...
Click to collapse
Flash this CM10BatteryFix.img file using fastboot from ADB or any other Application.
It will fix ur 100% battery status issue.
Download from here: http://www21.zippyshare.com/v/56005129/file.html
enjoyyyy!! :good:

[ROM] [E SS/DS] Ultimate CM10 Install Guide!

Ultimate CM10 Install Guide​
Required:
-CM10 Zip (Odexed or Deodexed)
-Unlocked Bootloader
-Flashtool
-11.3.A.2.23 FTF (Single Sim Only)
11.3.A.2.1 FTF (Dual Sim Only)
-USB Cable
-Time
-Patience
-Zues Kernel V3.1
Lets Begin:[/SIZE]
1. Follow this guide to Unlock/Check if Your Bootloader Is Unlockable: http://unlockbootloader.sonymobile.com/
2. Install Flashtool.
3. Install Drivers which are in: C:\Flashtool\drivers\Flashtool-drivers.exe, run the program and install Flashmode and Fastboot Drivers.
4. Move the 11.3.A.2.23 FTF or the 11.3.A.2.1 FTF if your Xperia E is Dual Sim to C:\Flashtool\firmwares folder.
5. Run Flashtool, Click On the Lightning Bolt --> Select Flashmode and Select the 11.3.A.2.23 FTF or 11.3.A.2.1 if your phone is dual sim. and hit OK.
6. It will ask you to put the dervice in Flashmode, (PAY ATTENTION):
Power Down The Device,
Plug One end of the USB Cable into the USB Slot on the PC/Laptop,
Now Press the Volume Down Button and Plug the USB Cable In,
The computer an will recognise your phone and Flashtool (There will be a green led on your phone) will give an error resulting in it saying Install Drivers --> THIS IS OK!
Windows Will Now be installing drivers, let that finish then proceed.
7. Now Unplug the Cable, and do Step 6 and this time it will begin to Flash the FTF.
8. Once its done unplug your phone and this time plug it in while holding the Volume Up Button. (Blue Led)
9. Wait For Windows To Install Drivers then proceed.
10. Click the lightning bolt and this time select FastBoot Mode then select Select Kernel To Flash, in the right hand corner change .sin to .elf and go into the folder where you download Zues V3.1.elf and select it and it will Flash.
11. Once Finished Setup Your Phone Normally.
12. Copy the CM10 Zip to Your SD Card.
13. Power off your phone, power one while tapping the volume up or down button when you see the blue light.
14. Now use the Volume Buttons To Navigate To Wipe Data/Factory Reset and Hit Yes.
15. Now Select Install Zip From SD Card and Flash the CM10 Zip File.
16. Reboot and Enjoy Your CM10.
Download Links:
Flashtool: http://www.flashtool.net
Zues Kernel V3.1: http://forum.xda-developers.com/xperia-j-e/development/e-recovery-stock-11-3-2-23-t2658801
CM10 Zip (Odexed or Deodexed): http://forum.xda-developers.com/xperia-j-e/general/tip-fix-unknown-baseband-issueno-sim-t2674849
11.3.A.2.23 For Single Sim FTF: http://www.mediafire.com/download/3fmmkbmlqtjd6cy/Xperia+E+(C1505)_11.3.A.2.23_Unbranded.ftf
11.3.A.2.1 For Dual Sim FTF: http://www.4shared.com/file/55QLW02n/113A21.html

Cm10 work on Zeus kernel ?? Bugs ??

@UltraGamerHD Zeus on cm10?!?!?!?
XE rom page update coming soon for your guide,turbocs,ares,hades,posiden kernel

Grimlock007 said:
@UltraGamerHD Zeus on cm10?!?!?!?
XE rom page update coming soon for your guide,turbocs,ares kernel
Click to expand...
Click to collapse
This is for people who just got there boot loader unlocked and have no cwm.
Sent from my C1505 using XDA Premium 4 mobile app

Wow, if it works on zeus, then i dont have to flash different kernels when switching between cm10 and termin. But if i am already on 11.3.A.2.23 do i still need to flash it? Gonna try this when i get home
Sent from my C1505 using XDA Premium 4 mobile app

@UltraGamerHD Fixed Bugs ???Or is this Rom ??

DanielFlorin said:
@UltraGamerHD Fixed Bugs ???Or is this Rom ??
Click to expand...
Click to collapse
just an update to the old cm10.....
before: if you have gsm bug ,to fix you had to flash stock ftf again
now: flash rom again and voila! gsm is back
@UltraGamerHD mention stuff about that gsm bug and how to fix ,(in case it happens)
---------- Post added at 11:02 AM ---------- Previous post was at 10:56 AM ----------
UltraGamerHD said:
This is for people who just got there boot loader unlocked and have no cwm.
Sent from my C1505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
aaaaah!
OK, mats had put hsr0 dual recovery boot.img in it.....
you should mention that...
people may try to flash Zues on cm10 afterwards....
@SmashMii no!....but once you flash cm10 rom, zeus gets overwritten....

DanielFlorin said:
@UltraGamerHD Fixed Bugs ???Or is this Rom ??
Click to expand...
Click to collapse
My dear fella. If you had read the thread I made you would know this!
This is the last time I will be saying this:
This is an update of jjm34 for the E dual. Version 1.1.0. Somehow on this version GSM isn't buggy. It is the E dual version, so you will have to select SIM1 as your SIM. The bugs are still the same:
-Video recording not working
-Video streaming not working
-Bluetooth not working(well, it turns on and connects but fails to exchange any media)
-Magnetometer not working(no automatic moving to landscape/portrait.
All right? Clear enough?
This ROM fixes just the GSM and nothing more. It was not made by me or UltraGamerHD. It is an update by jjm34.
Mats

What gets overwritten? I dont exactly understand, please explain to me. What i understand is i can flash cm10 on zeus, but when changing to termin, i have to reflash zeus?
Sent from my C1505 using XDA Premium 4 mobile app

MatsPunt said:
My dear fella. If you had read the thread I made you would know this!
This is the last time I will be saying this:
This is an update of jjm34 for the E dual. Version 1.1.0. Somehow on this version GSM isn't buggy. It is the E dual version, so you will have to select SIM1 as your SIM. The bugs are still the same:
-Video recording not working
-Video streaming not working
-Bluetooth not working(well, it turns on and connects but fails to exchange any media)
-Magnetometer not working(no automatic moving to landscape/portrait.
All right? Clear enough?
This ROM fixes just the GSM and nothing more. It was not made by me or UltraGamerHD. It is an update by jjm34.
Mats
Click to expand...
Click to collapse
and it has hsr0 dual recovery right?

Grimlock007 said:
and it has hsr0 dual recovery right?
Click to expand...
Click to collapse
Yep

SmashMii said:
What gets overwritten? I dont exactly understand, please explain to me. What i understand is i can flash cm10 on zeus, but when changing to termin, i have to reflash zeus?
Sent from my C1505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
once you flash cm10 zeus kernel gets overwritten with hsr0 dual recovery 1.3ghz oc kernel(made specially for cm10) .....which may cause gsm crash on termin/stock rom

UltraGamerHD said:
Required:
-Zues Kernel V3.1
Lets Begin:[/SIZE]
Click to expand...
Click to collapse
1. Zeus is spelled wrong.
2. [SIZE] tag is missing
And thanks for the guide!

Before this, i have problem on CM10, Xperia E Dual.
Cannot charge phone, no LED charging.
After flash stock ROM, there is no problem.
So i try this ROM, luckly, there is no problem.
Thanks for a guide!
Keep it up! Hope have 4.2.2 on Xperia E Dual same like this ROM :good:
P/s : sorry my spelling bad :crying:

meiax93 said:
Before this, i have problem on CM10, Xperia E Dual.
Cannot charge phone, no LED charging.
After flash stock ROM, there is no problem.
So i try this ROM, luckly, there is no problem.
Thanks for a guide!
Keep it up! Hope have 4.2.2 on Xperia E Dual same like this ROM :good:
P/s : sorry my spelling bad :crying:
Click to expand...
Click to collapse
no more updates for E.... cm11 under development

cm10 help needed
UltraGamerHD said:
Ultimate CM10 Install Guide​
Required:
-CM10 Zip (Odexed or Deodexed)
-Unlocked Bootloader
-Flashtool
-11.3.A.2.23 FTF (Single Sim Only)
11.3.A.2.1 FTF (Dual Sim Only)
-USB Cable
-Time
-Patience
-Zues Kernel V3.1
Lets Begin:[/SIZE]
1. Follow this guide to Unlock/Check if Your Bootloader Is Unlockable: http://unlockbootloader.sonymobile.com/
2. Install Flashtool.
3. Install Drivers which are in: C:\Flashtool\drivers\Flashtool-drivers.exe, run the program and install Flashmode and Fastboot Drivers.
4. Move the 11.3.A.2.23 FTF or the 11.3.A.2.1 FTF is your Xperia E is Dual Sim to C:\Flashtool\firmwares folder.
5. Run Flashtool, Click On the Lightning Bolt --> Select Flashmode and Select the 11.3.A.2.23 FTF or 11.3.A.2.1 if your phone is dual sim. and hit OK.
6. It will ask you to put the dervice in Flashmode, (PAY ATTENTION):
Power Down The Device,
Plug One end of the USB Cable into the USB Slot on the PC/Laptop,
Now Press the Volume Down Button and Plug the USB Cable In,
The computer an will recognise your phone and Flashtool (There will be a green led on your phone) will give an error resulting in it saying Install Drivers --> THIS IS OK!
Windows Will Now be installing drivers, let that finish then proceed.
7. Now Unplug the Cable, and do Step 6 and this time it will begin to Flash the FTF.
8. Once its done unplug your phone and this time plug it in while holding the Volume Up Button. (Blue Led)
9. Wait For Windows To Install Drivers then proceed.
10. Click the lightning bolt and this time select FastBoot Mode then select Select Kernel To Flash, in the right hand corner change .sin to .elf and go into the folder where you download Zues V3.1.elf and select it and it will Flash.
11. Once Finished Setup Your Phone Normally.
12. Copy the CM10 Zip to Your SD Card.
13. Power off your phone, power one while tapping the volume up or down button when you see the blue light.
14. Now use the Volume Buttons To Navigate To Wipe Data/Factory Reset and Hit Yes.
15. Now Select Install Zip From SD Card and Flash the CM10 Zip File.
16. Reboot and Enjoy Your CM10.
Download Links:
Flashtool: http://www.flashtool.net
Zues Kernel V3.1: http://forum.xda-developers.com/xperia-j-e/development/e-recovery-stock-11-3-2-23-t2658801
CM10 Zip (Odexed or Deodexed): http://forum.xda-developers.com/xperia-j-e/general/tip-fix-unknown-baseband-issueno-sim-t2674849
11.3.A.2.23 For Single Sim FTF: http://www.mediafire.com/download/3fmmkbmlqtjd6cy/Xperia+E+(C1505)_11.3.A.2.23_Unbranded.ftf
11.3.A.2.1 For Dual Sim FTF: http://www.4shared.com/file/55QLW02n/113A21.html
Click to expand...
Click to collapse
i want to go back to stock rom...how to do .. i have c1505 stock rom should i flash by flash tool
---------- Post added at 02:56 AM ---------- Previous post was at 02:54 AM ----------
meiax93 said:
Before this, i have problem on CM10, Xperia E Dual.
Cannot charge phone, no LED charging.
After flash stock ROM, there is no problem.
So i try this ROM, luckly, there is no problem.
Thanks for a guide!
Keep it up! Hope have 4.2.2 on Xperia E Dual same like this ROM :good:
P/s : sorry my spelling bad :crying:
Click to expand...
Click to collapse
i have same prob now bro how did u flash .. i mean u directly flash ur rom with flashtool ???? i have stock rom if i do will my phone will back to normal ???

Rajat22 said:
i want to go back to stock rom...how to do .. i have c1505 stock rom should i flash by flash tool
---------- Post added at 02:56 AM ---------- Previous post was at 02:54 AM ----------
i have same prob now bro how did u flash .. i mean u directly flash ur rom with flashtool ???? i have stock rom if i do will my phone will back to normal ???
Click to expand...
Click to collapse
Flash the FTF file from flashtool.
In flashtool, click the thunder icon, select flashmode, choose the FTF file, and select flash.
Now Wait.
Flashtool will prompt u to connect device in flashmode. Shut down your device, hold the down volume key and connect to pc.
You're done.
Next time, please don't quote op
Sent from my C1605 using XDA Premium 4 mobile app

cm10 help needed
sohailferdous said:
Flash the FTF file from flashtool.
In flashtool, click the thunder icon, select flashmode, choose the FTF file, and select flash.
Now Wait.
Flashtool will prompt u to connect device in flashmode. Shut down your device, hold the down volume key and connect to pc.
You're done.
Next time, please don't quote op
Sent from my C1605 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
last question ... will it back my phone to normal ??? and what about my recovry will it delet ??? if it delet will i have to flash my kernel to cwm ?? now i have twrp

Rajat22 said:
last question ... will it back my phone to normal ??? and what about my recovry will it delet ??? if it delet will i have to flash my kernel to cwm ?? now i have twrp
Click to expand...
Click to collapse
If you flash the FTF (firmware) file, you're phone will become absolutely normal. Like a factory release. It shall become ordinary, like the very first time when you bought it.
No, the recoveries wont last, you will have to flash the kernels again.
Sent from my C1605 using XDA Premium 4 mobile app

cyanogen
sohailferdous said:
If you flash the FTF (firmware) file, you're phone will become absolutely normal. Like a factory release. It shall become ordinary, like the very first time when you bought it.
No, the recoveries wont last, you will have to flash the kernels again.
Sent from my C1605 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
thank you so much.. i will leave this cm10 its worest.. no sim detec.. no battery charge... i will flash it with stock rom

(Root) pre rooted flashable zip file 18.3.C.0.39 for D2303

Hey there,
i have created a flashable zip file for the xperia M2 D2303 with this tool: http://forum.xda-developers.com/crossdevice-dev/sony/tool-prfcreator-easily-create-pre-t2859904
You can flash this file in CWM Recovery like this: http://forum.xda-developers.com/showthread.php?t=2746407
After flashing you have the newest firmware for this device with root rights!
Good luck and happy flashing!
Instructions:
1. Unlock your bootloader if not already done
2. Download CWM Recovery from link above
3. Flash the CWM with flashtool in fastboot mode
4. Reboot in CWM
5. Wipe data/factory reset, wipe cache, wipe dalvik
Note: If you want not loose your apps and settings only wipe cache and dalvik in CWM before flashing the zip file.
6. flash the zip file from link below
7. reboot system
8. done
If the system after the flash is not writable, please visit this thread:http://forum.xda-developers.com/xperia-m2/development/tut-fix-mount-kitkat-root-t2861661
requirements:
Sony Xperia M2 D2303
Unlocked bootloader
CWM Recovery from link above
Flashtool
Note: Please backup your system in CWM befor flashing!
Credits:zxz0O0 for PRFcreator, DooMloRD for CWM, Naufal Sidik for fix mount system
--------------------------------------------------------------------------------------------------------------------------------------------------
Download: https://mega.co.nz/#!C9gGyBRY!flV_DeYVVLxBrm69qr_PrAUVp7TasoykszvA-5r7Gq0

What's the difference between this version and 18.3.C.0.37 except root? Also how to flash cwm?

Now we just need a method to bring CWM or TRWP to the D2303. Or is it included in the above, and I can flash it via kernel + Flashtool?

I will update the op as soon as posible.
Sent from my D2303 using XDA Premium 4 mobile app

If the kernel contains CWM, I could extract the kernel.elf from the .zip, then flash it via fastboot. Correct?
Which region is the ROM from?

peter-k said:
If the kernel contains CWM, I could extract the kernel.elf from the .zip, then flash it via fastboot. Correct?
Which region is the ROM from?
Click to expand...
Click to collapse
The kernel in this zip file not includes CWM! You need the CWM from DooMloRD.
Flash this file via fastboot, then reboot in recovery.
This is the customized MY 1281-1590 version of this firmware.

dotzi75 said:
The kernel in this zip file not includes CWM! You need the CWM from DooMloRD.
Flash this file via fastboot, then reboot in recovery.
This is the customized MY 1281-1590 version of this firmware.
Click to expand...
Click to collapse
Great. I am going ahead.
Not - Doomlords Recovery link doesn't work ... at least not here in China.

qtoo941 said:
What's the difference between this version and 18.3.C.0.37 except root? Also how to flash cwm?
Click to expand...
Click to collapse
The differences are minimal, minor bugfixes. On my device it works fine.
For flash the CWM, read the op.

when will their be a custom kernel for us locked bootloaders with cwm on it .as would like to see it on the m2 locked bootloaders .

If the fix mount system tut here does not work for you, which may not, here is a simple fix just for removing the unneeded system apk's after flashing dotzi's 18.3.C.0.39:
- create a file named "enable" with a file editor with the value 0 in it
- save the file without .txt extension, or remove the extension after the file is saved
- copy the file "enable" to sys/kernel/security/sony_ric (ignore any failed operation message)
- set permissions to rw-r-r-
Gives full access to all system files for the current session.
---------- Post added at 12:33 PM ---------- Previous post was at 12:24 PM ----------
This customized ROM works fine for me. Thanks to the OP!
Perfect would be CWM integrated into kernel, dito for the mount-sript (and init support) into ROM. That's all we need No de-odexing or other pointless stuff.

This customized ROM works fine for me. Thanks to the OP!
Perfect would be CWM integrated into kernel, dito for the mount-sript (and init support) into ROM. That's all we need No de-odexing or other pointless stuff.
Click to expand...
Click to collapse
Nice to hear that it works. To integrate CWM will only be possible if a working Recovery is available for the D2303. I just tried it in the kernel building, but I failed miserably. But I will try as soon as possible to integrate the mount-script and the init.d support.
Let us hope that even more people to deal with it and the development is of overriding driven.

dotzi75 said:
Nice to hear that it works. To integrate CWM will only be possible if a working Recovery is available for the D2303. I just tried it in the kernel building, but I failed miserably. But I will try as soon as possible to integrate the mount-script and the init.d support.
Let us hope that even more people to deal with it and the development is of overriding driven.
Click to expand...
Click to collapse
Consider putting the doomlord kernel which contains the CWM onto another storage (if he allows). Downloading from the current location is really not fun.
I'll be subscribing here as it seems you want to bring it further.:good:

Wow, nice one
Thanks for your hard work, really appreciate it
(Currently waiting for the dual-SIM one xD)

How do you were able to install CWM ? Your link is linket do DooMLoRD's CWM für JB for the D2305.
I'm gedtting a bootloop by installing it.

so far this is working i flashed cwmon my D2303 and im waiting for it to boot up now lol on the wave screen
Edit: WORKS amazing thank you so much rooted on 4.4.2 i love you (no homo)

hero66 said:
How do you were able to install CWM ? Your link is linket do DooMLoRD's CWM für JB for the D2305.
I'm gedtting a bootloop by installing it.
Click to expand...
Click to collapse
It doesn't matter. Flash the cwm via fastboot, and boot only in recovery by pressing vol down. Then Flash the zip file and reboot! It works, believe me!
Sent from my D2303 using XDA Premium 4 mobile app

hero66 said:
How do you were able to install CWM ? Your link is linket do DooMLoRD's CWM für JB for the D2305.
I'm gedtting a bootloop by installing it.
Click to expand...
Click to collapse
Enter CWM, don't allow fully loading bootloader.
---------- Post added at 10:21 AM ---------- Previous post was at 10:17 AM ----------
For mounting system permanent use the latest version Busybox Installer, previous version will not work. Then use Init.d Toggle (both Play store).

Thanks, finaly my M2 KK is rooted.

Any chance for something to d2306? Or can we crossflash the d2303 one?
Sent from my D2306 using XDA Free mobile app

macabrocabral said:
Any chance for something to d2306? Or can we crossflash the d2303 one?
Sent from my D2306 using XDA Free mobile app
Click to expand...
Click to collapse
I will take a look at this next few days if i have time. I'm busy in my Job now. Keep calm, development is just in the beginning! Don't crossflash, i don't know if its work!
Sent from my D2303 using XDA Premium 4 mobile app