I've seen quite a few posts of people with freezing after installing 4.4.2 no matter what they do and both myself and a friend have been at the mercy of this - myself with a custom rom and my friend with the Samsung OTA update.
From what I remember from back in the HD2 days with similar symptoms it's related to the baseband/modem - a check of both her phone and mine showed the baseband was incorrect for the ROM and updating it resolved the issue.
The following guide will flash the latest stock, unrooted, NB4 ROM with a matching modem/baseband.
Whilst it shouldn't affect Knox as everything is official signed files (and Knox is fine on my friends phone after I did this procedure), I take no responsibility for your own Knox status.
***THIS *SHOULDN'T* AFFECT KNOX IN ANY WAY AS YOU ARE ONLY FLASHING SIGNED STOCK SAMSUNG STUFF***
First off, backup anything on the phone you want to keep and download the following then extract them all to the same folder:
Samsung USB Drivers - http://developer.samsung.com/android...er-for-Windows
Odin - http://uploaded.net/file/hwtdrpll
Latest 4.4.2 Firmware - https://mega.co.nz/#!QVwlVDgJ!QyAxmD...TVvdM07LOs0V10
PIT File for 4.4.2 Firmware - http://forum.xda-developers.com/show...9&postcount=77
NB1 Modem Firmware - https://mega.co.nz/#!JJBglRDY!ZT5SkT...4obRSKpB4B8NB1
1) Install Samsung Drivers
2) On your phone go Settings --> General --> About and keep tapping "Build Number" until it says developer mode enabled.
3) Go back to Settings --> General and tap Developer Options.
4) Tick enable "USB Debugging" then plug the phone into your computer.
5) Push and hold Volume Down + Home Button + Power Button all at the same time - hold until it goes black and vibrates indicating it
rebooted. Once it vibrates, release the power button but keep the other two held down - when you get the prompt on the screen press Volume Up - this will put the phone into Odin mode.
6) On the computer, right click Odin and click "Run as Administrator"
7) Click the button labelled PIT and select the file "My_N9005.pit"
8) Click the button labelled AP and select the file labelled "N9005XXUENB4_N9005DBTENB1_N9005XXUENB1_HOME.tar.m d5"
9) Make sure Re-Partition is ticked and click start.
10) When it finishes your phone will reboot - once you see the Samsung Logo, put the phone back into Odin Mode by pushing and holding Volume Down + Home Button + Power Button again, same as last time. Don't close Odin just yet.
12) In Odin, click Reset and then click the button labelled AP and select the file called "N9005XXUENB3_Modem-XXUENB1-LTE.tar.md5"
13) Click Start
14) When it finishes it should reboot. Dont panic about your phone appearing german, you can change the language right at the start on the first screen
***Optional Steps***
If your phone doesn't boot still, do the following:
1) Hold down Volume Up + Home Button + Power until it reboots, then release the power button keeping the other two held down (Basically the same as Odin mode except Volume Up instead of Volume Down).
2) You should now be in recovery - ignore any errors. Select Wipe Data/Factory Reset then Wipe Cache Partition - you don't need to reboot in between.
3) Once that's done, reboot and you should be up and running fine. If it still hasn't booted after 10 mins at this point, it's the phone itself most likely.
hi what is the password for download.. mega is asking for decryption key...
Related
I felt many users are facing problems to upgrade with official stock rom DDKP3 So here is the guide.If it helps you DON NOT FORGET TO HIT "THANKS"
============================================================
1- Download I9003 DDKL3 2.3.6 Gingerbread package from link given below Or from sammobile.com to your computer. After this you need to extract the same in your computer.
http://hotfile.com/dl/145754643/7803526/I9003DDKP3_I9003ODDKPI_INU.rar.html
2- Now you will have to enable the USB Debugging from the path “Settings > Applications > Development > USB debugging. Ensure that the USB Debugging option is ticked
3-turn Off the phone so that I9003 can be entered in the Download Mode. The Download mode mode can be entered by pressing Volume Down Key + OK button, and holding both simultaneously press the Power Button.
4-Once the device is entered in the Download Mode, connect the phone to the computer while keeping the Odin opened in your computer. After automatic driver installation process, ID:COM section in Odin will turn yellow indicating that you are now ready to proceed to the next step.
5-Now in Odin, click on “PDA” and select “I9003DDKP3_I9003ODDKPI_I9003DDKP4_HOME.tar.md5”. And click START
-Please note that once the firmware is updated successfully, phone will be rebooting. It will take around 5 minutes for the phone to get applied this firmware.
6-Disconnect the phone from computer and let it be ON.and then you need to turn off the phone and go to recovery mode by pressing CENTER,VOLUME UP and ON/OFF Button.
7-Once you enter into the recovery mode, choose the options Wipe data/factory reset and also you need to select Wipe Cache partition and then reboot your device by selecting reboot system now option.
Thats all you have updated your mobile to latest official firmware DDKP3.
Disclaimer: I should not be held responsible in any manner just in case if anything happens to your device which is very unlikely if you follow all the mentioned instructions properly.
In case of any doubt let me know i will try to clear same
this is a history now!
there was no need to post this!
Genius !!!
delete the post :!
Already guides on this. Thank you for the effort though.
Hello,
I have tried many many system in my tablet and there is nothing working on with me i need someone who can help me to get the tablet back to default system i have tried cyanogenmod all version my tablet is p6200 and i tried everything now its not working anymore , i need some steps to get it back guys
if you want to go stock rom use Odin and download stock rom for you're country from http://www.sammobile.com/firmware/?page=3&model=GT-P6200&pcode=0&os=1&type=3#firmware
when i connect the usb in laptop its shown
USB Device Not Recolonize what shall i do to get the tablet to default and i have tried many things like i root the tablet and i try manyyyyyy roms so please can you tell me what to do exactly i download the kies program in my laptop what i have to do else ?
Not kies but use Odin and put you're tablet in download mode (power + vol down)
explain please give me the link of odin because i dont know it and when i press in power and volume up its shown
Warning
A custom OS can cause critical problems in tablet and installed applications. if you want to download a custom OS, press the voume up key.
otherwise, press the volume down key to cancel
Volume up : Continue
Volume down: Cancel ( restart tablet )
i downloaded odin3 v.1.85 how can i use it to do the Firmwares i extract the files i got 5 files inside them
GT-P6200-MULTI-CSC-OXXLB1_RST.tar.md5
MODEM_P6200XXKL7_REV_04_CL1088622.tar.md5
P6200_APBOOT_P6200XXLB1_CL629097_REV02_user_low_ship.tar.md5
P6200_CODE_P6200XXLB1_CL629097_REV02_user_low_ship_16G.tar.md5
px_20111010_3G_16G.pit
How can i use the files on the program what the steps ?
NightZeus said:
i downloaded odin3 v.1.85 how can i use it to do the Firmwares i extract the files i got 5 files inside them
GT-P6200-MULTI-CSC-OXXLB1_RST.tar.md5
MODEM_P6200XXKL7_REV_04_CL1088622.tar.md5
P6200_APBOOT_P6200XXLB1_CL629097_REV02_user_low_ship.tar.md5
P6200_CODE_P6200XXLB1_CL629097_REV02_user_low_ship_16G.tar.md5
px_20111010_3G_16G.pit
How can i use the files on the program what the steps ?
Click to expand...
Click to collapse
What To Do:
- Make sure Kies is Closed
- Disconnect the Tab from your PC
- Restart your Tab in Download Mode (Power Off Tab then Hold Volume - & Power Button)
- Open Odin , do not change any checkbox items
- Click the PDA button and find the Stock ROM .md5 file and select it (DO NOT HIT START YET)
- Plug in your Tab to the PC at which point the first "ID:COM" box should turn yellow and the Message windows should read "Added"
- Now, Hit Start
- When Completed the "ID:COM" Box should turn Green and right above it it should say "Pass"
The tablet should reboot,
- Disconnect the Tab from your PC
How can i go to download mode if i press on power and volume - its turn to recovery mode how can i go to download mode now
I find how to go to download mode
i open the odin and put the file on PDA and i saw its became yellow and added fine and then i hit start
its not sucess i got faild
what can i do now
try to find a tar.md5 package with a .pit file specifically for your device..,
alternately try flashing a stock Honeycomb ROM.. and booting into recovery and factory reset.
Most importantly research and read, If you can get into Download mode you're 90%+ will be OK
Get ClockworkMod recovery from here
http://forum.xda-developers.com/showthread.php?t=2112667
Use odin to flash it
boot to recovery
wipe system and cache
use odin to install your stock rom again
boot
Hi guys,
I just wanted to share you my Quick and Easy guide on how to fix the "Stuck in Simple Recovery" for CyanogenMod ROMs. I had this just once, a few weeks ago and important data was on my phone that I didn't want be lost. So let's get to it:
1. Take out the battery to make sure Phone is COMPLETELY turned off. (Or just turn it off, just to make sure...)
2. Insert battery. Then hold Volume Down button (not volume up), Home Button and Power Button at the same time.
3. It will say "Downloading" or "Download Mode". Connect your Phone using USB to PC and open up Odin (Download here)
(If it does not show up, Download drivers here)
4. Click on the AP tab on Odin v3.10, and click on the CWM zip file (Select version and Download here)
5. It will reboot (or give an option to reboot).
6. Done! :laugh:
If this helped you, hit Thanks
Oh and Questions may be asked
I am using the Samsung galaxy A7 2016 edition and the phone has gone through a couple of drops. Whenever I dropped the phone, the GPS seems to stop working properly and won't fix on a satellite. When I factory reset my phone, it works properly again. I've dropped my phone again and the GPS isn't working again. Is there any other way other than factory reseting my phone that can fix this? My phone isn't rooted.
Dhanussh said:
I am using the Samsung galaxy A7 2016 edition and the phone has gone through a couple of drops. Whenever I dropped the phone, the GPS seems to stop working properly and won't fix on a satellite. When I factory reset my phone, it works properly again. I've dropped my phone again and the GPS isn't working again. Is there any other way other than factory reseting my phone that can fix this? My phone isn't rooted.
Click to expand...
Click to collapse
Hello
There is and other manner to factory reset the phone do this:
1. Go to SamMobile
2. Search you exact model number
3.Extract (unzip) the firmware file
4.Download Odin v3.13.1
5.Extract Odin ZIP file
6.Open Odin v3.13.1
7.Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
8.Connect phone and wait until you get a blue sign in Odin
9.Add the firmware file to AP / PDA
10.Make sure re-partition is NOT ticked
11.Click the start button, sit back and wait few minutes
12. When the green button is showing disconnect the phone.
13. If the phone doesn´t starts in 5-10 min power off and press and hold Home + Power + Volume up buttons and in the recovery select the wipe data factory reset option and reboot.
DISCLAIMER This is a procedure that you have to follow by your own risk I don´t be the responsible of any wrong thing on this procedure and it´s derivates.
I hope that I help you
Regards
elmakina said:
Hello
There is and other manner to factory reset the phone do this:
1. Go to SamMobile
2. Search you exact model number
3.Extract (unzip) the firmware file
4.Download Odin v3.13.1
5.Extract Odin ZIP file
6.Open Odin v3.13.1
7.Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
8.Connect phone and wait until you get a blue sign in Odin
9.Add the firmware file to AP / PDA
10.Make sure re-partition is NOT ticked
11.Click the start button, sit back and wait few minutes
12. When the green button is showing disconnect the phone.
13. If the phone doesn´t starts in 5-10 min power off and press and hold Home + Power + Volume up buttons and in the recovery select the wipe data factory reset option and reboot.
DISCLAIMER This is a procedure that you have to follow by your own risk I don´t be the responsible of any wrong thing on this procedure and it´s derivates.
I hope that I help you
Regards
Click to expand...
Click to collapse
So you're saying that this method will need my phone to factory reset too but i won't have the same problem in future?
Dhanussh said:
So you're saying that this method will need my phone to factory reset too but i won't have the same problem in future?
Click to expand...
Click to collapse
Hello
Yes you shouldn,t have this problem in the future. If this occurs again you have to fix hardware GPS antenna.
Sorry for the delay
Best Regards
Hey guys, I know that most have doubts on rooting Samsung f41 . let's go step by step
This method does not brick your phone [Fully Tested] the only thing is you have to follow all steps properly
1. go to developer settings ( to enable it go to About phone software information tap the build number 5 to 7 times ) activate "allow oem unlock", and turn off the device, connect it to the computer with a cable, and, as soon as you plug in the cable, press volume + and volume - at the same time, then, press and hold volume +, after this, just press one time the volume up button to confirm, the bootloader will be unlocked and the device reset, as soon as the screen "erasing" disappears.
2. Now go to download mode for that power of your phone and press vol up and vol down at the same time and plugin your charger wire which is connected to your pc and that's all
3. make sure your computer recognized your device in download mode, go to odin, go to "AP", and select the root file according to your android version, press "start", and it's done! just install magisk apk and let the app do the additional configuration
NOTE - every time when you turn on your device, a black screen will appear saying that the software is not official from samsung, just press power, it's normal.
on oneui 2/2.5, the root is a little bit unstable, but on oneui 3 it's solved, I recommend OneUi 3 for being more stable and updated.
Required Files for this method
1. Odin - https://odindownload.com/download/Odin3_v3.14.1.zip
2. Samsung usb drivers - https://download2330.mediafire.com/...f1rn/SAMSUNG_USB_Driver_for_Mobile_Phones.exe
3. Root file Android 11 - https://mega.nz/file/yzhmDJjS#afLu8KhCzWhFXyovK5Dpl1WQdbt6evMCV5u4GPRMGRE
Android 10 - https://mega.nz/file/iqxQ0ZZZ#fT_dZzvPW-c274ELyDocTEIEl_cROJWxpseAtbfgypI
Did something wrong in this and it resulted your phone getting stuck on Download mode Here's a fix
[FIX] [HOW TO FIX Samsung PHONES STUCK ON DOWNLOAD MODE] WITHOUT DATA LOSS
Hi guys many of you would have tried to install stock rom root your phone etc and it didn't go well and resulted your phone getting stuck on download mode here's a solution PRE - REQUSITES 1. ODIN -...
forum.xda-developers.com