lm still in the official o2 rom wm5, but last week, l hv try to install a file "Xda_Exec_Upgrade_v1.30.162" through my computer (window 7), when i installing the file , l saw my xda exec's screen is freeze!!!!! so l just unplug the usb cable from my computer, and soft reset my xda exec, but a worse thing happen. when it start loading, it freeze at the o2 screen with 3 line word at right down corner - ( R 1.09.00 ) , ( G 42.42.P8 ) , ( D 1.30.107 WWE ). And so strange, when l charge my exec there is no light showing, when l remove the battery the light is showing red. l hv put my battery to my friend exec it work!!!
so please help!!!!
1. screen keep freeze at o2 screen???????????
2. when remove battery, and then put it back and charge, the o2 screen come out immediately. without touch any button????? and no charging light showing.
3. only showing red light when remove the battery????
sorry for the poor english
please help.............
try hard resetting by pressing the reset and power button together for a minute, then if it works a screen will appear that says ''press call and call end button together''
do it, see if problem is solved. that method has worked sometimes for me but u will lose all ur data, applications installed.
Related
:shock: Gasp, a problem with my MDA! :shock:
Hello everyone, I was holding my mda in my hand today, and suddenly the phone beeped, and then turned off. This sounded like a submarine sonar. Anyways, when I turn it back on now it will go to the t mobile screen ( boot screen ) load up the first 4 lines of red characters, and then hang. It will not do anything, and eventually it will beep. It does this regardles of power source (wall/battery). The four lines that it loads are :
ipl 1.08
spl 1.08
gsm 01.09.01
OS 1.8.10.2
After these load the windows loading icon that spins appears in the middle of the screen and the system makes the same sonar booey sound. MY MDA WILL NOT TURN ON!!!!!!!!!!! Thanks in advance for all the help, does anyone know how to fix this?
David Sondergaard
Poor man!! but hehe... your savor is here!!!
you need to press the Camera button then press reset (DON"T RELEASE THE BUTTON UNTIL THE 3 COLOR STRIPS COME OUT) --> ALready enter USB mode, from here you can flash your ROM (Recomended with Oringinal ROM)...
I have exactly the same problem and it work on mine...
Good luck man!
pls see this link. http://forum.xda-developers.com/showthread.php?t=250709
if you have further question email me: [email protected]
HI!
I wanted to upgrade my M600 to AKU 2.2 with 8mb page pool. So I have made rom with 8mb page pool with tutorial on wizards wiki page translate it back to nk.nbf and wanted to upgrade it with RUU...but it stopped by 2% and showed an error. after that my phone turned off and when i want to tunrn it on again it shows RGB screen for about 3 seconds and turns off, if i want to turn it on again
i must take out battery for about 2 minutes, then insert it in and it happens again for about 3 seconds. If i plug in usb while its on it turns off.
Did i bricked it? if not, please help.
Thank you!
no you didn't brick it, try and enter the bootloader (hold down the camera button and reset) from there run any offical ROM.
if you phone switches off after you are in the bootloader, you battery is probably empty, only way to fix this is to connect to wires from your charger directly to your phone on pins 1 and 5 and then flash it.
Is it well if i just plug it on wallcharger? Or it must be just two wires on 1st and 5th pin? The Orange LED isnt on when its on charger and when I hold down camera and reset button the phone dosent react at all.
OK! I got into boot loader by connecting wires directly to battery pins and now reflashing.
try my 2.2 rom if you intrested in it after reading teh changes, 6mb with patches to 4mb 8mb 12mb page pool size
hope you like after fixing you phone, and if you can't try RUU_Prophet_220734_2207114_024721_NVID this rom
@paradis_pal: I've tried your rom before i bricked my M600. When i wated to upgrade your rom, it stucked at 85% and then error. It did the same on next 2 tries. So i took the same AKU 2.2, and tried to change pagepool size and i made a mistake somewere, and temporarly bricked my phone. It's working now, thanks to Jesterz. But still please fix your rom, i would like to test it.
I did fix it
it may I exceed the limit of free speace in the ROM, so I UPXed dr_yar_bluetooth.exe, but I swear the old one worked with me
and now it is working with me with Both pdocwrite and nk.nbf hope you like it
HELP
zgi said:
OK! I got into boot loader by connecting wires directly to battery pins and now reflashing.
Click to expand...
Click to collapse
hEY BUDDY HOW DID U DOTHIS !!
M having the same errr.
the prophet does not respond to the wall charger at all.My Neo all of a sudden went blank since yesterday.It so happened..
I wanted to make a call, I removed my NEO from POCKET and It just showed the GREEN LED BLINKKING the POWER button dint responded at all..
I reset the NEO and now its not showing any thing
Does not respond to the wall charger nor any LED only thing happen is the phone gets heated on Charging(as usual as it did earlier)
Do U know that trick of stripping the wall charger and than short the pins ...
Which is the 1st Pin from bottom or from top..
ANY OTHER ADVICE
Hi,
I have a problem, feew days ago i upgrade my xda exec to new rom, i dont remember version, i delete installer.
Everything was gread, upgrade went smoothly.
Yesterday i'm playing music on my xda (WM Player ) and everything went down, i power up xda and it stand on Load screen O2.
I'm try to remove battery, try to format device pressing RESET and this two MINUS keys on top keyboard, its resseting to defaults try to reboot and still wait on o2 screen.
I don't have any idea what should i do.
I'm try to load this rom :
UNI 5.2.20931 G3/G4 FINAL VERSION by VNInt /w WinXP theme
but active sync don't recignize my device on this boot load screen.
The installer's says put device off usb cable, put reset and hold 2 minus keys, and this should show SERIAL : USB something like that, and then upgrade. But after when i press that, im getting reset factory defaults, not this about connection by USB or Serial.
zoom for instaled version:
and finally
why when i press reset and two minus keys im getting this:
i want to load this USB Cable sync white screen ?
Solved.
Press light, power and reset.
Then you go usb connection screen.
Close thread please
Dear Mods
This thread can be closed
Best,
Hello, I have a PDA Eten glofiish M810, and I have a problem now will explain it to what is
success. While performing a ROM upgrade a few days ago, the update
that fails and the PDA connected to your PC, turn off the display (display neroooo).
I try to restart it, removing battery but nothing, the buttons light up
normally but display BLACK. What the hell happened?
So I do try as hard reset, power + soft reset (anything), power + soft
reset + cam (nothing) etc etc. .... but I feel lots of hard reset the PDA is restarted
(I notice the buttons that will go off) but the display is always black. Provo
directly to install a ROM Journal (ps. when I connect the PDA to the PC, the
PC sees me quietly MS Active Sync works normally) but the bar
Progressive does not go forward remains at 0%, nothing!
I followed instructions .... Power + rec (no red button on the camera) and then go with
the pen .... for many seconds? 1 made 5 made 10 made 1 minutes did take off .....
the stylus, Dividend fingers .... NOTHING! but a screen comes out .... kind of testing
normalemte touchabile (1 for CPU, RAM 2 ....) but it is a screen type under
screen "in the sense that it is difficult to see it ... in fact I could normally
viewed over a light projected on the screen .... trying and trying again
(power-rec and stylus) screen testing no longer appears but the logo now appears
Glofish (always under the screen and view it through projected light) ... but after
ten seconds disappears ...
I upgraded directly from SD. but the result is always the same.
I know some of you help?
HELP MEEEEEEEEEEEEEEEEEEEEEEEEE pleaseeeeeeeeeeeeeeeeee !!!!!!!!!!!!!!!!!
marco221186 said:
Hello, I have a PDA Eten glofiish M810, and I have a problem now will explain it to what is
success. While performing a ROM upgrade a few days ago, the update
that fails and the PDA connected to your PC, turn off the display (display neroooo).
I try to restart it, removing battery but nothing, the buttons light up
normally but display BLACK. What the hell happened?
So I do try as hard reset, power + soft reset (anything), power + soft
reset + cam (nothing) etc etc. .... but I feel lots of hard reset the PDA is restarted
(I notice the buttons that will go off) but the display is always black. Provo
directly to install a ROM Journal (ps. when I connect the PDA to the PC, the
PC sees me quietly MS Active Sync works normally) but the bar
Progressive does not go forward remains at 0%, nothing!
I followed instructions .... Power + rec (no red button on the camera) and then go with
the pen .... for many seconds? 1 made 5 made 10 made 1 minutes did take off .....
the stylus, Dividend fingers .... NOTHING! but a screen comes out .... kind of testing
normalemte touchabile (1 for CPU, RAM 2 ....) but it is a screen type under
screen "in the sense that it is difficult to see it ... in fact I could normally
viewed over a light projected on the screen .... trying and trying again
(power-rec and stylus) screen testing no longer appears but the logo now appears
Glofish (always under the screen and view it through projected light) ... but after
ten seconds disappears ...
I upgraded directly from SD. but the result is always the same.
I know some of you help?
HELP MEEEEEEEEEEEEEEEEEEEEEEEEE pleaseeeeeeeeeeeeeeeeee !!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Hi am very sorry about ur device but am sure it can be fixed I dont own a device like that I have a HTC prophet but you have to post this question in the same place you read about upgrading your device am sure they have recovery steps can u post the link were u got the files and instructions to update ur device? thanks al look into it and see if there is a solution or not but you should try to hardspl your device and flash again but if ur pc cant find the device try this go to active sync settings and uncheck allow usb connections the pc should find the device also try to download the original rom for your device you can find it at the manufacture site in the download section try flashing it to your device it should help.
if not let me know and plz post the link you got everything from ok
marco221186 said:
Hello, I have a PDA Eten glofiish M810, and I have a problem now will explain it to what is
success. While performing a ROM upgrade a few days ago, the update
that fails and the PDA connected to your PC, turn off the display (display neroooo).
I try to restart it, removing battery but nothing, the buttons light up
normally but display BLACK. What the hell happened?
So I do try as hard reset, power + soft reset (anything), power + soft
reset + cam (nothing) etc etc. .... but I feel lots of hard reset the PDA is restarted
(I notice the buttons that will go off) but the display is always black. Provo
directly to install a ROM Journal (ps. when I connect the PDA to the PC, the
PC sees me quietly MS Active Sync works normally) but the bar
Progressive does not go forward remains at 0%, nothing!
I followed instructions .... Power + rec (no red button on the camera) and then go with
the pen .... for many seconds? 1 made 5 made 10 made 1 minutes did take off .....
the stylus, Dividend fingers .... NOTHING! but a screen comes out .... kind of testing
normalemte touchabile (1 for CPU, RAM 2 ....) but it is a screen type under
screen "in the sense that it is difficult to see it ... in fact I could normally
viewed over a light projected on the screen .... trying and trying again
(power-rec and stylus) screen testing no longer appears but the logo now appears
Glofish (always under the screen and view it through projected light) ... but after
ten seconds disappears ...
I upgraded directly from SD. but the result is always the same.
I know some of you help?
HELP MEEEEEEEEEEEEEEEEEEEEEEEEE pleaseeeeeeeeeeeeeeeeee !!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Perhaps here is the right place to look:
http://www.eten-users.eu/index.php?showforum=42
Good luck,
orb3000 said:
Perhaps here is the right place to look:
http://www.eten-users.eu/index.php?showforum=42
Good luck,
Click to expand...
Click to collapse
You can try the solution given here http://www.eten-users.eu/index.php?showtopic=19398 and see if it works for you am still looking for others but again I sugest you post your question there since the members there know more about you device then us and can help you much faster too good luck
http://www.eten-users.eu/index.php?showtopic=19074 has some good information aswell
Please help!
My HTC TP2 freezes at start up with a white screen and the HTC Logo and some details in red at the bottom:
B 80
R 4.49.25.17
G 61.44tc.25.32U
D 1.86.67102
No USB connection can be established.
What happened:
1. Tried to update from original WM 6.1 to WM 6.5 by using the official HTC ROM update utility. Seems like the phone was in pilot mode during the update. the updtae process was completed and i clicked finish. the device was to restart and the white screen problem started.
2. Restarted phone and multicolor screen appeared and stayed. After connecting with USB cable again "USB" appeared at the bottom but cannot connect to the activesync no more
3. Restarted again (by removing the battery and hit power button) and state reached like described above (HTC TP2 freezes at start up with the white screen and the HTC Logo and some details in red at the bottom).
4. Performed a hard reset but did not help.
What can I do to bring the phone back to life?