Have i bricked my SPV M600? - JAMin, XDA Neo, S200 Software Upgrading

HI!
I wanted to upgrade my M600 to AKU 2.2 with 8mb page pool. So I have made rom with 8mb page pool with tutorial on wizards wiki page translate it back to nk.nbf and wanted to upgrade it with RUU...but it stopped by 2% and showed an error. after that my phone turned off and when i want to tunrn it on again it shows RGB screen for about 3 seconds and turns off, if i want to turn it on again
i must take out battery for about 2 minutes, then insert it in and it happens again for about 3 seconds. If i plug in usb while its on it turns off.
Did i bricked it? if not, please help.
Thank you!

no you didn't brick it, try and enter the bootloader (hold down the camera button and reset) from there run any offical ROM.
if you phone switches off after you are in the bootloader, you battery is probably empty, only way to fix this is to connect to wires from your charger directly to your phone on pins 1 and 5 and then flash it.

Is it well if i just plug it on wallcharger? Or it must be just two wires on 1st and 5th pin? The Orange LED isnt on when its on charger and when I hold down camera and reset button the phone dosent react at all.

OK! I got into boot loader by connecting wires directly to battery pins and now reflashing.

try my 2.2 rom if you intrested in it after reading teh changes, 6mb with patches to 4mb 8mb 12mb page pool size
hope you like after fixing you phone, and if you can't try RUU_Prophet_220734_2207114_024721_NVID this rom

@paradis_pal: I've tried your rom before i bricked my M600. When i wated to upgrade your rom, it stucked at 85% and then error. It did the same on next 2 tries. So i took the same AKU 2.2, and tried to change pagepool size and i made a mistake somewere, and temporarly bricked my phone. It's working now, thanks to Jesterz. But still please fix your rom, i would like to test it.

I did fix it
it may I exceed the limit of free speace in the ROM, so I UPXed dr_yar_bluetooth.exe, but I swear the old one worked with me
and now it is working with me with Both pdocwrite and nk.nbf hope you like it

HELP
zgi said:
OK! I got into boot loader by connecting wires directly to battery pins and now reflashing.
Click to expand...
Click to collapse
hEY BUDDY HOW DID U DOTHIS !!
M having the same errr.
the prophet does not respond to the wall charger at all.My Neo all of a sudden went blank since yesterday.It so happened..
I wanted to make a call, I removed my NEO from POCKET and It just showed the GREEN LED BLINKKING the POWER button dint responded at all..
I reset the NEO and now its not showing any thing
Does not respond to the wall charger nor any LED only thing happen is the phone gets heated on Charging(as usual as it did earlier)
Do U know that trick of stripping the wall charger and than short the pins ...
Which is the 1st Pin from bottom or from top..
ANY OTHER ADVICE

Related

Almost bricked !! really ! help needed before it dies !!!

Bonjour
I upgraded to WM6 (pdaviet) 2 months ago (I guess..), and problems started to appear a few weeks ago. First it just was hard to boot sometimes, had to reboot several times to get it up and running, but when it could start everything was fine. Then since yesterday, it became harder. And today, couldn't start it at all. Tried several times, and everytime the screen went melted, corrupted, like if it couldn't stand an o/c, but it always runs at normal speeds. I guess it has something to do with the battery and the way WM6 handles it (or at least the implementation we have on our prophet).
I tried to hard-reset, I left it a long time on the format screen (before the actual HR) and it handled it for long enough, but the same thing started while setting up WM.... too bad !
While writing this message I tought I could try to downgrade, and I did using AKU3.3-Jester-b1.
I had no problem while the phone was in guest mode after the HR.
Everything went nice during first step upgrade, but on final reset it did the same thing, and now..... it cannot start at all !!!!
Someone has an idea ? I own a G4 and it has the following roms :
IPL 2.10, SPL 2.20, GSM 2.47 (or something like that)
It won't charge (but my batteries are full, I've got an external charger), it won't start from battery nor from power, even if the battery is removed.
Damn, at least I guess I can return it like that to orange, since it cannot start one can't see the modified rom...
If anyone has a suggestion, it is more than welcome ^^
Thanks !
Niko
huh !
back to semi-life ^^
After a few hours left alone without battery or sim card, it started again...
but it still resets every few minutes, or the screen goes melted (actually its like white scanlines that fulfill the screen).
I'll try to leave it shutdown for the night, see if I can at least put the orange splash screens and rom back for warranty purpose.
But it now has serious HW problems, for sure. And my opinion is WM6 has something to do with that. BEWARE !
Another strange thing is that I now have to keep the reset button pressed for half a second to reset, where it reseted instantly before. Those devices really have unstable hardware.
FYI, it was almost brand new, as it was warranty-replaced about one week before I installed WM6.
lastnikita said:
back to semi-life ^^
After a few hours left alone without battery or sim card, it started again...
but it still resets every few minutes, or the screen goes melted (actually its like white scanlines that fulfill the screen).
I'll try to leave it shutdown for the night, see if I can at least put the orange splash screens and rom back for warranty purpose.
But it now has serious HW problems, for sure. And my opinion is WM6 has something to do with that. BEWARE !
Another strange thing is that I now have to keep the reset button pressed for half a second to reset, where it reseted instantly before. Those devices really have unstable hardware.
FYI, it was almost brand new, as it was warranty-replaced about one week before I installed WM6.
Click to expand...
Click to collapse
Hey LastNikita,
I had the same problem ! The white scanlines thing just after re-updating a WM6 version (pdaviet), because I was tired of the constant reset issue.. suddenly, the update went wrong, and I stupidly followed the "recovery" process, which tells u to remove the battery... bang ! screen went corrupted !
Like you, I tought it was over... but I noticed that if you connect your phone and PC with USB, and keep pressed power (ON/OFF button on side) + camera after reseting (little hole on bottom - press during 5 sec!), the PC recognizes a USB device (not the usual phone drivers...) at this moment, I launched the Jester 3.3 (step1) update, in order to downgrade from the ugly WM6 pdaviet... My phone was not yet fixed (still with white scanlines), but at least, I could hear again the WM "start" sound, the scanlines would also "move" across the screen borders when I touched the screen, which made me imagine I was on the calibrating process... also, while connected to PC, after a while, ActiveSync would launch, asking for 1st time synch... this kept me confident as the phone (software) seemed to be reacting fine although HW prob...
I completely charged the phone again (till green light) then kept on reseting the phone (until I hear the WM sound) hoping the lines would finish scanning and come back with the normal .. and guess what, it did !!! Of course, PIGHEAD as I am, I wasn't totally happy it recovered with WM5, so i digged for a better rom, and I can tell you I'm very happy with the smart1 (wizard version) which works fine, but still has some minor bugs as Live Messenger not working... but runs fine (specialy when pressing the ON/OFF button !
PS: Make sure the ALWAYS completely switch off your phone (ON/OFF for 3 secs) before removing the battery... it did happen again... when I stupidly trusted the "recovery" process, again !
DUHHHH !!!!
PS: at least, now you ALL know !
Kokiri
Finally ok for warranty )))
Thanks for sharing mate
I finally managed to downgrade to my original Orange rom, and I'm in the process of putting the original Orange splash screens back (I made the nk.nbf but I can't find the right utility to upgrade... "Update utility cannot open the requested file").
BUT I still have that HW problem afterall.... so I guess it still has to go back to warranty right ? This isn't a big deal since Orange is VERY prompt (I guess I'll get it tomorrow or monday morning, the delivery guy brings a new one and goes back wiv my phone, quite nice !), and I have a button which is stucked (from the begining) anyway ^^
While I'm writing this my phone is docked and synced, and it seems fine.... but, I guess, as soon as I will reset it will start over again.... I'll keep you posted.
Anyway, I'm no longer desesperate and that's good news (for me ^^)
++
niko
yip
ok, everything's back to original.
Actually, it works well when docked, but it freezes/melted screen as soon as I tried to use it on battery, so that I'm quite sure it has something to do wiv WM6.... I'll post that on some crossbow threads this weekend if I have time enough (there are so many of them now !)....
But once more, if YOU read this, keep that in mind.
Hope you guys won't have that kind of failure while trying it.
++
niko
confused
I am having the same problem except the screen showing white scanlines everything else is working on the handset. Could it be a LCD Problem?
Me too...
I have the same issue (black/colored vertical lines and a white screen). I think it has to do with upgrading to WM6 or with overclocking with batteryStatus, not sure. This are the suspects in my opinion....
Now I downgraded to WM5 but the problem seems to persist, I disabled batteryStatus and will see if the situation improves... crossing fingers
Uhm ... possible Overclocked!
I have read 3 threads with same errors!
how much was your highes clock? do you use it for navigation? long time on highest clock or only for speed up?
i dont have a problem with scan lines but with my prophet i use the scaling option and go max to 234 i also set to 234 when using certain apps.
is this damaging to my prophet?
at the moment trying to upgrade to PDAViet 4.0.0.0.3 with a world of pain but thats another topic!

my wizard is dead please help out - urgently

can anyone help me out.... the battery in my wizard is dead ....
while doing the upgrade smart1_wm6_pp8mbs ... on my imate kjam IPL - 3.08 SPL - 3.08 GSM - 02.69.11 it gave me an error at the installation and my phone just went off..
when i tried to reset my phone its showed me a new OS 10.1.0.811 (which i think in not fully installed) and does not proceed further...... next i tried to reinstall xplore 1.1 back into my phone, at the time of installation the battery of the phone went dead ...... (cant reset or do anything now)
1. do you think my mobile is bricked
2. is there any way to charge my battery (at the three colour display)
3. is there a software where i can clear up and put in a new SPL/IPL/GSM/OS
Thanks Guys
steve-11 said:
1. do you think my mobile is bricked
Click to expand...
Click to collapse
No.
steve-11 said:
2. is there any way to charge my battery (at the three colour display)
Click to expand...
Click to collapse
Wait for a bit for the battery to settle down, and try turning the device on. If it turns on and you get stuck on ROM version splash, switch it to boot mode (soft-reset while holding Camera). Once in boot mode, power button will work to turn the device off. Hook the device up to a wall charger (not USB cable) and it will charge up, effectively un-bricking. Allow it to charge up to 100% before any flash attempt.
The point here is that a device does not charge up while in ROM version splash or in boot mode, but only in boot mode does the power button work to turn it off (at least in my device).
steve-11 said:
3. is there a software where i can clear up and put in a new SPL/IPL/GSM/OS
Click to expand...
Click to collapse
Download the latest, full ROM from your device manufacturer, and re-flash it while in boot mode (might not work under Vista or Server 2003, use Windows XP/ActiveSync 4.5 to flash).
Hard-reset the device, and once asked, press Send key to reformat FAT partition. You might get the dreaded "Format is failed" error message. The only way out of this is backing up and restoring from a miniSD card, which includes an additional BINFS formatting step, not present when flashing from boot. For a complete procedure, see:
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck.
Gary
gniemcew said:
No.
Wait for a bit for the battery to settle down, and try turning the device on. If it turns on and you get stuck on ROM version splash, switch it to boot mode (soft-reset while holding Camera). Once in boot mode, power button will work to turn the device off. Hook the device up to a wall charger (not USB cable) and it will charge up, effectively un-bricking. Allow it to charge up to 100% before any flash attempt.
The point here is that a device does not charge up while in ROM version splash or in boot mode, but only in boot mode does the power button work to turn it off (at least in my device).
Download the latest, full ROM from your device manufacturer, and re-flash it while in boot mode (might not work under Vista or Server 2003, use Windows XP/ActiveSync 4.5 to flash).
Hard-reset the device, and once asked, press Send key to reformat FAT partition. You might get the dreaded "Format is failed" error message. The only way out of this is backing up and restoring from a miniSD card, which includes an additional BINFS formatting step, not present when flashing from boot. For a complete procedure, see:
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck.
Gary
Click to expand...
Click to collapse
hi Gary
Thanks for your promt answer but before i proceed with what you said to do...
1. Hook the device up to a wall charger (i dont have that) any other way ?
2.what are the keys for hard reset / and what is press Send key to reformat FAT partition ?
3.i am using xp pro with active sync 4.5 on the same
steve-11 said:
hi Gary
Thanks for your promt answer but before i proceed with what you said to do...
1. Hook the device up to a wall charger (i dont have that) any other way ?
2.what are the keys for hard reset / and what is press Send key to reformat FAT partition ?
3.i am using xp pro with active sync 4.5 on the same
Click to expand...
Click to collapse
Gray did you meant the wall charger (the usb charger) .......
i have done the same ....... but i have to ROM version splash (RGB) constanly on without the orange light showing (usally show when charging)... is this ok for a full charge
You probably don't need to charge the battery. If it is at the rainbow screen (RGB) and you get the word USB in the bottom left corner when you connect it to the computer, you are good to go to reflash your manufacturer ROM. Once you get a good flash of your manufacturer, you will be able to recharge your battery and will probably notice that you are still about 80%. I tried to flash 6 times and was still at 83%. Stay cool and put an official ROM back on and you will be back in business.
steve-11 said:
1. Hook the device up to a wall charger (i dont have that) any other way ?
Click to expand...
Click to collapse
No, PC-USB cable charging did not work for my Cingular 8125. I had it power-bricked as well, and powering it off with the power button and hooking it up to a wall charger was able to charge it back up. The only other way is to take your battery to a friend, a Radio Shack or a Circuit City, and ask the guys to charge it for you.
steve-11 said:
2.what are the keys for hard reset / and what is press Send key to reformat FAT partition ?
Click to expand...
Click to collapse
Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.
For more information, Read The Fine Manual, it's described in detail all over the place.
steve-11 said:
Gray did you meant the wall charger (the usb charger) .......
Click to expand...
Click to collapse
Yes, a wall charger USB cable, not a PC-USB cable. PC-USB cable did not work for me for some reason.
steve-11 said:
but i have to ROM version splash (RGB) constanly on without the orange light showing (usally show when charging)... is this ok for a full charge
Click to expand...
Click to collapse
No, as mentioned above, your device might not charge while in ROM version splash, or in boot-mode. ROM version splash and boot-mode RGB are two different things. If you are in ROM version splash (IPL/SPL/ROM/OS versions displayed with cellular operator logo), hold down Camera key and and press-in the right-side soft-reset spot with a stylus to switch it to the red-green-blue boot-mode. Once in red-green-blue boot-mode, press the power button to power off the device (it does not power off in splash, but powers off in boot). If it is powered off, and hooked up to a wall charger, the orange light will come on, indicating charging. Once it turns back to green, you are all set to re-flash.
You probably do want to fully re-charge your device before re-flashing, because if it dies in the middle of a flash, or in the middle of a miniSD card restore, you're back to square one.
Gary
gniemcew said:
No, PC-USB cable charging did not work for my Cingular 8125. I had it power-bricked as well, and powering it off with the power button and hooking it up to a wall charger was able to charge it back up. The only other way is to take your battery to a friend, a Radio Shack or a Circuit City, and ask the guys to charge it for you.
Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.
For more information, Read The Fine Manual, it's described in detail all over the place.
Yes, a wall charger USB cable, not a PC-USB cable. PC-USB cable did not work for me for some reason.
No, as mentioned above, your device might not charge while in ROM version splash, or in boot-mode. ROM version splash and boot-mode RGB are two different things. If you are in ROM version splash (IPL/SPL/ROM/OS versions displayed with cellular operator logo), hold down Camera key and and press-in the right-side soft-reset spot with a stylus to switch it to the red-green-blue boot-mode. Once in red-green-blue boot-mode, press the power button to power off the device (it does not power off in splash, but powers off in boot). If it is powered off, and hooked up to a wall charger, the orange light will come on, indicating charging. Once it turns back to green, you are all set to re-flash.
You probably do want to fully re-charge your device before re-flashing, because if it dies in the middle of a flash, or in the middle of a miniSD card restore, you're back to square one.
Gary
Click to expand...
Click to collapse
Thanks Gray for your help .... hope it works
will keep you updated
gniemcew said:
No, PC-USB cable charging did not work for my Cingular 8125. I had it power-bricked as well, and powering it off with the power button and hooking it up to a wall charger was able to charge it back up. The only other way is to take your battery to a friend, a Radio Shack or a Circuit City, and ask the guys to charge it for you.
Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.
For more information, Read The Fine Manual, it's described in detail all over the place.
Yes, a wall charger USB cable, not a PC-USB cable. PC-USB cable did not work for me for some reason.
No, as mentioned above, your device might not charge while in ROM version splash, or in boot-mode. ROM version splash and boot-mode RGB are two different things. If you are in ROM version splash (IPL/SPL/ROM/OS versions displayed with cellular operator logo), hold down Camera key and and press-in the right-side soft-reset spot with a stylus to switch it to the red-green-blue boot-mode. Once in red-green-blue boot-mode, press the power button to power off the device (it does not power off in splash, but powers off in boot). If it is powered off, and hooked up to a wall charger, the orange light will come on, indicating charging. Once it turns back to green, you are all set to re-flash.
You probably do want to fully re-charge your device before re-flashing, because if it dies in the middle of a flash, or in the middle of a miniSD card restore, you're back to square one.
Gary
Click to expand...
Click to collapse
Hi Gary
i have got my battery charged and tried installing a new rom ..... but at the second splash screen its stuck...... i think i have a OS problem ..... it shows me OS 10.1.0.81 (this happened when i was installing smart1_wm6_pp8mb)
i also tried to do what you said - (Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.)
it cames back to the second splash screen ....... is there any hard format i can do
steve-11 said:
Hi Gary
i have got my battery charged and tried installing a new rom ..... but at the second splash screen its stuck...... i think i have a OS problem ..... it shows me OS 10.1.0.81 (this happened when i was installing smart1_wm6_pp8mb)
i also tried to do what you said - (Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.)
it cames back to the second splash screen ....... is there any hard format i can do
Click to expand...
Click to collapse
No siree Bob. That's not what's gonna help you.
You need to get into the bootloader screen (tri-color screen). To do this, you need to press and hold the camera button and just tap and release the reset button (while still holding in the camera button). Now you're at the tri-color screen (you can release the camera button now).
Now, connect the USB cable to your computer that has Activesync installed. Now, just download and install your original carrier ROM to the phone as you would normally do. That's it!
Magically you will have a working phone again.
steve-11 said:
Hi Gary
i think i have a OS problem .....
Click to expand...
Click to collapse
Yes you do. Find your original mfr. ROM and flash it first before you go any further.
jwzg said:
Yes you do. Find your original mfr. ROM and flash it first before you go any further.
Click to expand...
Click to collapse
i have the shipped version .... k-jam wwe 216901_2169101_020710_ship.exe (error 296) upgrade only
this NBF file cannot be used for your PDA phone. Please get newer NBF file
what should i do now
steve-11 said:
i have the shipped version .... but when installing is says error 300 get a newer update.....
do you have any ideal where i can get the original imate rom
Click to expand...
Click to collapse
... download it from I-Mate's website...
And you better hurry before your battery dies again.
You could always use the Love ROM if you can't get an original.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
TaurusBullba said:
... download it from I-Mate's website...
And you better hurry before your battery dies again.
Click to expand...
Click to collapse
my battery is fully charged..... but the problem is the imate site is not allowing me to download ..... asking me to pay for it
steve-11 said:
my battery is fully charged..... but the problem is the imate site is not allowing me to download ..... asking me to pay for it
Click to expand...
Click to collapse
See above post.
steve-11 said:
can anyone help me out.... the battery in my wizard is dead ....
while doing the upgrade smart1_wm6_pp8mbs ... on my imate kjam IPL - 3.08 SPL - 3.08 GSM - 02.69.11 it gave me an error at the installation and my phone just went off..
when i tried to reset my phone its showed me a new OS 10.1.0.811 (which i think in not fully installed) and does not proceed further...... next i tried to reinstall xplore 1.1 back into my phone, at the time of installation the battery of the phone went dead ...... (cant reset or do anything now)
1. do you think my mobile is bricked
2. is there any way to charge my battery (at the three colour display)
3. is there a software where i can clear up and put in a new SPL/IPL/GSM/OS
Thanks Guys
Click to expand...
Click to collapse
I had the same problem of the battery not charging from the 3 colour boot screen. Your phone is definately recoverable but first you need to get a fully charged battery. the only way i could find to do this was to buy a new battery from ebay that came with a free desktop charger. It was about £10 i think. A small price to pay for recovering your wizard mate.
TaurusBullba said:
You could always use the Love ROM if you can't get an original.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
Click to expand...
Click to collapse
+1, this rom saved me
steve-11 said:
i have got my battery charged
Click to expand...
Click to collapse
Ok, excellent.
steve-11 said:
but at the second splash screen its stuck...... i think i have a OS problem
Click to expand...
Click to collapse
Not necessarily. My understanding is that for a flashed OS to boot, it needs a FAT partition, just like a desktop OS. A FAT partition lives inside a BINFS storage system. If a device gets stuck in the ROM version splash screen (operator logo and multiple version numbers) your OS installation might be fine, but it cannot access its expected file system, and - just like a desktop OS - just hangs. To see if that is the case, do the hard-reset + Send procedure I describe again below. If this *is* a BINFS problem, you will get the "Format is failed" error message.
Is that what's happening with your device?
If so, re-flashing a ROM does NOT fix that problem, since flashing a ROM does nothing to re-initialize BINFS, allowing later FAT partition format. Yes, I agree it is pretty dumb of HTC not to include such an important step in a complete flash or a hard-reset, but that's just how things are. BINFS initialization, however, *is* a part of a miniSD card backup and restore process. Buy a cheap, $10 miniSD card (I used 256MB), and follow the procedure in the link I posted earlier.
steve-11 said:
it cames back to the second splash screen ....... is there any hard format i can do
Click to expand...
Click to collapse
You are probably letting go of Comms + Voice keys too early, effectively getting into a soft-reset instead of hard-reset. Keep holding those two keys, "do not let go" (to use the "Titanic" line ), and press in the reset spot with a stylus. Keep holding the keys. Screen will turn black and sit there for a while. Keep holding the keys. The device will turn back on, and a message should come up asking you whether you want to go back to factory settings. Keep holding Commns + Voice, hold down Send (green phone icon), and THEN let go of Comms + Voice. A FAT format should commence.
steve-11 said:
my battery is fully charged..... but the problem is the imate site is not allowing me to download ..... asking me to pay for it
Click to expand...
Click to collapse
Well, can't help there, since I have a Cingular 8125.
Gary
Any official rom will work (Cingular, T-Mobile, whatever). I have a K-JAM and the Cingular ROM got me loaded back up from the rainbow screen and I was able to load XPLORE afterwards.
phew guys ... thanks.. awesome thread.. btw i din kno tht little hole was a rest button i thot it for u kno just there

NBD 7.9 & Boot problem

Hi,
I have installed ~2 weeks ago NBD 7.9 and everything was ok. Today I have restarted my phone to change my SIM card but my phone could not start.
I see HTC logo but phone freezes after having NBD logo and nothing happens.
As you can image because of could not connecting to the phone, I can not also update ROM.
Any tip to recover my phone?
Did you try a hard-reset?
Can you explain what exactly you mean? Probably I do not know what is hard reset on these devices.
Ok I have found hard reset on the page
http://wiki.xda-developers.com/index.php?pagename=WizardFAQ
But now there is no power also. I also could not boot anymore.
* Press and hold both the Comm Mannager Button and the Voice Command Button
* While keeping those two buttons pressed, press the Reset Button with your stylus
* After about a second you will be prompted for confirmation. Press the Talk Button to confirm
----
oh I see, you found it.
the hard reset set your phone to the "original state" of the ROM (in that case right after you installed your NDB rom).
what do you mean there is no power?
Could it be your battery is empty and needs to re-charged?
There is no response on the phone now.
I suspect battery is empty but when I try to connect power cord no response also.
If you are sure your battery is not empty try to get into the bootloader mode:
depending on the type (G3 or G4) follow the instructions:
http://forum.xda-developers.com/showthread.php?t=298613
especially step G3.2 or G4.2 respectively.
tarantor said:
There is no response on the phone now.
I suspect battery is empty but when I try to connect power cord no response also.
Click to expand...
Click to collapse
When I tried to connect to power while the phone is off it takes some seconds before response. Have try.
I have a G3 device (Vodafone VPA II Compact). But there is still no response.
I think it is power issue now. The bad thing is that I have only USB cable at home and the main power charger at work now.
Are there any way to charge with USB cable when phone is not open?
I would suggest following:
1. ensure your battery is full
2. do the hard-reset again - this may solve your problem already
3. if not, try to get into the bootloader mode (see the thread referred to above for instructions)
4. follow the instructions to re-load the ROM
tarantor said:
I have a G3 device (Vodafone VPA II Compact). But there is still no response.
I think it is power issue now. The bad thing is that I have only USB cable at home and the main power charger at work now.
Are there any way to charge with USB cable when phone is not open?
Click to expand...
Click to collapse
I just tried ... while your phone is off the USB connection to the PC should provide you the current .. at my case the WIZARD starts to charge .. have a try.
----------------
the red LED light on the right above the display indicates the charging .. and turns green once it is fully charged, so in any case, you should see a light, although it takes 3-5 seconds after connecting to the USB.
Does it work?
I have tried and there is no light. As I remember before it was not possible if you are not connected via ActiveSync.
Anyway, I can try Monday at office.
Thanks for your help!!!
You're welcome. Good luck for Monday. Hope it will work out. Not much help yet from me but I will be around here.
This was driving me mad as well. I had to put it into bootloader mode (holding camera while resetting) and flash back to the Tmob 2.26 and then reflashing nbd.
The trick is to disable the HTC home plugin before you install any other apps. From what I understand its to do with some mysterious dlls.
I found this out on Friday and so far I haven't had any problems but I guess its still early days.
Good luck!
OK. It was a power issue and I could make a hard reset at office and it works again now.
I will try NBD 8.1 and see the difference.
Thanks for your help a lot!
good to hear it is working again!

Broke SDA, miracle required??

So, I have an SDA (unlocked and all) and decided to upgrade to WM 6.1 using Karhoes guide. Everything went smooth and before you know my SDA had a new lease on life. Well, I continued reading on the forums about other WM 6.1 roms and decided that I wanted to get GnatGoSplat's WM 6.1 clean rom. (http://forum.xda-developers.com/showthread.php?t=380554) and this is where all Hell broke loose. I followed the directions and the SDA got stuck on a white screen forever (before I was ever able to run the ROM flash upgrade). So, I took the battery out, bad move I suppose and again I was greeted by the white screen. However, I was able to get into the bootloader so I ran TeraTermPro and did the format BINFS command. At this point things are looking good. Now I get back to the bootloader and I can see the USB connection in the bottom left hand corner and I can hear it connecting to the PC but ActiveSync won't detect it. No biggie, but when I try to do the ROM install I get a connection error. And this is where I am stuck. Can anyone help??? I find it odd that the PC and the phone can connect but I can't update or restore the phone. Help!! TIA.
I had same problem, here is the trick fist step take off the battery and wait for 5 min. second step put the battery back and than press power button at the same time insert the mini usb cable and start pressing the button on left hand corner next to home buttom . try several time , good luck
Is this taking me into the bootloader?
press power button and than wait 1 or 2 second then insert the min usb while the phone boots up to bootloader then keep pressing left hand corner button make sure the usb cable is conected to computer
...and reinstall activesync and check allow usb conection to activesync pictogram.

Bt Htc S710 Original Rom

Hello forum members,
would you please help me have the BT HTC S710 Original ROM? I have only seen the BT HTC S620, which when I tried to flash with to rebrand, blanked my HTC S710 screen. When I turn it on, only the two green lights come on either side of the phone ear piece.
It means that a hard reset is not visible on my screen, there is no tri-colour display either.
I have tried other ROMS, and get invalid id errors and error 270. I have tried Dr Gonzo and related ROMS.
It's now three days, no phone no pim, I am lost.
Thanks for your attention.
YOSEFE.
PS. You may PM me if convenient.
Hi YOSEFE,
I have the same problem
I tried the 620 rom and just have the 2 green LED's. I cannot get a bootloader screen and attempts to flash new roms get to 3% and then I get errors.
Did you ever sort this problem out?
Paul.
Have you unlocked ur USPL in ur phone?
You tried to flash a S620 ROM to a S710???? Look in the Wiki, there is a link to the official ROMs on the ftp...
frauhottelmann said:
You tried to flash a S620 ROM to a S710???? Look in the Wiki, there is a link to the official ROMs on the ftp...
Click to expand...
Click to collapse
Yes, I'm afraid I did, by mistake, flash 620 ROM to the 710 [feels rather stupid!]
Not happy with BT’s [mobile operator] own ROM and software that went on the phone, I successfully flashed Dr. Martin Gonzo’s Windows Mobile 6.1 v1.1 and have been using it for a couple of months but when BT launched their new phone software, I decided to try it but because it won’t work with WM 6.1, I needed to then revert back to BT’s old ROM and this was the only one available that I could find [feels rather stupid again].
The screen is completely black; only green LED's on each side of the earpiece shows any sign of life.
Connecting the phone via ActiveSync shows “HTC-S620 Connected” and I am able to browse the files on the phone but not having a display on the phone, I am limited to what I can do.
I have tried running RUU_Vox_HTC_WWE_1.34.405.1_4.1.13.54_03.10.90_Ship.exe but ActiveSync connection is lost and I hear the Windows hardware removed sound shortly after the progress bar is shown.
I’m at a loss as to what to try
Paul.
Shut it down, then hold down camera button and plug in the usb cable. The boot screen should appear and you should be able to flash the normal ROM!
I cannot get the boot screen, or any screen for that matter.
I have tried taking the battery out to make sure the phone is off. Reinserting that battery then holding the camera button down and then inserting the usb lead. The keypad lights up for a few seconds then goes out. ActiveSync then connects but the screen is still black
Paul.
[Edited: Sorry duplicate post]
Sorry for replying to my own post but a quick update...
I have managed to bring the phone back to life and reinstall Dr. Martin Gonzo’s Windows Mobile 6.1 v1.1 on it again.
This is partly assumption and not particularly accurate but the original poster (YOSEFE) might find this useful.
By installing the S620 rom on the S710, not only did I make the screen go blank, I think all the keys ended up remapped and mixed up, therefore any attempt to install Gonzo’s rom ultimately ended in failure because when the phone beeped and wanted a keypress to continue, pressing the left softkey for ‘OK’ or ‘Yes’ did not work because it had been remapped to do something else.
What worked for me is that when the phone beeped during the uspl_116_jockyw.bat install, I pressed the X or C key (I can’t remember the exact one now). One of these keys must have been the ‘OK’ or ‘Yes’ key after the S620 rom muddled things up. I only know this by trial and error over the period of today.
To my glee, the backlight lit up on the display and after a bit of tinkering, I’m back in action again
I won’t be installing a rom designed for another model again!
Paul.
Bat 'n' Ball,
sorry for not returning here to see your post. I will remember the possibility of pressing "X" or "C", should I make the same mistake as before, although like you, I should never do that ever again. However, technology being what it is, who knows?
In the end BT got me sorted out.
Thanks for sharing.

Categories

Resources