Hi,
I have installed ~2 weeks ago NBD 7.9 and everything was ok. Today I have restarted my phone to change my SIM card but my phone could not start.
I see HTC logo but phone freezes after having NBD logo and nothing happens.
As you can image because of could not connecting to the phone, I can not also update ROM.
Any tip to recover my phone?
Did you try a hard-reset?
Can you explain what exactly you mean? Probably I do not know what is hard reset on these devices.
Ok I have found hard reset on the page
http://wiki.xda-developers.com/index.php?pagename=WizardFAQ
But now there is no power also. I also could not boot anymore.
* Press and hold both the Comm Mannager Button and the Voice Command Button
* While keeping those two buttons pressed, press the Reset Button with your stylus
* After about a second you will be prompted for confirmation. Press the Talk Button to confirm
----
oh I see, you found it.
the hard reset set your phone to the "original state" of the ROM (in that case right after you installed your NDB rom).
what do you mean there is no power?
Could it be your battery is empty and needs to re-charged?
There is no response on the phone now.
I suspect battery is empty but when I try to connect power cord no response also.
If you are sure your battery is not empty try to get into the bootloader mode:
depending on the type (G3 or G4) follow the instructions:
http://forum.xda-developers.com/showthread.php?t=298613
especially step G3.2 or G4.2 respectively.
tarantor said:
There is no response on the phone now.
I suspect battery is empty but when I try to connect power cord no response also.
Click to expand...
Click to collapse
When I tried to connect to power while the phone is off it takes some seconds before response. Have try.
I have a G3 device (Vodafone VPA II Compact). But there is still no response.
I think it is power issue now. The bad thing is that I have only USB cable at home and the main power charger at work now.
Are there any way to charge with USB cable when phone is not open?
I would suggest following:
1. ensure your battery is full
2. do the hard-reset again - this may solve your problem already
3. if not, try to get into the bootloader mode (see the thread referred to above for instructions)
4. follow the instructions to re-load the ROM
tarantor said:
I have a G3 device (Vodafone VPA II Compact). But there is still no response.
I think it is power issue now. The bad thing is that I have only USB cable at home and the main power charger at work now.
Are there any way to charge with USB cable when phone is not open?
Click to expand...
Click to collapse
I just tried ... while your phone is off the USB connection to the PC should provide you the current .. at my case the WIZARD starts to charge .. have a try.
----------------
the red LED light on the right above the display indicates the charging .. and turns green once it is fully charged, so in any case, you should see a light, although it takes 3-5 seconds after connecting to the USB.
Does it work?
I have tried and there is no light. As I remember before it was not possible if you are not connected via ActiveSync.
Anyway, I can try Monday at office.
Thanks for your help!!!
You're welcome. Good luck for Monday. Hope it will work out. Not much help yet from me but I will be around here.
This was driving me mad as well. I had to put it into bootloader mode (holding camera while resetting) and flash back to the Tmob 2.26 and then reflashing nbd.
The trick is to disable the HTC home plugin before you install any other apps. From what I understand its to do with some mysterious dlls.
I found this out on Friday and so far I haven't had any problems but I guess its still early days.
Good luck!
OK. It was a power issue and I could make a hard reset at office and it works again now.
I will try NBD 8.1 and see the difference.
Thanks for your help a lot!
good to hear it is working again!
Related
can anyone help me out.... the battery in my wizard is dead ....
while doing the upgrade smart1_wm6_pp8mbs ... on my imate kjam IPL - 3.08 SPL - 3.08 GSM - 02.69.11 it gave me an error at the installation and my phone just went off..
when i tried to reset my phone its showed me a new OS 10.1.0.811 (which i think in not fully installed) and does not proceed further...... next i tried to reinstall xplore 1.1 back into my phone, at the time of installation the battery of the phone went dead ...... (cant reset or do anything now)
1. do you think my mobile is bricked
2. is there any way to charge my battery (at the three colour display)
3. is there a software where i can clear up and put in a new SPL/IPL/GSM/OS
Thanks Guys
steve-11 said:
1. do you think my mobile is bricked
Click to expand...
Click to collapse
No.
steve-11 said:
2. is there any way to charge my battery (at the three colour display)
Click to expand...
Click to collapse
Wait for a bit for the battery to settle down, and try turning the device on. If it turns on and you get stuck on ROM version splash, switch it to boot mode (soft-reset while holding Camera). Once in boot mode, power button will work to turn the device off. Hook the device up to a wall charger (not USB cable) and it will charge up, effectively un-bricking. Allow it to charge up to 100% before any flash attempt.
The point here is that a device does not charge up while in ROM version splash or in boot mode, but only in boot mode does the power button work to turn it off (at least in my device).
steve-11 said:
3. is there a software where i can clear up and put in a new SPL/IPL/GSM/OS
Click to expand...
Click to collapse
Download the latest, full ROM from your device manufacturer, and re-flash it while in boot mode (might not work under Vista or Server 2003, use Windows XP/ActiveSync 4.5 to flash).
Hard-reset the device, and once asked, press Send key to reformat FAT partition. You might get the dreaded "Format is failed" error message. The only way out of this is backing up and restoring from a miniSD card, which includes an additional BINFS formatting step, not present when flashing from boot. For a complete procedure, see:
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck.
Gary
gniemcew said:
No.
Wait for a bit for the battery to settle down, and try turning the device on. If it turns on and you get stuck on ROM version splash, switch it to boot mode (soft-reset while holding Camera). Once in boot mode, power button will work to turn the device off. Hook the device up to a wall charger (not USB cable) and it will charge up, effectively un-bricking. Allow it to charge up to 100% before any flash attempt.
The point here is that a device does not charge up while in ROM version splash or in boot mode, but only in boot mode does the power button work to turn it off (at least in my device).
Download the latest, full ROM from your device manufacturer, and re-flash it while in boot mode (might not work under Vista or Server 2003, use Windows XP/ActiveSync 4.5 to flash).
Hard-reset the device, and once asked, press Send key to reformat FAT partition. You might get the dreaded "Format is failed" error message. The only way out of this is backing up and restoring from a miniSD card, which includes an additional BINFS formatting step, not present when flashing from boot. For a complete procedure, see:
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck.
Gary
Click to expand...
Click to collapse
hi Gary
Thanks for your promt answer but before i proceed with what you said to do...
1. Hook the device up to a wall charger (i dont have that) any other way ?
2.what are the keys for hard reset / and what is press Send key to reformat FAT partition ?
3.i am using xp pro with active sync 4.5 on the same
steve-11 said:
hi Gary
Thanks for your promt answer but before i proceed with what you said to do...
1. Hook the device up to a wall charger (i dont have that) any other way ?
2.what are the keys for hard reset / and what is press Send key to reformat FAT partition ?
3.i am using xp pro with active sync 4.5 on the same
Click to expand...
Click to collapse
Gray did you meant the wall charger (the usb charger) .......
i have done the same ....... but i have to ROM version splash (RGB) constanly on without the orange light showing (usally show when charging)... is this ok for a full charge
You probably don't need to charge the battery. If it is at the rainbow screen (RGB) and you get the word USB in the bottom left corner when you connect it to the computer, you are good to go to reflash your manufacturer ROM. Once you get a good flash of your manufacturer, you will be able to recharge your battery and will probably notice that you are still about 80%. I tried to flash 6 times and was still at 83%. Stay cool and put an official ROM back on and you will be back in business.
steve-11 said:
1. Hook the device up to a wall charger (i dont have that) any other way ?
Click to expand...
Click to collapse
No, PC-USB cable charging did not work for my Cingular 8125. I had it power-bricked as well, and powering it off with the power button and hooking it up to a wall charger was able to charge it back up. The only other way is to take your battery to a friend, a Radio Shack or a Circuit City, and ask the guys to charge it for you.
steve-11 said:
2.what are the keys for hard reset / and what is press Send key to reformat FAT partition ?
Click to expand...
Click to collapse
Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.
For more information, Read The Fine Manual, it's described in detail all over the place.
steve-11 said:
Gray did you meant the wall charger (the usb charger) .......
Click to expand...
Click to collapse
Yes, a wall charger USB cable, not a PC-USB cable. PC-USB cable did not work for me for some reason.
steve-11 said:
but i have to ROM version splash (RGB) constanly on without the orange light showing (usally show when charging)... is this ok for a full charge
Click to expand...
Click to collapse
No, as mentioned above, your device might not charge while in ROM version splash, or in boot-mode. ROM version splash and boot-mode RGB are two different things. If you are in ROM version splash (IPL/SPL/ROM/OS versions displayed with cellular operator logo), hold down Camera key and and press-in the right-side soft-reset spot with a stylus to switch it to the red-green-blue boot-mode. Once in red-green-blue boot-mode, press the power button to power off the device (it does not power off in splash, but powers off in boot). If it is powered off, and hooked up to a wall charger, the orange light will come on, indicating charging. Once it turns back to green, you are all set to re-flash.
You probably do want to fully re-charge your device before re-flashing, because if it dies in the middle of a flash, or in the middle of a miniSD card restore, you're back to square one.
Gary
gniemcew said:
No, PC-USB cable charging did not work for my Cingular 8125. I had it power-bricked as well, and powering it off with the power button and hooking it up to a wall charger was able to charge it back up. The only other way is to take your battery to a friend, a Radio Shack or a Circuit City, and ask the guys to charge it for you.
Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.
For more information, Read The Fine Manual, it's described in detail all over the place.
Yes, a wall charger USB cable, not a PC-USB cable. PC-USB cable did not work for me for some reason.
No, as mentioned above, your device might not charge while in ROM version splash, or in boot-mode. ROM version splash and boot-mode RGB are two different things. If you are in ROM version splash (IPL/SPL/ROM/OS versions displayed with cellular operator logo), hold down Camera key and and press-in the right-side soft-reset spot with a stylus to switch it to the red-green-blue boot-mode. Once in red-green-blue boot-mode, press the power button to power off the device (it does not power off in splash, but powers off in boot). If it is powered off, and hooked up to a wall charger, the orange light will come on, indicating charging. Once it turns back to green, you are all set to re-flash.
You probably do want to fully re-charge your device before re-flashing, because if it dies in the middle of a flash, or in the middle of a miniSD card restore, you're back to square one.
Gary
Click to expand...
Click to collapse
Thanks Gray for your help .... hope it works
will keep you updated
gniemcew said:
No, PC-USB cable charging did not work for my Cingular 8125. I had it power-bricked as well, and powering it off with the power button and hooking it up to a wall charger was able to charge it back up. The only other way is to take your battery to a friend, a Radio Shack or a Circuit City, and ask the guys to charge it for you.
Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.
For more information, Read The Fine Manual, it's described in detail all over the place.
Yes, a wall charger USB cable, not a PC-USB cable. PC-USB cable did not work for me for some reason.
No, as mentioned above, your device might not charge while in ROM version splash, or in boot-mode. ROM version splash and boot-mode RGB are two different things. If you are in ROM version splash (IPL/SPL/ROM/OS versions displayed with cellular operator logo), hold down Camera key and and press-in the right-side soft-reset spot with a stylus to switch it to the red-green-blue boot-mode. Once in red-green-blue boot-mode, press the power button to power off the device (it does not power off in splash, but powers off in boot). If it is powered off, and hooked up to a wall charger, the orange light will come on, indicating charging. Once it turns back to green, you are all set to re-flash.
You probably do want to fully re-charge your device before re-flashing, because if it dies in the middle of a flash, or in the middle of a miniSD card restore, you're back to square one.
Gary
Click to expand...
Click to collapse
Hi Gary
i have got my battery charged and tried installing a new rom ..... but at the second splash screen its stuck...... i think i have a OS problem ..... it shows me OS 10.1.0.81 (this happened when i was installing smart1_wm6_pp8mb)
i also tried to do what you said - (Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.)
it cames back to the second splash screen ....... is there any hard format i can do
steve-11 said:
Hi Gary
i have got my battery charged and tried installing a new rom ..... but at the second splash screen its stuck...... i think i have a OS problem ..... it shows me OS 10.1.0.81 (this happened when i was installing smart1_wm6_pp8mb)
i also tried to do what you said - (Hold left-side upper Comms button + right-side upper Voice button and press-in the right-side middle soft-reset spot with a stylus. Keep holding the keys and after a reset your device will ask you to press in the Send key (the key used to answer an incoming call) to FAT format. Hold Send and release Comms + Voice and off you are.)
it cames back to the second splash screen ....... is there any hard format i can do
Click to expand...
Click to collapse
No siree Bob. That's not what's gonna help you.
You need to get into the bootloader screen (tri-color screen). To do this, you need to press and hold the camera button and just tap and release the reset button (while still holding in the camera button). Now you're at the tri-color screen (you can release the camera button now).
Now, connect the USB cable to your computer that has Activesync installed. Now, just download and install your original carrier ROM to the phone as you would normally do. That's it!
Magically you will have a working phone again.
steve-11 said:
Hi Gary
i think i have a OS problem .....
Click to expand...
Click to collapse
Yes you do. Find your original mfr. ROM and flash it first before you go any further.
jwzg said:
Yes you do. Find your original mfr. ROM and flash it first before you go any further.
Click to expand...
Click to collapse
i have the shipped version .... k-jam wwe 216901_2169101_020710_ship.exe (error 296) upgrade only
this NBF file cannot be used for your PDA phone. Please get newer NBF file
what should i do now
steve-11 said:
i have the shipped version .... but when installing is says error 300 get a newer update.....
do you have any ideal where i can get the original imate rom
Click to expand...
Click to collapse
... download it from I-Mate's website...
And you better hurry before your battery dies again.
You could always use the Love ROM if you can't get an original.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
TaurusBullba said:
... download it from I-Mate's website...
And you better hurry before your battery dies again.
Click to expand...
Click to collapse
my battery is fully charged..... but the problem is the imate site is not allowing me to download ..... asking me to pay for it
steve-11 said:
my battery is fully charged..... but the problem is the imate site is not allowing me to download ..... asking me to pay for it
Click to expand...
Click to collapse
See above post.
steve-11 said:
can anyone help me out.... the battery in my wizard is dead ....
while doing the upgrade smart1_wm6_pp8mbs ... on my imate kjam IPL - 3.08 SPL - 3.08 GSM - 02.69.11 it gave me an error at the installation and my phone just went off..
when i tried to reset my phone its showed me a new OS 10.1.0.811 (which i think in not fully installed) and does not proceed further...... next i tried to reinstall xplore 1.1 back into my phone, at the time of installation the battery of the phone went dead ...... (cant reset or do anything now)
1. do you think my mobile is bricked
2. is there any way to charge my battery (at the three colour display)
3. is there a software where i can clear up and put in a new SPL/IPL/GSM/OS
Thanks Guys
Click to expand...
Click to collapse
I had the same problem of the battery not charging from the 3 colour boot screen. Your phone is definately recoverable but first you need to get a fully charged battery. the only way i could find to do this was to buy a new battery from ebay that came with a free desktop charger. It was about £10 i think. A small price to pay for recovering your wizard mate.
TaurusBullba said:
You could always use the Love ROM if you can't get an original.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
Click to expand...
Click to collapse
+1, this rom saved me
steve-11 said:
i have got my battery charged
Click to expand...
Click to collapse
Ok, excellent.
steve-11 said:
but at the second splash screen its stuck...... i think i have a OS problem
Click to expand...
Click to collapse
Not necessarily. My understanding is that for a flashed OS to boot, it needs a FAT partition, just like a desktop OS. A FAT partition lives inside a BINFS storage system. If a device gets stuck in the ROM version splash screen (operator logo and multiple version numbers) your OS installation might be fine, but it cannot access its expected file system, and - just like a desktop OS - just hangs. To see if that is the case, do the hard-reset + Send procedure I describe again below. If this *is* a BINFS problem, you will get the "Format is failed" error message.
Is that what's happening with your device?
If so, re-flashing a ROM does NOT fix that problem, since flashing a ROM does nothing to re-initialize BINFS, allowing later FAT partition format. Yes, I agree it is pretty dumb of HTC not to include such an important step in a complete flash or a hard-reset, but that's just how things are. BINFS initialization, however, *is* a part of a miniSD card backup and restore process. Buy a cheap, $10 miniSD card (I used 256MB), and follow the procedure in the link I posted earlier.
steve-11 said:
it cames back to the second splash screen ....... is there any hard format i can do
Click to expand...
Click to collapse
You are probably letting go of Comms + Voice keys too early, effectively getting into a soft-reset instead of hard-reset. Keep holding those two keys, "do not let go" (to use the "Titanic" line ), and press in the reset spot with a stylus. Keep holding the keys. Screen will turn black and sit there for a while. Keep holding the keys. The device will turn back on, and a message should come up asking you whether you want to go back to factory settings. Keep holding Commns + Voice, hold down Send (green phone icon), and THEN let go of Comms + Voice. A FAT format should commence.
steve-11 said:
my battery is fully charged..... but the problem is the imate site is not allowing me to download ..... asking me to pay for it
Click to expand...
Click to collapse
Well, can't help there, since I have a Cingular 8125.
Gary
Any official rom will work (Cingular, T-Mobile, whatever). I have a K-JAM and the Cingular ROM got me loaded back up from the rainbow screen and I was able to load XPLORE afterwards.
phew guys ... thanks.. awesome thread.. btw i din kno tht little hole was a rest button i thot it for u kno just there
I flashed my XDA Exec with Leo's V7 Videocall ROM which all appeared to go fine until I performed the hard reset to reinstall.
It rebooted to the white screen asking you to press 0 to reinstall or X to exit, so I pressed 0. The screen briefly displayed a 'clearing' message and then went blank. There is no further response from the unit from any input except when I try to hard reset the device and reinstall again.
Just soft resetting the device only continues to give a blank screen and trying to power on the device in a normal manner also only gives a blank screen.
Windows XP fails to recognise the device when it is plugged in via USB either at the hard reset screen or soft reset or complete power off (remove battery, etc) then power on.
I updated to ActiveSync45 prior to the first hard reset.
Does anybody have suggestions or ideas on how to un-brick this Universal?
seems broken DOC chip. how many years you UNIVERSAL
It's about 18 months old now.
What is the DOC chip and why would it only fail at an upgrade?
Try a re-flash
Hi have you tried re-flashing the device?
Enter BootLoader mode, hold Power & BackLight button & press Reset, this will show Serial or USB on the screen. Start the flash off again or try another Rom (maybe the one you have is corrupt)
Cheers,
Beat
Hi Beast,
Yeah, I stumbled across these instructions today (http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen) and will give that a go tonight when I get home.
Thanks for the suggestion - I'll report back once I've tried it.
jamver - did you charge before flashing your new BIOS? it can go blank just because the battery could be dying and despite seeing some charge in the indicator, in fact the batt would be exhausted.
Hi jamver, I also encountered the same issue as you a few months back. Symptoms sound similar. I tried the points described in this thread:
http://forum.xda-developers.com/showthread.php?t=289325
Also, upgraded my bootloader and the device came back to life. One thing I learned also is that not all USB cables are made the same. If you find one USB cable doesn't work, you may want to try another. (my case, using a poor quality cable resulted in the "serial" word on the screen not changing to "USB")
Good luck and all the best!
Fixed
Thanks for the help guys. Manually putting it into bootloader mode and re-flashing it worked.
WM6 is significantly faster than any image of WM5 I've used!
hello,
i've ever meet this problem.. but after reflashing in bootloader mode all restart pefect !
So, I have an SDA (unlocked and all) and decided to upgrade to WM 6.1 using Karhoes guide. Everything went smooth and before you know my SDA had a new lease on life. Well, I continued reading on the forums about other WM 6.1 roms and decided that I wanted to get GnatGoSplat's WM 6.1 clean rom. (http://forum.xda-developers.com/showthread.php?t=380554) and this is where all Hell broke loose. I followed the directions and the SDA got stuck on a white screen forever (before I was ever able to run the ROM flash upgrade). So, I took the battery out, bad move I suppose and again I was greeted by the white screen. However, I was able to get into the bootloader so I ran TeraTermPro and did the format BINFS command. At this point things are looking good. Now I get back to the bootloader and I can see the USB connection in the bottom left hand corner and I can hear it connecting to the PC but ActiveSync won't detect it. No biggie, but when I try to do the ROM install I get a connection error. And this is where I am stuck. Can anyone help??? I find it odd that the PC and the phone can connect but I can't update or restore the phone. Help!! TIA.
I had same problem, here is the trick fist step take off the battery and wait for 5 min. second step put the battery back and than press power button at the same time insert the mini usb cable and start pressing the button on left hand corner next to home buttom . try several time , good luck
Is this taking me into the bootloader?
press power button and than wait 1 or 2 second then insert the min usb while the phone boots up to bootloader then keep pressing left hand corner button make sure the usb cable is conected to computer
...and reinstall activesync and check allow usb conection to activesync pictogram.
I know this is a bit of an old phone now, but I'm hoping someone might be able to help...
When I switch the phone on, it gets to the Windows Mobile screen and then just hangs. After a few minutes, it turns itself off.
So far, I've tried the following;
1. Soft reset
2. Hard reset
3. Remove battery, put on charge (red light), replace battery (amber light), hard reset
4. Removed battery for 2 weeks
5. Praying
6. Swearing
Does anyone have any other suggestions?
Thx
Bad Flash
Hi
You could try starting the device in bootloader in order to re-flash the ROM, or flash a new ROM. Methods for this are:
1) Press the soft reset hole button whilst holding camera button fully in.
2) Remove the battery, then re-insert it and switch the device on by pressing the power button but again ensuring the camera button is depressed fully.
3) Remove the battery and re-insert it. Don't switch the device on but plug it into a Windows PC using a USB cable whilst, you guessed it, depressing the camera button.
If you can get into bootloader (three coloured screen with some yellow writing) then you can probably reflash the device. It sounds like a software problem not a hardware problem but I could be wrong on that.
If you can't get the device into bootloader mode you have a problem that is more complicated to fix, about which I can't advice.
Best wishes
andrew-in-woking
For info
Check out these definitions:
http://forum.xda-developers.com/showthread.php?t=319077
http://forum.xda-developers.com/showthread.php?t=356299
http://forum.xda-developers.com/showthread.php?t=273831
Awaiting an update!
Cheers
andrew-in-woking
Hi,
Thanks for the reply....I couldn't get your method to bring up the bootloader to work, but tried pressing Power and OK while doing a soft reset.
This brought up a screen with 4 horizontal bars - red, green blue & white. Text at the top says;
HERM100 (text in white)
IPL-1.01
HERM100 (text in yellow)
SPL-1.04
In the white bar is the word 'Serial'
Does this sound right?
Then it just hangs on this screen - is there something else I am supposed press on the phone, or do I do something via my laptop with activesync etc?
Sorry for the additional questions, but I've never had to do this before.
Thanks
An update....
After noticing that 'No GSM' appears on the splash screen, I have now found this page which I think might answer my questions.
I'll have a go at this tonight
Reposted in the Hermes thread
Please help me guys . I tried to flash my phone. I conetcted the phone with active synch then on compiuter start the hard spl exe. Then i wait 2 minits and on my computer screen pop up new window and there write coz error 260. So then i dosconect the usb from pc , pick up the phone baterry wait 3 second then put battery to the phone but still doesn't response. I can push tur on button or reset button . But nothink!!!! please help what i need to do?
Before you flashed, you did make sure that you installed Microsoft .NET Framework 3.5 (mentioned in that same post)
Did any of the following happen?
*DO NOT start another process while the flashing process is taking place*
*DO NOT click off of the status bar... Let it stay in the foreground*
*DO NOT let the Screensaver activate*
(any of these can lead to a bad flash and possibly brick your phone)
Click to expand...
Click to collapse
If so, then you have possibly bricked your phone, my friend
Also, did you wait for it to sync and can you enter bootloader? Hold the volume down key and press the power key/reset button and release the volume down key when you see the multi-color screen.
Additionally, you should be able to remove all cards and your battery and be able to get into bootloader mode by holding the volume down key and connecting to your computer.
R^7Z said:
Additionally, you should be able to remove all cards and your battery and be able to get into bootloader mode by holding the volume down key and connecting to your computer.
Click to expand...
Click to collapse
I tried now to do it i insrt usb to pc and pocket pc then hold volume down key. But nothing. Mayby you have skype i wna to comunicate with you faster. And maybe you can help to me wat can i do now. Thx for answering
How long did you hold the volume down key? I have to wait at least 2 - 3 seconds from when I connect the cable to my device as I have the USB cable already connected to my PC. In other words, hold the volume key down while you are doing all of this, till you see the multicolor screen.
i can hold it 3 or even 6 minits. but you say something about the colours. when i install the spl with synchronization my phone just like died. i dont know wats hapen. and now i dont see any colours on my phone screen. now the screen is black.when i put battery in my phone about after 3 hours my phone back a litle worm. i dont know what to do.
That sounds like you bricked it. Sorry to hear but if you are positive that you did everything as the post I linked you to, mentioned, then it should work. I'm not sure where the process stopped working for you but perhaps you can try retracing the steps? Although, it does sound like you missed a step and now you're phone is bricked. I'm also not sure if you understand what I am saying or asking you to do but I guess if it isn't working, it just isn't working?
Synchronized Well I just shook my phone and the program's EXE file in the SPL. and then there shook far, far away and then threw away so that you do not click anything, not combine any other program. I do and do it. I've been waiting for. Then I look at my phone screen and blacked everything. Then dropped onto a computer error 260th And I do not know what I can do. It does not RESPOND at all. Even though I tried hard reset but still nothing happens. Maybe I should try to flash the phone to make a micro sd? Once uploaded there y card and then pressing a few buttons to be there? Extend the writing maybe?
I'm not 100% sure this will work unless you have HARD-SPL flashed to your device; which is where we stalled out the last time.
Once you have the stock ROM, rename it to RAPHIMG.nbh. Copy just that file to the root of your microSD (preferably a FAT32 formatted microSD but not required). Then, remove the SIM and hold the volume down key while you press the reset button and continue to hold the volume down key till you see the onscreen instructions. According to THIS post, this method should work for flashing a ROM. I am am not able to really say for sure that it does as I never really used or had to use the microSD flashing option.
This doesn't work to maybe i can somehow reinstall the original htc touch pro soft?
The only OTHER way would be through USB from bootloader but if you find it difficult to get that far, I don't know how else to help you my friend.
Maybe you can write a detail lession how can i do this? how can i louch that bootloader . Please help i realy need your help
Try it this way exactly:
Remove your battery, SIM and microSD. Now plug your USB cable to your device (not the computer). Hold the volume key down and plug the other end of the USB cable to your computer and wait till the multicolor screen comes up. If you do not see the multicolor screen, this may be an indication that the USB cord may be messed up (try another in this case), it may be the USB port (try another in this case) OR worse case senario, your phone is just plain bricked my friend...
Additionally, you may need to try another computer.
Once you get into bootloader we will need to go ahead and get hard-spl onto your device.
First, let me know when you get to the bootloader screen...
This doesn't work to ;(((((((((
I don't know what to say, it is sounding more and more like you've bricked your phone. Have you tried another cable / another USB port / another computer?
So, which raphael do you have? CDMA or GSM? And which hard spl did you flash: CDMA or GSM? And did you flash the raphael hard spl, or did you do something like flash the diamond hard spl (or the unlocker)?
If soft resetting the phone doesn't bring it back, then it's probably bricked. I have a feeling you flashed the wrong bootloader for the device.
so if i bricked my phone. No i can just throw it to the dump. or maybe i i send this phone to the repair shop. Maybe they gona repair it?
So, what bootloader did you flash, and what model do you have? If it's the wrong combo, I guess you could sell it on ebay for spare parts. You're not likely to get it fixed.
i have t-mobile mda htc touch pro. and i tried to flash it with Raphael_VZW_HSPL_035
My friend, if you flashed that to your phone, your phone is now bricked from what I can tell. T-Mobile is GSM, that HSPL looks to belong to Verizon which is CDMA. I could be wrong but if you failed to read, then obviously you really didn't need to do it. :enter sad face of choice here:
It's dead. Just put it up for sale on ebay; someone may give you 20-50 bucks for it.