Hi
Been searching through posts but couldn't find anything relating to the following hence this topic...I been trying to flash wm6.1 to this device...i had dutty's rtm 4 installed, but decided to upgrade to 6.1, however when i follow the flashing procedure (copy JumpSPL1.56-KAIS.exe to device n run it) it either gets stuck, and gives me a 262 error code then i get the tri-colour boot screen and only flashing to RUU_Kaiser_HK_WWE_1.82.721.1_radio_sign_22.51.88.13_1.27.15.32R2_Ship.exe gets the phone working again...otherwise im stuck with a tri-colour screen...when i do get stuck...i get the following on the tri-colour screen kais130
spl-1.93.0000
cpld-8
thanks
Z
so i am not the only one
to give you a little compensation you can put a new rom by using the sd
method
http://forum.xda-developers.com/showthread.php?t=336158
but please someone help
the answer isn't anywhere here cause i searched a lot
so i read wikis threads but no answer
also i can't change radios like that
Why would you jump_spl, Unless it was to solve the Hardspl issue?
Hard_Spl is the semi-permanent spl you need for flashing roms.
I have problem with my 818pro. I upgraded to WM6.1 few months ago successfully with Prophet ROM 19974 M2D. Few days ago suddenly I cant hear anything from phone, but worked well with headset. I read some posts here and try to reinstall the same software which I used few months ago to upgrade from WM5 to WM6.1(with HardSPL G4). The Installation was successful, but when it was restarted, I can only see 3 color screen and USB is written on screen also can see (IPL 2.15.0001 and SPL 2.15.0001). I tried same software few times, but the result is same. The good thing is, I am still able to connect to my PC with USB.
Now I am not able to start my PDA. Every time I restart, It will show same 3 colored screen. and If i connect to USB, it will show on screen USB.
Can Please Please someone help me how can I Install and make it working. Please give me the links as well if possible.
I will be very thankful to you..
Please Help me..
Thanks in advance
Andy
uiell
try flashing back original OS.(wm5)
http://www.htc.com/sea/
[email protected]
Seems HARDSPL not installed.
Information from you.
IPL 2.15.0001 and SPL 2.15.0001
SPL is not HARDSPL already.
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
http://forum.xda-developers.com/showthread.php?t=353547
Try to reflash with PDAVIET NoVendor
But you need to go to Bootloader Mode first ( manually). Read how to do it.
Make sure battery enough.
And flash with the ROM above.
And do the HARDSPL again.
http://forum.xda-developers.com/showthread.php?t=405384
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
Information for you : Installation, even not HARDSPL could be succesfull. But you will always stuck in Bootloader mode, like you have now.
So Reflash it first like I said and HARDSPL again.
Until SPL information like this SPL 2.G4.4PDA. Cos you have G4 Device.
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...
puhleeze? Helehehehellp me?!
noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??
*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?
goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"
Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???
Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...
Hi masters!
I'm murilo, and i'm braziliam! So, my english is soso.....rs
Well, i brick my kaiser TyTn II when i was installing "V9" Rom.
He only start on tricolor Screen!
This is the information on Screen at tricolor :
KAIS120
SPL-1.94.0000
CPLD-8
my computer Recognizes the USB connection with my HTC, and on screen of my phone appear "USB".
I can't use mtty application because appears "USB port can not open" using USB port.
Help me please, masters!
I need my phone!
Thanks!
Murilo Costa
Have you installed HardSPL? If a rom didn't succeed you can (Normally) just reinstall another rom when your in the "USB Display".
-Armazia
costa.murilo said:
Hi masters!
I'm murilo, and i'm braziliam! So, my english is soso.....rs
Well, i brick my kaiser TyTn II when i was installing "V9" Rom.
He only start on tricolor Screen!
This is the information on Screen at tricolor :
KAIS120
SPL-1.94.0000
CPLD-8
my computer Recognizes the USB connection with my HTC, and on screen of my phone appear "USB".
I can't use mtty application because appears "USB port can not open" using USB port.
Help me please, masters!
I need my phone!
Thanks!
Murilo Costa
Click to expand...
Click to collapse
This is posted in the wrong section and has nothing to do with rom development. This is not the " help me I screwed up my phone because I can't be bothered to read " section.
You have jumpspl on your phone, not hardspl. Flash your original stock rom back on your phone and then read " rom flashing for noobs " in it's entirety from the above stickies, before you really do " brick " your phone.
Please take your time to read threads before you go ahead with flashing a ROM.
[Resources] Flashing Your First Kaiser Rom (For Noobs)
To get out of the situation you are in try and flash stock ROM while in bootloader.
If you are still stuck use this thread:
Kaiser Stuck at Bootloader (aka Tri Color or Red, Green, Blue Screen)? Solutions Here
In future search before posting new thread.
Thread locked.
Hi alll,
I have orange spv m500,when i tried to update my rom it failed and got stuck in bootloader mode.And when i saw some posts they were written that 'download mtty 1.42'but in my pc on opening mtty usb option is not available Any one plzzzzzzzzzz Help I am gonna cry........
Welcome to the forums!
I suggest you read the MTTY thread very carefully!
Just follow every step and you'll be fine.
Cheers,
EC
i tried every step plzzz help me
Please tell me exactly what went wrong.
Did you fail installing the drivers?
i just tried to change my os of my pocket pc and it asked for an update for my rom and agreed for that..then after sometime when i switch on my pocket pc i said serial on top and v1.00 at the bottom....please help me .....thank you in advance
It would be very helpful if you let us know what HTC device you have