So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...
puhleeze? Helehehehellp me?!
noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??
*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?
goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"
Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???
Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...
Related
yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
araheels said:
yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
Click to expand...
Click to collapse
Try flashing it with the last WWE (non-arabic) version available for download from i-mate site.
thanks bro, i did try to flash but its not connecting, becaz its not on, when i press power button it just blink and not turned on, i am so worried, flash is done when active sync is working and the jamin is turned on, its not on
Most likely the file corrupted.
I dont know how to put Prophet in bootloader mode but can be found in forums.
Try to put the device in bootloader mode; and try to flash afterwards.
Cheers
I have the same problem after flashing with a corrupt rom. Only if i connect the JAMin to the power supply and then press and hold continuously at the camera button and press the power button once the device go to the 'boot loader mode'. But this don't help me because i have no connecting to the PC over USB.
read the forum it's written how you can put it on boot loader mode or you can try to hard reset
I don't find this post .
I try the hard reset but they dont't help.
I don't come in the boot loader mode, only if i connect the device to the power supply it works but now i haven't a connecting to the PC.
If i not connected to the power suppley and press now and hold continuously at the camera button and press the power button once there is now boot loader i see only for one moment
a white screen and also for one moment the blue light in the speaker
can i do not install the rom from my sd-cart ???
have anybody the image from JAMin ??
I have the same problem
Did you find solution ?
Forget about power button.
Press camera button. While holding it use the stylus to softreset. Take the stylus out but hold the camera button pressed. In less than 5 seconds, you will enter bootloader screen.
Hope it works.
You must put your device on to bootloader mode, how? Press the camera and the coomon manager (at the same time) put your stylus into the whole (as you made a normal soft reset) put your stylus out of the device but not the camera and the common manager botton, just a couple seconds after.
Don't be affraid is your device creen become with three colors, is normal nad the typical signal is on to bootloader mode. Now is time to find a JAMin ROM in the club imate web (if you are a member) or here in a ftp.
Tell us if you can fixed the problem.
jamin no boot
dear freind
try to connect the power supply to the cabel to enter to the bootmode and try to do software (i have same problem after flashin the jamin by kjam rom )
SAME PROBLEM AFTER DOWNGRADE CAN SOME ONE POSTE NEW ROM FOR THE IMATE JAMIN
probleme solved who want to know how to solve problem pm me
Any idea?
Do you have the solution???
Thanks
hi im having the same problem can u please inform me how u solved it, as im loosing the bootloader screen when ever i unplug it from the power.
buying a cradle will do the job
Jamin flash error
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Try this
Take a look at this thread - I think you are having the same problem as PianoSam
http://forum.xda-developers.com/showthread.php?t=300356
lordlinus said:
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Click to expand...
Click to collapse
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
lordlinus said:
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
Click to expand...
Click to collapse
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
No
It's in the link - just download it from there!!!!!!
lordlinus said:
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
Click to expand...
Click to collapse
hi there
i am using imate jamin da problem with my cell is
i upgraded my rom to qtek 2.20000 it was working absolutely fine with 8 icons in my comm manager then i upgraded to RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-b1 and it has severely damaged my cell as my phone my phone hangs white booting it shows me the colour screen with
IPL 1.00 and SPL 2.20.0001
on the Screen
OS and GSM is not displayed
I tried rom update several times but its not working
i tried to update my rom through boot loader mode but again failed
i even tried to format my phone but it gives FAT16 format failed
I even tried to upgrade to jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 but still its not working and givng same problem
now i dont understand what to do
guys please give me Advice and solution for this g3 g4 Problem
i even tried sending my phone to service center but stupid people dont know how to solve it and they returned me back
Thanks in Advance
You have bricked your phone... You just can't install a G4 rom on a G3 phone... Different chipsets are the cause of the problem... Sorry
you mean to say its over ?????????????
there should be any way
You'll have to wait to see if Jesterz manages to produce a goldcard...
BTW a goldcard it's basicly a mem card with a rom in it that autoinstalls itself thus no need for the usb connection... This fits your case cause you don't have an active usb conection because of the driver/chip conflict...
wrong software
I have the same problem i tried to flash my g3 with jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 by mistake and it was ok until the end of process when i finich it with congratulations and bla bla my device stills in the bootloader mode all the time. I can now connect and start to flash but when it comes to 80% of the process it stops with error 360 wrong command. Pleas is there any help for some kind of downgrade flash or so because it can only get boootloader but never start with software. When I try with jesters RUU-Prophet-g3-AKU2.2-2.20-2.47.21-Jester-r1 the whole process finish ok but the phone stills in bootloader. The same thing is also with RUU-Prophet-g4-AKU2.2-2.20-2.47.21-Jester-r1 I can not execute step2
that's why you should read the "sticky" first before you do it.
I have a Dopod 818Pro from a friend of mine but in Chinese ROM, so I have to read a whole nite the sticky and found out what is my Dopod version, finally I found it is G3, so I did all the steps, from unlocked the CID till upgrade to Jester latest ROM for G3 and skip the G4.
please help
Yes i realy know that it was my fault and my big mistake so i vould not do it again but now i need help because it stills in bootloader i i can even start flashing the device that gives me hope that some kind of recovery is maybe possible.
Yes i also commited this mistake its my fault but i really need help my device still enters into bootloader mode.
ur problem
there is nothing to do anymore u have to wait u CANT DO ANYTHING ITS OVER
how do you mean it is over. Do you think that could not repair it. Is it possible with sd card or jesters gold card and how. Help me please if somebody knows
there must b some way to overcome this problem
jesterz's gold card isn't working yet, and for now it's only for G3...
My hardware is G3 but flashed by mistake with G4 and now is in bootloader mode so i can start flashing but i do not know with what and how. Could you please explain me how and where can i find and use goldcard for g3 if possible Thanks
have u tried holding the camera button while softreset and then flash rom again
Yes sure i tried to flash rom from jesters for g3 which is for my device instead jesterz g4 what i used by mistake and it passed ok but when i restart it stills in bootloader mode only, so i could flash but do not know which firmware should i use
i've the same symptomes as mjankovic and aarif_ziaee, (bricked my phone)
but the only things i think i've forgot, is to cid unlock my device before doing the step 2
i have a question.
i have the rom PDAMobiz_Prophet_WM5AKU3.3_v3301
(witch is not an auto installable tile, it's a folder containing exe, dll, bat and nb file)
is it possible to install it by using teraterm pro or mtty? (connected and install bats and cabs by thoses software)
ps : i'm sorry for my bad english, i'm french not going to my languages faculty since i'have bricked my phone. need to fix it soon !
i am newbie, i using PROPHET WM6 Rom Kitchen-Simplified Core. my prophet cannot start the wm6 after i flash it again. the usb cable, also cannot detected. i try with RUU_Prophet_220734_2207114_024721_NVID to flash also cant. is that need need other software to do it in WM6?? last time i try it in WM5 can.
please help, my pda cannot start bcoz not complete flash.
Look on the forum for DUMPING from SD CARD. Maybe somebody has a rom image copied to a SD and can send it to you so you can load it.
Don't know much about it but heard about that somewhere
RespecT!
please check the same story before
did you unlock CID?????????????//
what IPL SPL do you have? g3 or g4
where the flash stop at 95% ???
i using G4. just and erro happen after flash. then try reset my pda, but stuck and cant use again.
what IPL SPL do you have, and what ROm you try to install?
you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
worked for me.
paradis_pal said:
what IPL SPL do you have, and what ROm you try to install?
Click to expand...
Click to collapse
IPL : 2.15.0001
SPL : 2.20.0001
GSM : 02.47.21
OS : 10.2.0.8
i try to install PROPHET WM6 Rom Kitchen-Simplified Core.
Downloadn at http://forum.xda-developers.com/showthread.php?t=309057
1st time i flash is ok. then i try with other setting at buildOS and flash again.
After flash i hard reset it. And it stuck at the after the screen can see IPL and SPL, the screen just show in white color at all... please help...
3 days already still dint got solution.
all pro pls help....
ahdu said:
3 days already still dint got solution.
all pro pls help....
Click to expand...
Click to collapse
Can you get back to wm5 by flashing official exe file?
If possible, do that first.
Before you try to upgrade to wm6, determine if you have G3 or G4 device. (wiki info will tell you how)
Use this file (PDAviet step 1 file) as your step 1 file, NO OTHER:
http://forum.xda-developers.com/showthread.php?t=308266
Use the upgrade utility exe for G3 OR G4, in that extracted file.
geoz67 told you great advice: you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
Let us know what you try exactly, if problem continues, to help you sort this out.
DeviLduck said:
Can you get back to wm5 by flashing official exe file?
If possible, do that first.
Before you try to upgrade to wm6, determine if you have G3 or G4 device. (wiki info will tell you how)
Use this file (PDAviet step 1 file) as your step 1 file, NO OTHER:
http://forum.xda-developers.com/showthread.php?t=308266
Use the upgrade utility exe for G3 OR G4, in that extracted file.
geoz67 told you great advice: you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
Let us know what you try exactly, if problem continues, to help you sort this out.
Click to expand...
Click to collapse
alredy settle. thanks so much...
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Load IPL/SPL from SD card ?
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
destombes_chris said:
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
Click to expand...
Click to collapse
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
illi said:
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
Click to expand...
Click to collapse
I did it a few times : I'm asked to press the zero key, press it, can see the i-mate screen during 1 second, a white screen during 1 second, and then the bootloader 3 colours...
Profy_X said:
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
Click to expand...
Click to collapse
These tools need to communicate between the PC and the phone, and I can't right now.
destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
The diff IPL SPL if I'm not wrong, have to do with the RADIO, someone correct me if I am wrong.
destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
sharedworld said:
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
Click to expand...
Click to collapse
No, as of now, no luck... but I don't give up !
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Please need some help ( a lot)
beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+
too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark
Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull
dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.
back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...
ok, will send the s200 to the SAT (repair). I don´t have other options.