Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Load IPL/SPL from SD card ?
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
destombes_chris said:
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
Click to expand...
Click to collapse
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
illi said:
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
Click to expand...
Click to collapse
I did it a few times : I'm asked to press the zero key, press it, can see the i-mate screen during 1 second, a white screen during 1 second, and then the bootloader 3 colours...
Profy_X said:
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
Click to expand...
Click to collapse
These tools need to communicate between the PC and the phone, and I can't right now.
destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
The diff IPL SPL if I'm not wrong, have to do with the RADIO, someone correct me if I am wrong.
destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
sharedworld said:
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
Click to expand...
Click to collapse
No, as of now, no luck... but I don't give up !
Related
i am newbie, i using PROPHET WM6 Rom Kitchen-Simplified Core. my prophet cannot start the wm6 after i flash it again. the usb cable, also cannot detected. i try with RUU_Prophet_220734_2207114_024721_NVID to flash also cant. is that need need other software to do it in WM6?? last time i try it in WM5 can.
please help, my pda cannot start bcoz not complete flash.
Look on the forum for DUMPING from SD CARD. Maybe somebody has a rom image copied to a SD and can send it to you so you can load it.
Don't know much about it but heard about that somewhere
RespecT!
please check the same story before
did you unlock CID?????????????//
what IPL SPL do you have? g3 or g4
where the flash stop at 95% ???
i using G4. just and erro happen after flash. then try reset my pda, but stuck and cant use again.
what IPL SPL do you have, and what ROm you try to install?
you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
worked for me.
paradis_pal said:
what IPL SPL do you have, and what ROm you try to install?
Click to expand...
Click to collapse
IPL : 2.15.0001
SPL : 2.20.0001
GSM : 02.47.21
OS : 10.2.0.8
i try to install PROPHET WM6 Rom Kitchen-Simplified Core.
Downloadn at http://forum.xda-developers.com/showthread.php?t=309057
1st time i flash is ok. then i try with other setting at buildOS and flash again.
After flash i hard reset it. And it stuck at the after the screen can see IPL and SPL, the screen just show in white color at all... please help...
3 days already still dint got solution.
all pro pls help....
ahdu said:
3 days already still dint got solution.
all pro pls help....
Click to expand...
Click to collapse
Can you get back to wm5 by flashing official exe file?
If possible, do that first.
Before you try to upgrade to wm6, determine if you have G3 or G4 device. (wiki info will tell you how)
Use this file (PDAviet step 1 file) as your step 1 file, NO OTHER:
http://forum.xda-developers.com/showthread.php?t=308266
Use the upgrade utility exe for G3 OR G4, in that extracted file.
geoz67 told you great advice: you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
Let us know what you try exactly, if problem continues, to help you sort this out.
DeviLduck said:
Can you get back to wm5 by flashing official exe file?
If possible, do that first.
Before you try to upgrade to wm6, determine if you have G3 or G4 device. (wiki info will tell you how)
Use this file (PDAviet step 1 file) as your step 1 file, NO OTHER:
http://forum.xda-developers.com/showthread.php?t=308266
Use the upgrade utility exe for G3 OR G4, in that extracted file.
geoz67 told you great advice: you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
Let us know what you try exactly, if problem continues, to help you sort this out.
Click to expand...
Click to collapse
alredy settle. thanks so much...
Guys,
I wonder if you can help. I have trawled this and many other forums and found many people that are having problems with their HTC Prophet or variations of the same device.
I have the Orange SPV M600, it was in my pocket and when I took it out to turn it on, it was displaying the bootloader screen after seemingly soft resetting itself. It is displaying the tri-colour bootloader with the following IPL/SPL
- IPL 2.10.0001 - SPL 2.10.0001
I have tried the following things that I have found in the forums:
1. Taking the battery out for 10 minutes ~ Still the same.
2. Hard Reset ~ I get the "Press SEND button to factory restore" message
but nothing happens when I push the call button.
3. Reflashing the ROM ~ I am unable to do this. I only have Vista and
WMDC does not see the phone in bootloader mode.
Is the phone dead? If so how could this have happened?
If anyone could help I would be eternally greatful. Oh and to add another complication the phone is still CID Locked
Thanks in advance
Barry
well if you where is south africa i would of helped you im sure if you have it runing on xp it will work my jamin did the same and all i did was push the camera button and reseted it got into tri colour mode and reflashed it
sorry that i could not help you but like i said if you in SA we could of tried it on my mashine
Any progress ?
did you ever get this sorted out ? Surely all you're gonna need is a PC with XP and active sync....
If I was closer you could have sent the phone to me and I would have had a go at reflashing the rom, but I'm at the other end of the country....
Hello guy here is a solution to flash under vista i have too a orange m600 and it works fine
http://www.modaco.com/RUU-Vista-done-u-t252977.html
help stuck on the bootlader screen?
guyz i have a jamin.. my cousin was flashin it and flashed the wrong software.. if i reset the phone it shows the boat loader screen!! and i cnat do anythin..caz u tell me which slftware to flash..and how to do it?? My freind told me all solution to my problem's will be solved here
hopin i will get my solution
First of all, download the NVID (no vender) AKU2.2 from here. http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Then, open activesync, select connection settings and UNCHECK the connect through USB option.
Then run the NVID file. It will take a while, and may seem to get stuck at 80% or 95%. Just leave it alone.
When that's done, you can either use it as it is, or load anyother ROM you want.
i have a bit similar problem
can some one plese guide me how to flash it with xp?????
Regards
First get a version of ActiveSync, any will do, but more recent is probably better. Then download the ROM (see above). In ActiveSync>Connection Settings uncheck the Connect through USB option. Then connect the Prophet.
Next Unzip the NVID file, and run RUU_PROPHET... This will flash your Prophet with a very basic ROM. If you then want to upgrade to a different ROM follow these steps: http://forum.xda-developers.com/showthread.php?t=310452
hi, guys, i tried to unlock a kaiser with htc all unlock 1.2, and in the pass number 3, show me an error, and put the screen black, when i conect to sync, it shows conected, but the screen is black, if i pull out and in the battery, and turn on, shows the att and 3g logos, and then again the screen turns black.
please if somebody can help me, i'm new with htc, but it shows this:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
Thanks in advance for you help.
it is getting worst, i did a hard reset, and now when i conect to my computer, ask me for "generic rndis drivers", last time i solve this from the phone, but now it has black screen.
Please i need yor help.
thanks.
cellshop2 said:
hi, guys, i tried to unlock a kaiser with htc all unlock 1.2, and in the pass number 3, show me an error, and put the screen black, when i conect to sync, it shows conected, but the screen is black, if i pull out and in the battery, and turn on, shows the att and 3g logos, and then again the screen turns black.
please if somebody can help me, i'm new with htc, but it shows this:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
Thanks in advance for you help.
it is getting worst, i did a hard reset, and now when i conect to my computer, ask me for "generic rndis drivers", last time i solve this from the phone, but now it has black screen.
Please i need yor help.
thanks.
Click to expand...
Click to collapse
You have a patched Radio on your device that was put on to unlock it. Unfortunately the Radio is incompatible with your rom which is giving you the black screen. Do you know if you have WM6.0 or WM6.1? If you do then you can just flash a compatible Radio back onto your device via microSD Card.
The simplest thing if you dont know what Rom you are using and dont have any user information on your phone that you need to keep, or if you already have it backed up is to goto my Flashing Your First Rom Guide, upgrade your HardSPL using step3 (Flashing via MicroSD Card) and then flash a WM6.1 Rom using step5. Once you have upgraded your Rom you should have no problem using step4 to unlock your device if you want to. Just remember to flash back a WM6.1 Radio (step6) after it has completed.
What is "htc all unlock 1.2".
I can't find that tool on xda-developers.
Dave
DaveShaw said:
What is "Flashing via MicroSD Card".
I can't find that tool on xda-developers.
Dave
Click to expand...
Click to collapse
Dave what did I tell you about following me around lol
mskip said:
Dave what did I tell you about following me around lol
Click to expand...
Click to collapse
LOL
Yeah, sound's like a new radio flash will sort it out.
Why use a Unlocker off one forum and ask for help on another? There are 3 Kaiser unlockers on here All of which are really easy to use and work perfectly (or we know howto fix when they go wrong).
Ta
Dave
Turn's out your using Olipro's unlocker.
Just that the bastards on the other site didn't credit him for it
@OP - Please see this thread for more help - http://forum.xda-developers.com/showthread.php?t=375583
Ta
Dave
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...
puhleeze? Helehehehellp me?!
noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??
*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?
goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"
Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???
Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Please need some help ( a lot)
beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+
too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark
Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull
dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.
back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...
ok, will send the s200 to the SAT (repair). I donĀ“t have other options.