Database Info

My Prophet (Jamin) Upgrading Problem

yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks

araheels said:
yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
Click to expand...
Click to collapse
Try flashing it with the last WWE (non-arabic) version available for download from i-mate site.

thanks bro, i did try to flash but its not connecting, becaz its not on, when i press power button it just blink and not turned on, i am so worried, flash is done when active sync is working and the jamin is turned on, its not on

Most likely the file corrupted.
I dont know how to put Prophet in bootloader mode but can be found in forums.
Try to put the device in bootloader mode; and try to flash afterwards.
Cheers

I have the same problem after flashing with a corrupt rom. Only if i connect the JAMin to the power supply and then press and hold continuously at the camera button and press the power button once the device go to the 'boot loader mode'. But this don't help me because i have no connecting to the PC over USB.

read the forum it's written how you can put it on boot loader mode or you can try to hard reset

I don't find this post .
I try the hard reset but they dont't help.
I don't come in the boot loader mode, only if i connect the device to the power supply it works but now i haven't a connecting to the PC.
If i not connected to the power suppley and press now and hold continuously at the camera button and press the power button once there is now boot loader i see only for one moment
a white screen and also for one moment the blue light in the speaker
can i do not install the rom from my sd-cart ???
have anybody the image from JAMin ??

I have the same problem
Did you find solution ?

Forget about power button.
Press camera button. While holding it use the stylus to softreset. Take the stylus out but hold the camera button pressed. In less than 5 seconds, you will enter bootloader screen.
Hope it works.

You must put your device on to bootloader mode, how? Press the camera and the coomon manager (at the same time) put your stylus into the whole (as you made a normal soft reset) put your stylus out of the device but not the camera and the common manager botton, just a couple seconds after.
Don't be affraid is your device creen become with three colors, is normal nad the typical signal is on to bootloader mode. Now is time to find a JAMin ROM in the club imate web (if you are a member) or here in a ftp.
Tell us if you can fixed the problem.

jamin no boot
dear freind
try to connect the power supply to the cabel to enter to the bootmode and try to do software (i have same problem after flashin the jamin by kjam rom )

SAME PROBLEM AFTER DOWNGRADE CAN SOME ONE POSTE NEW ROM FOR THE IMATE JAMIN
probleme solved who want to know how to solve problem pm me

Any idea?
Do you have the solution???
Thanks

hi im having the same problem can u please inform me how u solved it, as im loosing the bootloader screen when ever i unplug it from the power.
buying a cradle will do the job

Jamin flash error
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks

Try this
Take a look at this thread - I think you are having the same problem as PianoSam
http://forum.xda-developers.com/showthread.php?t=300356
lordlinus said:
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Click to expand...
Click to collapse

flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse

The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
lordlinus said:
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
Click to expand...
Click to collapse

flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse

No
It's in the link - just download it from there!!!!!!
lordlinus said:
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
Click to expand...
Click to collapse

Please Help! My JAMin is dead!

help... i downloaded smart1's (normal, not clean) update, and launched UPGRADE_ROM.DAT from PC... it said initializing and everything... and then it reached to "copying something.dll' ... i waited 10 minutes or so then i got something like:
"error cant copy ....... because connection closed from remote... something like that."
i did NOT touch the imate during the process
and now when i turn on my imate i get the HTC with white background for a second but then it freezes on the blue "i-mate" screen... displaying:
IPL 2.13.0001
SPL 2.13.0001
GSM 02.20.21
OS 10.1.0.811
when i connect it to pc, windows does recognise and install my device but ActiveSync doesnt connect.
i tried removing the battery then putting it back in then pressing and holding the conn. button along with the power button and i DO get to the bootloader screen (with three colors) and then when i plug in the usb i get a small 'usb' word at the bottom of the screen, but still, ActiveSync doesnt connect... i tried installing the update again... but the program doesnt find my device
how can i make it work again ??? plz help me
thx in advance

Now you need to find a rom that will install from bootloader mode and not an update........
I don't think you phone is dead
JD

johnnyduk said:
Now you need to find a rom that will install from bootloader mode and not an update........
I don't think you phone is dead
JD
Click to expand...
Click to collapse
i read in another topic what u said above... thx for ur reply...
btw, i'm currently downloading a 56 mb file called:
JAMin_WWE_2130923_21309112_020720_ship.zip
it can be downloaded from:
ftp://ftp.clubimate.com/JAMin_WWE_2130923_21309112_020720_ship.zip
or (better direct link)
http://www.clubimate.com/support/JAMMIN/ROM/JAMin_WWE_2130923_21309112_020720_ship.zip
i suppose this is the file i shoudl install right now using bootleader mode ? right ?
my previous rom version was 2.13.9.23 (same as name of file)
so is this the file i shud be downloading right now ?
thx a lot in advance

Just BEWARE that the rom you download is for your phone, it will be for a G3 or a G4, if you get it wrong, your phone is DEAD.
Please read the wiki and stickies....................................
JD

please. my phone doesnt move. it stuck on login screen.:
any way to restore it? i tried to hard reset, soft reset...nothing..
i tried to install smart 1 and after this happened

Problem solved
Same problem for me, but I solved today:
I connected the phone to pc in bootloader mode, the pc see the phone and says ppc usb sync, but the activesync not started.
I tried to install a qtek official rom by dangaard (you can find it here: http://www.megaupload.com/it/?d=4ELWL078 ) and I solded the problem !
Thanks god!!!!

Please i have the same issue with my O2 XDA Neo - G4, i checked the official site but i don't understand german. Pls someone paste me a link to official Rom.

Twinsis said:
Please i have the same issue with my O2 XDA Neo - G4, i checked the official site but i don't understand german. Pls someone paste me a link to official Rom.
Click to expand...
Click to collapse
ftp://ftp.clubimate.com/JAMin_WWE_213923_2139123_022021_ship.zip
here is the official link for O2 xda or Imate Jamin

Same problem!
I had same problem but in my case with downgrade from WM6 to ASERG rom, i have downloaded RUU_Prophet_220734_2207114_024721_NVID.exe and that fixed my problem.

Stuck in the bootloader

Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.

Load IPL/SPL from SD card ?
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.

destombes_chris said:
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
Click to expand...
Click to collapse
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!

try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again

illi said:
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
Click to expand...
Click to collapse
I did it a few times : I'm asked to press the zero key, press it, can see the i-mate screen during 1 second, a white screen during 1 second, and then the bootloader 3 colours...

Profy_X said:
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
Click to expand...
Click to collapse
These tools need to communicate between the PC and the phone, and I can't right now.

destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
The diff IPL SPL if I'm not wrong, have to do with the RADIO, someone correct me if I am wrong.

destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...

sharedworld said:
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
Click to expand...
Click to collapse
No, as of now, no luck... but I don't give up !

Qtek S200 G3, flashed with G4 , please heelp!

So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes

noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.

noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?

noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...

puhleeze? Helehehehellp me?!

noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....

you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)

marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.

noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??

*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..

marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas

did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...

marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.

noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?

goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?

If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .

thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"

Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???

Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...

Stuck en bootloader

Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)

Please need some help ( a lot)

beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and

Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??

beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+

too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark

Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull

dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?

noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.

back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...

ok, will send the s200 to the SAT (repair). I don´t have other options.