yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
araheels said:
yesterday i got Jamin but wid old rom
i downloaded the latest unbranderd dopod rom from ftp.xda-devel....
but after completion of all updating my jamin is no longer starts
it is just blinking
screen flashs and didnt disply any thing
i am soo worried plz any body help meeee
i think there is something wrong wid bootloader,
any body knows
plz help
thanks
Click to expand...
Click to collapse
Try flashing it with the last WWE (non-arabic) version available for download from i-mate site.
thanks bro, i did try to flash but its not connecting, becaz its not on, when i press power button it just blink and not turned on, i am so worried, flash is done when active sync is working and the jamin is turned on, its not on
Most likely the file corrupted.
I dont know how to put Prophet in bootloader mode but can be found in forums.
Try to put the device in bootloader mode; and try to flash afterwards.
Cheers
I have the same problem after flashing with a corrupt rom. Only if i connect the JAMin to the power supply and then press and hold continuously at the camera button and press the power button once the device go to the 'boot loader mode'. But this don't help me because i have no connecting to the PC over USB.
read the forum it's written how you can put it on boot loader mode or you can try to hard reset
I don't find this post .
I try the hard reset but they dont't help.
I don't come in the boot loader mode, only if i connect the device to the power supply it works but now i haven't a connecting to the PC.
If i not connected to the power suppley and press now and hold continuously at the camera button and press the power button once there is now boot loader i see only for one moment
a white screen and also for one moment the blue light in the speaker
can i do not install the rom from my sd-cart ???
have anybody the image from JAMin ??
I have the same problem
Did you find solution ?
Forget about power button.
Press camera button. While holding it use the stylus to softreset. Take the stylus out but hold the camera button pressed. In less than 5 seconds, you will enter bootloader screen.
Hope it works.
You must put your device on to bootloader mode, how? Press the camera and the coomon manager (at the same time) put your stylus into the whole (as you made a normal soft reset) put your stylus out of the device but not the camera and the common manager botton, just a couple seconds after.
Don't be affraid is your device creen become with three colors, is normal nad the typical signal is on to bootloader mode. Now is time to find a JAMin ROM in the club imate web (if you are a member) or here in a ftp.
Tell us if you can fixed the problem.
jamin no boot
dear freind
try to connect the power supply to the cabel to enter to the bootmode and try to do software (i have same problem after flashin the jamin by kjam rom )
SAME PROBLEM AFTER DOWNGRADE CAN SOME ONE POSTE NEW ROM FOR THE IMATE JAMIN
probleme solved who want to know how to solve problem pm me
Any idea?
Do you have the solution???
Thanks
hi im having the same problem can u please inform me how u solved it, as im loosing the bootloader screen when ever i unplug it from the power.
buying a cradle will do the job
Jamin flash error
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Try this
Take a look at this thread - I think you are having the same problem as PianoSam
http://forum.xda-developers.com/showthread.php?t=300356
lordlinus said:
Hello guys,
I tried to upgrade my Jamin to WM6 and now it dosent load at all so i wanted to go back to original ROM from Jamin but now it says "This NBF file cannot be used for your PDA phone.Please get newer NBF file."
also, previous used to have IMATE logo and now it displays QteK logo and freezes displaying
IPL 1.00
SPL 2.20.0000
GSM 02.47.21
OS 10.2.0.8
Can someone please help me how to get back to WM5 or WM6.
Thanks
Click to expand...
Click to collapse
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
lordlinus said:
flykthewiz said:
Take a look at this thread - I think you are having the same problem as PianoSam
Thanks flyktewiz,
I did exactly what was told in the thread mention, but now while installing i get the below error
" Error[238]: File Read
The Update Utility can not open the requested file.Please check your Update Utility."
I have closed all the programs that i was using re-started, but still i get this error.
I then tried following http://forum.xda-developers.com/showthread.php?t=291215
and used ROMUpdateUtility_Wizard_NoID.exe instead of the original ROMUpdateUtility.exe and now i get
Error [300]: Invalid Update tool
This update utility cannot be used for your PDA Phone.Please get newer Update Utility
Click to expand...
Click to collapse
Click to expand...
Click to collapse
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
No
It's in the link - just download it from there!!!!!!
lordlinus said:
flykthewiz said:
The thread has been updated to include Update tools for G4 and G3 that worked for Pianosam - have a look and give the appropriate one a try
http://forum.xda-developers.com/showthread.php?t=300356&page=2
Thanks for the help, Can you please re-post RUU.ZIP files (or just a link)
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Related
Hi there,
I bought a Qtek S200 and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully the phone has become locked in the boot loader screen. I have done both soft reset and hard reset. Nothing works. The phone gets locked in the boot loader screen. Need help.
Thanks,
Julian
Try to reflash with Qtek ROM instead...
Why you said that it's locked on the Bootloader screen?
Is it frozen or locked?
Hi Rayan,
I tried flashing with the Qtek ROM. I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there. Nothing else happens. I have sent the device back to the guy from whom I bought it.
I got the same problem as Julian - I tried to upgrade with the mentioned ROM and now my device are stucked at the boot screen :?
Some help here ? I'm in same situation
I have an O2 with Dopod rom, after I instaled some software I must to restart and then my O2 are stucked/frozen on Windows Mobile splash screen
Only if I remove the battery I can stop the pda.
I can't do nothing to make him to start. Some ideea ?
:shock:
Later Edit :
solved with http://forum.xda-developers.com/viewtopic.php?t=49298&sid=35f5c1e9e165997b4634ea0c7700ac76
Same issue here with a O2 Xda Neo with German Rom.
Applied the procedure of the prophet wiki : How to CID unlock and Upgrade your Prophet (SPL 2.09 & 2.15)
After step 6 and a soft rest it is stuck in bootloader and will not do anything else, not even off or hard reset...battey has to be removed in order to shut it off....
Any ideas?
Remind me to find the guy who wrote the wiki page on unlocking CID in Prophet......good job pal......
Aaaaarggghhhh %^*^%*^%*^%*
Problem solved..
Hi everyone,
Good news at last. I sent my Qtek S200 to the guy from whom I bought the phone. He fixed it and now I am a happy man. You can check with him if everything else fails. Email him at E gadget Depot ( [email protected]).
All the best..
i tried to upgrade my QTEK S200 with this RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip it got to 95% and then it gives me nbf file cannot work with your PDA. Please help.
I have this problem too, i know only one exit from this situation - i have flash my s200 with RUU_215737_2157135_023021_QTEK_s200_RUS ROM, now it work fine.
you find it her
bootloader issue
I have the same problem too, If anybody know method to fix this problem please help us.
I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there.
THX in advance for you help
Robert
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Please, the links to the solution does not exists anymore.
I need help!!
Qtek S200 stuck in tri-color screen, all flashing so far still does not make it work..
When doing a hard reset I get format failed.
/Jonas
I have same problem!
Anyone can help?
TJSM said:
I have same problem!
Anyone can help?
Click to expand...
Click to collapse
Go to HMA4's upgrade guide or my thread in my signature...
same problem
i have exactly same problem and i couldnt solve it too.So can someone help us?
Please someone explain completely what should we do.
i can not active sync and waiting on the bootloader screen
bacardilima said:
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Click to expand...
Click to collapse
daelee,
you can get normal state, follow the bolded attention at above quote.after entering the 3 colour screen connect USB and you can load the original WM5 ROM on your device. after that, upgrade to any wm6 by the rules and active sync.
the link is dead on that message..
i went to the that page and the link for solution is dead.
http://forum.xda-developers.com/showthread.php?t=376561
find out is there anything that can help!
help... i downloaded smart1's (normal, not clean) update, and launched UPGRADE_ROM.DAT from PC... it said initializing and everything... and then it reached to "copying something.dll' ... i waited 10 minutes or so then i got something like:
"error cant copy ....... because connection closed from remote... something like that."
i did NOT touch the imate during the process
and now when i turn on my imate i get the HTC with white background for a second but then it freezes on the blue "i-mate" screen... displaying:
IPL 2.13.0001
SPL 2.13.0001
GSM 02.20.21
OS 10.1.0.811
when i connect it to pc, windows does recognise and install my device but ActiveSync doesnt connect.
i tried removing the battery then putting it back in then pressing and holding the conn. button along with the power button and i DO get to the bootloader screen (with three colors) and then when i plug in the usb i get a small 'usb' word at the bottom of the screen, but still, ActiveSync doesnt connect... i tried installing the update again... but the program doesnt find my device
how can i make it work again ??? plz help me
thx in advance
Now you need to find a rom that will install from bootloader mode and not an update........
I don't think you phone is dead
JD
johnnyduk said:
Now you need to find a rom that will install from bootloader mode and not an update........
I don't think you phone is dead
JD
Click to expand...
Click to collapse
i read in another topic what u said above... thx for ur reply...
btw, i'm currently downloading a 56 mb file called:
JAMin_WWE_2130923_21309112_020720_ship.zip
it can be downloaded from:
ftp://ftp.clubimate.com/JAMin_WWE_2130923_21309112_020720_ship.zip
or (better direct link)
http://www.clubimate.com/support/JAMMIN/ROM/JAMin_WWE_2130923_21309112_020720_ship.zip
i suppose this is the file i shoudl install right now using bootleader mode ? right ?
my previous rom version was 2.13.9.23 (same as name of file)
so is this the file i shud be downloading right now ?
thx a lot in advance
Just BEWARE that the rom you download is for your phone, it will be for a G3 or a G4, if you get it wrong, your phone is DEAD.
Please read the wiki and stickies....................................
JD
please. my phone doesnt move. it stuck on login screen.:
any way to restore it? i tried to hard reset, soft reset...nothing..
i tried to install smart 1 and after this happened
Problem solved
Same problem for me, but I solved today:
I connected the phone to pc in bootloader mode, the pc see the phone and says ppc usb sync, but the activesync not started.
I tried to install a qtek official rom by dangaard (you can find it here: http://www.megaupload.com/it/?d=4ELWL078 ) and I solded the problem !
Thanks god!!!!
Please i have the same issue with my O2 XDA Neo - G4, i checked the official site but i don't understand german. Pls someone paste me a link to official Rom.
Twinsis said:
Please i have the same issue with my O2 XDA Neo - G4, i checked the official site but i don't understand german. Pls someone paste me a link to official Rom.
Click to expand...
Click to collapse
ftp://ftp.clubimate.com/JAMin_WWE_213923_2139123_022021_ship.zip
here is the official link for O2 xda or Imate Jamin
Same problem!
I had same problem but in my case with downgrade from WM6 to ASERG rom, i have downloaded RUU_Prophet_220734_2207114_024721_NVID.exe and that fixed my problem.
i have tired v3 wm6 update and..after the update my screen is stuck...at o2 sign..with bubbles,, the four red words appear on the screen but doesn't change anything...
i'd like to reflash back but it doesn't seem like connecting to PC via USB..
what do i do...?
and i found..
it just stopps in the boot loader mode and turns to black screeen .. and that's it...
I cna't even connect to USB so which means i can't flash back to normal..
is there any suggestions??
like resseting back up?
I have tried soft and hard reset but both don't seem to work.. still stuck in the bootloader mode....
What do I DO>>>>>>>>>>>>>....please help me...><
Try to Enter Bootloader:
Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
However, you have to write in the right post, i guess you mean the Ohlala_WWE_WM6_v3 ROM. If you had read the entire post youl'd know that this one is bad. V4 should solve the problem.
thanks for your answer !!but..
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
llvll said:
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
Click to expand...
Click to collapse
You cannot use "upgrade_rom.bat" to flash ur device with RGB screen. The bat file is for upgrade, not for fresh install. It means that you have to install AKU2.xx NVID.exe (executable) first. The .exe file can recognize ur device via RGB screen.
After reset ur device with AKU2.x and successfully connect to the PC vis Activesync, you then can run upgrade_rom.bat.
And... don't be too panic. You have to read more.
thank you so much !!
i' ll try it right now !! omg ...i'm so relived that I got an answer !!!
you are the best!
um...
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
llvll said:
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
Click to expand...
Click to collapse
here http://www.4shared.com/file/12240109/ca99469a/RUU_Prophet_220734_2207114_024721_NVID.html
thanks !!!
is there an o2 version of NVID??? anywhere? i've just installed this but it says Qteck..
No it's a Qteck ROM not an O², I don't know if there is a 2.20 NVID ROM from O² here, sorry.
i've just installed AKU...thing
after installing AKU...
my phone doesn't seem like it can connect to Antisync program..
is there any reason why..this is happpenin..?
make hard reset after flash firmware!
yese !!
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
you could try this. Someone else posted it here, and when my phone stopped connecting after some update it fixed activesync. It's a switch.
llvll said:
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
Click to expand...
Click to collapse
Had O2 ever released HTC Prophet?
Sorry but I'm not O2 fan.
I have only Prophet so I know only Prophet.
You could go to the right thread for ur device O2 and look for the right .exe file.
PS: is it XDA Neo? If it is Prophet it should be OK.
Try holding Camera+Comm buttons during pressing reset button ur device will ask u to Format something. Press send button (green phone button) and try again.
Safe
Thanks guys, you saved my S200
Matos
Ohyea !!
I found the solution !!! dat Qteck one worked but um....
yea and my phone is Xda Neo !!!
the black one !
thanks for all the replies guys !!!!!!!
Whoohoo, thanx for mentioning the bootloader mode (by only holding the camera button ) Now I can try another WM6 rom, which does work I hope
hello there same problem here.. mine is also xda neo.. when trying to upgrade wm6 it stuck exactly same as yours..how did u fix the problem? thanx for ur advice
i am newbie, i using PROPHET WM6 Rom Kitchen-Simplified Core. my prophet cannot start the wm6 after i flash it again. the usb cable, also cannot detected. i try with RUU_Prophet_220734_2207114_024721_NVID to flash also cant. is that need need other software to do it in WM6?? last time i try it in WM5 can.
please help, my pda cannot start bcoz not complete flash.
Look on the forum for DUMPING from SD CARD. Maybe somebody has a rom image copied to a SD and can send it to you so you can load it.
Don't know much about it but heard about that somewhere
RespecT!
please check the same story before
did you unlock CID?????????????//
what IPL SPL do you have? g3 or g4
where the flash stop at 95% ???
i using G4. just and erro happen after flash. then try reset my pda, but stuck and cant use again.
what IPL SPL do you have, and what ROm you try to install?
you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
worked for me.
paradis_pal said:
what IPL SPL do you have, and what ROm you try to install?
Click to expand...
Click to collapse
IPL : 2.15.0001
SPL : 2.20.0001
GSM : 02.47.21
OS : 10.2.0.8
i try to install PROPHET WM6 Rom Kitchen-Simplified Core.
Downloadn at http://forum.xda-developers.com/showthread.php?t=309057
1st time i flash is ok. then i try with other setting at buildOS and flash again.
After flash i hard reset it. And it stuck at the after the screen can see IPL and SPL, the screen just show in white color at all... please help...
3 days already still dint got solution.
all pro pls help....
ahdu said:
3 days already still dint got solution.
all pro pls help....
Click to expand...
Click to collapse
Can you get back to wm5 by flashing official exe file?
If possible, do that first.
Before you try to upgrade to wm6, determine if you have G3 or G4 device. (wiki info will tell you how)
Use this file (PDAviet step 1 file) as your step 1 file, NO OTHER:
http://forum.xda-developers.com/showthread.php?t=308266
Use the upgrade utility exe for G3 OR G4, in that extracted file.
geoz67 told you great advice: you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
Let us know what you try exactly, if problem continues, to help you sort this out.
DeviLduck said:
Can you get back to wm5 by flashing official exe file?
If possible, do that first.
Before you try to upgrade to wm6, determine if you have G3 or G4 device. (wiki info will tell you how)
Use this file (PDAviet step 1 file) as your step 1 file, NO OTHER:
http://forum.xda-developers.com/showthread.php?t=308266
Use the upgrade utility exe for G3 OR G4, in that extracted file.
geoz67 told you great advice: you could try the following:
reset the pda while holding the camera key. you should then see 3 colored stripes.
next plug in the usb cable. if the thing is not totally shot you should see the word 'usb' come on in the lower left corner.
try to flash again.
Let us know what you try exactly, if problem continues, to help you sort this out.
Click to expand...
Click to collapse
alredy settle. thanks so much...
Hello together, I want to put a WM6 ROM on my Wizard G4, but I get an error.
ERROR [300]: INVALID UPDATE TOOL
Can somebody help me please?
I made the G4 Hard SPL and have the IPL 2.21.0001 and SPL 2.21.Olip
Try using the attached RUU_MUN - this one always works for me
Just copy the image file into the same directory to run.
A credit to the community
Works a treat - thank you!
My phone is dead
After I flashed my phone with the above tool, the phone hanged on the start-up and now dead. It cannot even power on. Even when charger is fixed it does not power on at all.
Please what do I do to revive this phone?
Thanks in advance.
babyelephantt said:
After I flashed my phone with the above tool, the phone hanged on the start-up and now dead. It cannot even power on. Even when charger is fixed it does not power on at all.
Please what do I do to revive this phone?
Thanks in advance.
Click to expand...
Click to collapse
chech this
http://forum.xda-developers.com/showthread.php?t=274236
http://www.filestube.com/c15dcecb57d0222b03ea/go.html
about bootloader mode(wiza 200 bootloader mode(holding down the camera button then press the soft reset whole..
that should bring you to bootloader.. then flash!)
BR
UMER
suggestion
comec said:
Hello together, I want to put a WM6 ROM on my Wizard G4, but I get an error.
ERROR [300]: INVALID UPDATE TOOL
Can somebody help me please?
I made the G4 Hard SPL and have the IPL 2.21.0001 and SPL 2.21.Olip
Click to expand...
Click to collapse
hello this happened to me at least tentimes LOL so i can give advice:
juste take the NBF file from rom you wanto to upload to your WIZARD, copy it in another ROM folder (ROMS use to have their own RUU) and then just upload XD i did it as i said at least 10 times