hi there
i am using imate jamin da problem with my cell is
i upgraded my rom to qtek 2.20000 it was working absolutely fine with 8 icons in my comm manager then i upgraded to RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-b1 and it has severely damaged my cell as my phone my phone hangs white booting it shows me the colour screen with
IPL 1.00 and SPL 2.20.0001
on the Screen
OS and GSM is not displayed
I tried rom update several times but its not working
i tried to update my rom through boot loader mode but again failed
i even tried to format my phone but it gives FAT16 format failed
I even tried to upgrade to jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 but still its not working and givng same problem
now i dont understand what to do
guys please give me Advice and solution for this g3 g4 Problem
i even tried sending my phone to service center but stupid people dont know how to solve it and they returned me back
Thanks in Advance
You have bricked your phone... You just can't install a G4 rom on a G3 phone... Different chipsets are the cause of the problem... Sorry
you mean to say its over ?????????????
there should be any way
You'll have to wait to see if Jesterz manages to produce a goldcard...
BTW a goldcard it's basicly a mem card with a rom in it that autoinstalls itself thus no need for the usb connection... This fits your case cause you don't have an active usb conection because of the driver/chip conflict...
wrong software
I have the same problem i tried to flash my g3 with jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 by mistake and it was ok until the end of process when i finich it with congratulations and bla bla my device stills in the bootloader mode all the time. I can now connect and start to flash but when it comes to 80% of the process it stops with error 360 wrong command. Pleas is there any help for some kind of downgrade flash or so because it can only get boootloader but never start with software. When I try with jesters RUU-Prophet-g3-AKU2.2-2.20-2.47.21-Jester-r1 the whole process finish ok but the phone stills in bootloader. The same thing is also with RUU-Prophet-g4-AKU2.2-2.20-2.47.21-Jester-r1 I can not execute step2
that's why you should read the "sticky" first before you do it.
I have a Dopod 818Pro from a friend of mine but in Chinese ROM, so I have to read a whole nite the sticky and found out what is my Dopod version, finally I found it is G3, so I did all the steps, from unlocked the CID till upgrade to Jester latest ROM for G3 and skip the G4.
please help
Yes i realy know that it was my fault and my big mistake so i vould not do it again but now i need help because it stills in bootloader i i can even start flashing the device that gives me hope that some kind of recovery is maybe possible.
Yes i also commited this mistake its my fault but i really need help my device still enters into bootloader mode.
ur problem
there is nothing to do anymore u have to wait u CANT DO ANYTHING ITS OVER
how do you mean it is over. Do you think that could not repair it. Is it possible with sd card or jesters gold card and how. Help me please if somebody knows
there must b some way to overcome this problem
jesterz's gold card isn't working yet, and for now it's only for G3...
My hardware is G3 but flashed by mistake with G4 and now is in bootloader mode so i can start flashing but i do not know with what and how. Could you please explain me how and where can i find and use goldcard for g3 if possible Thanks
have u tried holding the camera button while softreset and then flash rom again
Yes sure i tried to flash rom from jesters for g3 which is for my device instead jesterz g4 what i used by mistake and it passed ok but when i restart it stills in bootloader mode only, so i could flash but do not know which firmware should i use
i've the same symptomes as mjankovic and aarif_ziaee, (bricked my phone)
but the only things i think i've forgot, is to cid unlock my device before doing the step 2
i have a question.
i have the rom PDAMobiz_Prophet_WM5AKU3.3_v3301
(witch is not an auto installable tile, it's a folder containing exe, dll, bat and nb file)
is it possible to install it by using teraterm pro or mtty? (connected and install bats and cabs by thoses software)
ps : i'm sorry for my bad english, i'm french not going to my languages faculty since i'have bricked my phone. need to fix it soon !
Related
HI....
for a while I had flashed the German Rom WM 6 to my wizard.
It works and Im happy with it .
But now after a complete power up it starts after a short loading (windows) directly with the password inquiry on the screen. That normaly is displayed after the screen callibration.
And I can´t type in the password and when the wizard says it is wrong.
So I tryed to flash a new image, no chance !!!
The ruu says That is not the right version or error 300 no conection when I start with the boot screen after power up and camera button.
The IPL is 2.21.0001 and
the SPL is 2.G4.4PDA
Maybe there is some help outside here
Thank you
First you identify your wizard
you have a G4 wizard and I believe that u r trying to flash with a G3 rom thats one error i can see.
second most important thing is try to hard reset your device first to come back on the normal situation and then again go through with step by step for CID unlock. which you need to flash your rom then go through with this link which you can find on Wiki also.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
then try once again
hope this solve your wizard probem
I tried to flash the old g4 rom that i have since 5 month
my prophet was working normaly and while i was installing a program it stoped. i formated it and reinstalled the windows but what happened is:
1-it doesnt recognize the memory card anymore
I thought it is rom problem , i tried to install anothere rom but THERE IS NO 3 colour screen but the prophet is working
please any body have idea about this problem reply .
have u done hardspl? try flashing another rom..
i tried hardspl but it didnt continue the process
while i was doing hardspl my prophet turnedoff
thank blusilv for reply
where is the help??????????????
Listen up
First off all charge the battery for 2 hours before doing this.
After turn on the device and press for 5 seconds the com button on the left side of the device.
You will enter the 3 colours loader.
Connect the device to the PC.
Step 2 Install the original Rom
Step 3 Do a Rom update use step 2 of pdamobiz Rom, select update rom file and wait.
Step 4 Do a hardspl G3 or G4 see your device to see witch one is it.
Step 5 install a new Rom with the RUU update utility G3 or G4.
Then you just have to wait the device to reboot and you can use it.
Note: Use the 2.19 radio Rom its the most stable, you can install it after installing the final Rom ok.
Any questions feel free ok bye.
i am sorry but i thought the three colour screen meens bootloader my problem now that i cant change this rom as it dont recognize the memory and also there is prblems with bluetooth.
thanx deltav but ineed more help
Listen up that procedure i explained would put the PDA working 100%, if you have the problems you say you do, its because you installed a rom inappropriate for you device. The memory and bluetooth problems come from bad radio rom and from roms that are not suitable for the device, you mad bad installations, that is the real origin for your problems, if you want to stay with your device with problems fine, in my opinion the best is to put the original rom in and after that, do the rest of procedure if you don´t want to this its up to its your device not mine.
i tried what you said deltav but the problem is there is no 3 color screen and i tried almost all tools of ubgrading and downgrading but i cant remove this rom from my prophet my prophet is G3.
thanks for help but more please
Hello,
Same problem here, no 3-color screen appears when I start or reset and press the comm button on the side.
help for me and seichi please
OK guys after beeing in bootloader mode do a g3 or g4 update with a new rom don´t forget to connect the usb cable correctly, see if it works, if it does not tell me what are your problems, bye.
drdisho said:
i tried what you said deltav but the problem is there is no 3 color screen and i tried almost all tools of ubgrading and downgrading but i cant remove this rom from my prophet my prophet is G3.
thanks for help but more please
Click to expand...
Click to collapse
Listen did you charge the device for 4 hours first on the electricity - step 1
Do a hard reset with the stylus on the device - step 2
press the left com button for 5 seconds on the device, before anything appears on screen - step3
If everything goes well the 3 colour screen will appear.
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...
puhleeze? Helehehehellp me?!
noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??
*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?
goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"
Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???
Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Please need some help ( a lot)
beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+
too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark
Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull
dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.
back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...
ok, will send the s200 to the SAT (repair). I don´t have other options.
hello
i have a big problem with my qtek s200 ,
i made a terrible mistake
i made cid unlock and my s200 is a G4 version
i only see that was a g4 version after ai made the mistake. i am a ****ing asshole .
my version is a G4
ipl 2.10.0001
spl 2.10.0001
Now when i turn on the phone it stuck on the start up screen.
I manualy put on bootloader mode , but every time i tried to flash phone with original version from my country, Portugal. I always get error 302 and dont even start's to flash. it stays always on the rainbow screnn
i already tried many things that i saw here posted but nothing.
i always stay on the rainbow screen, i cant even start flashing the phone
I already changed cable and pc and nothing
can anyone help me?
Thanks in advance
what i did was this that is Cid unlock
http://wiki.xda-developers.com/index.php?pagename=Prophet_CID_Unlock
and on this page says that if
just upgrade to a new G4 ROM and you should be fine.
the problem is that when i put the phone in boot loader mode and try to make the update i get the error [264]: connection
and dont starts updating
can someone help me please
WARNING DO NOT PERFORM THIS IF YOU HAVE A G4 PROPHET (IPL/SPL 2.xx.0001)
Click to expand...
Click to collapse
Have you tried this here ?
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
If the above is successful you will need to hard spl \ soft spl your device then you will be able so go here:
http://forum.xda-developers.com/showthread.php?t=405384
yes i already tried this
I always get error 302 and dont even start's to flash. it stays always on the rainbow screen
any more ideas !!!
read this carefully