some help needed - 8125, K-JAM, P4300, MDA Vario ROM Development

IPL version is: 2.21.0001 and the SPL is 2.21.olip
Rom changes log:-
Original I-mate kjam wm5
to
amp1
to
amp2
to
tnt series 19xx
to
tnt series 20273
to amp v3
Problem is :-
1).when my device start it shows htc logo then tnt series logo then amp logo
2).when I updated to ampv3 it says it has been updated but it shows ampv2 only
How to correct it? So that it shows single logo as I have removed htc & TNT series rom?
When I first changed from imate to amp it showed imate blue screen to amp screen & then I flashed it changed imate screen to htc screen (I forgot what I did that time very long ago).
if i am not wrong my problem is related to somelike here in http://forum.xda-developers.com/showthread.php?t=357787&highlight=kjam

matter solved delete this pls.........

Related

Jamin bricked WM6 IPL SPL 1.00

Hi!
Please help ......... SOS
I bricked my friend's Jamin
It booted fine after I put wm6 but now after I rebooted it,it shows the splash screen with imate logo : ipl : 1.00 , spl : 1.00.0000 , gsm: 01.14.20 , os : 10.1.0.811
any ideas ? pleasee help.......
same thing happened to me when it was softreset with a charger connected. Try removing the battery and/or hardreseting it. should do the trick
just try to hardreset..and then flash it with new ROM

S200 dont boot

Hi everyone,
My qtek s200 dont boot, i just try hardreset, update rom in bootloader but nothing result..
Qtek stays in operator logo
IPL 2.10.0001
SPL 2.10.0001
GSM 02.69.21
OS 4.0.0.0
This happens because i was trying update rom to os 4.0.0.4 and there was a error during de instalation.
Then i try connecting again with activesync 4.5 but there was no conection.
now the qtek dont boot to operating system
Help me please.....
downgrade to wm5,upgrade to wm6,everything should work fine.
wich file?
how can i downgrade to wm5 without activesync?
by bootloader?
Wich file and where i find?
Thanks for your help!!
finally i ugprade to prophet 2.20.7.34 and my s200 is alive again...
Thanks....
How? Same problem here
same problem
i have tried again again end again, and now it's ok
note :
at the end of step 1, when s200 said "tap on screen" -> i have taped
after i have start step 2 as indicated in the tutorial
Good afternoon,
first you must conect pu s200 in bootloader mode (press camera button and make reset with your sylus pen- screen must appear three colors) then plug usb cable, then run the upgrade/downgrade rom
In the end the qtek reboot, install de apps and you must make software reset
Bye
Ratzumen
I have the same problem here. I had the wm6 rom on my qtek s200, but my headset worked not fine with it. So i tried to downgrade to the aku 3 rom for my s200. It seems ok. But when i turned the pda on, id didn't go further that the qtek boot screen. I also could not get to the bootloader screen to update another rom. What can i do?

Help help help

I have a Imate Jamin, Well i never upgraded it so i tried to upgrade to Gullum WM6 touch, I tried to upgrade through this method http://forum.xda-developers.com/showthread.php?t=323013
But i had battery error battery was below 50%, so i upgraded it through Shell tool, i didn't knew its camera button is not working, after flashing complete i couldn't hard reset device so i have to flash to through RUU again, After this IPL and SPL both were 1.XX, OS 2.20.XX. but after it was complete it is stuck on imate splash screen, Then i flashed it with official RUU after which my Ipl, SPL and Rom where back to 1.XX but no results, and then someone here suggested to Flash with PROPHET NVID RUU i also did that now my splash screen is Qtek Ipl 1.00 Spl 2.20.00 Gsm 02.47.21, OS 2.20.7.34 but still it is stuck on slash screen, in all case USb is been detected and i m able to load bootloader through Holding Power off and Communition Mana Buttons. Please help me and reply what should i do now. I think my Phone is Bricked and dead.
Thank you,
Arvin.

[ Need HeLp ] Tytn Won't Boot To OS

I had a tytn II and i flash it witH SPL 3.29 Hard2 using Sifu's 4.0 ROM and radio 1.70.19.09.. It work fine at the begining.. But after i used for a while the system get freeze and tytn restart the device by it self.. The problem is after it get restart it won't boot to OS and it get stuck in first screen which it has text " Smart Mobility" and give info about Radio version and also ROM version.. And it stood still in that screen forever.. Somebody has experience this problem and has a solution.. For the inFo i experience the same probLem as i install another ROM ( AbusaLza ULtimate X2 V.11 ) So I tHink it doesn't had to do witH the ROM.. PLease HeLp me.. Thx beFore..
Kaiser Stuck at Bootloader (aka Tri Color or Red, Green, Blue Screen)? Solutions Here
Use the search & post in the appropriate thread.
Thread closed.

problem IMATE JASJAR

How can I fix this problem, the phone does not want to enter into arrangements Booth, the problem is a program StorageManager, then it does not want to load win mobile, hard reset and give accordingly pressed 0, the phone off and nothing there, it even laptop recognized, please advice on what to do in this case, how to put it in standby Booth, so I can reinstall it.
Rom v V5.2.20931 WWE
Radio 1.14.10
Rom data-11/13/08
Protocol v-42.49.Р8
R 1.14
G 42.42.P8
0 D.07.70 RAN
problem is solved, I found the right combination of buttons, then came into phone mode flash, now works perfectly
please help!!! O2 XDA Exec - CANT OPEN
lm still in the official o2 rom wm5, but last week, l hv try to install a file "Xda_Exec_Upgrade_v1.30.162" through my computer (window 7), when i installing the file , l saw my xda exec's sceen is freeze!!!!! so l just unplug the usb cable through my computer, and soft reset my xda exec, but a worse thing happen. when it it start loading is freeze at the o2 screen with 3 line word at right down corner - ( R 1.09.00 ) , ( G 42.42.P8 ) , ( D 1.30.107 WWE ). And so strange, when l charge my exec there is no light showing, when l remove the battery the light is showing red. l hv put my battery to my friend exec it work!!!
so please help!!!!
1. screen keep freeze at o2 screen???????????
2. when remove battery, and then put it back and charge, the o2 screen come out immediately. without touch any button????? and no light showing.
3. only showing red light when remove the battery????
sorry for the poor english
please help.............
@ jeffeu : put your universal (exec) in bootloader then try to flashing (install) it again.
and do not forget to read xda-wiki -- universal (our device).
Try to activate bootloader and from there to flash, I have a problem with the Win Seven and flash only XP

Categories

Resources