Hi everyone,
My qtek s200 dont boot, i just try hardreset, update rom in bootloader but nothing result..
Qtek stays in operator logo
IPL 2.10.0001
SPL 2.10.0001
GSM 02.69.21
OS 4.0.0.0
This happens because i was trying update rom to os 4.0.0.4 and there was a error during de instalation.
Then i try connecting again with activesync 4.5 but there was no conection.
now the qtek dont boot to operating system
Help me please.....
downgrade to wm5,upgrade to wm6,everything should work fine.
wich file?
how can i downgrade to wm5 without activesync?
by bootloader?
Wich file and where i find?
Thanks for your help!!
finally i ugprade to prophet 2.20.7.34 and my s200 is alive again...
Thanks....
How? Same problem here
same problem
i have tried again again end again, and now it's ok
note :
at the end of step 1, when s200 said "tap on screen" -> i have taped
after i have start step 2 as indicated in the tutorial
Good afternoon,
first you must conect pu s200 in bootloader mode (press camera button and make reset with your sylus pen- screen must appear three colors) then plug usb cable, then run the upgrade/downgrade rom
In the end the qtek reboot, install de apps and you must make software reset
Bye
Ratzumen
I have the same problem here. I had the wm6 rom on my qtek s200, but my headset worked not fine with it. So i tried to downgrade to the aku 3 rom for my s200. It seems ok. But when i turned the pda on, id didn't go further that the qtek boot screen. I also could not get to the bootloader screen to update another rom. What can i do?
Related
I think I have always followed the steps right, but still no succes in booting into WM6. After the hardreset it always stops on the splash screen showing the versions.
I have tried all the versions found here at xda-developers.
It is strange but when I try the ASERG 3.3.13 ROM everything is OK. I am able to boot correctly.
What could be wrong? Is it something with the SPL?
Is there a possibility to debug the boot process?
I have following versions:
IPL 2.09
SPL 2.20.0000
GSM 2.47.21
The device is CID unlocked.
Thanks for every advice.
PiGeonCZ,
Try this:
When doing flashes, usb connect using Active Sync v.4.5, connect as "guest" to sync. Windows XP only. Reboot computer once before starting.
First, very important, flash to the last official wm5 vendor rom of choice. The last I-mate, HTC/QTEK rom is fine. If you're CID unlocked & SIM unlocked, you can use any rom.
For upgrade step 1, download & use this temp rom (PDAviet Temp) to get to first:
http://forum.xda-developers.com/showthread.php?t=308266
Remember, use no other NVID rom out there for this step 1.
Upgrade Step 2: Use this rom for wm6 upgrade: Trueneytral 1.4 with MS Bluetooth stack
http://forum.xda-developers.com/showthread.php?t=302067
If this doesn't work, please let me know.
Hi DevilDuck, thanks for the reply, but no luck again.
This time with device of another my friend, also CID ulnlocked and with the same versions of IPL and SPL.
I am using WinXPSP2 ActiveSync 4.5.0
I did it in following order.
1. update RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe - succesfull
2. tab to see the align screen
3. update Prophet_PDAViet_Step1 - succesfull
4. tab to see the align screen
5. write Prophet_WM6_17913_TrueNeytral_1_4MS - succesfull
6. hardreset
7. stuck on the second splash screen again
So I have tried to write the AKU3.3.13.ASERG-us on this device too and yes it booted succesfully.
I think I have tried all possible combinations and ROMS already, but no luck with WM6.
Any idea?
thanks
Same issue
I have the same issue. I tried all available WM6 ROMs. No success. Please help!
is there a tutorial on how to upgrade to WM6?
guide here: http://forum.xda-developers.com/showthread.php?t=310452
on the second splash screen WAIT 1-2 maybe 3 minutes....
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
^^ ...
hahaha....
now .... charging your phone ... and then turn on your PDA , at the bootloader screen (red,blue,green ... ) , connect you phone with PC .... you will see the USB at the bottom of the screen ... then .... install with the original ROM ...
here is the ROM
http://tom-love.net/Rom/Prophet/WM6.0/Prophet_PV_Temp.zip
i allready did that, and the error 300 keeps coming
what else can i do
ac ... ^^
your phone is G3 .... not G4 ... ^^
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000 is G3
try G3 ....
did you read it before !!!
http://forum.xda-developers.com/showthread.php?t=321839
I have a Imate Jamin, Well i never upgraded it so i tried to upgrade to Gullum WM6 touch, I tried to upgrade through this method http://forum.xda-developers.com/showthread.php?t=323013
But i had battery error battery was below 50%, so i upgraded it through Shell tool, i didn't knew its camera button is not working, after flashing complete i couldn't hard reset device so i have to flash to through RUU again, After this IPL and SPL both were 1.XX, OS 2.20.XX. but after it was complete it is stuck on imate splash screen, Then i flashed it with official RUU after which my Ipl, SPL and Rom where back to 1.XX but no results, and then someone here suggested to Flash with PROPHET NVID RUU i also did that now my splash screen is Qtek Ipl 1.00 Spl 2.20.00 Gsm 02.47.21, OS 2.20.7.34 but still it is stuck on slash screen, in all case USb is been detected and i m able to load bootloader through Holding Power off and Communition Mana Buttons. Please help me and reply what should i do now. I think my Phone is Bricked and dead.
Thank you,
Arvin.
hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all
jamin G3 with SPL 2.13.0001
Hi:
Sorry my english isn't good. I'm spanish.
I read some forum but i don't read the same problem I've.
I've a imate jamin. Last sunday I installed a new rom made by Franlov (WM6.1 Clear). First i make a hardspl and installed the new rom. Well.
After i need install the original rom, but the problem now is:
Jamin KO.
Three color display and the red numbers:
IPL 2.13
SPL 2.13.0001
If I execute a romupdateutility G3, i've a error 300, invalid tool.
If I execute a romudateutility G4, i don't have error but i've the same display (three colors, etc)
I can't make a hardspl because the jamin doesn't run and msdos display says "any device connect".
CAn you help me?
I read it's possible downgrade ipl and spl making a force spl but the program i don't know if exist for jamin or s200.
THANKS
my email: [email protected]
THANKS THANKS THANKS THANKS
melmel1989 said:
hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all
Click to expand...
Click to collapse
I have the same problem! I cannot active sync as it does not connect to the device. So I cannot flash.
IPL 2.13
SPL 2.13.0000
We tried but can not find solution!
I am tired of asking for help, and nothing!
Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5
After that just follow this awsum guide by dioxda2 http://forum.xda-developers.com/showthread.php?t=353547
aia_6584 said:
Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5
Click to expand...
Click to collapse
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....
TJSM said:
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....
Click to expand...
Click to collapse
1. go to my guide, download PVtemp first ~~~~
2, force the prophet to bootloader mode, (how to? see my thread)
3. plug back to USB ( rear PC USB port please...)
4. if you see the "USB" on the left bottom Prophet screen, YOU ARE DONE!!!!
5. Flash PVtemp NOW .... delay is bad~~~~
help me about this
hi,i have a IMATE JAMIN.my phone Does'nt boot after install wm6 & other program.when it turn on display
ipl2.13.0001
spl2.13.0001
gsm02.20.21
os10.2.0.8
after display a black screen & does nothing.
and USB Does'nt recognize my device.
can you help me?
have you tried to Hard Reset the unit after flashing to WM6.1?
You can try it by pressing CAMERA + COMM Button + Reset Button (for 3 seconds)
Hi all
I have a problem with my PDA (Qtek S200)
IPL 2.10.0001
SPL 2.G4.4PDA
GSM 02.69.21
OS 7.0.0.7
ROM Prophet My Diamond Edition 2
And it is this:
Made a backup of my contacts over SPBackup, did the flash ROM of everything he turned to run normally, I made the restores the contacts and SMS, ... and when it does reebot it is only by the initial image that presents the data above:
IPL, SPL, ...
We have tried to make the soft-reset (pen of the button and the small button on the camera and nothing)
My question: Does anyone know how solve this?
Best Regards and thanks
Bye
Edit/Delete Message
Please anybody help me
it´s very urgent.
bye
Done. thanks all for nothing...
you should hard reset your phone