mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
^^ ...
hahaha....
now .... charging your phone ... and then turn on your PDA , at the bootloader screen (red,blue,green ... ) , connect you phone with PC .... you will see the USB at the bottom of the screen ... then .... install with the original ROM ...
here is the ROM
http://tom-love.net/Rom/Prophet/WM6.0/Prophet_PV_Temp.zip
i allready did that, and the error 300 keeps coming
what else can i do
ac ... ^^
your phone is G3 .... not G4 ... ^^
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000 is G3
try G3 ....
did you read it before !!!
http://forum.xda-developers.com/showthread.php?t=321839
Related
Hi,
I try to change ROM from PDAMobiz Prophet WM6 V1.00 to Fantastic Mobiz XBow v1.1i. I made exactly what I was suppose to do. But after few minute i've got the error 300 "INVALID UPDATE TOOL". So I reset my S200, then it's stay on the blue page QTEK until I reset it. I try to upgrade again, but when i'm in the Bootloader mode, i connect the PDA, the letter USB appear on the PDA screen, but i've got the message "No device Connected, Would you like to try copying again", even if i still try few minutes later, it's stil say no device connected.
I don't know what can i do anymore.
Please need Help
Thanks for your help
Benjamin
What S200 you have? G3 or G4? What IPL/SPL Version?
Have you tested to use Step 2? Step 2 use a other Firmware Writer ...
G3
IPL: 2.10.0001
SPL: 2.20.0001
i don't know any other Firmware Writer. Can you tell me one please and where i can find it
thanks
ahm ... IPL/SPL with 0001 is a G4 ... have you write the G3 Firmware? if yes ... you have brick your phone!
by Brick , you mean it's definitly broken, i can do anything?
i was quit sure i used G3 version.
Do you have your dockingstation? Load your Batterie! Then try to enter the bootloader Mode! If you have black screen again ... send it back to you mobile provider and hope they exchange it.
no i don't have any dockstation.
so someone have more proposition please???
can you bring your device into bootloader screen?
from a first view it doesn't seem you bricked it (usually ipl and spl differ then (one is 0000 and one is 0001).
And as you still get an USB Icon i assume it is not broken (but i can't say that for sure).
Just try entering bootloader mode an then flash again (with a g4 firmware!) - see wiki for how to enter BL mode
Hi everyone,
My qtek s200 dont boot, i just try hardreset, update rom in bootloader but nothing result..
Qtek stays in operator logo
IPL 2.10.0001
SPL 2.10.0001
GSM 02.69.21
OS 4.0.0.0
This happens because i was trying update rom to os 4.0.0.4 and there was a error during de instalation.
Then i try connecting again with activesync 4.5 but there was no conection.
now the qtek dont boot to operating system
Help me please.....
downgrade to wm5,upgrade to wm6,everything should work fine.
wich file?
how can i downgrade to wm5 without activesync?
by bootloader?
Wich file and where i find?
Thanks for your help!!
finally i ugprade to prophet 2.20.7.34 and my s200 is alive again...
Thanks....
How? Same problem here
same problem
i have tried again again end again, and now it's ok
note :
at the end of step 1, when s200 said "tap on screen" -> i have taped
after i have start step 2 as indicated in the tutorial
Good afternoon,
first you must conect pu s200 in bootloader mode (press camera button and make reset with your sylus pen- screen must appear three colors) then plug usb cable, then run the upgrade/downgrade rom
In the end the qtek reboot, install de apps and you must make software reset
Bye
Ratzumen
I have the same problem here. I had the wm6 rom on my qtek s200, but my headset worked not fine with it. So i tried to downgrade to the aku 3 rom for my s200. It seems ok. But when i turned the pda on, id didn't go further that the qtek boot screen. I also could not get to the bootloader screen to update another rom. What can i do?
I have a Imate Jamin, Well i never upgraded it so i tried to upgrade to Gullum WM6 touch, I tried to upgrade through this method http://forum.xda-developers.com/showthread.php?t=323013
But i had battery error battery was below 50%, so i upgraded it through Shell tool, i didn't knew its camera button is not working, after flashing complete i couldn't hard reset device so i have to flash to through RUU again, After this IPL and SPL both were 1.XX, OS 2.20.XX. but after it was complete it is stuck on imate splash screen, Then i flashed it with official RUU after which my Ipl, SPL and Rom where back to 1.XX but no results, and then someone here suggested to Flash with PROPHET NVID RUU i also did that now my splash screen is Qtek Ipl 1.00 Spl 2.20.00 Gsm 02.47.21, OS 2.20.7.34 but still it is stuck on slash screen, in all case USb is been detected and i m able to load bootloader through Holding Power off and Communition Mana Buttons. Please help me and reply what should i do now. I think my Phone is Bricked and dead.
Thank you,
Arvin.
I have problem with my 818pro. I upgraded to WM6.1 few months ago successfully with Prophet ROM 19974 M2D. Few days ago suddenly I cant hear anything from phone, but worked well with headset. I read some posts here and try to reinstall the same software which I used few months ago to upgrade from WM5 to WM6.1(with HardSPL G4). The Installation was successful, but when it was restarted, I can only see 3 color screen and USB is written on screen also can see (IPL 2.15.0001 and SPL 2.15.0001). I tried same software few times, but the result is same. The good thing is, I am still able to connect to my PC with USB.
Now I am not able to start my PDA. Every time I restart, It will show same 3 colored screen. and If i connect to USB, it will show on screen USB.
Can Please Please someone help me how can I Install and make it working. Please give me the links as well if possible.
I will be very thankful to you..
Please Help me..
Thanks in advance
Andy
uiell
try flashing back original OS.(wm5)
http://www.htc.com/sea/
[email protected]
Seems HARDSPL not installed.
Information from you.
IPL 2.15.0001 and SPL 2.15.0001
SPL is not HARDSPL already.
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
http://forum.xda-developers.com/showthread.php?t=353547
Try to reflash with PDAVIET NoVendor
But you need to go to Bootloader Mode first ( manually). Read how to do it.
Make sure battery enough.
And flash with the ROM above.
And do the HARDSPL again.
http://forum.xda-developers.com/showthread.php?t=405384
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
Information for you : Installation, even not HARDSPL could be succesfull. But you will always stuck in Bootloader mode, like you have now.
So Reflash it first like I said and HARDSPL again.
Until SPL information like this SPL 2.G4.4PDA. Cos you have G4 Device.
hello
i have a big problem with my qtek s200 ,
i made a terrible mistake
i made cid unlock and my s200 is a G4 version
i only see that was a g4 version after ai made the mistake. i am a ****ing asshole .
my version is a G4
ipl 2.10.0001
spl 2.10.0001
Now when i turn on the phone it stuck on the start up screen.
I manualy put on bootloader mode , but every time i tried to flash phone with original version from my country, Portugal. I always get error 302 and dont even start's to flash. it stays always on the rainbow screnn
i already tried many things that i saw here posted but nothing.
i always stay on the rainbow screen, i cant even start flashing the phone
I already changed cable and pc and nothing
can anyone help me?
Thanks in advance
what i did was this that is Cid unlock
http://wiki.xda-developers.com/index.php?pagename=Prophet_CID_Unlock
and on this page says that if
just upgrade to a new G4 ROM and you should be fine.
the problem is that when i put the phone in boot loader mode and try to make the update i get the error [264]: connection
and dont starts updating
can someone help me please
WARNING DO NOT PERFORM THIS IF YOU HAVE A G4 PROPHET (IPL/SPL 2.xx.0001)
Click to expand...
Click to collapse
Have you tried this here ?
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
If the above is successful you will need to hard spl \ soft spl your device then you will be able so go here:
http://forum.xda-developers.com/showthread.php?t=405384
yes i already tried this
I always get error 302 and dont even start's to flash. it stays always on the rainbow screen
any more ideas !!!
read this carefully