Hi,
I try to change ROM from PDAMobiz Prophet WM6 V1.00 to Fantastic Mobiz XBow v1.1i. I made exactly what I was suppose to do. But after few minute i've got the error 300 "INVALID UPDATE TOOL". So I reset my S200, then it's stay on the blue page QTEK until I reset it. I try to upgrade again, but when i'm in the Bootloader mode, i connect the PDA, the letter USB appear on the PDA screen, but i've got the message "No device Connected, Would you like to try copying again", even if i still try few minutes later, it's stil say no device connected.
I don't know what can i do anymore.
Please need Help
Thanks for your help
Benjamin
What S200 you have? G3 or G4? What IPL/SPL Version?
Have you tested to use Step 2? Step 2 use a other Firmware Writer ...
G3
IPL: 2.10.0001
SPL: 2.20.0001
i don't know any other Firmware Writer. Can you tell me one please and where i can find it
thanks
ahm ... IPL/SPL with 0001 is a G4 ... have you write the G3 Firmware? if yes ... you have brick your phone!
by Brick , you mean it's definitly broken, i can do anything?
i was quit sure i used G3 version.
Do you have your dockingstation? Load your Batterie! Then try to enter the bootloader Mode! If you have black screen again ... send it back to you mobile provider and hope they exchange it.
no i don't have any dockstation.
so someone have more proposition please???
can you bring your device into bootloader screen?
from a first view it doesn't seem you bricked it (usually ipl and spl differ then (one is 0000 and one is 0001).
And as you still get an USB Icon i assume it is not broken (but i can't say that for sure).
Just try entering bootloader mode an then flash again (with a g4 firmware!) - see wiki for how to enter BL mode
Related
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
jasonrabbit said:
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
Click to expand...
Click to collapse
i have the same problem too, i used g4 rom and now its stuck at bootloader rainbow screen.
my IPL is 1.00
SPL is 2.20.0001
jester gold card
after lots of looking and reading of threads i need to wait for Jester Gold Card
come on jester work your magic my M600 is now a paper weight.
jasonrabbit said:
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
Click to expand...
Click to collapse
Hi,
Its very common to do mistake of flashing G3 device with G4 rom, and
no of people doing this mistake increasing every day.
Its very sad to have a bricked device, rather it wud hav been better
to search the forum thourouly before making attempt to flash.
Yes the only hope is Gold Card Project success,
We all r waiting for that day!
ic. Gold Card Project
anyway i did a stupid mistake that lead my prophet into a paper weight.
i click on the G4 rom thinking thats step 2...
now i cant down grade back to old wm5
If You & press camera button + reset
You'll get in the bootloader screen
after that try a ROM wich is your phone's
( I disconnected while updateing tot jesters AKU 3.3 )
Have a functional phone now
CooT said:
If You & press camera button + reset
You'll get in the bootloader screen
after that try a ROM wich is your phone's
( I disconnected while updateing tot jesters AKU 3.3 )
Have a functional phone now
Click to expand...
Click to collapse
no, u cant flash anything now as g4 rom is inside a g3 device
and the moment u try to "downgrade" it will prompt for a NEWER FILE to be used
my m600 stucked at very starting screen help me plz
hi guys
i got a orange spv m600 i tried to unlock it from the stuff which i got online but instead i messed up the phone
its stucked at the vry first screen showing a orang logo
and
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
could any one help me out plz plz plz i am a new person and i dont know any thinig about this roms or any software u can email me my emial id is
[email protected]
subject m600(plz dont forget to mentioned in the subject field) bcoz i get loads of junk mail that y i delete them
thanks
Same Problem
I have a fried M600 that is also stuck in the "Orange" Screen when turned on...
How can I get past this?
I have tried re-installing the original ROM but it still refuses to boot.
What Installer do I need to download?
Which ROM would do the trick?
How do you install CAB files without Activesync?
Can anyone help me on this as I'm lost without my M600.....
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
^^ ...
hahaha....
now .... charging your phone ... and then turn on your PDA , at the bootloader screen (red,blue,green ... ) , connect you phone with PC .... you will see the USB at the bottom of the screen ... then .... install with the original ROM ...
here is the ROM
http://tom-love.net/Rom/Prophet/WM6.0/Prophet_PV_Temp.zip
i allready did that, and the error 300 keeps coming
what else can i do
ac ... ^^
your phone is G3 .... not G4 ... ^^
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000 is G3
try G3 ....
did you read it before !!!
http://forum.xda-developers.com/showthread.php?t=321839
Hi ,
I've try to upgrade my O2 xda, I've read IPL and SPL .0001, then i think is a G4, I've connect to PC, launch hardspl.bat from update_package and then the smartphone restart, but the screen remain white, activesync 4.5 not recognized it.
Please help me!
I've also try to use the alternate hardspl file of this thread: http://forum.xda-developers.com/showthread.php?t=353547&highlight=white+screen+hardspl but nothing.
white screen after launch jumpspl and must soft reset to continue.
I've a Dutch O2 XDA with SPL 2.15.0001.
Is possible to have lock CID or similar?
Someone can help me?
Can I make some hardreset or similar?
Thanks in advance!
G4 devices cannot be CID unlocked although the HardSPL circumvents the CID procedure.
The white screen is what happens after you hard SPL: http://forum.xda-developers.com/showthread.php?t=353547
You can hard reset although you will loose all your data. To hard reset, hold the camera button, the comm manager button and soft reset. Then follow the message on screen.
Thanks!
If I've a CID locked G4 I can't upgrade?
I've read the guide but I've not found a reply to my question. I've also try the alternate hardspl utility.
You can upgrade a G4 without CID unlocking (I have a g4 and WM6.1) You should be able to upgrade after SIM unlocking your device and HardSPLing your device. Try flashing a ROM when the device is connected but with the white screen and see if anything works on the PC.
When smartphone is white screen activesync not recognize any.
How I can verify if there is CID lock?
If it is a G4, there will be a CID lock unless it's an unbranded (HTC) device.
The CID lock will not affect the flashing procedure.
Ignore the fact that activesync doesn't recognise it and see if an RUU will recognise the device.
I've try now with cofferom, when screen white the RUU not phone, connection error (264).
When your device starts up, what is the IPL and SPL displayed?
ipl and spl 2.15.0001
I explain my step:
First launch the file "Update_Package\Update_Package\HardSPL\HardSPL G4\hardspl.bat" this file launch in smartphone the file jump.exe then I click on Yes on smartphone and the white screen appears, after this on PC appears a RUU, I close this and lauch the file: CoffieITA\Flash tools\ROMUpdateUtility_NV_G4.exe but this not recognize the smartphone.
I wrong any? the first RUU after hardspl.bat what is this?
HardSPL has not succeded. Try softSPL rather than hardSPL and see if the RUU will connect.
I've undestand where I wrong, now I've completed the operation and I've SPL: 2.G4.4PDA is ok?
Yes. Now try and flash a ROM.
WORKING!
Now it is in italian!
Thanks a lot! Thanks!
No problem!
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...
puhleeze? Helehehehellp me?!
noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??
*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?
goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"
Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???
Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...
hello
i have a big problem with my qtek s200 ,
i made a terrible mistake
i made cid unlock and my s200 is a G4 version
i only see that was a g4 version after ai made the mistake. i am a ****ing asshole .
my version is a G4
ipl 2.10.0001
spl 2.10.0001
Now when i turn on the phone it stuck on the start up screen.
I manualy put on bootloader mode , but every time i tried to flash phone with original version from my country, Portugal. I always get error 302 and dont even start's to flash. it stays always on the rainbow screnn
i already tried many things that i saw here posted but nothing.
i always stay on the rainbow screen, i cant even start flashing the phone
I already changed cable and pc and nothing
can anyone help me?
Thanks in advance
what i did was this that is Cid unlock
http://wiki.xda-developers.com/index.php?pagename=Prophet_CID_Unlock
and on this page says that if
just upgrade to a new G4 ROM and you should be fine.
the problem is that when i put the phone in boot loader mode and try to make the update i get the error [264]: connection
and dont starts updating
can someone help me please
WARNING DO NOT PERFORM THIS IF YOU HAVE A G4 PROPHET (IPL/SPL 2.xx.0001)
Click to expand...
Click to collapse
Have you tried this here ?
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
If the above is successful you will need to hard spl \ soft spl your device then you will be able so go here:
http://forum.xda-developers.com/showthread.php?t=405384
yes i already tried this
I always get error 302 and dont even start's to flash. it stays always on the rainbow screen
any more ideas !!!
read this carefully