I have a Imate Jamin, Well i never upgraded it so i tried to upgrade to Gullum WM6 touch, I tried to upgrade through this method http://forum.xda-developers.com/showthread.php?t=323013
But i had battery error battery was below 50%, so i upgraded it through Shell tool, i didn't knew its camera button is not working, after flashing complete i couldn't hard reset device so i have to flash to through RUU again, After this IPL and SPL both were 1.XX, OS 2.20.XX. but after it was complete it is stuck on imate splash screen, Then i flashed it with official RUU after which my Ipl, SPL and Rom where back to 1.XX but no results, and then someone here suggested to Flash with PROPHET NVID RUU i also did that now my splash screen is Qtek Ipl 1.00 Spl 2.20.00 Gsm 02.47.21, OS 2.20.7.34 but still it is stuck on slash screen, in all case USb is been detected and i m able to load bootloader through Holding Power off and Communition Mana Buttons. Please help me and reply what should i do now. I think my Phone is Bricked and dead.
Thank you,
Arvin.
Related
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
jasonrabbit said:
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
Click to expand...
Click to collapse
i have the same problem too, i used g4 rom and now its stuck at bootloader rainbow screen.
my IPL is 1.00
SPL is 2.20.0001
jester gold card
after lots of looking and reading of threads i need to wait for Jester Gold Card
come on jester work your magic my M600 is now a paper weight.
jasonrabbit said:
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
Click to expand...
Click to collapse
Hi,
Its very common to do mistake of flashing G3 device with G4 rom, and
no of people doing this mistake increasing every day.
Its very sad to have a bricked device, rather it wud hav been better
to search the forum thourouly before making attempt to flash.
Yes the only hope is Gold Card Project success,
We all r waiting for that day!
ic. Gold Card Project
anyway i did a stupid mistake that lead my prophet into a paper weight.
i click on the G4 rom thinking thats step 2...
now i cant down grade back to old wm5
If You & press camera button + reset
You'll get in the bootloader screen
after that try a ROM wich is your phone's
( I disconnected while updateing tot jesters AKU 3.3 )
Have a functional phone now
CooT said:
If You & press camera button + reset
You'll get in the bootloader screen
after that try a ROM wich is your phone's
( I disconnected while updateing tot jesters AKU 3.3 )
Have a functional phone now
Click to expand...
Click to collapse
no, u cant flash anything now as g4 rom is inside a g3 device
and the moment u try to "downgrade" it will prompt for a NEWER FILE to be used
my m600 stucked at very starting screen help me plz
hi guys
i got a orange spv m600 i tried to unlock it from the stuff which i got online but instead i messed up the phone
its stucked at the vry first screen showing a orang logo
and
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
could any one help me out plz plz plz i am a new person and i dont know any thinig about this roms or any software u can email me my emial id is
[email protected]
subject m600(plz dont forget to mentioned in the subject field) bcoz i get loads of junk mail that y i delete them
thanks
Same Problem
I have a fried M600 that is also stuck in the "Orange" Screen when turned on...
How can I get past this?
I have tried re-installing the original ROM but it still refuses to boot.
What Installer do I need to download?
Which ROM would do the trick?
How do you install CAB files without Activesync?
Can anyone help me on this as I'm lost without my M600.....
Hi everyone,
My qtek s200 dont boot, i just try hardreset, update rom in bootloader but nothing result..
Qtek stays in operator logo
IPL 2.10.0001
SPL 2.10.0001
GSM 02.69.21
OS 4.0.0.0
This happens because i was trying update rom to os 4.0.0.4 and there was a error during de instalation.
Then i try connecting again with activesync 4.5 but there was no conection.
now the qtek dont boot to operating system
Help me please.....
downgrade to wm5,upgrade to wm6,everything should work fine.
wich file?
how can i downgrade to wm5 without activesync?
by bootloader?
Wich file and where i find?
Thanks for your help!!
finally i ugprade to prophet 2.20.7.34 and my s200 is alive again...
Thanks....
How? Same problem here
same problem
i have tried again again end again, and now it's ok
note :
at the end of step 1, when s200 said "tap on screen" -> i have taped
after i have start step 2 as indicated in the tutorial
Good afternoon,
first you must conect pu s200 in bootloader mode (press camera button and make reset with your sylus pen- screen must appear three colors) then plug usb cable, then run the upgrade/downgrade rom
In the end the qtek reboot, install de apps and you must make software reset
Bye
Ratzumen
I have the same problem here. I had the wm6 rom on my qtek s200, but my headset worked not fine with it. So i tried to downgrade to the aku 3 rom for my s200. It seems ok. But when i turned the pda on, id didn't go further that the qtek boot screen. I also could not get to the bootloader screen to update another rom. What can i do?
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
^^ ...
hahaha....
now .... charging your phone ... and then turn on your PDA , at the bootloader screen (red,blue,green ... ) , connect you phone with PC .... you will see the USB at the bottom of the screen ... then .... install with the original ROM ...
here is the ROM
http://tom-love.net/Rom/Prophet/WM6.0/Prophet_PV_Temp.zip
i allready did that, and the error 300 keeps coming
what else can i do
ac ... ^^
your phone is G3 .... not G4 ... ^^
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000 is G3
try G3 ....
did you read it before !!!
http://forum.xda-developers.com/showthread.php?t=321839
I have problem with my 818pro. I upgraded to WM6.1 few months ago successfully with Prophet ROM 19974 M2D. Few days ago suddenly I cant hear anything from phone, but worked well with headset. I read some posts here and try to reinstall the same software which I used few months ago to upgrade from WM5 to WM6.1(with HardSPL G4). The Installation was successful, but when it was restarted, I can only see 3 color screen and USB is written on screen also can see (IPL 2.15.0001 and SPL 2.15.0001). I tried same software few times, but the result is same. The good thing is, I am still able to connect to my PC with USB.
Now I am not able to start my PDA. Every time I restart, It will show same 3 colored screen. and If i connect to USB, it will show on screen USB.
Can Please Please someone help me how can I Install and make it working. Please give me the links as well if possible.
I will be very thankful to you..
Please Help me..
Thanks in advance
Andy
uiell
try flashing back original OS.(wm5)
http://www.htc.com/sea/
[email protected]
Seems HARDSPL not installed.
Information from you.
IPL 2.15.0001 and SPL 2.15.0001
SPL is not HARDSPL already.
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
http://forum.xda-developers.com/showthread.php?t=353547
Try to reflash with PDAVIET NoVendor
But you need to go to Bootloader Mode first ( manually). Read how to do it.
Make sure battery enough.
And flash with the ROM above.
And do the HARDSPL again.
http://forum.xda-developers.com/showthread.php?t=405384
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
Information for you : Installation, even not HARDSPL could be succesfull. But you will always stuck in Bootloader mode, like you have now.
So Reflash it first like I said and HARDSPL again.
Until SPL information like this SPL 2.G4.4PDA. Cos you have G4 Device.
Sory.. this is my new post on this forum! And i'm a new comer on PDA.
Please help!! I've tried to upgrade my dopod c800 to WM6 through activesync.. but (i did'nt know the term "brick" before) my dopod is sudenly dead after error on my PC.
I could go into hard reset, but no to bootloader (CAMERA+stylus). When i push other button after hard reset.. it'll go into green screen with ipl and spl only. If i then push soft reset with stylus, it's turn off.
my ipl/spl is 1.xxxxxx
Please help!!
nurdiman said:
Sory.. this is my new post on this forum! And i'm a new comer on PDA.
Please help!! I've tried to upgrade my dopod c800 to WM6 through activesync.. but (i did'nt know the term "brick" before) my dopod is sudenly dead after error on my PC.
I could go into hard reset, but no to bootloader (CAMERA+stylus). When i push other button after hard reset.. it'll go into green screen with ipl and spl only. If i then push soft reset with stylus, it's turn off.
my ipl/spl is 1.xxxxxx
Please help!!
Click to expand...
Click to collapse
You probably broke your SPL/IPL. The warning says to not flash a third party ROM on your phone if your SPL is lower than 4.xx
If you can get back to the bootloader, you can use the goldcard method to revive your phone. I have not done the goldcard method myself, so I cannot answer any questions on it.