Sory.. this is my new post on this forum! And i'm a new comer on PDA.
Please help!! I've tried to upgrade my dopod c800 to WM6 through activesync.. but (i did'nt know the term "brick" before) my dopod is sudenly dead after error on my PC.
I could go into hard reset, but no to bootloader (CAMERA+stylus). When i push other button after hard reset.. it'll go into green screen with ipl and spl only. If i then push soft reset with stylus, it's turn off.
my ipl/spl is 1.xxxxxx
Please help!!
nurdiman said:
Sory.. this is my new post on this forum! And i'm a new comer on PDA.
Please help!! I've tried to upgrade my dopod c800 to WM6 through activesync.. but (i did'nt know the term "brick" before) my dopod is sudenly dead after error on my PC.
I could go into hard reset, but no to bootloader (CAMERA+stylus). When i push other button after hard reset.. it'll go into green screen with ipl and spl only. If i then push soft reset with stylus, it's turn off.
my ipl/spl is 1.xxxxxx
Please help!!
Click to expand...
Click to collapse
You probably broke your SPL/IPL. The warning says to not flash a third party ROM on your phone if your SPL is lower than 4.xx
If you can get back to the bootloader, you can use the goldcard method to revive your phone. I have not done the goldcard method myself, so I cannot answer any questions on it.
Related
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
jasonrabbit said:
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
Click to expand...
Click to collapse
i have the same problem too, i used g4 rom and now its stuck at bootloader rainbow screen.
my IPL is 1.00
SPL is 2.20.0001
jester gold card
after lots of looking and reading of threads i need to wait for Jester Gold Card
come on jester work your magic my M600 is now a paper weight.
jasonrabbit said:
hi can you please help i flashed my M600 with jester 2.20 G4 now my phone is stuck in bootloader.
if i hard reset then press send if comes up format failed
i have reloaded rom 2-3 times but still same fault
bootloader screen shows
IPL 2.09
SPL 2.20.0001
have i flashed my phone with the wrong rom ?
can my M600 be saved
thanks for any help
Click to expand...
Click to collapse
Hi,
Its very common to do mistake of flashing G3 device with G4 rom, and
no of people doing this mistake increasing every day.
Its very sad to have a bricked device, rather it wud hav been better
to search the forum thourouly before making attempt to flash.
Yes the only hope is Gold Card Project success,
We all r waiting for that day!
ic. Gold Card Project
anyway i did a stupid mistake that lead my prophet into a paper weight.
i click on the G4 rom thinking thats step 2...
now i cant down grade back to old wm5
If You & press camera button + reset
You'll get in the bootloader screen
after that try a ROM wich is your phone's
( I disconnected while updateing tot jesters AKU 3.3 )
Have a functional phone now
CooT said:
If You & press camera button + reset
You'll get in the bootloader screen
after that try a ROM wich is your phone's
( I disconnected while updateing tot jesters AKU 3.3 )
Have a functional phone now
Click to expand...
Click to collapse
no, u cant flash anything now as g4 rom is inside a g3 device
and the moment u try to "downgrade" it will prompt for a NEWER FILE to be used
my m600 stucked at very starting screen help me plz
hi guys
i got a orange spv m600 i tried to unlock it from the stuff which i got online but instead i messed up the phone
its stucked at the vry first screen showing a orang logo
and
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
could any one help me out plz plz plz i am a new person and i dont know any thinig about this roms or any software u can email me my emial id is
[email protected]
subject m600(plz dont forget to mentioned in the subject field) bcoz i get loads of junk mail that y i delete them
thanks
Same Problem
I have a fried M600 that is also stuck in the "Orange" Screen when turned on...
How can I get past this?
I have tried re-installing the original ROM but it still refuses to boot.
What Installer do I need to download?
Which ROM would do the trick?
How do you install CAB files without Activesync?
Can anyone help me on this as I'm lost without my M600.....
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
try this
1) hold your communication button and soft reset *keep holding comm-button until see the RGB color bar,
2) plug-in your USB cable, u will see a 'USB' appear at your bottom left,
3) install the flash ROM from your window.
well I tried install WM6 once fail, so I do the above step, and 2nd time successfully upgrade to WM6, you can use back your original ROM download form dopod site.
goodluck
feiyee said:
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
Click to expand...
Click to collapse
It's easy, mail your dopd to me.
I have a Imate Jamin, Well i never upgraded it so i tried to upgrade to Gullum WM6 touch, I tried to upgrade through this method http://forum.xda-developers.com/showthread.php?t=323013
But i had battery error battery was below 50%, so i upgraded it through Shell tool, i didn't knew its camera button is not working, after flashing complete i couldn't hard reset device so i have to flash to through RUU again, After this IPL and SPL both were 1.XX, OS 2.20.XX. but after it was complete it is stuck on imate splash screen, Then i flashed it with official RUU after which my Ipl, SPL and Rom where back to 1.XX but no results, and then someone here suggested to Flash with PROPHET NVID RUU i also did that now my splash screen is Qtek Ipl 1.00 Spl 2.20.00 Gsm 02.47.21, OS 2.20.7.34 but still it is stuck on slash screen, in all case USb is been detected and i m able to load bootloader through Holding Power off and Communition Mana Buttons. Please help me and reply what should i do now. I think my Phone is Bricked and dead.
Thank you,
Arvin.
Hi ,
I've try to upgrade my O2 xda, I've read IPL and SPL .0001, then i think is a G4, I've connect to PC, launch hardspl.bat from update_package and then the smartphone restart, but the screen remain white, activesync 4.5 not recognized it.
Please help me!
I've also try to use the alternate hardspl file of this thread: http://forum.xda-developers.com/showthread.php?t=353547&highlight=white+screen+hardspl but nothing.
white screen after launch jumpspl and must soft reset to continue.
I've a Dutch O2 XDA with SPL 2.15.0001.
Is possible to have lock CID or similar?
Someone can help me?
Can I make some hardreset or similar?
Thanks in advance!
G4 devices cannot be CID unlocked although the HardSPL circumvents the CID procedure.
The white screen is what happens after you hard SPL: http://forum.xda-developers.com/showthread.php?t=353547
You can hard reset although you will loose all your data. To hard reset, hold the camera button, the comm manager button and soft reset. Then follow the message on screen.
Thanks!
If I've a CID locked G4 I can't upgrade?
I've read the guide but I've not found a reply to my question. I've also try the alternate hardspl utility.
You can upgrade a G4 without CID unlocking (I have a g4 and WM6.1) You should be able to upgrade after SIM unlocking your device and HardSPLing your device. Try flashing a ROM when the device is connected but with the white screen and see if anything works on the PC.
When smartphone is white screen activesync not recognize any.
How I can verify if there is CID lock?
If it is a G4, there will be a CID lock unless it's an unbranded (HTC) device.
The CID lock will not affect the flashing procedure.
Ignore the fact that activesync doesn't recognise it and see if an RUU will recognise the device.
I've try now with cofferom, when screen white the RUU not phone, connection error (264).
When your device starts up, what is the IPL and SPL displayed?
ipl and spl 2.15.0001
I explain my step:
First launch the file "Update_Package\Update_Package\HardSPL\HardSPL G4\hardspl.bat" this file launch in smartphone the file jump.exe then I click on Yes on smartphone and the white screen appears, after this on PC appears a RUU, I close this and lauch the file: CoffieITA\Flash tools\ROMUpdateUtility_NV_G4.exe but this not recognize the smartphone.
I wrong any? the first RUU after hardspl.bat what is this?
HardSPL has not succeded. Try softSPL rather than hardSPL and see if the RUU will connect.
I've undestand where I wrong, now I've completed the operation and I've SPL: 2.G4.4PDA is ok?
Yes. Now try and flash a ROM.
WORKING!
Now it is in italian!
Thanks a lot! Thanks!
No problem!
I have problem with my 818pro. I upgraded to WM6.1 few months ago successfully with Prophet ROM 19974 M2D. Few days ago suddenly I cant hear anything from phone, but worked well with headset. I read some posts here and try to reinstall the same software which I used few months ago to upgrade from WM5 to WM6.1(with HardSPL G4). The Installation was successful, but when it was restarted, I can only see 3 color screen and USB is written on screen also can see (IPL 2.15.0001 and SPL 2.15.0001). I tried same software few times, but the result is same. The good thing is, I am still able to connect to my PC with USB.
Now I am not able to start my PDA. Every time I restart, It will show same 3 colored screen. and If i connect to USB, it will show on screen USB.
Can Please Please someone help me how can I Install and make it working. Please give me the links as well if possible.
I will be very thankful to you..
Please Help me..
Thanks in advance
Andy
uiell
try flashing back original OS.(wm5)
http://www.htc.com/sea/
[email protected]
Seems HARDSPL not installed.
Information from you.
IPL 2.15.0001 and SPL 2.15.0001
SPL is not HARDSPL already.
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
http://forum.xda-developers.com/showthread.php?t=353547
Try to reflash with PDAVIET NoVendor
But you need to go to Bootloader Mode first ( manually). Read how to do it.
Make sure battery enough.
And flash with the ROM above.
And do the HARDSPL again.
http://forum.xda-developers.com/showthread.php?t=405384
The SPL Information , if already HARDSPL should be SPL 2.G4.4PDA. Cos you have G4 Device.
Information for you : Installation, even not HARDSPL could be succesfull. But you will always stuck in Bootloader mode, like you have now.
So Reflash it first like I said and HARDSPL again.
Until SPL information like this SPL 2.G4.4PDA. Cos you have G4 Device.