Hi Ive just upgraded to WM6 for VOIP mainly, Im using the NBD rom and theyre doesnt seem to be any audio on the handset (tried headset too), although on the person I call I can hear the audio from the XDA, any solutions or help would be appreciated
AdamG said:
Hi Ive just upgraded to WM6 for VOIP mainly, Im using the NBD rom and theyre doesnt seem to be any audio on the handset (tried headset too), although on the person I call I can hear the audio from the XDA, any solutions or help would be appreciated
Click to expand...
Click to collapse
VOIP calls usually come thru the speaker phone rather than the handset earpiece.. usually the case with some htc phone (due to hardware).. Even if you plugged in the headphones.. make sure your volume is hight (not at the vaibrate mode)... I've had this issue with my Cingular 8125 (Wiz100)..
But I am currently using the mfrazz's R1.7 rom and with the voip configs and it works fine..
If you've tried what I've mentioned to you and you are certain that it's not your phone that's causing it.. than it's the voip relay.. as you might experince the 1 way audio.. which happens once in a while with due to firewall issues and etc..
You see viop handshake usually takes place on port 5060 but the rtp stream can fall from port 6K-65K range.. (usually 60-65K).. but with this if any of the port gets blocked you can experience 1 way audio..
I am telling you this cause I work for a voip company and this usually happens once in a while with misconfigured firewalls.. voip works best on static ip. if you are behind nat than you might need to connect thru a session border controller.
Hope that helps..
I set DMZ up on the router so the public IP was assigned to the device, tried turning the volme up on the headset like you suggested as well, Ive also tried a couple of VOIP applications and I had the same problem with the audio, could it be the ROM? but then if it was outgoing audio is fine but not incomeing :S
Related
I bought the Jabra BT-800 headset for 119 EUR and was hoping to enjoy the headset w/o getting my PPC out of my pocketst.
Well that didnt work out. Pairing was easy, and after switching on the headset (in profile on today screen) I could call with it. The only thing is, I cannot get the call list on the headset to work. It doesnt show any numbers at all, and i wonder how its supposed to work anyway.
That being said, I also don't get to see who's calling me when using the headset.
1) Incoming call.... PPC rings..
2) After a few seconds the headset backlight switches on showing "Jabra BT-800" (standard text). I do not get to see who's calling me on my headset.
3) When listening to the ring tone on headset, after a second or two I get a really annoying sqreaking sound and that stays on till I accept the call or hang up.
So it is not working for me. Besides the headset does not stay on my ear correctly. I have small ears and it is really uncomfortable.
I have Qtek 2020 with Windows Mobile 2003 SE ROM (downloaded from this forum), ROM version 2.06.00WWE, Radio 1.18.00, Protocol 1337.38, ExtROM 2.06.100a
The Jabra BT-800 does not do what they say it's supposed to do.
Anyone else got these problems or solutions? Ciao
R.
me too
Same problem... They say it is also capable of BT voice dialing. I hate the way it takes so long to answer calls.
I am going to find out if the sony ericson ones work.. Then get that. The reception on the BT800 is great though.
Re: me too
dewild1 said:
Same problem... They say it is also capable of BT voice dialing. I hate the way it takes so long to answer calls.
I am going to find out if the sony ericson ones work.. Then get that. The reception on the BT800 is great though.
Click to expand...
Click to collapse
Lucky you to get that far :evil:
After the upgrade to the Diamond 1.2 I have tried to bond my Bluespoon Digital. That was very easy and everything works fine, exept a call not is trasferred to the headset. I have tried both stacks, and I have tried it with the Sony Ericsson HBH 65. It simply doesn't work at all.
Does anybody have suggestions to what to do??
bluetooth headset not bonding
:lol:
Hi , I had smae problem with new I.Tech clip headset.
It's ok now as I downloaded the POcket Bluetotth Tools from this link:
http://bluetooth.i-networx.de/index_e.html
Now it's ok for incoming and outgoing calls...
Cheers..
Fingers
Persnickety Bluetooth
Thanks for the link!
I had a problem with my Jabra BT250 after the WM upgrade. The mic and speaker remained active on the device, and the earpeice on my headset was active, but not the headset mic. The BT Tools did the trick.
Thanks
Jabra BT800 & XDA ii
Hi there,
The Jabra BT800 isnt compatable with the XDA ii (check www.jabra.com)
I owned this headset and had exactly the same problems, i now own the Jabra BT200 and it works perfectly
The BT800 needs a phone with bluetooth handsfree profile to be able to use the advanced features like caller id. Xda II as standard has only bluetooth headset profile.
I'm not sure about the 2003SE rom some of you guys are using, but I've tried it with the Buzz WM2K5 rom (thanks buzz et al) and this DOES give it the bluetooth handsfree profile it needs.
BUT...
It seems Jabra's idea of caller id is to only pass the number across, and not the name. So for those of us that don't have a photographic memory its pretty useless. This isn't restricted to Xda's either. I tried a couple of Nokia phones that are 'compatible' according to www.jabra.com and these do exactly the same. Number shows on the jabra screen but no name, even though the phone is showing both.
I emailed Jabra about it and they acknowledge it is an issue. They also tell me there is an issue with numbers in international format in that they fail to pass the + sign across, so you can't ring out from the call list.
JD
Ya need 2.20 translated to have a working Hands Free profile.. BT800 needs hands free profile.
Caller ID still only displays if the number is a virgin to your system.. I think HBH662 will work with 2.20.
2005 may work with no problems too.
Can u guys recommend me which is the best ROM for VOIP to work properly? Does the front speaker issue still exist in WM 6.1?
I understand using headset is the only option to get the voip working , but was wondering if there's solutions out there already?
spawnbd said:
Can u guys recommend me which is the best ROM for VOIP to work properly? Does the front speaker issue still exist in WM 6.1?
I understand using headset is the only option to get the voip working , but was wondering if there's solutions out there already?
Click to expand...
Click to collapse
What service do you have for VoIP?
eagle 1 said:
What service do you have for VoIP?
Click to expand...
Click to collapse
SIP based service..I use www.pennytel.com
I am already using voip on my kaiser with official WM 6 ROM, but sound comes from the rear speaker
Front speaker issue is device dependent not WM version. AFAIK only a few devices work correctly. These devices had native VoIP at one time too. My latest VoIP cab (located here) can also connect with the GSM610 codec (kudos to dridders for figuring this out) which is much more efficient over a 3G connection. It also eliminates the one-way audio issues.
As an added benefit, the installation will work over a bluetooth handsfree as well. I've actually connected up over 3G then handed the phone functions off to my car handsfree w/o issues. Audio quality doesn't match GSM of course but its usable. For the most part this is a technology demo however. The only time I've found it really useful is when I'm in WiFi coverage but have no phone service.
I use asterisk with some providers such as pennytel ( Australia ) and other european providers. I'd really love to have my Kaiser working properly over WiFi (I didn't try over 3G yet).
I use to have a Hermes that was working properly (Ear Speaker) - though there was a lot of jitter - I now moved to the kaiser and VoIP (SIP) is finally working properly (no jitter) but only through the loudspeaker. I now have to use a headset...
I'd really like to have this finally working. I'm currently stuck to two stage dialing through asterisk (with unlimited plan to a few numbers) to use VoIP from my Cell.
Does anyone have some background info on how the VoIP plugin should be talking to the ear speaker (does it have to go through the "radio rom"? is it seen as a secondary speaker? etc.) and if anyone has ever fixed such an issues with other WM6 handsets?
jinkazama007 said:
I now moved to the kaiser and VoIP (SIP) is finally working properly (no jitter) but only through the loudspeaker. I now have to use a headset...
Click to expand...
Click to collapse
As you are on the same boat, can I ask you which Bluetooth headset are you using? There are quite a few headset recommendations out there, but I wanna know from someone who is using it for voip. Thanks
Sleuth255 said:
Front speaker issue is device dependent not WM version. AFAIK only a few devices work correctly. These devices had native VoIP at one time too. My latest VoIP cab (located here) can also connect with the GSM610 codec (kudos to dridders for figuring this out) which is much more efficient over a 3G connection. It also eliminates the one-way audio issues.
As an added benefit, the installation will work over a bluetooth handsfree as well. I've actually connected up over 3G then handed the phone functions off to my car handsfree w/o issues. Audio quality doesn't match GSM of course but its usable. For the most part this is a technology demo however. The only time I've found it really useful is when I'm in WiFi coverage but have no phone service.
Click to expand...
Click to collapse
Hey Sleuth, does your cab include the schap's setupvoip program?
Hi guys,
I use Sleuth's WM6VoIP and Schap's Setup VoIP version 0.3, had no problems getting it to work, tested both WiFi and HSDPA. Only thing is that I have to use the headset or BT cause of the well known WM back speaker issue.
I have no problems connecting to company's PBX thru WiFi using VoIP Setup, can register and make calls.
When I use the OpenVPN to tunnel to corporate network my SIP softphone application keeps registring using the WiFi network card IP address, not the TAP VPN adapter's one. Therefore voice can't be routed correctly
1. Is there a way to choose which Network adapter to use when using Internet calling and VoIP Setup?
2. Can anyone recommend any other application that's 'smart' enough to have the option of selecting the network adapter to use?
Thanks,
T.
VOIP while connected via USB?
Is it possible to use voip on kaiser when the device is connected to Internet via active sync USB method? sounds stupid, but if there's this would b a good solution to use voip in office where certain ports are blocked in office wifi.
did anyone succeeded using voip through the normal phone speakr? (the ear speaker, not the music/loud speaker), preferably with the integrated wm6 voip?
if so, what is your rom type and version?
what is the size and date of your \windows\rtcdll.dll?
thanks.
not sure if any non real phone apps got access to that speaker
if it is possible then i believe that programs have to be written to use it
and skype being developd as a pda program rather then a pdaphone program
prob use the only speaker normal pda's got
i could be wrong though
maybe you can get it ot use a bluetooth headset with less hassel
HEllo,
I discovered yesterday the issue with the speaker and went through many forum but did not find any positive answer on how to get the sound directed to the good speaker.when using SIP.
I even did not understood if it is a problem of the touch cruise only or a general issue ...
Is the issue solvable - So I can still hope - or is there any hardware limitation
This issue means that using SIP with the Touch cruise is not possible except if we agree to have everyone in the room listening to the phone call ...
So if you have any positive information/solution ... Thank you
Franck
Search for a sip client agenet mobile or something. It's not exactly the name, but I can't dind it again. But this one is the only one that works at least on some of the smartphones with the earspeaker. And they want to add more supported devices in the future.
Generally it's a general problem, not a TC problem. The telcos just don't want a proper SIP integration in WM or they even deactivate it completely. It's a kind of squeeze to Microsoft. But MS won't disrespect them because they all like money.
Thank you for the answer.
I found Agephone mobile. Is it the one you were thinking about ?
I just tried it but no success, sound still come out through the rear speaker ...
Franck
Yeah, that's it. I've tried it right now as well but no luck. It's quite useless, as long as the ear speaker is not working. But it's not their blame. On the Trinity it's working allegedly.
Maybe we can them them a log. For some models they fix it.
phone speaker
it must work cause it works for me.
Hello papasieg,
Does it really work for you ? with the sound coming from the normal sound speaker and not the rear one ?
Take care that a trick exist with some SIP softphone which reduces the level on the rear sound speaker, giving the impression that it comes from the normal sound speaker but is is not the case ...
I am going to have another look at agephone
I had a discussion with eyepmedia (they produce eyepcommunicator). They answered:
Regarding our SIP softphone - eyeP Communicator for Windows Mobile – we have not yet made any certifications (nor tests) with the HTC Touch series. Until last year, previous HTC devices (HTC TyTN, 9100, etc) exposed a hardware bug which did not allow to handle the back and phone speakers correctly. But we hope this issue has been sorted out by HTC on new devices.
For information, we intend to make a new certification versus an HTC Touch Cruise before the end of the year. If your project has shorter timelines, then I suggest organizing a conf call to a date/time which works fine with you.
Franck
New test with Age phone
I made a new test with Agephone Version 2.63 (2008.08.28) and did not managed to have it working properly (I tried several configuration for the audio device).
So if someone has a working configuration ...
Sincerely,
Franck
Hi if someone can help me it would be much appreciated. I just bought a Touch Pro and everything is working fine....except for one really annoying issue.
Whenever I connect my bluetooth to a headset, it shows connected but no sound is coming out. The sound is muted. when connected to my Audi, I see that the phone has bars (shows connected and I can dial the phone), but when I make a call no sound. Similarly on my SE HBH-DS970 headset. The A2DP works perfectly, but when I make a call nothing.....I've searched google and through XDA and no solution.
Can someone suggest a solution? I've soft/hard reset the device already. If I should change Radio ROM which one would someone suggest that's stable? Thanks
If no one else has this problem, can anyone at least suggest to me if this sounds like a Hardware or software issue? If hardware I will return it, but if software I will try to find a solution. Like I said the phone connects to BT, but I just can't get handsfree to work. File transfers and A2DP work. Thanks
Just flashed to UK ROM and still no help....I've read some people having the same problems over at the Diamond thread...I'm the only one answering my own thread here hahaha....if anyone can help I'd greatly appreciate it. Thanks.
Hi,
I occasionally had such an issue with my Parrot CK3100, but I did not get the time yet to investigate further. After the call was connected I did not hear anything, and I am not sure whether the other party could hear me.
On another day, the handsfree was working perfectly OK.
Cheers
Michael
Thanks for replying Michael....I'm at a loss and I tried all the suggestions posted. I hope it's a software issue...I'm going to buy a bluetooth headset tomorrow and see if that works. It's not the end of the world, but annoying since all my ppc, s60, BB, and UIQ phones prior to the TP have not had any such issues.
Do you think it's a software issue?
have you tried playing music?
Yes.....A2DP works perfectly....no problems whatsoever with file transfers either....I'm guessing either it's a software problem or the phone has a new bluetooth software that's not agreeing with my older SE headset, but the car is another issue. The Car is 2007 and I'm sure the Bluetooth software is not that old. I've tried Euro WWE and Asian WWE ROM and no go.....I'm going to try the Cingular ROM and see what happens.
Just another quick update....I tried 2 other different bluetooth headsets and still the same problem... for some reason the sound for handsfree will not come through...anyone know of registry hack possibly that will allow sound to come through?
May not be entirely related to your problem...
Mine is worst...whenever I have paired my Jabra or iTech BT headset, when the phone rings, 8/10 times the phone will auto pickup (and no I did not setup the phone to auto pickup) and the it will NOT connect to the bluetooth. Instead it will be just like an auto pickup and the sound will come thru the phone headset. This is driving me nuts!!!!
Hi all
I have a fully unlocked (from purchase) P5100 tablet which has been rooted for openvpn support. I set up a bluetooth headest with it and everything was ok.
After a few days mobile originiated GSM voice is no longer working properly although mobile terminating seems to work fine .
GSM Speakerphone calls ring once on the tablet then go silent. and this is total "audio shut down" silent, no hiss no nothing, the call proceeds but when the call is picked up at the remote (B party) end , there is no voice path either way but DTMF tones can be inserted to line from the keypad.
GSM tablet originated calls made with a stereo headphone (i.e. expecting to listen to the call on headphone using the tablets internal microphone) give the same result as GSM speakerphone
GSM inbound calls to headphones work as expected
VOIP calls route as expected
tried turning off BT and WIFI , rebooting , unpairing the BT headset ...no restoration of audio !!
Well....i'm stumped !!! anyone got any clues ???
regards
CQU
for the record - I have checked the obvious like the "in call" volume was set to maximum not set to "0"
try Reset factory setting
Factory reset hasnt fixed it, going back to supplier as 'not fit for purpose" under the sale of goods act
Specifically wanted a 5100 for gsm voice calling
Regards
CQU
same problem...
Hi, I've got the same issue...
Even after flashing several custom roms I can make between 0 and 2 succesful outgoing gsm phone calls after a reboot.
Maybe anyone knows a radio rom that works properly in the netherlands? I'm hoping that that might solve the issue. Unfortunately, samsung hasn't released a new version for the netherlands yet as far as I know...