Related
Topic.
1: Volume rocker did not work properly.
2: Many scratches on the backplate.
3: loose screen causing clicking noise.
Twice.
#1 - Wifi died after a week.
#2 - Screen was completely detached on one side out of the box.
Almost returned my third since it looked like the spring was missing from my SD card slot (that is, the card went in with no resistance and wouldn't push in to pop out)... but on a whim I decided to try it again right before I finished boxing it back up and it started working.
Its a great tablet, but Asus really needs to improve their quality control.
ZROW
Returned mine no times...
Thought about it-didn't do it.
0 cakes out of infinity
did not return my tablet, was flawless unit
Did the Infinity even come with plastic covers for the keyboard dock connections and the charging port like the TF201 model? The Infinity I saw, brand new right out of the box there were no plastic protective covers at all.
opentoe said:
Did the Infinity even come with plastic covers for the keyboard dock connections and the charging port like the TF201 model? The Infinity I saw, brand new right out of the box there were no plastic protective covers at all.
Click to expand...
Click to collapse
All three of mine had the cover on the dock connector itself, but not the two slots where it connected to the dock.
Edit: Sigh... Now I"m considering returning mine for the third time. When I got it, I noticed the screen could be pushed in a little along the bottom, like it wasnt completely attached but I figured it'd be ok since it was just one spot. Now its doing it along the top. My local best buy has them in-store now so I could exchange it no problems, but I've been holding off during my return period before unlocking and I dont want to push that back again...
I heard you can get banned for 90 days from Best Buy if you return too much... They scan your driver's license to keep a log of your returns. Not sure if it applies to defective tablets but they will probably assume that you're doing the damage one day. Anyways, time to exchange it.
Zero. Slight clicking sound. GPS is a bit slow. Nothing else.
4: Loose screen, clicking noise
5: Loose screen, clicking noise
6: Loose screen, clicking noise
7: 5 pieces of dust under screen.
This is outrageous.
Vibrating Motor didn't work at all.
This one is perfect. Everything works great. No creeking of the screen, no light bleed no problems what so ever. For now.
4 times....... 1- had dust under screen, 2- dead pixels, 3-dust under screen 4-dead pixels again, and the one I currently have seems like a keeper, I am used to it already as I had to do the same for the Prime and tf300 at least twice, but once I got a good one it held up good, Im very satisfied with the one I currently have. the infinity is clearly a beast!
8: dusts under screen
Finally got a good one on my ninth... everything is good except for the minor lightbleed but IDC I have found THE ONE!
ImYoungxD said:
8: dusts under screen
Finally got a good one on my ninth... everything is good except for the minor lightbleed but IDC I have found THE ONE!
Click to expand...
Click to collapse
I highly doubt you can go through 9 units in 2 days. Are you near a real store?
le rustle face
Keion said:
I highly doubt you can go through 9 units in 2 days. Are you near a real store?
le rustle face
Click to expand...
Click to collapse
I live between two BB stores that are under 3 miles away.
I work in the city where two BB stores are less than 1 mile away so I can walk.
I also open the box in the store after exchanging and check for problems. If I do, I exchange it again. Started this after my fourth exchange cause I was getting annoyed driving back and forth.
wow. I feel lucky. I got mine first week available in North America and have NO issues. no dust, no light bleed. Been working great. No complaints, except with Chome being a big laggy.
Zero.
Original TF101 - 7 TIMES. Yup..dead pixels, blemishes on screen, dead WIFI, crappy QA until I got a good one.
TF201 - Twice. Dead pixels, dead GPS. End of romance.
TF700 - Returned once. Original one had cosmetic imperfections (large dark stain/spot on the side), loose screen and clicking on left side of screen. Picked up another one, PERFECTION. No dead pixels, no clicking, no cosmetic damage.
Zero. No problems in 3 weeks.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
wow
Really This is shocking to hear. I bought mine online from america, because I couldnt buy the cheaper speced version here. But mine is perfect thank god. I do actually have a very slight clicky sound in one of the corners. But I'll live with that. I don't really know what I could do if this craps out on me.
Asus really need to work on their QC...
No returns on my infinity yet, I have had mine for almost 30 days (have 60days for BB returns). Have a 2yr ADH from square trade just incase. Looks like this infinity is a keeper.
My primes on the other hand was just a QC problems after QC problems... very dissapointed with the prime.
My TF700 Screen (and digitzier) where shuttered (I left it on the car roof and drove, when I realized what I have done and drove back, I saw it on the road after a car drove over it).
Luckily, everything seems to works fine (connected it through HDMI and USB mouse) and aside some metal dents, it seems fully functional.
My question:
My digitizer flat cable has the marking "5184N FPC-1 REV: 3" while every LCD+digitizer combo out there has the marking "5184N FPC-1 REV: 2".
(Interestingly enough, when buying digitizer alone, there are planty of rev 3 ones).
Does it matter?
squigs said:
My TF700 Screen (and digitzier) where shuttered (I left it on the car roof and drove, when I realized what I have done and drove back, I saw it on the road after a car drove over it).
Luckily, everything seems to works fine (connected it through HDMI and USB mouse) and aside some metal dents, it seems fully functional.
My question:
My digitizer flat cable has the marking "5184N FPC-1 REV: 3" while every LCD+digitizer combo out there has the marking "5184N FPC-1 REV: 2".
(Interestingly enough, when buying digitizer alone, there are planty of rev 3 ones).
Does it matter?
Click to expand...
Click to collapse
Probably not. similar issues with TF300 was solved by flashing the touch screen firmware.
check this thread:
http://forum.xda-developers.com/showthread.php?t=2091233&page=11
NOTE: DO NOT update to 02-3011-4820.ekt firmware!!!
squigs said:
My TF700 Screen (and digitzier) where shuttered (I left it on the car roof and drove, when I realized what I have done and drove back, I saw it on the road after a car drove over it).
Luckily, everything seems to works fine (connected it through HDMI and USB mouse) and aside some metal dents, it seems fully functional.
My question:
My digitizer flat cable has the marking "5184N FPC-1 REV: 3" while every LCD+digitizer combo out there has the marking "5184N FPC-1 REV: 2".
(Interestingly enough, when buying digitizer alone, there are planty of rev 3 ones).
Does it matter?
Click to expand...
Click to collapse
Omg That is crazy!!! I glad it still works :angel: could you please post pictures of the damage (front and back)
This would be a good example thread for stress test and durability!
P.s. Dont feel bad i left a sony s tablet on the car roof once and a Nintendo DS lite on the bumper of a truck. :silly:
vadimbrk said:
Probably not. similar issues with TF300 was solved by flashing the touch screen firmware.
check this thread:
http://forum.xda-developers.com/showthread.php?t=2091233&page=11
NOTE: DO NOT update to 02-3011-4820.ekt firmware!!!
Click to expand...
Click to collapse
Thanks mate, will give it a go then (after I thoroughly read the referenced link, there's seem to be a lot of nuances there).
What's wrong with 02-3011-4820?
ronniereiff said:
Omg That is crazy!!! I glad it still works :angel: could you please post pictures of the damage (front and back)
This would be a good example thread for stress test and durability!
P.s. Dont feel bad i left a sony s tablet on the car roof once and a Nintendo DS lite on the bumper of a truck. :silly:
Click to expand...
Click to collapse
Sure, here are some pictures, I hope my s2 camera can communicate the subtle dents, if not, I can later take some shots with a real camera.
(Note that I opened the tablet, you'll notice at the upper right corner what seems like a seperation of the metal casing, it's not, I just placed the screen on top loosely to take the pictures).
I also posted the sleeve the TF700 was in during "the incident". The wheel marks off the case are already gone, but back then I tried to measure them against my car's wheel, and they where almost the same width, so I assessed (maybe wrongfully?) that it matches roughly a mid-size family car (I drive a Renault Fluence).
Solved - YAY
I thought I'd post an epilog...
I've ordered and received the replacement panel, set me back ~129 USD (including shipping)
(Ordered from Aliexpress.com).
Replacement require you to be super gentle, those little hinges on the connector will break super-easly, do not apply for to them, they should be lifted up to remove the cable and pressed down to secure it.
Since the metal casing got dents hear and there, the screen doesn't sit 100% (you'll notice it in the picture) but it's really not too bad.
(I could of course try and re-dent it so it fits more tightly in, maybe I will do so eventually).
All in all, it was a positive experience, everything works smooth, screen looks great, I personally can't tell any diff from the original screen in term of sharpness, colors, brightness etc.
Best regards.
squigs said:
I thought I'd post an epilog...
I've ordered and received the replacement panel, set me back ~129 USD (including shipping)
(Ordered from Aliexpress.com).
Replacement require you to be super gentle, those little hinges on the connector will break super-easly, do not apply for to them, they should be lifted up to remove the cable and pressed down to secure it.
Since the metal casing got dents hear and there, the screen doesn't sit 100% (you'll notice it in the picture) but it's really not too bad.
(I could of course try and re-dent it so it fits more tightly in, maybe I will do so eventually).
All in all, it was a positive experience, everything works smooth, screen looks great, I personally can't tell any diff from the original screen in term of sharpness, colors, brightness etc.
Best regards.
Click to expand...
Click to collapse
I have the exact same problem. I took mine apart and see that mine too is marked ""5184N FPC-1 REV: 3". Which part did you actually purchase? I went on aliexpress and it looks like rev 3 is no longer available. Wondering if other revs would work.
i would like to if it is possible to use the 5184N FPC-1 REV: 2 when orginally it was a 5184N FPC-1 REV: 3. Will it work in the tablet
Did it work?
goodwinxda said:
I have the exact same problem. I took mine apart and see that mine too is marked ""5184N FPC-1 REV: 3". Which part did you actually purchase? I went on aliexpress and it looks like rev 3 is no longer available. Wondering if other revs would work.
Click to expand...
Click to collapse
Hi, Did anyone find out if a REV2 digitizer will work in place of the REV3?
Thanks!
-Dave
Have similar problem with revision number.
My TF700 has TCP10D47 rev V.02, but on ebay available only v0.1.
Some sellers wrote in item description that v.01 and v0.2 are compatible, some that not compatible.
Does anyone have information about revision compatibility ?
Anthony2002 said:
Have similar problem with revision number.
My TF700 has TCP10D47 rev V.02, but on ebay available only v0.1.
Some sellers wrote in item description that v.01 and v0.2 are compatible, some that not compatible.
Does anyone have information about revision compatibility ?
Click to expand...
Click to collapse
I rolled those dice. The v.01 worked in place of my v.02 without issue. The worst was waiting for the part.
Sent from my ASUS Transformer Pad TF700T using Tapatalk 2
Going to try it!
Anthony2002 said:
Have similar problem with revision number.
My TF700 has TCP10D47 rev V.02, but on ebay available only v0.1.
Some sellers wrote in item description that v.01 and v0.2 are compatible, some that not compatible.
Does anyone have information about revision compatibility ?
Click to expand...
Click to collapse
Hi Guys,
I have a source for revision 3.0 but they want $129.00CAD each, I am going to try a Revision 2 on this tablet and I will post back my findings.
-Dave
compatibility
I can confirm that the "5184N FPC-1 REV: 2" works on tablets that have a broken "5184N FPC-1 REV: 3" digitizer. Just fixed mine and it touching perfectly.
davae93 said:
I can confirm that the "5184N FPC-1 REV: 2" works on tablets that have a broken "5184N FPC-1 REV: 3" digitizer. Just fixed mine and it touching perfectly.
Click to expand...
Click to collapse
No need to flash anything, just remove the old, connect the new, power up and everything works?
My wife stepped on my TF700 (my fault, had it on the floor next to our bed, she came in and it was pitch dark...).
I have just cracked it open by the help from the tool set and instructions on ifixit.com, and noticed the digitizer is a Rev 3, but the ebay and aliexpress are Rev 2.
So if I understand you correctly, I should just go ahead and buy one of the 5184 fpc 1 Rev 2 digitizers and install it as soon as it arrives...
Thanks,
Christopher
grenness said:
No need to flash anything, just remove the old, connect the new, power up and everything works?
My wife stepped on my TF700 (my fault, had it on the floor next to our bed, she came in and it was pitch dark...).
I have just cracked it open by the help from the tool set and instructions on ifixit.com, and noticed the digitizer is a Rev 3, but the ebay and aliexpress are Rev 2.
So if I understand you correctly, I should just go ahead and buy one of the 5184 fpc 1 Rev 2 digitizers and install it as soon as it arrives...
Thanks,
Christopher
Click to expand...
Click to collapse
Yes that is correct the 5184 focus rev 2 will work on your tablet. Based on what happened it seems your LCD is fine so you are in luck. There is a thin plastic frame between the LCD (led) and digitizer. Use a hair dryer to melt the glue so you can remove the LCD first then try to remove all the cracked glass off the frame. Its very time consuming so be patient. Remember to also buy some two sided sticky tape to seal the new digitzer back into place.
Good luck!!
aliexpress screen source?
shatz said:
For a couple days, programmer from Russia will make driver or something else, which will have invert X+/X- for this digitiser, but he say me, that this driver need to be included in ROM. And i will need to install this rom to my Asus tf201.
Who will can help include this driver to ROM???
Click to expand...
Click to collapse
squigs said:
I thought I'd post an epilog...
I've ordered and received the replacement panel, set me back ~129 USD (including shipping)
(Ordered from Aliexpress.com).
Replacement require you to be super gentle, those little hinges on the connector will break super-easly, do not apply for to them, they should be lifted up to remove the cable and pressed down to secure it.
Since the metal casing got dents hear and there, the screen doesn't sit 100% (you'll notice it in the picture) but it's really not too bad.
(I could of course try and re-dent it so it fits more tightly in, maybe I will do so eventually).
All in all, it was a positive experience, everything works smooth, screen looks great, I personally can't tell any diff from the original screen in term of sharpness, colors, brightness etc.
Best regards.
Click to expand...
Click to collapse
can you please share the aliexpress supplier for the touch screen glass? my 3 year old tossed my pad like a Frisbee and need to replace.
How about replacing a Rev 3 with an 01?
I purchased a Rev 2 to replace my Rev 3 a month ago, it worked perfect - until today when my 9 month old daughter pulled the tablet down from the table by the charge cable. It apparantly landed on the corner so the digitizer is once again cracked.
To my surprise the price of the Rev 2 digitizers seems to have gone up by 3X, at least on eBay.
Rev 1 (or .01, or 0.1) are still reasonably priced.
Can I go for a Rev 1 for my tablet who originally had a Rev 3 that was successfully replaced by a Rev 2?
Has anyone tried?
Thanks,
Christopher
Rev 3 available from eBay @ $110:
http://www.ebay.com/itm/400623625242
Just ordered, seller has 2 left.
I just scanned aliexpress, no Rev 3 or Rev 2 (0.2) available (at least not for sane amounts of $$).
Sorry to dig up an old thread, but finding an answer to my problem I think this is the best bet.
I have a rev 2 that according to the ASUS repair centre needed to be replaced as I experienced sporadic touch registrations on the screen from time to time. On-line I could only find the rev 3 digitizer and after reading someone used a .2 to replace a .3 I figured it would work.
So after the long wait finally arrived and I went though the pain-staking process of removing the old LCD and .2 digitizer.
But ever since installing the .3 it detects very little to no input.
I plugged the old one back in and just left it hanging to the side and that seems to be working, but strange no go with the new one.
Someone mentioned a firmware a few posts back, is this something I need to look more into for compatibility with the rev .3?
Thanks!
Hi, i am in desperate need of a lcd display for a 7 pro but they are seriously hard to get hold of!
I have looked on ebay and theres only ones from HK or China and even then the sellers feedback on screens is poor!
I have phoned countless repair shops in the uk and only a couple claim to be able to get hold of the screen but then demand that they fix the phone themselves and a stupid fee and will not supply the screen to me.
one thing i have noticed it that the touch pro 2 and 7 pro screens look identical apart from the colour of the ribbon that connects them to the main cable that goes through the slide body.
there is no visual difference between the screens or connector cables other thab colour and they have the same specs also-
480 x 800 pixels, 3.6 inches and a 259 ppi pixel density
Does anyone know if they are actually interchangeable or not? i cant find a screen anywhere and my wife is not pleased with me right now as ive only just got the phone and a broke the lcd trying to remove the digitizer even though i was ultra carefull and used lots of heat, please can someone help!!!!
Thanks, Steve.
Hello! To most simply answer your question, no. The screens are very different despite looking similar. The old TP2 screen is not multitouch and WP7 requires this. Also, the old screen utilizes a stylus while the newer 7 pro screen doesn't even recognize that type of touch.
It is your phone after all, so if you would like to try this that's your choice. However its too much effort to affix the ribbon to the pcb to even make it worth it. My old TP2 has a cracked digitizer which I have a replacement for, but the ribbon is machine pressed onto the pcb and reattaching this connection would be very difficult without the type of heat/pressure used in the manufacturing of the phone.
If you decide to try it let us know the results!
I'm sorry, I just seen you said the lcd itself, I thought you were meaning the digitizer screens.
That being said, maybe the swap will work, as long as they hook up the same?
x_orange90_x said:
I'm sorry, I just seen you said the lcd itself, I thought you were meaning the digitizer screens.
That being said, maybe the swap will work, as long as they hook up the same?
Click to expand...
Click to collapse
i found a seller with genuine touch pro 2 screens who is willing to take it back if it does not work for me, i will let everyone know if it works!
I can confirm, the touch pro 2 screen does NOT work in the 7 pro, it is almost identical but the conector is at most 1mm wider than the 7 pro but its enough to stop if fitting into the socket
Back to the drawing board for me i guess.
steve_htc_wizard said:
I can confirm, the touch pro 2 screen does NOT work in the 7 pro, it is almost identical but the conector is at most 1mm wider than the 7 pro but its enough to stop if fitting into the socket
Back to the drawing board for me i guess.
Click to expand...
Click to collapse
not sure if you still need an LCD, or maybe you got a new phone by now. I found this if your still interested in getting it up and going again.
http://www.ebay.com/itm/271230982583
x_orange90_x said:
not sure if you still need an LCD, or maybe you got a new phone by now. I found this if your still interested in getting it up and going again.
http://www.ebay.com/itm/271230982583
Click to expand...
Click to collapse
not been on for a few days, thankyou for the link its still there and in europe!
I bought another 7 pro handset as i could not wait any longer, i had been forced back to my old Touch pro (raphael) and although not a bad phone and running a custom 6.5.3 rom , it just cant cope on the web anymore as all the standards have changed and nobody is supporting windows mobile anymore.
Its a shame cos windows mobile is by far a better operating system than windows phone, updated and running on better hardware it would have rocked.
even though i bought a new handset ive always intended on fixing the other one when i get the chance and have put a bid on that screen to remove the buy it now.
Fingers crossed that it dont go up in price, my wife will kill me if spend much more on these phones lol
once its fixed its going to go in its box and live in a safe place till ive worn out this new one, dont think i wll sell it, thanks for your help, you get a thanks meter point for this :good:
Steve.
You are welcome I was a little worried you might not get to the link fast enough but thankfully you did! I seen that and figured its a steal considering the lcd is nearly that price alone, plus all the work needed to change it. Good luck I hope you win it
Thanks geeze
x_orange90_x said:
You are welcome I was a little worried you might not get to the link fast enough but thankfully you did! I seen that and figured its a steal considering the lcd is nearly that price alone, plus all the work needed to change it. Good luck I hope you win it
Click to expand...
Click to collapse
hey orange, i won that screen, got it for the starting bid, its on its way here at the moment, there was a delay in paying for it as my card decided bit to work on pay pal grrrr but its all sorted now, just gotta wait.
thanks again.
Hey guys a little question I have my old galaxy tab 7.0 plus which Samsung wont repair no reason can i just buy a 7in screen and repair it my self since there are many screens here in Philippines
Sent from my GT-P6800 using XDA Premium 4 mobile app
captsingh787 said:
Hey guys a little question I have my old galaxy tab 7.0 plus which Samsung wont repair no reason can i just buy a 7in screen and repair it my self since there are many screens here in Philippines
Sent from my GT-P6800 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
as long as you get the right screen, theres no reason why you cant do it yourself, just go slow, very slow, read tutorials and be very carefull of all cables and boards inside. if it its the glass digitizer that is broken and not the whole display, be very very carefull when removing it from the lcd as theres a big chance of breaking the lcd as its removed, heat to relax the glue is your friend! if the glass is shatterd, removing the glass bit by bit instead of trying to remove it all at once may proove easyer and less risky on the lcd.
Good luck, steve.
Look at this auction: http://www.ebay.pl/itm/HTC-7-pro-Arrive-T7576-LCD-Display-/141028832234?pt=UK_Replacement_Parts_Tools&hash=item20d5f933ea&_uhb=1 this is display for 7 Pro.
Hey y'all
Has anybody tried upgrading the standard ROG phone 5 to add the OLED ROG vision display?
There are solder points for the OLED screen ribbon cable header on the PCB on the standard version but it's missing. I've got the necessary tools so the way I see it, solder on a connector (assuming I can find one), pick up a replacement back with the OLED screen and see what happens.
Does this sound too crazy?
Kris
It'd be super cool to see if it can be done since the versions share the same rom package. Which means it probably does already have the code for the screen
I'm comfortable soldering surface mount components so the only trick would be sourcing the parts. In my enquiries this far I've not been able to confirm that the rest glass replacement comes with the OLED screen.
I've also not been able to source the connector for the ribbon cable.
If software is the same, I can't imagine why it wouldn't work. I'm definitely keen to give it a red hot crack.
yurishouse said:
It'd be super cool to see if it can be done since the versions share the same rom package. Which means it probably does already have the code for the screen
Click to expand...
Click to collapse
The drivers are there. I remember seeing them.
Hi all, my wife cracked and broke the screen on her pixel 4a. For a while it worked fine, and then one day the screen just would not turn on any more.
You can tell the phone boots up because if I connect it to a PC it did recognize it's a pixel4a, and when you touch the fingerprint sensor on the back it vibrates.
I tried a usbc hub and connected HDMI and a mouse to the hub but can't get anything to display on the TV. (Tested these on my OnePlus 9 confirmed working there) On the OnePlus I immediately see a lock screen on the TV and can use the mouse to interact but with the pixel I get nothing.
Is there any other way into the phone?
I'm really not sure it's worth the $140-$200 repair costs especially when a refurb costs similar.
I thought about the pixel6a trade up program but I don't know if it will qualify (requirements were a bit unclear )
ltk6260 said:
Hi all, my wife cracked and broke the screen on her pixel 4a. For a while it worked fine, and then one day the screen just would not turn on any more.
You can tell the phone boots up because if I connect it to a PC it did recognize it's a pixel4a, and when you touch the fingerprint sensor on the back it vibrates.
I tried a usbc hub and connected HDMI and a mouse to the hub but can't get anything to display on the TV. (Tested these on my OnePlus 9 confirmed working there) On the OnePlus I immediately see a lock screen on the TV and can use the mouse to interact but with the pixel I get nothing.
Is there any other way into the phone?
I'm really not sure it's worth the $140-$200 repair costs especially when a refurb costs similar.
I thought about the pixel6a trade up program but I don't know if it will qualify (requirements were a bit unclear )
Click to expand...
Click to collapse
There is no way inside other than removing the screen and replacing it, they are a bit tricky I have done several of them , the big expense is the screen, they are not cheap, I get mine from China where they cost about 50 - 100 less then the U.S , and your right it would not qualify for the full 300 trade in though u may get something, You could try selling it on eBay hoping who ever bought it would do a factory reset once repaired, or if it is google locked even a reset won't unlock it the pin needs to be given before setup can begin.
Darn that's what I was afraid of. I wonder why the usbC to HDMI doesn't work on the pixel but does work on my OnePlus
ltk6260 said:
Darn that's what I was afraid of. I wonder why the usbC to HDMI doesn't work on the pixel but does work on my OnePlus
Click to expand...
Click to collapse
I read somewhere that Google are pushing their streaming through Chromecast. By blocking all your other options, they give you no choice but to do it their way. I have also read that the hardware is physically capable, just blocked in the firmware.
Gah that's such a shame. usbc to a hub is such a cool/useful utility function to have.
found this, but looks like only specific docks work and would have had to install the app previously https://support.google.com/pixelphone/answer/2865484?hl=en
hammered58 said:
I get mine from China where they cost about 50 - 100 less then the U.S
Click to expand...
Click to collapse
Can you please provided a link to the supplier you bought from? I broke my screen and I'm back on my Pixel 2 XL last used about 2 1/2 years ago which is working surprisingly well so I'm not in a hurry to get the new screen.
dsteinschneider said:
Can you please provided a link to the supplier you bought from? I broke my screen and I'm back on my Pixel 2 XL last used about 2 1/2 years ago which is working surprisingly well so I'm not in a hurry to get the new screen.
Click to expand...
Click to collapse
Yes the company is ali express, lots of screens, I actually have purchased the blemished screens which are perfectly good enough for me,
Thanks for the info. I've bought parts on Ali Express - I'll check out the Pixel 4a 4G screens on there. Is the blemish a dead pixel? I'm good with that.
hammered58 said:
Yes the company is ali express, lots of screens, I actually have purchased the blemished screens which are perfectly good enough for me,
Click to expand...
Click to collapse
Didn't notice blemished ones for sale and this new one that appears to be "OEM" (or close enough) was $71. I also found a coupon for new Ali Express purchasers so I got another 10 percent off.
https://www.aliexpress.us/item/3256805015947644.html?spm=a2g0o.productlist.main.1.62901c2ce2CayF&algo_pvid=65e4dfea-cfa8-4304-bd57-4d7804a61096&algo_exp_id=65e4dfea-cfa8-4304-bd57-4d7804a61096-0&pdp_npi=3%40dis%21CAD%21248.37%2199.35%21%21%21%21%21%40211bf04a16847644372762663d07a0%2112000032133795938%21sea%21US%212631249338&curPageLogUid=GgFKBSed0rzk