Database Info

bricked my huawei Mate 8 NXT-L29 after flash plzz HELP

bricked my huawei Mate 8 NXT-L29 after flash plzz HELP :crying:

[email protected] said:
bricked my huawei Mate 8 NXT-L29 after flash plzz HELP :crying:
Click to expand...
Click to collapse
Follow instructions here: http://forum.xda-developers.com/mate-8/development/rayglobe-italian-knife-t3295526 you should be up and running after.

First check if u can enter into recovery with the vol-up+power combo

additional info would also be nice as to what exactly u did...
Sent from my Huawei Mate 8 NXT-AL10 using Tapatalk

Hi all, I have a problem with my mate8 ... after I installed TWRP next rom (NXT-L29C432B170) can not just write anything in fastboot. I fastboot unlocked but not take any order. I can not do root. I can not flash custom recovery. I can not flash another rom. I can not change themes. Help me please.

I'm going through the same problem .. and I've tried all possible methods I found on internet but nothing worked for me ..
now my phone situation is:
I can maximum go to fastboot or Huawei eRecovery mode ..
on Fastboot:
I tried to use italian knife to; unbrick, install recovery but nothing worked ..
on Huawei eRecovery:
I connect with my wifi but after few searches or loading it give the error ..
I tried Huawei PC software it says I can't use system recovery ...
First I was able to go to TWRP recovery and there I tried different custom and stock roms to flash but after flash it was giving 'System is booting now....' and stays here and when I tried to resolved it, I lost my TWRP recovery too ... now I've nothing except fastboot and Huawei eRecovery ... can anybody please help us all ..?

muqaddas_dunyatv said:
I'm going through the same problem .. and I've tried all possible methods I found on internet but nothing worked for me ..
now my phone situation is:
I can maximum go to fastboot or Huawei eRecovery mode ..
on Fastboot:
I tried to use italian knife to; unbrick, install recovery but nothing worked ..
on Huawei eRecovery:
I connect with my wifi but after few searches or loading it give the error ..
I tried Huawei PC software it says I can't use system recovery ...
First I was able to go to TWRP recovery and there I tried different custom and stock roms to flash but after flash it was giving 'System is booting now....' and stays here and when I tried to resolved it, I lost my TWRP recovery too ... now I've nothing except fastboot and Huawei eRecovery ... can anybody please help us all ..?
Click to expand...
Click to collapse
Try the followings:
1) download the update.zip from: http://forum.xda-developers.com/mate-8/general/huawei-mate-8-stock-firmware-official-t3391727
2) Extract UPDATE.APP
3) Create a folder dload on a SD card and put it in the phone
4) Push the power+volume up+volume down at the same time
If it works the phone will run the UPDATE.APP and you will be back with the stock rom.
---------- Post added at 02:39 PM ---------- Previous post was at 02:36 PM ----------
muqaddas_dunyatv said:
I'm going through the same problem .. and I've tried all possible methods I found on internet but nothing worked for me ..
now my phone situation is:
I can maximum go to fastboot or Huawei eRecovery mode ..
on Fastboot:
I tried to use italian knife to; unbrick, install recovery but nothing worked ..
on Huawei eRecovery:
I connect with my wifi but after few searches or loading it give the error ..
I tried Huawei PC software it says I can't use system recovery ...
First I was able to go to TWRP recovery and there I tried different custom and stock roms to flash but after flash it was giving 'System is booting now....' and stays here and when I tried to resolved it, I lost my TWRP recovery too ... now I've nothing except fastboot and Huawei eRecovery ... can anybody please help us all ..?
Click to expand...
Click to collapse
In step 3 you need to put the UPDATE.APP in the dload folder.

[email protected] said:
Try the followings:
1) download the update.zip from: http://forum.xda-developers.com/mate-8/general/huawei-mate-8-stock-firmware-official-t3391727
2) Extract UPDATE.APP
3) Create a folder dload on a SD card and put it in the phone
4) Push the power+volume up+volume down at the same time
If it works the phone will run the UPDATE.APP and you will be back with the stock rom.
---------- Post added at 02:39 PM ---------- Previous post was at 02:36 PM ----------
In step 3 you need to put the UPDATE.APP in the dload folder.
Click to expand...
Click to collapse
I have try but still cannot done . I think I'm wrongly flash other version.
What can i do???

Raymondpop said:
I have try but still cannot done . I think I'm wrongly flash other version.
What can i do???
Click to expand...
Click to collapse
Try to dload the update.app from the rollback package from this website:
http://forum.xda-developers.com/mate-8/general/best-easiest-to-rollback-to-emui-4-0-t3507399
Try all three to see which one works for you. If the rollback update.app works then you can dload the update.app for the firmware you used before.

2G/3G not working: Version of Marshmallow B831

Hi. Earlier I had lollipop version of android on my Honor 6 phone. A month back, I upgraded to Marshmallow version B831. Since then, I am not able to connect to mobile data. 2G/3G is not working on my phone. Please let me know what should I do.
Also if I navigate to About Phone ->>Status, I can see that Mobile data state is saying as Disconnected.

I think you should back up and do a phone reset

goldfinv said:
I think you should back up and do a phone reset
Click to expand...
Click to collapse
I did it yesterday. Is it possible to go back to Lollipop?

iamsonal said:
I did it yesterday. Is it possible to go back to Lollipop?
Click to expand...
Click to collapse
Yes. Download the full update package, then download HuaweiUpdateExtractor
Then. Download Multi tool
And run. Select U to Unbrick. Follow the on-screen instructions to extract the required files from the UPDATE package downloaded. Copy to the Unbrick folder and continue the process. Your phone should be on lollipop at the end.

goldfinv said:
Yes. Download the full update package, then download HuaweiUpdateExtractor
Then. Download Multi tool
And run. Select U to Unbrick. Follow the on-screen instructions to extract the required files from the UPDATE package downloaded. Copy to the Unbrick folder and continue the process. Your phone should be on lollipop at the end.
Click to expand...
Click to collapse
Is there any tutorial step by step to perform the downgrade process to Lollipop version?

Yes. There are a few in the forums

@iamsonal follow this if you don't want to use Multi Tool
Extract system.img, boot,img, cust.img, recovery.img from the UPDATE.APP using Huawei Update Extractor tool
Flash those files by first booting your device into fastboot mode, and then firing these commands:
Code:
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash recovery recovery.img
Remember that the command should be executed from the folder where these files are there.
After doing this do the three button update using that UPDATE.APP from which you extracted these files.

DigiGoon said:
@iamsonal follow this if you don't want to use Multi Tool
Extract system.img, boot,img, cust.img, recovery.img from the UPDATE.APP using Huawei Update Extractor tool
Flash those files by first booting your device into fastboot mode, and then firing these commands:
Code:
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash recovery recovery.img
Remember that the command should be executed from the folder where these files are there.
After doing this do the three button update using that UPDATE.APP from which you extracted these files.
Click to expand...
Click to collapse
When I fire this command
fastboot devices
It opens a screen with android logo, saying PHONE Locked. Will I be able to fire the fastboot commands?

iamsonal said:
When I fire this command
fastboot devices
It opens a screen with android logo, saying PHONE Locked. Will I be able to fire the fastboot commands?
Click to expand...
Click to collapse
Nope, you have to unlock your bootloader first.
---------- Post added at 07:48 PM ---------- Previous post was at 07:45 PM ----------
Do you have the Unlock Code bro???

DigiGoon said:
Nope, you have to unlock your bootloader first.
---------- Post added at 07:48 PM ---------- Previous post was at 07:45 PM ----------
Do you have the Unlock Code bro???
Click to expand...
Click to collapse
No. What should I do now?

iamsonal said:
No. What should I do now?
Click to expand...
Click to collapse
Don't worry follow this guide to unlock your bootloader first.
WARNING: UNLOCKING BOOTLOADER WILL WIPE YOUR DATA AND YOUR WARRANTY WILL GET VOID.

DigiGoon said:
Don't worry follow this guide to unlock your bootloader first.
WARNING: UNLOCKING BOOTLOADER WILL WIPE YOUR DATA AND YOUR WARRANTY WILL GET VOID.
Click to expand...
Click to collapse
Thanks. Let me check.

iamsonal said:
Thanks. Let me check.
Click to expand...
Click to collapse
Good luck.

Nothing

iamsonal said:
Nothing
Click to expand...
Click to collapse
What do you mean?

DigiGoon said:
What do you mean?
Click to expand...
Click to collapse
I mean when I am trying to press the 3 buttons simultaneously, it only displays the Honor booticon. It doesn't display any other screen.

iamsonal said:
I mean when I am trying to press the 3 buttons simultaneously, it only displays the Honor booticon. It doesn't display any other screen.
Click to expand...
Click to collapse
You put UPDATE.APP in dload folder of your External SDCARD no?

DigiGoon said:
You put UPDATE.APP in dload folder of your External SDCARD no?
Click to expand...
Click to collapse
I had. But I think it might have been deleted while unlocking bootloader. Is there any fastboot push command?

Honor 8 Bricked

Hello everyone,
I'm actually in front of a big problem. I try this night to upgrade from FRD-L09C432B120 to FRD-L09C432B316. Since I try it, my phone stay on a Warning screen and i can't do anything. (Just try to shut down by a long press on power button and it make a reboot and it's the same for every key combination).
I can't go in Recovery or eRecovery. The only things that works is the fastboot mode. I try to flash the stock firmware after an extract of "UPDATE.APP" but the system image give me an error. I also try to put UPDATE.APP on the SD Card but I can't access to the update mode (by press vol+ , vol- and power button). I think that i've try all the ideas that i've fund on internet !
I've no more ideas. Do you think that is possible to unbrick it ?
Thanks to your help and your reply.

Flo.B said:
Hello everyone,
I'm actually in front of a big problem. I try this night to upgrade from FRD-L09C432B120 to FRD-L09C432B316. Since I try it, my phone stay on a Warning screen and i can't do anything. (Just try to shut down by a long press on power button and it make a reboot and it's the same for every key combination).
I can't go in Recovery or eRecovery. The only things that works is the fastboot mode. I try to flash the stock firmware after an extract of "UPDATE.APP" but the system image give me an error. I also try to put UPDATE.APP on the SD Card but I can't access to the update mode (by press vol+ , vol- and power button). I think that i've try all the ideas that i've fund on internet !
I've no more ideas. Do you think that is possible to unbrick it ?
Thanks to your help and your reply.
Click to expand...
Click to collapse
But please confirm , was the update from b120 to b316 successfull?
Sent from my KIW-L22 using Tapatalk

gopinaidu77 said:
But please confirm , was the update from b120 to b316 successfull?
Click to expand...
Click to collapse
I think it failed because the warning screen showed right?
Sent from my honor 5X using XDA Labs

adriansticoid said:
I think it failed because the warning screen showed right?
Click to expand...
Click to collapse
Right that was what I am also thinking bro.
---------- Post added at 01:35 PM ---------- Previous post was at 01:35 PM ----------
adriansticoid said:
I think it failed because the warning screen showed right?
Sent from my honor 5X using XDA Labs
Click to expand...
Click to collapse
So it's a failure . which mean that it is a semi flashed update . which doesn't installed update.app .
Extract update.app from ota and put it in dload folder .later flash it manually using dload method .
He should follow this way to overcome those reboots
Sent from my KIW-L22 using Tapatalk
---------- Post added at 01:36 PM ---------- Previous post was at 01:35 PM ----------
Flo.B said:
Hello everyone,
I'm actually in front of a big problem. I try this night to upgrade from FRD-L09C432B120 to FRD-L09C432B316. Since I try it, my phone stay on a Warning screen and i can't do anything. (Just try to shut down by a long press on power button and it make a reboot and it's the same for every key combination).
I can't go in Recovery or eRecovery. The only things that works is the fastboot mode. I try to flash the stock firmware after an extract of "UPDATE.APP" but the system image give me an error. I also try to put UPDATE.APP on the SD Card but I can't access to the update mode (by press vol+ , vol- and power button). I think that i've try all the ideas that i've fund on internet !
I've no more ideas. Do you think that is possible to unbrick it ?
Thanks to your help and your reply.
Click to expand...
Click to collapse
Consider reading my above post bro.
Sent from my KIW-L22 using Tapatalk

HONOR 8 Bricked
Hello ,
It happened on my FRD-L04, but I think is the same.
Bootloader is unlocked ?
1. Do you have all drivers installed ? OK
2.Do you have STOCK ROM ? OK. If not, use Huawei Firmare Finder to find suitable ROM. Be aware what you choose !!!
3. Unzipp (WinRar) the ROM.
4.Download and install Huawei Update Extractor. Run Huawei Update Extractor . Choose Update.app from the folder you unzipped the ROM.
5. Select cust.img , boot.img , recovery.img and system.img and extract them on a folder.
6.. Install MultiTool by Team (Multi Tool Team). The instalation will make a folder named UNBRICK.
7. Move the files extracted : cust.img , boot.img , recovery.img and system.img on the folder UNBRICK
8. Run MultiTool . Choose option 6 (unbrick) and after that choose option 2 ( if you already have files on folder UNBRICK)
9. Let the tool finish the job.
NOTE : You must have all drivers installed and the phone in FASTBOOT mode ( turn phone OFF - Press VOL- and insert USB cable simultaneously.)
Good luck !

Hi, thanks everyone for your reply.
Unfortunatly, the dload method seems not work. I think that to run this method, i need to press simultaneously vol+, vol- and the power button to run it, right ?
If it's like that, the method doesn't work anymore.
I will try the process given by technoguy09 and I said to you if it's ok !

So, after many try, every method that i try doesn't work.
Even the Unbrick method doesn't work because the system and cust report an error.
For the cust, i have "partition error" and for the system I have the "sparse flash write failure". Can we correct this error ?

Flo.B said:
So, after many try, every method that i try doesn't work.
Even the Unbrick method doesn't work because the system and cust report an error.
For the cust, i have "partition error" and for the system I have the "sparse flash write failure". Can we correct this error ?
Click to expand...
Click to collapse
Was the bootloader unlocked ?
Do u have twrp installed ?
Sent from my KIW-L22 using Tapatalk
---------- Post added at 03:53 PM ---------- Previous post was at 03:53 PM ----------
Flo.B said:
Hi, thanks everyone for your reply.
Unfortunatly, the dload method seems not work. I think that to run this method, i need to press simultaneously vol+, vol- and the power button to run it, right ?
If it's like that, the method doesn't work anymore.
I will try the process given by technoguy09 and I said to you if it's ok !
Click to expand...
Click to collapse
If u have twrp I will make a flashable zip of stock ROM and cust
Sent from my KIW-L22 using Tapatalk

The bootloader is unlock and TWRP was install but now I can't access it. I try to restore stock recovery and it's the same result.

Flo.B said:
The bootloader is unlock and TWRP was install but now I can't access it. I try to restore stock recovery and it's the same result.
Click to expand...
Click to collapse
Can fastboot detect your phone?

Yes, fastboot is detect, I can launch some command (fastboot devices display my phone, flash etc) everything work but flash recovery didn't change anything and flash system response an error (sparse flash write failure).

Flo.B said:
Yes, fastboot is detect, I can launch some command (fastboot devices display my phone, flash etc) everything work but flash recovery didn't change anything and flash system response an error (sparse flash write failure).
Click to expand...
Click to collapse
From what you said, looks like it is reallt bricked. Service center is your friend.

I think too... I hope that there will be no problem with service center because of the phone is unclocked !
I was never had this kind of problem with my previous android phone. I'm really bad ^^
Thanks for all everybody.

Flo.B said:
So, after many try, every method that i try doesn't work.
Even the Unbrick method doesn't work because the system and cust report an error.
For the cust, i have "partition error" and for the system I have the "sparse flash write failure". Can we correct this error ?
Click to expand...
Click to collapse
Try another ROM.

Flo.B said:
I think too... I hope that there will be no problem with service center because of the phone is unclocked !
I was never had this kind of problem with my previous android phone. I'm really bad ^^
Thanks for all everybody.
Click to expand...
Click to collapse
Goodluck with it buddy.

technoguy09 said:
Try another ROM.
Click to expand...
Click to collapse
I try at least 3 ROM download on different website. I don't think that it can change anything.

I had the same problem.
Dont worry, Honor 8 phones are nearly unbrickable.
Take your B120 ROM extract recovery, cust and boot partitions. (use huawei update extractor)
Flash Them via fastboot (adb) then force the dload method via the 3 buttons combo.
I had all the problems you described and restored my phone as new. (even the "sparse flash write failure" error)
Now i'm on EMUI 5 rooted, no problem
---------- Post added at 06:30 PM ---------- Previous post was at 06:25 PM ----------
Please refer this thread as it might help you.
http://forum.xda-developers.com/mate-8/general/fuss-debrick-restore-mate-8-t3457969
Have a little faith in your Honor

Flo.B said:
I try at least 3 ROM download on different website. I don't think that it can change anything.
Click to expand...
Click to collapse
Did you use Huawei Firmare Finder for your model ?

morpheus302 said:
I had the same problem.
Dont worry, Honor 8 phones are nearly unbrickable.
Take your B120 ROM extract recovery, cust and boot partitions. (use huawei update extractor)
Flash Them via fastboot (adb) then force the dload method via the 3 buttons combo.
I had all the problems you described and restored my phone as new. (even the "sparse flash write failure" error)
Now i'm on EMUI 5 rooted, no problem
---------- Post added at 06:30 PM ---------- Previous post was at 06:25 PM ----------
Please refer this thread as it might help you.
http://forum.xda-developers.com/mate-8/general/fuss-debrick-restore-mate-8-t3457969
Have a little faith in your Honor
Click to expand...
Click to collapse
I have extract all this img but the flash of cust won't work too so, the dload method can't be launch. Now, I send my phone to the service center yesterday. Wait and See ^^
technoguy09 said:
Did you use Huawei Firmare Finder for your model ?
Click to expand...
Click to collapse
Yes, I Download 2 ROM on it but same problem on both.

Flo.B said:
I have extract all this img but the flash of cust won't work too so, the dload method can't be launch. Now, I send my phone to the service center yesterday. Wait and See ^^
Yes, I Download 2 ROM on it but same problem on both.
Click to expand...
Click to collapse
Leave it for service centre people .they will take care
Sent from my KIW-L22 using Tapatalk

Restore stock B131

Hello,
I have B360 but got some problems :no keyboard, and can't access to developer option ( so i can't enable usb debugging and go on bootloader)
I also can't access TWRP (stuck at message' devices will booting....)
I'm trying to restore stock B131 and follow this https://forum.xda-developers.com/showpost.php?p=70870396&postcount=149
But when it start install, it failed at like 7%
What should i do ?

Tell us more details about what you have done,phone model and what files you used for the rollback. Maybe then we can help you

Sheldd said:
Tell us more details about what you have done,phone model and what files you used for the rollback. Maybe then we can help you
Click to expand...
Click to collapse
Model FRD-L09
I update from B131 to B360, using this method https://forum.xda-developers.com/showpost.php?p=70396400&postcount=547 but my /data was encrypted so I format data
Now I don't have anymore access to twrp idk why. And I have no keyboard, and when I click on developer option to enabling usb debugging, It instantly close the menu.
So now I have no acces to twrp/bootloader and i'm on B360 with no keyboard/develloper option bugged :'(
I want to restore stock B131, and I tried this using dload method, but it fail at 7%
I used this file [https://www.androidfilehost.com/?w=files&flid=129652, I think it's the good file

remi13014 said:
Model FRD-L09
I update from B131 to B360, using this method https://forum.xda-developers.com/showpost.php?p=70396400&postcount=547 but my /data was encrypted so I format data
Now I don't have anymore access to twrp idk why. And I have no keyboard, and when I click on developer option to enabling usb debugging, It instantly close the menu.
So now I have no acces to twrp/bootloader and i'm on B360 with no keyboard/develloper option bugged :'(
I want to restore stock B131, and I tried this using dload method, but it fail at 7%
I used this file [https://www.androidfilehost.com/?w=files&flid=129652, I think it's the good file
Click to expand...
Click to collapse
I think i know what you have done wrong, you didnt flashed the rollback package.
Here you have the rollback package for your device http://download-c.huawei.com/download/downloadCenter?downloadId=92134&version=363841&siteCode=it-h
Here you have the firmware, just to be sure it's the corect one http://download-c.huawei.com/download/downloadCenter?downloadId=92104&version=360397&siteCode=it-h
Now the proces is simple.
First, unzip the rollback package, copy the update.app to dload folder and do the force update (Press and hold Volume UP+Volume Down+Power Button)
Second do the same things but now with the update.app from the B131 firmware zip.
DONT PUT BOTH update.app at once. First the rollback update.app and then the B131 update.app.

Sheldd said:
I think i know what you have done wrong, you didnt flashed the rollback package.
Here you have the rollback package for your device http://download-c.huawei.com/download/downloadCenter?downloadId=92134&version=363841&siteCode=it-h
Here you have the firmware, just to be sure it's the corect one http://download-c.huawei.com/download/downloadCenter?downloadId=92104&version=360397&siteCode=it-h
Now the proces is simple.
First, unzip the rollback package, copy the update.app to dload folder and do the force update (Press and hold Volume UP+Volume Down+Power Button)
Second do the same things but now with the update.app from the B131 firmware zip.
DONT PUT BOTH update.app at once. First the rollback update.app and then the B131 update.app.
Click to expand...
Click to collapse
Oh ok thanks.
So I used rollback update, 100% ok
then use the second update.app but it failled at 8% with this file https://www.androidfilehost.com/?w=files&flid=129652
, I'm downloading your file but I think it's the same file :s

I tried with your file Honor 8_Firmware_FRD-L09_Android 6.0_EMUI 4.1_C432B131_Western Europe, it still failled, not at 8% but at 14% :'(
I notice I got N°Build NRD90M test keys and I should have this FRD-LXXC900B300. (cf .pdf)

remi13014 said:
I tried with your file Honor 8_Firmware_FRD-L09_Android 6.0_EMUI 4.1_C432B131_Western Europe, it still failled, not at 8% but at 14% :'(
I notice I got N°Build NRD90M test keys and I should have this FRD-LXXC900B300. (cf .pdf)
Click to expand...
Click to collapse
I had some strange things at BUILD when i flashed the rollback too, but there wasnt any problem. So when i flashed the B131 everything was fine. Try doing a factory reset on B300 and then flash again the B131. I dont know what to say more, but here is why you have this problems,because you tried to flash B131 over B360....

Yes I did some factory reset and wipe but still fail when I install B131 :/

Do you think there is a solution ?
Or I should go on customer service

remi13014 said:
Do you think there is a solution ?
Or I should go on customer service
Click to expand...
Click to collapse
There is always a solution, don't get panicked. Remember that once you unlocked your phone your warranty got voided. So I don't think Huawei's customer service will give you any advice with your problem.
Try following this:
Can you get into "bootloader"?
If yes, try to extract the needed image files from the B360 update that you used before and follow this guide provided by @eksasol https://forum.xda-developers.com/showpost.php?p=70620803&postcount=9
This video gives you an idea on how to use the Huawei Firmware Extractor Tool: https://www.youtube.com/watch?v=XAtoaL6i_i0
A good note of advice I'll give you my friend. If you get to fix your phone once more, don't tried anything else on it until you are more proficient on how to solve problems by searching and learning from other members' experiences. Use the forum's search tool and you'll find many posts related to your question. I've been helping you through private messages for several issues so far. Don't take me wrong but even though we members like helping others we can't be your private customer care consultants. Hope you can recover your phone's functionality once more.
Regards,

I don't have acces to bootloader, since the developer option is bugged and i can't enabling usb debugging, so i can't reboot on bootloader
]
Dominikrod said:
A good note of advice I'll give you my friend. If you get to fix your phone once more, don't tried anything else on it until you are more proficient on how to solve problems by searching and learning from other members' experiences. Use the forum's search tool and you'll find many posts related to your question. I've been helping you through private messages for several issues so far. Don't take me wrong but even though we members like helping others we can't be your private customer care consultants. Hope you can recover your phone's functionality once more.
,
Click to expand...
Click to collapse
yes, i know thanks and sorry for that

remi13014 said:
I don't have acces to bootloader, since the developer option is bugged and i can't enabling usb debugging, so i can't reboot on bootloader
] yes, i know thanks and sorry for that
Click to expand...
Click to collapse
As far as I know you don't need the debugging option to access the bootloader and use the "fastboot" commands to push the image files.
Just turn off your phone connect it to your computer and use the "Volume down + power on" procedure to get into bootloader.
On the other hand, if for some reason the "OEM unlocking" option was disabled in your phone's /settings/developer options/ then that's gonna be a problem I think, but I'm not a 100%. This might not let you flash the image files through fastboot. Try it and let me know.
---------- Post added at 05:06 PM ---------- Previous post was at 05:03 PM ----------
I know this can be fixed because I've been there before with the same problem as you are.

Dominikrod said:
As far as I know you don't need the debugging option to access the bootloader and use the "fastboot" commands to push the image files.
Just turn off your phone connect it to your computer and use the "Volume down + power on" procedure to get into bootloader.
On the other hand, if for some reason the "OEM unlocking" option was disabled in your phone's /settings/developer options/ then that's gonna be a problem I think, but I'm not a 100%. This might not let you flash the image files through fastboot. Try it and let me know.
---------- Post added at 05:06 PM ---------- Previous post was at 05:03 PM ----------
I know this can be fix because I've been there before with the same problem as you are.
Click to expand...
Click to collapse
I don't think i can access too bootloader
the only way before i did it, it was from commmand " adb reboot bootloader""
and the power+volum do nothing, i only can go on recovery with + and power

remi13014 said:
I don't think i can access too bootloader
the only way before i did it, it was from commmand " adb reboot bootloader""
and the power+volum do nothing, i only can go on recovery with + and power
Click to expand...
Click to collapse
Sorry, I think you misunderstood what I wrote. Let me clarify myself, to get to bootloader you turn off your phone first, then by pressing "volume down/power on" simultaneously until you feel the phone vibrating and see the blue screen. This should get you to the bootloader.
---------- Post added at 05:40 PM ---------- Previous post was at 05:27 PM ----------
Remember to connect your phone first to your computer using the usb/type C cable before attempting to go to the bootloader. I you fail to do this the phone will just reboot normally.

ok it's worked ^^
I will do the Huawei Firmware Extractor Tool tomorrow
I also install twrp since i have acces to bootloader

remi13014 said:
ok it's worked ^^
I will do the Huawei Firmware Extractor Tool tomorrow
I also install twrp since i have acces to bootloader
Click to expand...
Click to collapse
Good. But I don't think flashing TWRP will work but give it a try. I know this from my own experience. What you really need is to flash the recovery.img from the B360 update.zip using fastboot command. That way you'll be able to use the dload method and flash the rollback update.app and after that the update.app from the B131 full zip. That should get you back to stock.

Dominikrod said:
Good. But I don't think flashing TWRP will work but give it a try. I know this from my own experience. What you really need is to flash the recovery.img from the B360 update.zip using fastboot command. That way you'll be able to use the dload method and flash the rollback update.app and after that the update.app from the B131 full zip. That should get you back to stock.
Click to expand...
Click to collapse
So I extracted and flashed via fastboot boot.img, system.img, recovery.img from B360( there are no cust.img in the archive)
After I wipe and reboot. Then install rollback update.app, then update.app B131 but it fail at 25%
But now menu working good and I oculd install a keyboard and do what i want. Maybe i will just stay like this. All is working and i'm on B360. It doesn't matter if I have no root

Sheldd said:
I think i know what you have done wrong, you didnt flashed the rollback package.
Here you have the rollback package for your device http://download-c.huawei.com/download/downloadCenter?downloadId=92134&version=363841&siteCode=it-h
Here you have the firmware, just to be sure it's the corect one http://download-c.huawei.com/download/downloadCenter?downloadId=92104&version=360397&siteCode=it-h
Now the proces is simple.
First, unzip the rollback package, copy the update.app to dload folder and do the force update (Press and hold Volume UP+Volume Down+Power Button)
Second do the same things but now with the update.app from the B131 firmware zip.
DONT PUT BOTH update.app at once. First the rollback update.app and then the B131 update.app.
Click to expand...
Click to collapse
Ive tried this and i'm stuck at 5% of the rollback any suggestions

how to restore my emui

Help with Honor 8 AL10

I have an honor 8 AL10, Chinese version, today I changed the oeminfo to EVA-l09 it was a mistake, I had and I installed TWRP and tried to flash another rom but I cleaned all data including, system, data, completely everything. And now I have a great brick, I have not been able to repair, I have tried in many ways. I need help friends, I would appreciate it. The mobile does not update the firmware by eRecovery, nor by dload, I need help.

I will send you via pm to solve this

maartenw8 said:
I will send you via pm to solve this
Click to expand...
Click to collapse
Friend, I do not have fastboot, ERROR MODE

Help! Error mode frd-al10 help!!
HELP!!!!!

marpermes said:
Friend, I do not have fastboot, ERROR MODE
Click to expand...
Click to collapse
Try to enable fastboot by powering off your device. Plug the USB cable in the PC but not yet in your device. Hold volume down and plug in the USB cable. You should be in fastboot now

maartenw8 said:
Try to enable fastboot by powering off your device. Plug the USB cable in the PC but not yet in your device. Hold volume down and plug in the USB cable. You should be in fastboot now
Click to expand...
Click to collapse
Continue the error, my friend

marpermes said:
Continue the error, my friend
Click to expand...
Click to collapse
Try fastboot devices. Maybe your device is recognized by fastboot

maartenw8 said:
Try fastboot devices. Maybe your device is recognized by fastboot
Click to expand...
Click to collapse
Recognized by fastboot, what else do I do?
Appears in the build:
EVA-L09C432
Note: Made with Huawei MultiTool

marpermes said:
Recognized by fastboot, what else do I do?
Appears in the build:
EVA-L09C432
Note: Made with Huawei MultiTool
Click to expand...
Click to collapse
Flash your recovery image with fastboot. "fastboot flash recovery YOURIMAGE"

maartenw8 said:
Flash your recovery image with fastboot. "fastboot flash recovery YOURIMAGE"
Click to expand...
Click to collapse
Friend, but where do I find the rom for frd-al10? Or do I have to Flash P9 Recovery? Please help me

marpermes said:
Friend, but where do I find the rom for frd-al10? Or do I have to Flash P9 Recovery? Please help me
Click to expand...
Click to collapse
Search it on the internet. Don't flash p9 recovery. You're on honor 8
---------- Post added at 11:51 AM ---------- Previous post was at 11:38 AM ----------
maartenw8 said:
Search it on the internet. Don't flash p9 recovery. You have honor 8
Click to expand...
Click to collapse
Flash this one: https://forum.xda-developers.com/honor-8/development/twrp-t3566563

maartenw8 said:
Search it on the internet. Don't flash p9 recovery. You're on honor 8
---------- Post added at 11:51 AM ---------- Previous post was at 11:38 AM ----------
Flash this one: https://forum.xda-developers.com/honor-8/development/twrp-t3566563
Click to expand...
Click to collapse
Ready friend, please explain to me what else I do. I already have twrp installed.

marpermes said:
Ready friend, please explain to me what else I do. I already have twrp installed.
Click to expand...
Click to collapse
What does the error lose report now?

maartenw8 said:
What does the error lose report now?
Click to expand...
Click to collapse
I need to flash the rom for frd al10, I downloaded thousands of operating systems and the phone does not boot. Done from dload, twrp and in eRecovery appears '' getting info package failed '' and I get nothing. In huawei multi tool I read the build info and appears EVAL09C432, which corresponds to Huawei P9. I downloaded roms for P9 and frd Al10 and the problem continues, the phone does not boot. I need to remove that and have my normal phone

marpermes said:
I need to flash the rom for frd al10, I downloaded thousands of operating systems and the phone does not boot. Done from dload, twrp and in eRecovery appears '' getting info package failed '' and I get nothing. In huawei multi tool I read the build info and appears EVAL09C432, which corresponds to Huawei P9. I downloaded roms for P9 and frd Al10 and the problem continues, the phone does not boot. I need to remove that and have my normal phone
Click to expand...
Click to collapse
Try flashing your AI10 firmware via fastboot. Extract the images in the tool I provided you beforehand

maartenw8 said:
Try flashing your AI10 firmware via fastboot. Extract the images in the tool I provided you beforehand
Click to expand...
Click to collapse
I try to install by dload, it does not work.
I try to install with power, vol + and vol - and it does not work either
'Software install failed incompatible with current version'
I try to recover the system by eRecovery and it appears: 'Getting package info failed'

marpermes said:
I try to install by dload, it does not work.
I try to install with power, vol + and vol - and it does not work either
'Software install failed incompatible with current version'
I try to recover the system by eRecovery and it appears: 'Getting package info failed'
Click to expand...
Click to collapse
Try via fastboot

marpermes said:
I try to install by dload, it does not work.
I try to install with power, vol + and vol - and it does not work either
'Software install failed incompatible with current version'
I try to recover the system by eRecovery and it appears: 'Getting package info failed'
Click to expand...
Click to collapse
Use hw multitool to unbrick

venugopalu007 said:
Use hw multitool to unbrick
Click to expand...
Click to collapse
Your device is booting now...

maartenw8 said:
Try via fastboot
Click to expand...
Click to collapse
Your device is booting now...