Related
OK, heres the deal..
Yesterday I managed to crack the bottom-left corner of my BA screen (damn medkit shifted onto it in my car glovebox ).
As i was checking to see how much of the screen was still responsive (seemed OK, still usable, only the 'New' button and the bottom item of the menu didnt work) the battery died (as in completely, hard reset died)..
So i plug in the power, and start the familiar initial setup. I get to the callibrate screen screen and am unable to continue..
So my question is: Is there any way to bypass the calibrate screen section of the initial setup? Im pretty sure enough of the screen still works for the device to function, if only i could get past this damned calibration screen..
Clearly i cannot bypass it completely, as the screen does need to be calibrated - but is there any way I can recover my BA?
Cheers All
Check out this thread:
http://forum.xda-developers.com/viewtopic.php?t=1910
or this one:
http://forum.xda-developers.com/viewtopic.php?t=6855
Also, if you can still see the image it means that only the digitizer (touch sensitive part) is broken, and not the screen so it shouldn't cost to much to replace.
And remember - search is your friend! :wink:
This might be a bit toooo late, but just in case some one is stuck with a broken screen as dabs and I were.
I received a k-jam (lucky me, it was for free) with a broken touch screen, it was left uncharged for a long time so after charging it, it entered the unwelcomed welcome mode (you know, align, copy, time zone ...) and there were no way of passing this part of initialization.
I had to do some search over the net, and I found a good article here ((Can I use a PDA that has a broken touch screen)) http://www.pocketpcmag.com/blogs/index.php?m=200510 which advised the use of "RemoteCalibration.exe" directly from the pc. This killed the welcome.exe program and I managed to re-use the K-jam again. The only draw back about this way is that I will have to connect the K-jam to a pc every time I hard reset, I hope there is a way to do the same action via mini sd cards.
After that, I installed fakecursor (but I'm looking for a better sw to emulate the touch screen function as this one cancels most hardware buttons on the devise) but at the moment, I'm using all the k-jam's functions.
Hope this would be of help to some one out there
Hi There,
i got a broken display on my HTC Wizard. Very Bad!
I could use the phone, but got the problem with the start screen, wich want to calibrate the touchscreen. Cause of the broken display, I can´t find the right spots. So, is there any way or ROM without calibration? Tried to delete it from my desktop, but I am not "allowed" to do this.
Thanks for any help
PS: is it possible to modify a existing ROM?
long time ago when i had my ipaq 5150 there was a remote control program for the pc that would display the screen and let you use the mouse to touch. I dont know the name, but its a start.
SchmilK said:
long time ago when i had my ipaq 5150 there was a remote control program for the pc that would display the screen and let you use the mouse to touch. I dont know the name, but its a start.
Click to expand...
Click to collapse
I believe kking.kreso cannot get past the welcome screen so he cannot install anything right now.
;P
can you get past the calibration screen or are you stuck at that screen?
if you can get past it but cannot use the device then the program to use is soti pocket controller its free to use for three days
http://www.soti.net/default.asp?Cmd=Products&SubCmd=PCPro
that will allow you to set up the calibration at least.
Edit. If you can setup an active sync connection or even already have one then this will work
PLEASE DO FOLLOW MY ARTICLES!!!!!!!!!
I've explained this ALL at http://www.pocketpcmag.com/blogs/in...that_has_a_broken_touchs&more=1&c=1&tb=1&pb=1
Tried a lot of things now.
Got this error with Remote Screen alignment:An error occured while trying to perform the operation. So no skip...
If I try to delete welcome.ink from Desktop/ActiveSync: Deleting not possible.: You have no rights....
Pen Irazu - I think it needs an installation (can´t read the PIrazu.txt). But I can not Install and start it without the screen.
ThinkOutside Stowaway Travel Mouse ? Can not find it anymore. Probably they don´t sell it anymore. Does another BT-Mouse works?
I am not sure, if I will pass ever this stupid "help"!
Thanks anyway
kking.kreso said:
Does another BT-Mouse works?
Click to expand...
Click to collapse
Yup, with TekSoft's BlueMouse.
I did it! No Calibration- & Welcome-Screen!
OK last my whole weekend, but now i know how to fix it. I used the Trail from SOTI´s Pocket Controller Pro. You need to have it working with ActiveSync. If you can see Your Wizard in your explorer, it will work!
1. Install the Programm on the PC.
2. Try to connect, it says not installet software on PDA and ask to do so: YES.
3. The Welcome-Screen is still there, but don´t care about it. The Softwareinstallation works "behind the scene". just press the left software key twice, wait 15 seconds and then press middle button. now you have it installed!
4. Connect now SOTI´s Pocket Controller Pro with your PDA.
5. You will see now on your Desktop the PDA-screen with the calibrationscreen.
Go on SOTI´s Pocket Controller Pro to "Home" and there is on the right side the DOS-button. Klick it!
6. type: "cd windows", press enter, type "cd startup", press enter, type "del welcome.lnk", press enter.
7. make a software reset.
8. After the reboot, you wont see the calibration screen anymore!
have fun
Kresi
do you have the program installed and can you give it to me installed
i have an x51v and cant install it with the buttons i dont know why but however
say me where i have to put it and then maybe it works
It Worked for me too!
The steps described above worked on a samsung intrepid as well.
only thing i did differently was that i had to reboot my phone after installing the pocket pro software.
Hello
I've got a MDA which has a broken lcd. Its just cracked slightly, but still displays fine. I did a Clear Storage and now the phone has reset and is giving me the "tap here to set up your device" wizard. I need to bypass this and any screen alignment that may come up since the LCD touch feature no longer works. I've done it before when I got the phone, but I cant find the thread nor remember the steps.
Any help is appreciated.
you really can't. i heard theres a way you can flash a rom where the config has already been done, but i don't remember where i saw it
fzzyrn said:
you really can't. i heard theres a way you can flash a rom where the config has already been done, but i don't remember where i saw it
Click to expand...
Click to collapse
create a file on the root of your storage card called welcome.not
TylerC161 said:
I've got a MDA which has a broken lcd. Its just cracked slightly, but still displays fine. I did a Clear Storage and now the phone has reset and is giving me the "tap here to set up your device" wizard. I need to bypass this and any screen alignment that may come up since the LCD touch feature no longer works. I've done it before when I got the phone, but I cant find the thread nor remember the steps.
Any help is appreciated.
Click to expand...
Click to collapse
I believe this should help you.
http://www.freewarepocketpc.net/ppc-download-my-mobiler-v1-2.html
At least I hope it does.
Just create a file named WELCOME.NOT on your storage card and do a hard reset.
HI , I had this problem with all my old crashed PPC ,,, so delete this file and reboot ,,, /Windows/Startup/Welcome.exe
U can use the "Activesynce Explorer to browse the Windows Directory
Enjoy..........
use "Remote screen alignment" tool and bypass your start screen easily. search this tool in forum. you will get it easily..
Regards
welcome.not and http://www.freewarepocketpc.net/ppc-...iler-v1-2.html
THANK YOU SO MUCH kfletch and le_cactus. I'm not sure which of these worked since I did both but the welcome screen FINALLY went away. it took a while. i had to install the Mobiler software and I had problems getting my ActiveSync up but I created the welcome file by going to the desktop of my pc, right click, new , text document, i changed the default name "New Text Document.txt to Welcome.not" then I right clicked to copy it. Next---Once the Microsoft Activesync came up, I clicked on Explore --> My Windows Based Device ---> Storage Card then I selected paste to paste the welcome.not file. After this it gets a little tricky because your device has to sync again to filter the file back down to the phone. This took a while. Then after a few resets, the Mobiler software finally read 'connected', then it gives you a screen shot of your mobile device, i did a soft reset a few MORE times and it worked. It's not as cut and dry as previous posts made it sound. it's a pain in the butt.
My touch screen (T-Mobile Wing) stopped working after I used it in the bathroom while in the bathtub (I don't know what the heck I was thinking), well later that day the screen stopped working and the genius at tech support had me do a hard reset and software upgrade, which did NOT help. (whatever you do, don't call tech support, especially if the white dot beneath the battery is another color---you're screwed!!!)--AFTER tech support messes up your phone they won't bother to help you if they think it's due to water damage! I'm going to see if I can locate the forum regarding reloading the touch screen drivers. I think that may be the problem.
thanks dear I try i350 gSMART and working.
how do you select "YES" when mymobiler tries to install on the phone?
my screen is also broken, and i bypassed the welcome screen, but when i tried to install mymobiler, i cannot let the phone install remote.exe
any help?
this is ur answer
go to this its my room iam build it and not have align screen
http://forum.xda-developers.com/showthread.php?t=546422
Thanks a lot folks from XDA! I had screen broked and this works just fine! Cingular 8125 WM5. tks
ah_hin said:
how do you select "YES" when mymobiler tries to install on the phone?
my screen is also broken, and i bypassed the welcome screen, but when i tried to install mymobiler, i cannot let the phone install remote.exe
any help?
Click to expand...
Click to collapse
Buy a not broken screen
HTC TYTN(Hermes 200)
Hi there i have an HTC TYTN, happens that i'm suposed to have the same problem (maybe broken screen).
The phone was working fine untill today.
I can't bypass the screen alignment; i tryed both ways.
What can i be doing wrong?
Thanks in advance.
Bypassing with "logic"
Hi there;
In my case; i found a way to bypass it.
My screen has a 4mm scratch in the top left of the screen.
so i just pressed the bottom of the cursor (NOT IN THE MIDDLE WHERE IT'S SUPPOSED TO PRESS - "in the top left cursor" - where the scratch is)
after that i could use my phone again.
Also after this try finding the correct registry screen alignment and save it.
It will work properly.
welcome.not works for TyTN II with unresponsive touch screen . Blank micro SD card with just one blank file welcome.not. You can insert the sd card just before you hard reset
It worked in OMNIA II and passed the screen calibration..Thanks a lot guys!!!
Hello all... got kind of a big problem that i at the moment don't have an answer to,..
inastalled advanced configuration tool 3.2 on HTC Polaris, the first crash i had was when I enabled animation for menus... (the start menu turned black and the polaris froze), but when i managed to start the advanced configuration tool i unchecked it and it was ok,...
the MAJOR PROBLEM accured when I set the touch screen sensitivity, because the touch part of the screen is inresponsive,.. meaning it does not work at all,.. tryed very hart pressing but it doesn't do it.. the problem is because i can't reach eg start menu or the lower 2 shortcuts with hard button cursor (the wheel)... gestures work however, so i can call the touch flo cube but am not able to select anything, and sam thing goes for enetering pin,.. so i'm not able to make phone calls at the moment.. did few hard resets, and uninstalled the adv. conf. tool but nothing helped... can anyone tel me where (and how to get there) can i adjust this back to normal, i wanted to do this in the advanced configuration tool 3.2 but the problem is you cant make any changes since the screen doesn't work,.. same with reinstalling the program, i can select to install it on a card but canot "click" on next since the screen doesn't do it and the hard keys "can't go there"
so really really someone help me please...
thnx
Are you sure you hard reset and this problem went away or did you mean soft reset?
Maybe aligning the screen will help reset the pressure? Click the button in the middle of the wheel and the GPS button at the same time, the Windows align screen pops up. See if that helps.
I find it very hard to believe that you hard reset and the touch screen sensitivity is still not there. That can't be right.
Hi,
thanx for the reply,... another problem that accoured afterwards was that my friend held the end button (wich locks the keys, screen) and the phone was additionally locked... and literally nothing (again NOTHING ) helped, spent 5 hours trying to save the situation,.. i did soft reset (so your assumption was right) but when later tryed hard reset it probably wasn't done since the instructions say you do it with holding gps and iExplorer buttons while soft reseting it... this resulted in getting the "hard reset screen" wich says to confirm hard reset with hitting the send button, wich unfortunatelly i wasnt able to find in hard keys, and nothing else but this warning text was on the screen as well.. so in the end it probably ended upo wit soft resetting it, anyways it didn't help,... i decided to reinstall the rom i downloaded on htc official site,... it went thru ok and the phone is , though out of the box at least functional,... but in the end, i must admit that am a little surprised this happened with this tool pack (i actually avoided altering the registers just in order to avoid this kid of situations since i don't really know much about these things)... was expecting it to work (in my case) a bit better, more stable. All i wanted really was to get a bit louder speaker volume when ringing and ability to alter the HTC home toolbar, since i find the weather screen totaly irreliable and never really use it, so i thought I would have sth there that i might really have some use of..
well nevertheless.. the phone is working, that's all that matters at the mom so i can again start finishing my phd wich i am defending in a week
PS. the fact that you can not do practically anything without the touch screen just sucks big time, if i compare it to the mouse on pc,... i saved the situation many times with the keybord .. in 1 word strange
take care
My Mobile
Perhaps you should have tryied out the "My Mobile" aplication that allows you to use your mobile from a PC.
It shows a windows with the mobile screen and you can touch it and use the mobile like if you was touching the REAL mobile...
Late for that solucion, perhaps another with that problem can solve it this way...
Chears
@gastonfama: am not sure this would help, since a friend that has htc diamond has this tool pack on and it work k ok on his phone,.. that's why i predicted that it is going to be stable enough on mnie as well,.. so in my thinking, if the 2 htc that are rather alike had such different "reaction", than an emulation would be even less comparable to mine, thanks though
Had the same problem with Schaps_AdvancedConfig and wrong HKEY_LOCAL_MACHINE\Drivers\TouchPanel\PressureThreshold setting.
XML I used had "200" as advised value (system default is 2908!),
after changing you could hit it with a hammer and nothing.
Managed to set is back to recommended value 9000 using MyMobiler app and all problems gone.
See also HKEY_LOCAL_MACHINE\Drivers\TouchPanel\PressureThreshold
sys default is 18866, I use now 19866 and I'm happy
Check tips&tricks thread
I got the same problem, I wanna to install "My Mobiler" but due to the screen is locked, I can't continue the installation, any help ?
well as far as I see here (forgot how i installed it after previous post) you have an exe here :
http://www.mymobiler.com/downsafe.aspx
so you will install it from the pc anyways, but how will you make the confirm on where to install it (mybe if you put storage card out and there will be only 1 memory option, but you will still have to confirm installation i guess).. i wasnt able to confirm without the screen on polaris,.. maybo on some other phone
double post...mistake
I had that same screen not working problem after tweaking the phone with advanced config 3.3, 3.2, 3.1, only hardware buttons work.
Problem can only be solved by Hard Reset. Version 2.2 I think is the only one that works (not thoroughly tested though)
Hello,
My phone was waterdamged and stop working completly.
I opened the case and tried to dry it.
after 48 hours of trying various stuff, there is blank screen, but:
1. The phone is booting fine, charging led is working.
2. Using Wondershare-Mobilego, i can backup all the content.
3.The touch interface seems to be working fine, i can see the menus via mobilego duplicate screen (can open the sms box or whatsapp and etc.)
4.Incoming messages keep coming...
I`m so frustrated that i`m using the phone blindly or like remote desktop.
Is it software of hardware fault?
THANKS
Tamir245 said:
Hello,
My phone was waterdamged and stop working completly.
I opened the case and tried to dry it.
after 48 hours of trying various stuff, there is blank screen, but:
1. The phone is booting fine, charging led is working.
2. Using Wondershare-Mobilego, i can backup all the content.
3.The touch interface seems to be working fine, i can see the menus via mobilego duplicate screen (can open the sms box or whatsapp and etc.)
4.Incoming messages keep coming...
I`m so frustrated that i`m using the phone blindly or like remote desktop.
Is it software of hardware fault?
THANKS
Click to expand...
Click to collapse
After water damage you can only expect hardware damage. to verify - when turning on the device, do you see anything on the screen? you can also reboot to bootloader (via the key combination or via the command adb reboot bootloader (and to reboot back to android use fastboot reboot).
If the bootloader shows nothing, 100% hardware (although there is really no need to check, probably is). You can try changing screen, but the problem could also be in the socket (but I think if it were the socket the phone would not even boot). Worth a try.
Thanks, but no good...still blank screen - no display.
As i mentioned, the phone is functioning well (as seen at duplicate screen).
When you offering to change screen, you mean the lcd touch digitizer only?
I don`t need to buy the screen itself, right?
(I can`t parse outside links yet from ebay)
Tamir245 said:
Thanks, but no good...still blank screen - no display.
As i mentioned, the phone is functioning well (as seen at duplicate screen).
When you offering to change screen, you mean the lcd touch digitizer only?
I don`t need to buy the screen itself, right?
(I can`t parse outside links yet from ebay)
Click to expand...
Click to collapse
I mean the LCD itself. If touch is working, the problem is the LCD itself, not the digitizer.
You right, it seems that the touch working fine.
You think that a LCD display screen replacement would be the best try? can you paste a link from ebay please?