Hi guys, I recently rooted my galaxy s6 edge. and i flashed it back to the stock rom. But after flashing it back my phone is not fast charging and also not getting connected to the USB port. i replaced the cable and also enabled the usb debugging mode. i did hard reset also but nothing changed. Please help.
i'm having the same issue, except i didnt root it... some say its a hardware problem, like the usb port, and some say its a software problem... its about 1 month now and i can't fix it.
I fixed this problem by raising up a little bit that lil thing from the usb charger on the phone. Now everything works like a charm
Also dial *#0808# and make sure you have selected ap and mtp+adb
when i dial *#0808# pops up a message that says: unable to process request.. do you know why?
Related
Hello everyone.
Once upon a time i came to my TP and tried to activate the screen. nothing happened. Screen dead - only very faint backlight showed up. So i thought, maybe the ROM went bad somehow. So i tried soft reset. No change. I tried Hard-reset (which is not as easy when you dont see a thing). Now i thought, ok, just flash it again. BUT thats when the heavy thing came in. The USB cabel doesnt work. It does charge through the cable, but the PC doesnt recognize it at all. Anyone has an idea how i could get in connection with it? If i cannot bring up a USB connection will the guys at the repair factory be ale to connect somehow? I still have warranty (time-wise).
I will be gratefull for any idea on how to make the USB connection or how to flash without USB connection.
After some trying i found out that Windows somehow reserves USB slots for certain devices and after plugging the cable into different slot i managed to get a Sync and USB connection.
Then i faced the problem with returning "blinded" stock ROM and stock SPL. Thanks to the great guides here i managed to download a Stock ROM and flash it onto the Raphael. Then i faced the problem with putting in the Stock SPL, but it worked once i put the device into bootloader mode with Volume Down + reset.
So now i hope my device is as Stock as i bought it, and i will be sending it in for warranty repair or exchange. I hope its just some minor problem with display.
i rencetly bought the htc touch pro but when i connect trough usb on pc the pc does not reconize. it's not showing nothing on phone i try severel usb's and diferent pc's with diferent operating system. the phone charges but it not recognize. i only can syncronize trouhg bluetooh.
i did all the step's i find in the forum and in the internet. and i'm getting the same results.
Please anyone can help me ???? tnks.
Sory for my english.
Are you running stock or a custom ROM? I haven't had that issue(yet) but I am trying to help troubleshoot.
viBranZeOS-2.0-WWE this is the rom that i'm using. and i try alredy 2 other roms, and its the same.
I honestly have no idea what the issue is nor a fix/work-around. However, what I am attempting to deduce is if you had a stock ROM I wouldn't be of much assistance because I only run the ROM in my sig/signature, which is a custom ROM. Now, I'm not 100% on if your ROM has this option but I know the ROM in my sig has an option to change the behavior of the USB connection, from mass storage to active sync. What I am attempting to figure out is if one of those modes has been enabled and the registry is just not accepting or if the usb port is stuck on only charging. I have no clue on how you would find out as I've never heard of that ROM. By the way, what version of TP do you have, GSM or CDMA and is it a RAPH100, RAPH110 or what ever is showing above the imei behind the battery. You should see a bar code and just above that are four (4) letters followed by three (3) numbers. Let us know what you have and maybe someone else can chime in.
EnergyROM 29018 w/CHT2.0&.sencity this is your rom ??? i can give it a try. how can i see if is GSM or CDMA ???? my phone is RAPH100.
tnks in advance.
p.s i'v had the phone charging for 2 hours and it's only 2 risks. :s
Clarification: It's not my ROM but it is a ROM that I use most often. GSM/CDMA depends on your carrier/service provider. Looks like you may have a GSM device but I'm not a 100%.
Additionally, what happens when you turn off(shut down your phone completely) and charge?
well i'm using vodafone. and the phone is unlock from factory. it was that the guy told me. i am giving a try with that rom. whit the phone shut down and usb turn on the home buton stay's whit the light. i'n the 3 color screen when i conect the usb it's allways saying serial and don't change to usb.
Not exactly sure that is what I am asking. So do this for me: remove the battery, then put it back in and without turning on the device, plug in your phone to a charger(not USB cable) and tell me if you see an LED circle around the center button slowly light up and then disappear.
yes is that what it happens. and it happens this to with the usb plug in. whit the phone on or off.
So let me guess here, does it still take forever to charge from 30% and still get hot when the device is completely off and plugged in. If so, it still seems like it could be a battery issue to me. I don't know how to confirm if it is the device or the battery but I'd start there if you haven't already.
Additionally, if you are getting to the multicolor screen, then connecting the device to your computer and not seeing the change from Serial to USB and you've already tried changing the USB port, USB cable and computer then it is possible that your device's USB port is somehow broken(for the lack of a better word).
"if you are getting to the multicolor screen, then connecting the device to your computer and not seeing the change from Serial to USB and you've already tried changing the USB port, USB cable and computer then it is possible that your device's USB port is somehow broken(for the lack of a better word)."
you are right i go the multicolor screen and not change from serial to usb. but i didn't try in other computers. i will tell you when i try.
Recently we have been getting in stock i997's that are having USB issues connecting to the computer. As always we enable USB debugger and connect to the computer however now the units are going into charge mode a few seconds after connecting to the computer and shutting the device down. Once we disconnect the device from the computer it automatically restarts.
Here is what we have done so far with no luck:
-Enable USB debugging
-Disable USB debugging & enable mass storage
-*#7284# was set to USB=PDA, changed to Modem & back to PDA
-*#9090# Didn't see any relevant options
-Slightly bending the USB port
I don't think it is a hardware issue but a software issue that needs to be configured. Any help would be very much appreciated!!
USB
Get it as stock as you can with software. If the USB still does not connect correctly then it is a hardware issue. There was never a problem in any stock rom with USB connectivity.
Just my thoughts. It may not be the phone but the connection-- Computer, cable, oops,-- or drivers.
I'm facing the same problem !
I too have the same problem very weird tried several time stock have no issue in connection. this issue occur after few days not immediately and no regular pattern so can't say what's going on. right now my phone while put on charge shows charging but when un plug it still have 1% as charge no battery put to charge message shows up, tried with charger, usb to computer.
I also noticed before that charging stops and only come in effect when you pull the battery and plug the cable put the battery it will start the phone automatically and charge start up.
Can't ever put in charge in switch off mode as every time it automatically switch on my phone.
I tried several time these step 1. Go back to stock by heimdall , 2. heimdall kernal flash for red cwm, 3 wipe, format, fix permission 4. flash
couple of days work smoothly then problem reoccurs
Did you try mtp mode like with media player mode
Sent from my SGH-I997 using xda premium
RDomke said:
Get it as stock as you can with software. If the USB still does not connect correctly then it is a hardware issue. There was never a problem in any stock rom with USB connectivity.
Just my thoughts. It may not be the phone but the connection-- Computer, cable, oops,-- or drivers.
Click to expand...
Click to collapse
Thanks RDomke for the reply.
We already flashed UCKD5 with no luck. Would there be anything else we could do? I agree that it may be hardware if stock doesn't work but we have been getting in too many units out of box with this issue. Not saying that it isn't possible to be hardware, just seems like it's something that could be software related.
SOLVED
RDomke said:
Get it as stock as you can with software. If the USB still does not connect correctly then it is a hardware issue. There was never a problem in any stock rom with USB connectivity.
Just my thoughts. It may not be the phone but the connection-- Computer, cable, oops,-- or drivers.
Click to expand...
Click to collapse
RDomke,
Many thanks as we have solved the issue with your advise. The 1st unit we were testing did in fact have a bad usb port. Once properly diagnosed we tested another by flashing it back to stock and then performing a factory reset. Once done issue was solved and worked on many other with same issue.
Guys, I have some problem with my Note II, the MTP/PTP function stopped suddenly like 2 days ago. When I connect to PC, the phone doesn't pop-up let me to choose USB connection mode, and in PC it just showed up as 7 CDC's in device manager, this is weird, I am sure that I have the correct drivers installed. Before that my phone keeps pop-up that dock is connected, but I doesn't own a dock though. So I guess it is USB flex cable is faulty, I replaced it and still having the same results. Charging, USB OTG, ODIN mode works fine though, just I am unable to connect my phone to PC. HDMI out I don't know because I don't have the cable. When I ask the shop they said there probably is something fried on the mainboard IC. Is it true? MTP mode is quite important to me man... Tried other kernel like AGNi and select UMS mode also not working, previously it is working though. My phone is out of warranty, and the Knox warranty also voided. Should I sent to Samsung SC? If no go I might change to OnePlus One.
Now I am on stock ROM also not working. :crying:
did you try updating the drivers
through windows automatic updates?
or did you try with win7 or win8 or linux?
Xp has always troubled me with incorrect or missing drivers
I have a Galaxy S6 edge which I had previously rooted and was running the Renagade's ROM on it. I unrooted it and went back to stock. Anyway, I was going to give it to my son and it stopped fast charging and I am unabel to connect it to a PC. I have tried everything I can think of. Different chargers and cables (I all know work because I have an S7 edge and works fine with it) It' happened after an OTA Update. I have even done a factory reset multiple times. I even had the charger port replaced because Sprint said it was a bad port.
I am wondering, is there a way to root the phone without connecting it to a PC and flash a ROM on it. I think it's a software issue. (Oh and before someone says do I have Fast Charging enabled, yes it's enabled. lol)
I'm on software G925PVPS3CPG1.
Any help would be appreciated.
Try dialing ##DIAG# (##3424#) and making sure it's set to PDA, then click "Qualcom USB Setting" and make sure MTP is selected.
I did try that and it is all set correctly but still get the same result.