Hello,
I have phone H600 H640_77v01.01b01 replica for SGS3 (MT6577),but it is briked,when I connect it at my computer,only what can I see it is MTK USB Port (COM 28) in "Manage" ,no light,nothing else!
When I try to flash it with SP Flash tool I got some error after red line,only what can I do it is format.
What can I do to recognize it like MT65xx preloader? I need to press some buttons when I connect it to my computer?
Sorry for my little english!
are you sure this is an MT6577 based smartphone? how do you managed to brick it? flashed wrong firmware? we need some more inforamtions here. "some error" is something i cannot build onto. make a photo of the back of your device (without the battery) to identify your device. you`ll need to get a proper firmware for your device or it will be dead forever.
edit: found this software, this one MAYBE will work: http://4shared.com/file/IAkoq9Z5/
i didn`t looked into it, but is suggest you have to flash it using SP flash tool.
I tried to install a new rom on Amoi a862w, and installed it, but when I turn it on I got only black-and-white screen, tried to go again, but again the same thing. I have connected a it on a computer via a USB cable, the phone is formatted by himself, now not even that works, when I connect to the computer, PC recognize the phone as "Qualcomm HS-USB QDLoader 9008" qualcomm download mode, so there is no system on it, is there a program that could use to put on a new system, I've tried over the flash tool, but when I want to throw in a scatter file writes me that scatter file is wrong. Please people help me because I love my cell phone. Sorry for my bad English. I hope that someone will understand
A quick search did not come up with much for your particular Device. There was one thread, but it does not have much ( thread link below ) . I would suggest posting your question in Android Q&A, Help & Troubleshooting. Best of luck .
EDIT:
Additionally, you may want to try a fresh Clean flash of the Rom you have. Making sure to verify the MD5 Checksum before flashing the Rom zip file. There is a good guide HERE on how to Flash a Rom.
[Help] Rooting Amoi N820
Hi guys,
I just recently happen to soft brick my micromax a117(mtk 6589t chipset) while using a software to increase the ram. I forgot to turn on the debugging mode. Now i am unable to flash and install stock rom cause the debugging mode was not turned on .
I am able to access the "android system recovery" mode. However, when I try to factory reset the phone I get an error showing "mount/data error".
Can anyone please help me fix my phone? I have used this phone for less than a year.
Please help me I do not have a spare phone either
anup.antony123 said:
Hi guys,
I just recently happen to soft brick my micromax a117(mtk 6589t chipset) while using a software to increase the ram. I forgot to turn on the debugging mode. Now i am unable to flash and install stock rom cause the debugging mode was not turned on .
I am able to access the "android system recovery" mode. However, when I try to factory reset the phone I get an error showing "mount/data error".
Can anyone please help me fix my phone? I have used this phone for less than a year.
Please help me I do not have a spare phone either
Click to expand...
Click to collapse
Try to install stock rom using SP tools. There will not be any problem. I have done it without debugging mode on.
Just one most imp thing is that Always use LATEST SP tools. Best of luck
navtab said:
Try to install stock rom using SP tools. There will not be any problem. I have done it without debugging mode on.
Just one most imp thing is that Always use LATEST SP tools. Best of luck
Click to expand...
Click to collapse
Hi,
I already tried to do this. However, the SP tools software does not seem to detect my phone. Making it unable to install the stock rom. I have tried installing multiple drivers but none of the seemed to have helped.
Please advice what has to be done
Thank you.
anup.antony123 said:
Hi,
I already tried to do this. However, the SP tools software does not seem to detect my phone. Making it unable to install the stock rom. I have tried installing multiple drivers but none of the seemed to have helped.
Please advice what has to be done
Thank you.
Click to expand...
Click to collapse
i think the issue is driver were not installed properly on pc. use moborobo universal driver kit software for pc
Don't panic bro. Driver may not have installed properly. Please reinstall it
anup.antony123 said:
Hi,
I already tried to do this. However, the SP tools software does not seem to detect my phone. Making it unable to install the stock rom. I have tried installing multiple drivers but none of the seemed to have helped.
Please advice what has to be done
Thank you.
Click to expand...
Click to collapse
1. Power off the device and remove the battery(don't connect to pc juz switch off)
2. Open device manager in pc(control panel -> hardware and sound -> device manager)
3. Double click Ports(COM & LPT). It will show some COM ports available
4. Now connect your phone to pc
5. A new device appears in ports tray named something like Mediatek device(not the full name i cant remember now). It will appear for only few seconds. Before it disappears quickly right click on it and click properties
6. In the properties window goto Driver tab and click Update driver
7. A new window pops out, in that select "Browse my computer for driver software"
8. Now browse for the folder u have the a117 drivers and proceed. Windows will install the drivers.
9. Disconnect the phone and restart the pc
10. Open SP Flash Tools(try latest possible version) with adminstrator privilages, select the scatter loading and browse for the file in stock rom folder and click "Download"
11. Connect ur phone and sp tools will detect the device and wait for the process to complete.
Gud luck :good: :good:
a117 bricked
my a117 is stuck on mmx logo...pls help asap...any video tutorial or proper step by step procedure wud be appreciated as ive nvr done flashng thru sp before...thanks ..help anyone asap
My mt6572 smartphone was working fine,but I flashed a ROM of different device EVEN replaced my stock preloader usin SPflashtool.SPflashtool popped up ok.
Now my mobile don't turn on,not go to recovery mode,meta mode,not detected by PC,NO ANY KIND OF SOUND,no change in device manger(i.e no mt65xx preloader...etc),if I install preloader drivers manually it gives error code 10(device cannot start)
Please don't say that "hold volume up+down ,power etc without battery,connect usb and put battery again."
IS my phone dead?but can flashing wrong ROM effect the hardware in someway?
UBAID09 said:
My mt6572 smartphone was working fine,but I flashed a ROM of different device EVEN replaced my stock preloader usin SPflashtool.SPflashtool popped up ok.
Now my mobile don't turn on,not go to recovery mode,meta mode,not detected by PC,NO ANY KIND OF SOUND,no change in device manger(i.e no mt65xx preloader...etc),if I install preloader drivers manually it gives error code 10(device cannot start)
Please don't say that "hold volume up+down ,power etc without battery,connect usb and put battery again."
IS my phone dead?but can flashing wrong ROM effect the hardware in someway?
Click to expand...
Click to collapse
Greetings,
Thank you for using XDA Assist. Unfortunately, it does sound like a hard brick to me. You could ask for more opinions here:
Android Q&A, Help & Troubleshooting
Good luck!
This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc)
THIS IS FOR INFORMATION ONLY.
Q. How Phone gets Bricked?
Ans : Basically, phone get bricked during the installation of Android OS (flashing).
Reason/why it happens
- If flashing is interrupted by low battery or loose cable connection during flashing.
- Using wrong firmware or a custom ROM (unstable) to flash your phone.
Result:
* Phone will not boot even after holding the power key and it will not accept charging. (Hard Brick / Dead Brick)
* Boot-Loop
* Restart loop
* No Recovery (In this situation, Hard Reset will not work)
Q. - Why Phone becomes dead (MTK Android Phone) ?
Ans : While installing Custom ROM or Stock firmware (unstable), Preloader (.bin) file becomes corrupted.
PRELOADER - It is the file in MTK android phone which helps to boot the phone.
Tools & Software Required:
SP Flash tool
Android Stock ROM
MTK USB Driver
PC / Laptop
Dead MTK Phone
USB cable.
NOTE: SP Flash tool has 3 Dropdown, Its meaning & How to use:
MOTA SIU : while choosing this function before clicking on Download, only boot, recovery and Android will be updated.
Format All + Download : while choosing this function before clicking on Download, it first erases the old Firmware then install new firmware. (Recommended when MTK phone stuck at logo & hard reset fails)
Firmware Upgrade: while choosing this function before clicking on Download, its update the Android version. (Recommended when installing a higher or lower version of Android manually)
Steps to Fix/Unbrick Dead Android (MTK) Phone
1- Install MTK driver.
2- Download the tool.
3- Unzip it and double click on Flash_tool.exe.
4- It will launch the tool.
5- Download Android stock ROM, unzip it.
6- Click on Scatter-Loading and assign the path of file (Select Firmware i.e. {.txt extension}).
7- Click on Download.
8- Switch off Mobile and connect it to PC using USB cable by pressing Volume down as boot key.
9- Flashing starts and when completed, Download OK will appear.
Also check Here for more Understanding, Special Thanks to @yuweng
Please let me know if anything is wrong here, so that I can make correction and help other member for better understanding.
Also hit THANKS button if you find this as useful info.
If you found this post helpful then don’t forget to share this post with other Android users so that they could get their dead phones working in few easy steps without paying few dollars on it.
Reserved
Nice Guide, Can you please list MTK devices ????
421rahman said:
Nice Guide, Can you please list MTK devices ????
Click to expand...
Click to collapse
OK, Will be adding attachments later, Thanks
Salman
--
Thanks @Salman Al-Badgail for this use full info.
Deena Khanam said:
Thanks @Salman Al-Badgail for this use full info.
Click to expand...
Click to collapse
welcome & Thanks
@jamsubzero check this guide
@jamsubzero I saw your post and thread regarding Dead Bricked
Hey guys.
I own a lenovo A328. For the past couple of months my phone, gets poping up "com.google.etc.etc has stopped".
I tried doing a factory reset, but no luck. Then I learn that I can flash it using SPflash tool with the stock firmware.
And luckily, I did it, my phone back to normal. But then, a few couple of weeks, it started to pop up the same error messages again until I can't do anything on my phone, and unitl it boot loops. So, I reflash again with the same firmware (stock).. and it works again. And same thing keeps repeating and repeating;
until I thought I can try to change the options in sp flash tool..
Instead of "Download only", I choose, "Firmware upgrade".... the flashing finished successfully.
BUT when I press the power button to turn it on, nothing happens, and when I charge it, I cant see the charging screen (or it's not actually charging). I'm sure that it is charging before the flashing, and the power button is working.
When I connect it to the computer, i hear a "connected" sound, then "disconnected", and repeating.
i also tried to reflash it, both the "DL only" and "Firmware upgrade", even the "Format all + ...."
and it flashed successfully (meaning, computer still recognized it), but still not turning on.
Please help me. please.
Click to expand...
Click to collapse
NEVER DOWNLOAD ROM NOT MEANT FOR YOUR PHONE. IT WILL BRICK IT !
What you did is you flashed wrong firmware to your device and the result you in Dead Brick, However there is still solution for your problem. Please Please Please do a proper search first and download correct firmware and other necessary files for your device. Please check firmware number ok.
You can Flash it again but you need to open phone and try, Check here for better understanding.
GUIDE : HERE. Or else please go to any mobile shop and ask them to flash. Dont tell the original reason that you tried to flash or etc. Tell them that it stop suddenly and for now I am unable to access it. They charge you about 5-15 USD based on your country, for me they had charged 10U$D me for lenovo A3500-HV dead flashing. Hope this help you.
i got no scatter file in stock rom pls help!
Aller retour si flash tool
Hard bricked Lenovo a7000
**Hi I got problem on yesterday I was install ing new Rom but suddenly my Lenovo a7000 hard brick
It is not responding any point .even charging .and charging light also .it's dead
But it when I connet to my pc it's connecting sound conning from pc ....My phone is dead plaease help
Salman Al-Badgail said:
This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc)
THIS IS FOR INFORMATION ONLY.
Q. How Phone gets Bricked?
Ans : Basically, phone get bricked during the installation of Android OS (flashing).
Reason/why it happens
- If flashing is interrupted by low battery or loose cable connection during flashing.
- Using wrong firmware or a custom ROM (unstable) to flash your phone.
Result:
* Phone will not boot even after holding the power key and it will not accept charging. (Hard Brick / Dead Brick)
* Boot-Loop
* Restart loop
* No Recovery (In this situation, Hard Reset will not work)
Q. - Why Phone becomes dead (MTK Android Phone) ?
Ans : While installing Custom ROM or Stock firmware (unstable), Preloader (.bin) file becomes corrupted.
PRELOADER - It is the file in MTK android phone which helps to boot the phone.
Tools & Software Required:
SP Flash tool
Android Stock ROM
MTK USB Driver
PC / Laptop
Dead MTK Phone
USB cable.
NOTE: SP Flash tool has 3 Dropdown, Its meaning & How to use:
MOTA SIU : while choosing this function before clicking on Download, only boot, recovery and Android will be updated.
Format All + Download : while choosing this function before clicking on Download, it first erases the old Firmware then install new firmware. (Recommended when MTK phone stuck at logo & hard reset fails)
Firmware Upgrade: while choosing this function before clicking on Download, its update the Android version. (Recommended when installing a higher or lower version of Android manually)
Steps to Fix/Unbrick Dead Android (MTK) Phone
1- Install MTK driver.
2- Download the tool.
3- Unzip it and double click on Flash_tool.exe.
4- It will launch the tool.
5- Download Android stock ROM, unzip it.
6- Click on Scatter-Loading and assign the path of file (Select Firmware i.e. {.txt extension}).
7- Click on Download.
8- Switch off Mobile and connect it to PC using USB cable by pressing Volume down as boot key.
9- Flashing starts and when completed, Download OK will appear.
Also check Here for more Understanding, Special Thanks [email protected]
Please let me know if anything is wrong here, so that I can make correction and help other member for better understanding.
Also hit THANKS button if you find this as useful info.
If you found this post helpful then don’t forget to share this post with other Android users so that they could get their dead phones working in few easy steps without paying few dollars on it.
Click to expand...
Click to collapse
S
Sir please help me out
I have Micromax a120 device. Few days back it got bricked it stuck on bootloop and not working even after factory reset moreover my pc is not recognizing mobile and display message as device descriptor request failed. I have installed all drivers
---------- Post added at 07:47 PM ---------- Previous post was at 07:47 PM ----------
Salman Al-Badgail said:
Reserved
Click to expand...
Click to collapse
Sir please help me out
I have Micromax a120 device. Few days back it got bricked it stuck on bootloop and not working even after factory reset moreover my pc is not recognizing mobile and display message as device descriptor request failed. I have installed all drivers
im having mt8127 mtk device it is not flashing iam having corrupted preloader i tried to flash the preloader it is not flashing , can any body knows to fix it??
How can a phone that's bricked be switched off? Am a bit confused.
Salman Al-Badgail said:
This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc)
THIS IS FOR INFORMATION ONLY.
Q. How Phone gets Bricked?
Ans : Basically, phone get bricked during the installation of Android OS (flashing).
Reason/why it happens
- If flashing is interrupted by low battery or loose cable connection during flashing.
- Using wrong firmware or a custom ROM (unstable) to flash your phone.
Result:
* Phone will not boot even after holding the power key and it will not accept charging. (Hard Brick / Dead Brick)
* Boot-Loop
* Restart loop
* No Recovery (In this situation, Hard Reset will not work)
Q. - Why Phone becomes dead (MTK Android Phone) ?
Ans : While installing Custom ROM or Stock firmware (unstable), Preloader (.bin) file becomes corrupted.
PRELOADER - It is the file in MTK android phone which helps to boot the phone.
Tools & Software Required:
SP Flash tool
Android Stock ROM
MTK USB Driver
PC / Laptop
Dead MTK Phone
USB cable.
NOTE: SP Flash tool has 3 Dropdown, Its meaning & How to use:
MOTA SIU : while choosing this function before clicking on Download, only boot, recovery and Android will be updated.
Format All + Download : while choosing this function before clicking on Download, it first erases the old Firmware then install new firmware. (Recommended when MTK phone stuck at logo & hard reset fails)
Firmware Upgrade: while choosing this function before clicking on Download, its update the Android version. (Recommended when installing a higher or lower version of Android manually)
Steps to Fix/Unbrick Dead Android (MTK) Phone
1- Install MTK driver.
2- Download the tool.
3- Unzip it and double click on Flash_tool.exe.
4- It will launch the tool.
5- Download Android stock ROM, unzip it.
6- Click on Scatter-Loading and assign the path of file (Select Firmware i.e. {.txt extension}).
7- Click on Download.
8- Switch off Mobile and connect it to PC using USB cable by pressing Volume down as boot key.
9- Flashing starts and when completed, Download OK will appear.
Also check Here for more Understanding, Special Thanks to @yuweng
Please let me know if anything is wrong here, so that I can make correction and help other member for better understanding.
Also hit THANKS button if you find this as useful info.
If you found this post helpful then don’t forget to share this post with other Android users so that they could get their dead phones working in few easy steps without paying few dollars on it.
Click to expand...
Click to collapse
i am trying to flash vivo s7 and the cable shake and since then the phone is dead, have flashed it several time, it complete but it refuse to on
I need help please
Basically I was flashing updates for my CUBOT Nova and everything was going fine and I tried out this custom recovery which wouldn't mount any partition so it didn't really suit me. And I did this a dozen of times with other recoveries and if anything happened I had the firmware in SP tools ready to be flashed and if I could save going to it I just used the fastboot to flash it, and so I decided to completly stop and just put my phone back to normal and because I done it before I formatted the whole flash, (and FYI every 2 times I plugged in the phone powered off my computer always searched for drivers in the windows update but it failed and so everything still worked) but after I formatted it and plugged it out and in to download the firmware, my computer successfully installed the drivers and at this moment I was like shoot so I tried to download and it didnt recognise my phone and so I uninstalled the driver my computer installed and see if it worked and it kept installing it again, so I decided to uninstall every mtk driver I had and rebooted, when I installed every single driver again it tried to download drivers from the windows update but it failed and on the sp flash tools it goes to 100% on the Downloading DA (so the red bar) and stays like that for a while and I get notifications that I have a unrecognisable usb device and after a while it gives me randomly 2 errors 0xC0050005 and 0XC0060001 and I know someone is going to tell me I dont have the right firmware or that it's not the right ones but it isn't I got from the official Cubot website and I got an early versions from firmwarefiles I think and none of them work, now I just have a phone without anything on it and I cant flash anything on it until I just hope someone would walk me through what to do I would appreciate so much I'm sorry I wrote so much as I had to explain in max detail as I could what happened!
netcrafy said:
How can a phone that's bricked be switched off? Am a bit confused.
Click to expand...
Click to collapse
i wanted to say the same thing, also i tried enter EDL for 2 days DD (helio G80) LMFAO
Hi there
I would like to know if you can help me in repairing my device.
So i wanted to do an upgrade on the tablet and i messed it up.
I was on CMW recovery at first and then i did a format on cache system and data. but when i wanted to flash the rom CM14.1 it fail and the devices restarted.
the screen goes on but i can see faint lines on the screen.
I did make a back up of the rom and tried to flash it back but it didnt work.
I used all the roms and it still didnt work. I tried many SP flash tool and formating and still not working. every single rom has been flash and all are green but the phone does not want to boot. i have youtube and followed the instructions and every single step i can think of but u have a gut feeling i am mssing something.
I cannot write SN on the fone as it will not work. i have uninstalled all the drivers re-install all the drivers did all the instruction that you have provided but still it will work.
the tablet does still detect on the PC and it does work. so basically it is in a bootloop but its not powering up. Some suggested using MRT TOOLS or MIRACLES but i have a problem with that as it always have a virus attached it to and when i download it the pc removes it. so i dont know where i can get a good crack tool.
i really need your help if you can.
Hello Guys
i closed SP tool while flashing
my phone : infinix hot 10s
i cant power on it and cant join fastboot and cant join bootloader
When i connect phone by orginial usb
computer said (USB not recoginzed)
i installed all drivers but now phone is dead and he was rooted so i cant going to warranty
how i fix it?