Hey XDA I have decided to root my yuphoria(YU5010A) and start exploring it's capabilities however I do not know how to use adb nor can I get my hands on a pc right now. That means I have to gain root access(already done) and install a recovery all from my phone itself. I did try to do it via terminal emulator but I hard bricked my yuphoria and had to get it repaired and I can't afford to lose my phone again so please tell me a method that's already tried and tested.
Regards Andbug
P.S. You are dealing with a noob so explain in detail.
u cannot flash recovery without pc! on yuphoria!!
reboot to fastboot mode and then connect ur phone to pc/lappy! type
fastboot -i 0x2A96 flash recovery twrp.img
Click to expand...
Click to collapse
u need adb and fastboot package As Usual
after flashing dont reboot remove the cable and battery!
after 20sec insert the battery and hold power and vol down button together when the phone shows YU logo leave the power button and start pressing vol down button continuously untill you see TWRP logo! after that it will ask you to allow Modifications to system! ALLOW IT and then down! you have twrp!
Just download any recovery.img from xda and flash it using flashify ..tried it on two yuphoria.works perfectly...
Root yu5010a with King root 1st
2nd Install flashify
3rd flash TWRP recovery manually with flashify
Rooting Guide for Doogee Y6-
So waiting time IS Now Finished , twrp is here,
Basic spec-
Ram - 2GB/4GB
Rom- 16GB/64GB
Camera- BACK- 13MP
FRONT- 8MP
Display- 5.5 INCH
OS -MARSHMALLOW
SoC -Mediatek MT6750
Hit Thanks if This Helpful For you:good:
Full Review Checkout HERE
Disclaimer
Code:
your Device At Least 50-60% Charge During Process
warranty Is now Void, Developers and We are Not Responsible For any Damage,
Backup your Personal Data and apps Before Doing anything
take a Nandroid Backup if possible
twrp Installation-
in Short-
Download twrp Sp Flash tools from Bellow Link
Install All Drivers On PC and Run SP tools
Load Scatter File and Check Recovery only
under recovery Section Load Downloaded twrp.img File
Then Click on Download, Connect your Phone to PC [make Sure Phone IS turned off]
Done,
Fastboot Guide-
Bootloader Must be Unlocked,
Code:
Code:
fastboot flash recovery recovery name.img
Rooting Guide-
Download Supersu.zip from Bellow and put into Root Of Sd Card
Boot Device into twrp [use command adb reboot bootloader] or hold power and volume up key on switch of mod
Allow Modification
make a nandroid backup
Click install Zip from sd crad
Locate Downloaded Supersu.zip file and Swipe to install
after Success go back and reboot system now
Done,
Downloads-
mod edit - blog links removed
Phone for stock on bootloop
Phone got stock on bootloop
Please, what can I do,my Doogee y6 could not boot properly again after flashing the above recovery image using sp flash tool.The device can boot into twrp recovery but can't boot back into the. If I flash I new custom ROM Will it be successful as when I Intend to restore in to factory setting, I got ' failed to Mount ' /nvcfg' in valid argument and then done afterwards. Kindly advice me on what to do please. Thank you.
TWRP language
I have question , i flushed twrp from uplink and now my twrp is not in english it is blody chinees language as it is not touch version of twrp....
any solution for this stuff... is it posible to flash maybe some other recovery so it gets english atleast ???
garabadz said:
I have question , i flushed twrp from uplink and now my twrp is not in english it is blody chinees language as it is not touch version of twrp....
any solution for this stuff... is it posible to flash maybe some other recovery so it gets english atleast ???
Click to expand...
Click to collapse
flash this one:
https://forum.xda-developers.com/showpost.php?p=69800037&postcount=3
it's the newest TWRP recovery for Y6 around
I guess you'll be ok
You don't "need" to root
...
chillo71 said:
flash this one:
https://forum.xda-developers.com/showpost.php?p=69800037&postcount=3
it's the newest TWRP recovery for Y6 around
I guess you'll be ok
You don't "need" to root
Click to expand...
Click to collapse
thx dude , but still only chinese 8 lines in old school look maybe i am not doing it well.. i do flash it all good with sptools
how do you enter to twrp?
garabadz said:
thx dude , but still only chinese 8 lines in old school look maybe i am not doing it well.. i do flash it all good with sptools
how do you enter to twrp?
Click to expand...
Click to collapse
oh now I got it, i think you go in the boot menu, all mediateks have that in Chinese
To get into recovery you must press up volume and then hold it along with pressing the power button,
Y6 after a few seconds turn;s on and you then have to chose which mode to go. Up volume to change selection and down volume to select, recovery mode obviously
chillo71 said:
oh now I got it, i think you go in the boot menu, all mediateks have that in Chinese
To get into recovery you must press up volume and then hold it along with pressing the power button,
Y6 after a few seconds turn;s on and you then have to chose which mode to go. Up volume to change selection and down volume to select, recovery mode obviously
Click to expand...
Click to collapse
after doing that i have =killed= android lieing on screen with red triangle.... under it it says =No command=
---------- Post added at 05:28 PM ---------- Previous post was at 04:58 PM ----------
So for new guys in this i skipped very important step when flashed twrp:
Do not run system , but to bootloader first , accept modifications and whoala...
thx @chillo for responding quickly
BTW The dying android means no custom recovery is installed for Y6 , no fastboot command whatsoever
And yes, Y6 and most new android phones from Marshmallow and newer *(edit: ) stock ROMs, don't like to mess with their system partition, one should select system as read-only
Glad you made it through and learned a bit of it
Bootloop
It appears I've soft-bricked my Y6.
I've installed TWRP 3.03 as above and can boot into it but when I try to do a normal reboot I'm stuck in a boot loop.
How do I get to this stage - "Do not run system , but to bootloader first , accept modifications and whoala..." Is that when you first run TWRP?
In the Mount section of TWRP "System" is not ticked but the button "Mount as readonly" is.
If I select Fastboot it hangs. Normal boot hangs. Boot into Recovery is fine.
Any suggestions?
Thanks in advance
Y6 Max:*install recovery with fastboot in Ubuntu Linux
Hello,
thank you for this very useful thread. Just want to add some information on installing the recovery image on the Doogee Y6 Max via fastboot in Ubuntu Linux
I've followed this instructions with some minor (but important)*changes.
First useful information:*to enter in the fastboot mode of the Y6 max do the follow:
- power off your phone
- push togheter Volume up and Power button
now you will see a menu with three options. Move the arrow with Volume up and select "fastboot". Then press Volume down.
You are now in fastboot mode.
Connect your phone via USB to the computer.
Open a terminal and:
- unlock OEM as described in the tutorial linked above.
- install your recovery.img as described in the tutorial linked above
- re-lock the OEM with this command:
Code:
sudo fastboot oem lock
otherwise your phone won't boot.
Then power off your phone and enter in the menu described above pressing toghether Volume up and Power.
Now select "Recovery" and you are done.
Hi! I did everything like in the tutorial but phone is stuck in bootloop after flashing supersu from sd card. Any advices?
I tried 3.0.3 twrp and newest supersu. Phone turned on but there is not root, also there were no errors during instalation.
Hello Guys
this is my first threads
my english is not good so if you have any questions pls ask in hindi if possible
here i present TWRP RECOVERY FOR MICROMAX INFINITY PRO HS3
STEPS TO FLASH
1- UNLOCK BOOT LOADER
POWER OFF THE PHONE
BATTERY AT LEAST 60%
PRESS AND HOLD POWER KEY AND VOLUME UP
IT ASK YOU ---VOLUME UP-RECOVERY
VOLUME DOWN-FASTBOOT
PRESS VOLUME DOWN AND ITS BOOT INTO FASTBOOT MODE THEN
OPEN ADB AND FASTBOOT FOLDER
ON KEYBOARD PRESS SHIFT AND MOUSE RIGHT CLICK TOGETHER
NOW GO TO OPEN COMMAND WINDOW HERE OPTION
fastboot flashing unlock
or
fastboot oem unlock-go{UNLOCKING BOOTLOADER YOU LOST YOUR HOLE DATA SO FIRST BACKUP YOUR DATA}
2- AFTER UNLOCK ITS TAKE 5-10 MIN TO BOOT {ALERT----XDA AND IM NOT RESPONCIBLE FOR ANY KIND OF DAMAGE YOUR DEVICE SO BE CARE AND BACKUP YOUR DATA}
3-FLASH RECOVERY
fastboot flash recovery recovery.img
4-THEN REBOOT
fastboot reboot
*******WHEN YOU FLASH RECOVERY AND REBOOT WITH CMD {fastboot reboot} ENTER THEN PRESS VOLUME TO GO TWRP AND IN TWRP PRESS REBOOT***********
DOWNLOAD LINK
FASTBOOT FOLDER
[url]http://www.mediafire.com/file/gdd94yv78wen99m/fastboot_folder.zip[/URL]
HS3 RECOVERY
http://www.mediafire.com/file/bfx3cu8un6h9fkl/hs3recovery.img
SUPER SU
http://www.mediafire.com/file/n8uw77pm0v4ru8x/SuperSU-v2.82-201705271822.zip
SUPER SU FLASHING
COPY SUPER SU ZIP IN YOUR INTERNAL STORAGE
SWITCH OFF HS3 AND REBOOT IN RECOVERY WITH VOLUME UP
TAP INSTALL
AND ISNTALL SUPER SU
:victory::victory::victory:ROOT:victory::victory:
vedio link
MOD Edit -Links Removed
recovery not working...could you mail at [email protected]
i want to install oreo updates in micromax infinity but i didn't get rom
can i install rom of anyother android in my phone
please reply me ........
neeraj sharma.... said:
i want to install oreo updates in micromax infinity but i didn't get rom
can i install rom of anyother android in my phone
please reply me ........
Click to expand...
Click to collapse
sorry for late reply
dont try anyother rom untill it ported for this device
Thanks
Thanks
Will this work on any phone?
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
RZaR2001 said:
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
Click to expand...
Click to collapse
Who is better in Red Magic 3/3S
I mean Android = 9/10/11 ?
lilo_ind said:
Who is better in Red Magic 3/3S
I mean Android = 9/10/11 ?
Click to expand...
Click to collapse
Look i use RM3S software but i have RM3 .. i feel that RM3S software smooth more than RM3 software .. look i see u stay on A10 till they fix all bugs in A11 .. its my point + Pubg not working in A11 for RM3/3S so if u playing on it don't use now A11
Edit: pubg worked u can download it from Here
I had problem about less charger mA on 3 charger and cables so strange on my red magic 3s, so yesterday i did buy another cable and same thing less mA like 100 should be 3000 , so i did use one charger adapter rampow for try , when i did put charger less again but the screen get blocked and reboot , when it restarted i did see that if i put to charger again also with orginal charger and cable will block screen and reboot so i did try to reset and install Europe & Asia: V212 , when did get 100% will show that " Device is corrupt. It can't be trusted and will not boot " ,this happen if you put one not original cable or charger i did discovery ,now the problem is if i put the cable on laptop for flash install roms windows will not detected the new hardware of red magic so how can i fix that now
cacaocaca said:
I had problem about less charger mA on 3 charger and cables so strange on my red magic 3s, so yesterday i did buy another cable and same thing less mA like 100 should be 3000 , so i did use one charger adapter rampow for try , when i did put charger less again but the screen get blocked and reboot , when it restarted i did see that if i put to charger again also with orginal charger and cable will block screen and reboot so i did try to reset and install Europe & Asia: V212 , when did get 100% will show that " Device is corrupt. It can't be trusted and will not boot " ,this happen if you put one not original cable or charger i did discovery ,now the problem is if i put the cable on laptop for flash install roms windows will not detected the new hardware of red magic so how can i fix that now
Click to expand...
Click to collapse
U tried the tool unbrick?
i can t do that because windows not recognized the phone , so i should get that before all but i did see some solution maybe and afther can i do all maybe
1. https://forum.xda-developers.com/t/q-bricked-and-not-recognized-by-usb.2280393/post-41531497
2. https://forum.xda-developers.com/t/...device-in-download-mode.1486234/post-22454863
And now maybe i did understand because have less charger also with the new cable maybe
cacaocaca said:
i can t do that because windows not recognized the phone , so i should get that before all but i did see some solution maybe and afther can i do all maybe
1. https://forum.xda-developers.com/t/q-bricked-and-not-recognized-by-usb.2280393/post-41531497
2. https://forum.xda-developers.com/t/...device-in-download-mode.1486234/post-22454863
And now maybe i did understand because have less charger also with the new cable maybe
Click to expand...
Click to collapse
Come pm
RZaR2001 said:
Come pm
Click to expand...
Click to collapse
Thankyou So much RZaR2001 i am glad to say that i successfully unbricked my NUBIA REDMAGIC 3 love you bro❤ No homo
m device is not recognized in my pc i also tried using different laptops so i cant go any more from step 2....and i dint even enable usb debugging is there any way i can enable it from hardbrick mode(currupted stage)
help me please.....
RZaR2001 said:
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
Click to expand...
Click to collapse
This man is sooooo Goooood Thankyou soomuch For helping me and other people out there. This man will give it his time to help and fix my iisue he's actually handsome tho. So i recommend this guy if you want some solution for your problem just direct him. This man is sooooo kind it will make your day much happier hahaha
RZaR2001 said:
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
Click to expand...
Click to collapse
after flash v3.30 device logo restart only
[email protected] -help me bro
RZaR2001 said:
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
Click to expand...
Click to collapse
this man is really awsome for red magic device. now im on v5.11 and using gapps. thnx again
RZaR2001 said:
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
Click to expand...
Click to collapse
Hi
I habe redmagic 3 stuck at device corrupted
I have tried almost every guide i could
Its still same
I tried your way and now it keeos booting back to fastboot
Even if i choose reboot to recovery or reboot to system after i use twrp tool
Any suggestions?
hafizrehman1992 said:
Hi
I habe redmagic 3 stuck at device corrupted
I have tried almost every guide i could
Its still same
I tried your way and now it keeos booting back to fastboot
Even if i choose reboot to recovery or reboot to system after i use twrp tool
Any suggestions?
Click to expand...
Click to collapse
Pm me
RZaR2001 said:
Before starting you need to :
1- download unbirck tool (RM3, RM3S);
2- download TWRP for A11 (for both of them)
3-download minimal adb and fastboot tool ADB
4- Buy OTG Link
The Steps1- You should install the ADB
2- Go to fastboot mode then to Boot to edload (by using volume down) then press power the screen will be black screen
3- Open the unbirck tool and follow the steps which the developer put in his note
4- if the phone didn't open and still giving (device is corrupt) go to again to fastboot mode then open the TWRP tool (its in cn language so may be weird for you) and will explain the steps in pics
5- when it finishes go down in fastboot mode to reach to recovery mode press on power it will take u to TWRP (may u found it in cn language so follow that video to make it in eng)
6- Plug ur flash drive in ur pc and put the rom on it RM3S , RM3
7- Connect ur phone with that flash drive then in TWRP [ Mount > Select Storage > USB-CTG ] then go back and join [Install > the rom which u downloaded] after that restart the phone
Note : 1- While installing TWRP you should be in fastboot mode only, don't go to boot edload ... Sec pic u press on fasboot [may at first u get failed after first pic open the tool again and try again]
2- You will need ADB when u open the bootloader
If there is anything DM me
Click to expand...
Click to collapse
OMG guys
this guy in an angel
within sometime of me posting here for help
he Contacted me through pm
and then we started conversation through whatsapp
he took details of how i got myself stuck
and then through anydesk
downloaded some files and viola
my device is running again
on cn version 5.11 android 11
rooted and with gapps installed
i can't thank you enough brother
god bless you
please guys
give a like to this post
and applaud for his generosity that when i offered to pay him he said he is gona do it for free
Thanks a lot
i wud be forever your thankful
lotz of love n prayer from me❤♥♥♥♥♥♥♥
hafizrehman1992 said:
OMG guys
this guy in an angel
within sometime of me posting here for help
he Contacted me through pm
and then we started conversation through whatsapp
he took details of how i got myself stuck
and then through anydesk
downloaded some files and viola
my device is running again
on cn version 5.11 android 11
rooted and with gapps installed
i can't thank you enough brother
god bless you
please guys
give a like to this post
and applaud for his generosity that when i offered to pay him he said he is gona do it for free
Thanks a lot
i wud be forever your thankful
lotz of love n prayer from me❤♥♥♥♥♥♥♥
Click to expand...
Click to collapse
i want to do the exact same solution but i have bricked my rm3 with a downgrade. now my best problema is that pc not recognized the Phone on fastboot. i'm demoralized...
fedezio said:
i want to do the exact same solution but i have bricked my rm3 with a downgrade. now my best problema is that pc not recognized the Phone on fastboot. i'm demoralized...
Click to expand...
Click to collapse
I also had that issue and i fixed it recently,
Just go to a mobile shop tell them to try to unlock bootloader step while connected to a box like miracle, ultimate where any of red magic series phone available.
After that the result got failed but phone starting recognizing in fastboot mode.
Thnx me later.
Thank you for your enthusiastic help. My phone came back to life
Bro around 15-20 days back I was on global rom, as it was not receiving any update lately thought to install cn android 11 rom. After installing the rom I was unable to find any twrp for it so, I downgraded it to android 10 cn rom, but my phone got bricked. I thought there might be some issue with recovery so I did a fresh install following:
Using cn android 11 rom
Using brioli
Extracted the sdat2img.py system.transfer.list system.new.dat system.img
fastboot oem nubia_unlock NUBIA_NX629J
Fastboot erase boot
Fastboot erase recovery
Fastboot erase system
Fastboot erase userdata
Fastboot erase cache
Fastboot erase data
fastboot erase system
fastboot erase modem
fastboot erase dsp
fastboot erase vbmeta
fastboot erase dtbo
fastboot flash parameter parameter.img
fastboot reboot bootloader
fastboot oem nubia_unlock NUBIA_NX629J
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash splash splash.img
fastboot flash modem NON-HLOS.bin
fastboot flash dtbo dtbo.img
fastboot flash dsp dspso.bin
fastboot flash vbmeta vbmeta.img
fastboot flash -S 100M system system.img
fastboot reboot
It showed device corrupt again
I tried unbrick tool and the twrp you uploaded.
But after installing the twrp, when I try to reboot to recovery, it reboots in fastboot again.
I have tried at least 10-11 times with the above process but no luck.
Please help me out bro this is my only phone and we don't have a service center here.
Best regards,
Dibyank
Dibyank said:
Bro around 15-20 days back I was on global rom, as it was not receiving any update lately thought to install cn android 11 rom. After installing the rom I was unable to find any twrp for it so, I downgraded it to android 10 cn rom, but my phone got bricked. I thought there might be some issue with recovery so I did a fresh install following:
Using cn android 11 rom
Using brioli
Extracted the sdat2img.py system.transfer.list system.new.dat system.img
fastboot oem nubia_unlock NUBIA_NX629J
Fastboot erase boot
Fastboot erase recovery
Fastboot erase system
Fastboot erase userdata
Fastboot erase cache
Fastboot erase data
fastboot erase system
fastboot erase modem
fastboot erase dsp
fastboot erase vbmeta
fastboot erase dtbo
fastboot flash parameter parameter.img
fastboot reboot bootloader
fastboot oem nubia_unlock NUBIA_NX629J
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash splash splash.img
fastboot flash modem NON-HLOS.bin
fastboot flash dtbo dtbo.img
fastboot flash dsp dspso.bin
fastboot flash vbmeta vbmeta.img
fastboot flash -S 100M system system.img
fastboot reboot
It showed device corrupt again
I tried unbrick tool and the twrp you uploaded.
But after installing the twrp, when I try to reboot to recovery, it reboots in fastboot again.
I have tried at least 10-11 times with the above process but no luck.
Please help me out bro this is my only phone and we don't have a service center here.
Best regards,
Dibyank
Click to expand...
Click to collapse
Pm me