Rooting Guide for Doogee Y6-
So waiting time IS Now Finished , twrp is here,
Basic spec-
Ram - 2GB/4GB
Rom- 16GB/64GB
Camera- BACK- 13MP
FRONT- 8MP
Display- 5.5 INCH
OS -MARSHMALLOW
SoC -Mediatek MT6750
Hit Thanks if This Helpful For you:good:
Full Review Checkout HERE
Disclaimer
Code:
your Device At Least 50-60% Charge During Process
warranty Is now Void, Developers and We are Not Responsible For any Damage,
Backup your Personal Data and apps Before Doing anything
take a Nandroid Backup if possible
twrp Installation-
in Short-
Download twrp Sp Flash tools from Bellow Link
Install All Drivers On PC and Run SP tools
Load Scatter File and Check Recovery only
under recovery Section Load Downloaded twrp.img File
Then Click on Download, Connect your Phone to PC [make Sure Phone IS turned off]
Done,
Fastboot Guide-
Bootloader Must be Unlocked,
Code:
Code:
fastboot flash recovery recovery name.img
Rooting Guide-
Download Supersu.zip from Bellow and put into Root Of Sd Card
Boot Device into twrp [use command adb reboot bootloader] or hold power and volume up key on switch of mod
Allow Modification
make a nandroid backup
Click install Zip from sd crad
Locate Downloaded Supersu.zip file and Swipe to install
after Success go back and reboot system now
Done,
Downloads-
mod edit - blog links removed
Phone for stock on bootloop
Phone got stock on bootloop
Please, what can I do,my Doogee y6 could not boot properly again after flashing the above recovery image using sp flash tool.The device can boot into twrp recovery but can't boot back into the. If I flash I new custom ROM Will it be successful as when I Intend to restore in to factory setting, I got ' failed to Mount ' /nvcfg' in valid argument and then done afterwards. Kindly advice me on what to do please. Thank you.
TWRP language
I have question , i flushed twrp from uplink and now my twrp is not in english it is blody chinees language as it is not touch version of twrp....
any solution for this stuff... is it posible to flash maybe some other recovery so it gets english atleast ???
garabadz said:
I have question , i flushed twrp from uplink and now my twrp is not in english it is blody chinees language as it is not touch version of twrp....
any solution for this stuff... is it posible to flash maybe some other recovery so it gets english atleast ???
Click to expand...
Click to collapse
flash this one:
https://forum.xda-developers.com/showpost.php?p=69800037&postcount=3
it's the newest TWRP recovery for Y6 around
I guess you'll be ok
You don't "need" to root
...
chillo71 said:
flash this one:
https://forum.xda-developers.com/showpost.php?p=69800037&postcount=3
it's the newest TWRP recovery for Y6 around
I guess you'll be ok
You don't "need" to root
Click to expand...
Click to collapse
thx dude , but still only chinese 8 lines in old school look maybe i am not doing it well.. i do flash it all good with sptools
how do you enter to twrp?
garabadz said:
thx dude , but still only chinese 8 lines in old school look maybe i am not doing it well.. i do flash it all good with sptools
how do you enter to twrp?
Click to expand...
Click to collapse
oh now I got it, i think you go in the boot menu, all mediateks have that in Chinese
To get into recovery you must press up volume and then hold it along with pressing the power button,
Y6 after a few seconds turn;s on and you then have to chose which mode to go. Up volume to change selection and down volume to select, recovery mode obviously
chillo71 said:
oh now I got it, i think you go in the boot menu, all mediateks have that in Chinese
To get into recovery you must press up volume and then hold it along with pressing the power button,
Y6 after a few seconds turn;s on and you then have to chose which mode to go. Up volume to change selection and down volume to select, recovery mode obviously
Click to expand...
Click to collapse
after doing that i have =killed= android lieing on screen with red triangle.... under it it says =No command=
---------- Post added at 05:28 PM ---------- Previous post was at 04:58 PM ----------
So for new guys in this i skipped very important step when flashed twrp:
Do not run system , but to bootloader first , accept modifications and whoala...
thx @chillo for responding quickly
BTW The dying android means no custom recovery is installed for Y6 , no fastboot command whatsoever
And yes, Y6 and most new android phones from Marshmallow and newer *(edit: ) stock ROMs, don't like to mess with their system partition, one should select system as read-only
Glad you made it through and learned a bit of it
Bootloop
It appears I've soft-bricked my Y6.
I've installed TWRP 3.03 as above and can boot into it but when I try to do a normal reboot I'm stuck in a boot loop.
How do I get to this stage - "Do not run system , but to bootloader first , accept modifications and whoala..." Is that when you first run TWRP?
In the Mount section of TWRP "System" is not ticked but the button "Mount as readonly" is.
If I select Fastboot it hangs. Normal boot hangs. Boot into Recovery is fine.
Any suggestions?
Thanks in advance
Y6 Max:*install recovery with fastboot in Ubuntu Linux
Hello,
thank you for this very useful thread. Just want to add some information on installing the recovery image on the Doogee Y6 Max via fastboot in Ubuntu Linux
I've followed this instructions with some minor (but important)*changes.
First useful information:*to enter in the fastboot mode of the Y6 max do the follow:
- power off your phone
- push togheter Volume up and Power button
now you will see a menu with three options. Move the arrow with Volume up and select "fastboot". Then press Volume down.
You are now in fastboot mode.
Connect your phone via USB to the computer.
Open a terminal and:
- unlock OEM as described in the tutorial linked above.
- install your recovery.img as described in the tutorial linked above
- re-lock the OEM with this command:
Code:
sudo fastboot oem lock
otherwise your phone won't boot.
Then power off your phone and enter in the menu described above pressing toghether Volume up and Power.
Now select "Recovery" and you are done.
Hi! I did everything like in the tutorial but phone is stuck in bootloop after flashing supersu from sd card. Any advices?
I tried 3.0.3 twrp and newest supersu. Phone turned on but there is not root, also there were no errors during instalation.
Related
Hi all,
Well I love my phone, just love it! BUT having bought it from China, like many I am stuck with the Chinese Model and firmware. Huawei Australia have assisted in unlocking the bootloader, now I am ready to root the phone. BUT, I have not had any luck sourcing a root method for it. Can someone please PLEASE help.
I am desperate as it keeps booting me out of Google Play Services, rendering my Huawei watch useless (ironic huh)
Any help would be appreciated. Email me if you like [email protected]
Michael
flash twrp recovery and install root with it very easy way
A Big Thank You and....
rowihel2012 said:
flash twrp recovery and install root with it very easy way
Click to expand...
Click to collapse
That sounds to easy, only question, how do I do that? Is there an instruction manual or guidance anywhere?
I have flashed other phones in the past but this one is stumping me.
I have looked for some of these methods only to be completing surveys that inundate me with spam and phone calls, only to be left without the downloads that I needed. Did I mention how much I love my phone?
Thanks again
Michael
Managed to root my phone.. even when I have updated the EMUI to B018, but there was an issue.. I tell you below
Step I follow from Chinese Forum below...
Preparation step :
1. download the tools from
https://www.mediafire.com/?9drsdo2f6hn4j34
2. Extract the content to your local. Note there are two folders :
- Folder 1 is for the tool that contains the TWRP recovery.img and the adb/fastboot tool,
- Folder 2 is for the original recovery
3. Copy the SuperSU zip to your phone (either in internal or external memory of your phone)
Installation step :
Step 0, unlock your bootloader (search around on how to do it)
1. Since I am using mac, somehow I don't need to install any driver, but if you using windows, install all the driver yourself
2. Enable the developer mode in your phone, and after that enable the usb debugging
3. Turn off your phone, and boot to fastboot (in off mode, connect the phone with your PC then press Volume Up and Power Button together)
4. Since now your phone has been connected to the PC, go to that Tool folder in respective of your OS, then overwrite the recovery with TWRP with fastboot command (install custom recovery) *note : for mac just add "./" in every command
- check the whether its connected : fastboot devices
- install TWRP : fastboot flash recovery recovery.img
5. Restart your phone and boot to recovery
- restart : fastboot reboot
- after reboot, turn off your phone
- reboot to recovery : turn on your phone by holding Volume Down with Power button
- Now you are at TWRP
6. Install SuperSU (root)
- Install SuperSU zip that has already been copied to your phone using TWRP (use the Install mode)
7. Reboot the phone
- Use reboot function in twrp
8. Profit
Theoritically the above things works but I have some issues following the above :
- After step 4, after recovery being flashed with TWRP seems like my phone Boot Partition is being overwritten too
- So when I rebooted the phone, it boot to TWRP instead
- So I tried to re-flashed the recovery with the original EMUI rom recovery (go to the folder "2.P8Max_Official_Recovery(For_restoration)" to find the original recovery.img). Also note that in the this folder, the adb and fastboot is only for mac. The one for windows use it in the tools
- This is done by going to fastboot again, then do command : fastboot flash recovery recovery.img
- This time using the original recovery
- Now when I rebooted the phone, it goes to EMUI recovery, then I just clicked restart to system or something
- After this, everything fixed, and I have SuperSU install and phone rooted
You can follow the above, but do it at your own risk, I am not responsible if your phone brick hehehe..
Original chinese forum is here : http://cn.club.vmall.com/thread-4919441-1-1.html
Click to expand...
Click to collapse
1 min Search
michaeldanielbourke said:
That sounds to easy, only question, how do I do that? Is there an instruction manual or guidance anywhere?
I have flashed other phones in the past but this one is stumping me.
I have looked for some of these methods only to be completing surveys that inundate me with spam and phone calls, only to be left without the downloads that I needed. Did I mention how much I love my phone?
Thanks again
Michael
Click to expand...
Click to collapse
just flash this recovery with fastboot
https://dl.twrp.me/p8/twrp-2.8.7.1-p8.img
fastboot flash recovery twrp-2.8.7.1-p8.img
then enter the recovery with hold power+volume up
install this file with install zip from twrp
https://download.chainfire.eu/696/SuperSU/UPDATE-SuperSU-v2.46.zip?retrieve_file=1
now you have root
very easy
rowihel2012 said:
just flash this recovery with fastboot
https://dl.twrp.me/p8/twrp-2.8.7.1-p8.img
fastboot flash recovery twrp-2.8.7.1-p8.img
then enter the recovery with hold power+volume up
install this file with install zip from twrp
https://download.chainfire.eu/696/SuperSU/UPDATE-SuperSU-v2.46.zip?retrieve_file=1
now you have root
very easy
Click to expand...
Click to collapse
I am so so sorry and a little embarrassed to ask this.
1. I am using the And it sees my phone
2. I am not sure how to fastboot.
3. Do I install the file "install this file with install zip from twrp" onto my device? (p8 max)
Again, I thank you.
michaeldanielbourke said:
I am so so sorry and a little embarrassed to ask this.
1. I am using the And it sees my phone
2. I am not sure how to fastboot.
3. Do I install the file "install this file with install zip from twrp" onto my device? (p8 max)
Again, I thank you.
Click to expand...
Click to collapse
1-shut down the phone
2-connect the usb cable with holding volume down .now you will be in bootloader
3-open cmd command in windows
4-type (fastboot flash recovery recovery.img (you must before rename the recovery file to recovery.img)
5-now after flashing the recovery .hold power+volume up to enter recovery
6-then install the root zip file
7-reboot the phone
You are so so helpful.
rowihel2012 said:
1-shut down the phone
2-connect the usb cable with holding volume down .now you will be in bootloader
3-open cmd command in windows
4-type (fastboot flash recovery recovery.img (you must before rename the recovery file to recovery.img)
5-now after flashing the recovery .hold power+volume up to enter recovery
6-then install the root zip file
7-reboot the phone
Click to expand...
Click to collapse
I will try this when i get home. I am always confused by the process. I am to old for all of this
Michael
BTW you will get in a Bootloop if your dont know how to exit I would not root your phone!
Sadly, this does not work for me. I did everything you suggested and in the command window I get nothing
I know the risks ( I think)
Hirs_E_Fruit said:
BTW you will get in a Bootloop if your dont know how to exit I would not root your phone!
Click to expand...
Click to collapse
Thanks so much for your concern, I know. But I love the phone but need to make it more Android (Google) friendly as it has Chinese firmware which keeps ending any relationship I have with google play services thus rendering the phone useless (almost)
You have been so helpful
rowihel2012 said:
1-shut down the phone
2-connect the usb cable with holding volume down .now you will be in bootloader
3-open cmd command in windows
4-type (fastboot flash recovery recovery.img (you must before rename the recovery file to recovery.img)
5-now after flashing the recovery .hold power+volume up to enter recovery
6-then install the root zip file
7-reboot the phone
Click to expand...
Click to collapse
I did all you suggested and I could not get it to I renamed the file and as you can see I did a command entry and can see my device which is in faboot and rescue mode (phone unlocked) then I type the command you suggested fastboot flash recovery recovery.img and I get this message
I just do not know what I am doing here
Have u unlocked the bootloader?
BTW my method i posted works if u do it right!
michaeldanielbourke said:
I did all you suggested and I could not get it to I renamed the file and as you can see I did a command entry and can see my device which is in faboot and rescue mode (phone unlocked) then I type the command you suggested fastboot flash recovery recovery.img and I get this message
I just do not know what I am doing here
Click to expand...
Click to collapse
The recovery img file link did you downloaded it?
You must download it and but the recovery.img file in fastboot folder
Then rename it to recovery.img.
And open cmd orders from fastboot folder .
Just type
fastboot flash recovery recovery.img
You must download the recovery file into the same folder that you ran your command and in your case "p8 max root". Make sure that the recovery filename is recovery.img instead of some other names.
Sent from my HUAWEI P8max using Tapatalk
Can I just say you have all been so helpful, l am a newb who got cocky and killed my beautiful phone. Now i just get the Huawei logo and no software
What recovery are you on right now? The stock one or twrp?
Sent from my HUAWEI P8max using Tapatalk
Stock
Leechoonhwee said:
What recovery are you on right now? The stock one or twrp?
Sent from my HUAWEI P8max using Tapatalk
Click to expand...
Click to collapse
Hello,
I have twice but now I am stuck on the Huawei logo and powered by Android screen. I can boot into Stock Bootload but no longer TWRP
even though I have reflashed recovery twice. Just chinese language and the EMUI screen with the three options
I think it's time to unroot and flash a new system and do it like i posted, then it will work!
michaeldanielbourke said:
Hello,
I have twice but now I am stuck on the Huawei logo and powered by Android screen. I can boot into Stock Bootload but no longer TWRP
even though I have reflashed recovery twice. Just chinese language and the EMUI screen with the three options
Click to expand...
Click to collapse
Did you reflash recovery2 also?
Hey everyone!
TWRP 2.x For A10-30!
First read bugs before You'll flash it.
So far everything works well. Xposed works great too! .
Guide
Turn off Your device.
Hold Vol up and plug in usb.
From stock recovery select reboot to bootloader.
Now in You computer run following commands:
Fastboot oem unlock
Fastboot flash recovery recovery.img
If You just wanna boot it instead of flashing, type:
Fastboot boot recovery.img
Done. Enjoy!
Download:
Mega.nz
All thanks/donations should go to: @Costi979 he did all the hard work
What works?
For now most things that You will use everday work fine.
Thanks to TWRP Team for making this awesome recovery.
Hi, thanks for your time and effort. Any advice how to get it working or how it can be used?
I'm able to boot into it but I'm lost in the start screen "Unmodified System Partition". Without the touchscreen I cannot use "swipe to allow modifications".
Update: After some fiddling on the screen I was able to enter the twrp. Thanks
Thanks
Stephan
Thanx.But not working for my device. 10-30L . i can't make backup,i can't flash nothing. I think we must wait for official relase...
Found working twrp in 4pda forum but I cannot download because I can't make an account. Must captcha entered and is Russian. Is someone who can help us? Someone who is member on 4pda forum? Thanks in advance !
Do you have the link?
---------- Post added at 06:52 AM ---------- Previous post was at 06:41 AM ----------
snoerenberg said:
Hi, thanks for your time and effort. Any advice how to get it working or how it can be used?
I'm able to boot into it but I'm lost in the start screen "Unmodified System Partition". Without the touchscreen I cannot use "swipe to allow modifications".
Update: After some fiddling on the screen I was able to enter the twrp. Thanks
Thanks
Stephan
Click to expand...
Click to collapse
Hi, what did you do to get around the touchscreen issue?
Just touching it quite often
snoerenberg said:
Just touching it quite often
Click to expand...
Click to collapse
Nice. Was this on Marshmallow?
Thanks for porting TWRP to the TB2 A10-30F/L, @Costi979 and @ProtoDeVNan0! :good:
I've tried booting it first via fastboot boot recovery.img, which worked great, but it fails to backup /system, /boot and /data, as SELinux is still enforced. Building my own kernel based on msm8909_defconf from the Lenovo Support source code for the A10-30F with SELinux disabled in the config worked so far, but now I can't seem to get the touch screen working (which did indeed work with the above attached recovery.img). How did you port TWRP and which kernel (from what source?) did you use? Is there a GitHub repository?
Perdon...este TWRP vale para LENOVO TAB 2 A10-30 TB2 X30F
Gracias, no me atrevo, por que hay varios modelos de TAB2 A10-30, pero si me aconsejais que es para este modelo, genial.
Hi all,
I've tried to recover my Lenovo Tab2 A10-30.
I have done the first 3 steps :
1-Turn off Your device.
2-Hold Vol up and plug in usb.
3-From stock recovery select reboot to bootloader.
but then the tablet stay whith the LENOVO logo (powered by android) and doesn't go to bootloader.
I've tried to wipe data, then reinstall fresh firmware TB2-X30F_S113_160816_ROW_FULLOTA. Tablet runs well, but no reboot on bootloader... (
any idea on how to install recovery.img for TWRP and then supersu ?
thanks for your help, and sorry for my english ;o)
Regards
Sebastien
Power off tablet, power on and keep pressing volume up and down keys. Tablet will boot in bootloader. Connect to pc, device manager will install proper driver. Use QFIL to flash firmware
Costi979 said:
Found working twrp in 4pda forum but I cannot download because I can't make an account. Must captcha entered and is Russian. Is someone who can help us? Someone who is member on 4pda forum? Thanks in advance !
Click to expand...
Click to collapse
Post a link if you know it's really working one so other can try to get it.
Was it for Marshmallow release or Lollipop??
Tablet dead,not necessary .Thanks
---------- Post added at 10:14 AM ---------- Previous post was at 10:11 AM ----------
Barnabe02 said:
Hi all,
I've tried to recover my Lenovo Tab2 A10-30.
I have done the first 3 steps :
1-Turn off Your device.
2-Hold Vol up and plug in usb.
3-From stock recovery select reboot to bootloader.
but then the tablet stay whith the LENOVO logo (powered by android) and doesn't go to bootloader.
I've tried to wipe data, then reinstall fresh firmware TB2-X30F_S113_160816_ROW_FULLOTA. Tablet runs well, but no reboot on bootloader... (
any idea on how to install recovery.img for TWRP and then supersu ?
thanks for your help, and sorry for my english ;o)
Regards
Sebastien
Click to expand...
Click to collapse
Do u have ,in developer options,OEM unlocking enabled?
Working solution.
Rooting LENOVO TAB 2 A10-30
Download and install ADB, Fastboot for windows
https://forum.xda-developers.com/showthread.php?t=2588979
Download TWRP
https://mega.nz/#!hll1HKxQ!fSBwf6fsiLo94mmT_RGNyJ_8KGWlZfA3tDw8tqsgm0o
Another version
https://drive.google.com/file/d/0ByarGoi1dtlkVzN6dlFOanJZZXc/view
Propably working 3.0 TWRP (Haven't tried)
https://mega.nz/#!thszlYzD!UXwqVGY9l4fF4dOdciVWZBOwXF1mSxTlCBZKGaLgYNk
Download supersu recovery flashable.zip
http://www.supersu.com/download
Copy supersu.zip to tablet internal memory
1. Go to settings, system information
2. tap SW version number 5 times to enable developer options
3. Go to developer options menu and Enable USB debugging and open OEM locking
4. Turn off Your device.
5. Hold Vol up and plug in usb.
6. From stock recovery select reboot to bootloader.
7. Now in You computer run following commands:
8. Fastboot oem unlock
9. boot it instead of flashing, type:
Fastboot boot recovery.img
ELSE
if you want to flash it then type:
Fastboot flash recovery recovery.img
From TWRP select install and browse to emmc folder.
install supersu.zip
after installation exit TWRP.
TWRP suggest installing root on exit. Select do not install to exit TWRP.
Now you have root. Enjoy.
Costi979 said:
Do u have ,in developer options,OEM unlocking enabled?
Click to expand...
Click to collapse
Hi,
Yes, OEM unlock is enabled and USB debug also.
RECOVERY MODE is working good (vol up + power) : I can go to RECOVERY. Then I select "Reboot to Bootloader". The tablet reboots but stay in the screen with the LENOVO logo and "Powered by android".
If I start whith buttons (vol up & vol down + power) : same behaviour, tablet stay in Logo screen.
If I start whith down button + power, I can go to the factory meny (with all chineese characters).
Perhaps my bootloader partition is broken ? With RECOVERY MODE, can I reflash it ?
Thanks for your help,
---------- Post added at 11:38 AM ---------- Previous post was at 11:36 AM ----------
Jugehuge said:
Rooting LENOVO TAB 2 A10-30
Download and install ADB, Fastboot for windows
https://forum.xda-developers.com/showthread.php?t=2588979
Download TWRP
https://mega.nz/#!hll1HKxQ!fSBwf6fsiLo94mmT_RGNyJ_8KGWlZfA3tDw8tqsgm0o
Another version
https://drive.google.com/file/d/0ByarGoi1dtlkVzN6dlFOanJZZXc/view
Propably working 3.0 TWRP (Haven't tried)
https://mega.nz/#!thszlYzD!UXwqVGY9l4fF4dOdciVWZBOwXF1mSxTlCBZKGaLgYNk
Download supersu recovery flashable.zip
http://www.supersu.com/download
Copy supersu.zip to tablet internal memory
1. Go to settings, system information
2. tap SW version number 5 times to enable developer options
3. Go to developer options menu and Enable USB debugging and open OEM locking
4. Turn off Your device.
5. Hold Vol up and plug in usb.
6. From stock recovery select reboot to bootloader.
7. Now in You computer run following commands:
8. Fastboot oem unlock
9. boot it instead of flashing, type:
Fastboot boot recovery.img
ELSE
if you want to flash it then type:
Fastboot flash recovery recovery.img
From TWRP select install and browse to emmc folder.
install supersu.zip
after installation exit TWRP.
TWRP suggest installing root on exit. Select do not install to exit TWRP.
Now you have root. Enjoy.
Click to expand...
Click to collapse
Thanks Jugehuge for this sumary.
That's excatllly what I am trying to do. But since I can't enter in Bootloader mode, I can't go further than Step 7 ...
Sebastien
Barnabe02 said:
I select "Reboot to Bootloader". The tablet reboots but stay in the screen with the LENOVO logo and "Powered by android".
Click to expand...
Click to collapse
In bootloader mode tablet shows LENOVO logo etc. It's normal. It's not same like recovery mode where you can see something on screen.
Jugehuge said:
In bootloader mode tablet shows LENOVO logo etc. It's normal. It's not same like recovery mode where you can see something on screen.
Click to expand...
Click to collapse
Many thanks Jugehuge !!! I never thought it was the good screen, always thinking the tablet was on a bootloop ! :silly:
So I've tried Fastboot and IT WORKS like a charm ! many many thanks, I was on this since Christmas !
So TWRP is installed. good.
Now, I have another problem to root : when I tri to install SuperSu, I have an error message in the log saying :
patching sepolicy
----- failure aborting
Click to expand...
Click to collapse
SuperSu is not installed and no root after.
I will try to find why I have this error.
Thanks a lot for your help, very appreciated
Regards,
Sebastien
Check if this help.
https://forum.xda-developers.com/showpost.php?p=68764185&postcount=9
Jugehuge said:
Check if this help.
https://forum.xda-developers.com/showpost.php?p=68764185&postcount=9
Click to expand...
Click to collapse
Thanks Jugehuge, but I don't really understand where I am supposed to find these files for policies...
Nevermind. I wanted to try another TWRP because the one I have installed has a lot of errors (can't stat many folders, ...) Can't return to Fasboot anymore... Can't instal another version of SuperSu (many errors in logs)...
So I will stop my actions, because I have the stange fealing that I will made a big mistake
I will give the tablet to my daughter as this, she will have to restart her games and I will not be able to give her a lot of gems, nor remove the advertisings. But she will be happy to have her tab back !
Many many thanks for your help and to have try to help, but I'm giving up... I've rooted 6 phones and tablet from Samsung in couples of minutes, but for this Lenovo, this is a nightmare for me :silly:
Thanks again
Regards,
Sebastien
Barnabe02 said:
Nevermind. I wanted to try another TWRP because the one I have installed has a lot of errors (can't stat many folders, ...) Can't return to Fasboot anymore... Can't instal another version of SuperSu (many errors in logs)...
Click to expand...
Click to collapse
Hi Sebastien,
Those stat errors are fine. I had them coming also but those didn't prevent from rooting.
It's hard when there isn't much community behind the product. For Samsung products is fairly easy to get rooted as there is community behind them.
One question. Did you download Latest(V2.79):Recovery Flashable.zip from SuperSU??
Hi,
My Honor 6 (Indian Version) was stuck in boot loop post OTA upgrade from B822 to B831. In order to fix this issue, I went through many forums available online and then decided to use the Multi Tool to downgrade to Android L & EMUI 3.1.
To get this done I have followed the below steps:
1. Unlock bootloader
2. Extract BOOT, CUST, RECOVERY and SYSTEM files from the update package downloaded from Honor.in site. //(Honor 6_Firmware_H60-L04_Android 5.1.1_EMUI 3.1_C675B570_India_Flipkart)//
3. Used Multi Tool to unbrick.
Post this the phone is not able to get into recovery mode; it's stuck at the logo screen. It doesnot recognise the 3 button command to boot into recovery mode.
I have tried using the 'boot to recovery' command in Multi Tool but it throws error "daemon not running starting on port 5037".
I have also tried adb command but for some reason my computer does not recognise my mobile.
i.e. adb devices --> doesnot show my device. (yes, I have updated the abb drivers). So I am not able to use any adb commands.
Then i tried installing/flashing CWM & TWRP recovery. None helped. :crying:
Now I am here, out of options and do not know how to proceed.
Could someone in this forum help me fix the current issue? Please.
In addition, I would like to know a few things:
a. How to install a new OS/ROM on a dead phone? (Healthy hardware with corrupt software)
b. How to format any phone and start a fresh installation?
c. How to read internal memory of a phone which has no ROM or corrupt software?
I am new to all this. Please bear with me.
Thanks,
Sampath
sampathnayak09 said:
Hi,
My Honor 6 (Indian Version) was stuck in boot loop post OTA upgrade from B822 to B831. In order to fix this issue, I went through many forums available online and then decided to use the Multi Tool to downgrade to Android L & EMUI 3.1.
To get this done I have followed the below steps:
1. Unlock bootloader
2. Extract BOOT, CUST, RECOVERY and SYSTEM files from the update package downloaded from Honor.in site. //(Honor 6_Firmware_H60-L04_Android 5.1.1_EMUI 3.1_C675B570_India_Flipkart)//
3. Used Multi Tool to unbrick.
Post this the phone is not able to get into recovery mode; it's stuck at the logo screen. It doesnot recognise the 3 button command to boot into recovery mode.
I have tried using the 'boot to recovery' command in Multi Tool but it throws error "daemon not running starting on port 5037".
I have also tried adb command but for some reason my computer does not recognise my mobile.
i.e. adb devices --> doesnot show my device. (yes, I have updated the abb drivers). So I am not able to use any adb commands.
Then i tried installing/flashing CWM & TWRP recovery. None helped. :crying:
Now I am here, out of options and do not know how to proceed.
Could someone in this forum help me fix the current issue? Please.
In addition, I would like to know a few things:
a. How to install a new OS/ROM on a dead phone? (Healthy hardware with corrupt software)
b. How to format any phone and start a fresh installation?
c. How to read internal memory of a phone which has no ROM or corrupt software?
I am new to all this. Please bear with me.
Thanks,
Sampath
Click to expand...
Click to collapse
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
How to return back to Stock Recovery & Install Stock Rom.
muradulislam said:
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
Click to expand...
Click to collapse
I am in a bit different situation, let me explain.
Till day before yesterday I was on B570 Rom, then I upgraded over OTA to B831, then Unlocked Bootloader, Rooted, Installed Latest TWRP Recovery & Installed Latest Xposed Framework, everything went successfull & My phone is running fine.
But the question that arises to me is that none of the Stock Marshmallow update for Honor 6 - H60-L04 has been stable as compared to Lollipop Version & I found B570 super stable & the possibility of myself reverting back to B570 is more. What would be the procedure to revert back to B570.. I think first of all I would have to revert back to stock recovery & then flash the rom package, but how to do this successfully.
Kindly advice.
muradulislam said:
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
Click to expand...
Click to collapse
Thank you for your response. :good:
I have flashed all the files using the fastboot mode, but my phone does not recognise the 3 button command.
It either displays the Honor logo or restarts with a quick vibration. the only command it recognised is 'Vol Down + USB plugged into a computer' (for fastboot).
When flashed with Honor Custom or CWM recovery the phone does not recognise:
1. Vol up + Vol down + Power - for recovery mode
2. Vol down + Power - for hard reset/clear cache partition
When flashed with TWRP recovery the phone only recognises: Power + Vol Up button which boots into recovery mode; however this works only when connected to a power source, the moment I disconnect the power cable the phone switches off.
I tried to install Honor 6 custom ROM EMUI4.0 using TWRP. Need guidance on the below two scenarios.
1. TWRP only recognises .zip files. HONOR custom ROMs are in .app format. What should I do?
2. As a work around, I have downloaded 'Honor 6_Firmware_H60-L04_Andriod 6.0_EMUI 4.0_C432B820_Channel-Others.zip' from xda forum and tried installing it, but TWRP throws a 'no md5 file found' error.
To address this I tried using WinMD5.exe to get the MD5 code and manually created a .MD5 file, but TWRP did not recognise it. Please guide.
Thanks,
Sampath
sampathnayak09 said:
Thank you for your response. :good:
I have flashed all the files using the fastboot mode, but my phone does not recognise the 3 button command.
It either displays the Honor logo or restarts with a quick vibration. the only command it recognised is 'Vol Down + USB plugged into a computer' (for fastboot).
When flashed with Honor Custom or CWM recovery the phone does not recognise:
1. Vol up + Vol down + Power - for recovery mode
2. Vol down + Power - for hard reset/clear cache partition
When flashed with TWRP recovery the phone only recognises: Power + Vol Up button which boots into recovery mode; however this works only when connected to a power source, the moment I disconnect the power cable the phone switches off.
I tried to install Honor 6 custom ROM EMUI4.0 using TWRP. Need guidance on the below two scenarios.
1. TWRP only recognises .zip files. HONOR custom ROMs are in .app format. What should I do?
2. As a work around, I have downloaded 'Honor 6_Firmware_H60-L04_Andriod 6.0_EMUI 4.0_C432B820_Channel-Others.zip' from xda forum and tried installing it, but TWRP throws a 'no md5 file found' error.
To address this I tried using WinMD5.exe to get the MD5 code and manually created a .MD5 file, but TWRP did not recognise it. Please guide.
Thanks,
Sampath
Click to expand...
Click to collapse
@DigiGoon
@sampathnayak09
You need to flash stock recovery first, by executing this command:
Code:
fastboot flash recovery recovery.img
@sampathnayak09
Make sure your power button is working correctly. If the files can be flashed successfully, you should be able to boot into recovery.
Honor firmware can only be flashed using three button method. You can search online for making .zip from .app but I am not sure that will solve your problem.
---------- Post added at 04:10 AM ---------- Previous post was at 04:06 AM ----------
mahadikrs said:
I am in a bit different situation, let me explain.
Till day before yesterday I was on B570 Rom, then I upgraded over OTA to B831, then Unlocked Bootloader, Rooted, Installed Latest TWRP Recovery & Installed Latest Xposed Framework, everything went successfull & My phone is running fine.
But the question that arises to me is that none of the Stock Marshmallow update for Honor 6 - H60-L04 has been stable as compared to Lollipop Version & I found B570 super stable & the possibility of myself reverting back to B570 is more. What would be the procedure to revert back to B570.. I think first of all I would have to revert back to stock recovery & then flash the rom package, but how to do this successfully.
Kindly advice.
Click to expand...
Click to collapse
There are rollback packages for going back. I have read those threads on XDA but could not find them again. Will look for them and will send you a link as soon as I found one.
muradulislam said:
@sampathnayak09
Make sure your power button is working correctly. If the files can be flashed successfully, you should be able to boot into recovery.
Honor firmware can only be flashed using three button method. You can search online for making .zip from .app but I am not sure that will solve your problem.
---------- Post added at 04:10 AM ---------- Previous post was at 04:06 AM ----------
There are rollback packages for going back. I have read those threads on XDA but could not find them again. Will look for them and will send you a link as soon as I found one.
Click to expand...
Click to collapse
Thanks for the reply.
If I extract the recovery.img from the B831 Rom Package & flash the same using the below command will it give me back my stock recovery.
fastboot flash recovery recovery.img
And if once I am on Stock Recovery I hope I can again Install a full fresh copy of the B831 Package which will be with Stock Recovery i.e NO TWRP Recovery & root free. And after that when I get the rollback package I can revert back to B570. Pls advice am I going right or is there any possibility that I will brick my phone.
sampathnayak09 said:
Thank you for your response. :good:
I have flashed all the files using the fastboot mode, but my phone does not recognise the 3 button command.
It either displays the Honor logo or restarts with a quick vibration. the only command it recognised is 'Vol Down + USB plugged into a computer' (for fastboot).
When flashed with Honor Custom or CWM recovery the phone does not recognise:
1. Vol up + Vol down + Power - for recovery mode
2. Vol down + Power - for hard reset/clear cache partition
When flashed with TWRP recovery the phone only recognises: Power + Vol Up button which boots into recovery mode; however this works only when connected to a power source, the moment I disconnect the power cable the phone switches off.
I tried to install Honor 6 custom ROM EMUI4.0 using TWRP. Need guidance on the below two scenarios.
1. TWRP only recognises .zip files. HONOR custom ROMs are in .app format. What should I do?
2. As a work around, I have downloaded 'Honor 6_Firmware_H60-L04_Andriod 6.0_EMUI 4.0_C432B820_Channel-Others.zip' from xda forum and tried installing it, but TWRP throws a 'no md5 file found' error.
To address this I tried using WinMD5.exe to get the MD5 code and manually created a .MD5 file, but TWRP did not recognise it. Please guide.
Thanks,
Sampath
Click to expand...
Click to collapse
If the phone keeps going off you tried charging for a while? Battery might not be charging due to no OS.
Sent from my H60-L04 using XDA Labs
mahadikrs said:
Thanks for the reply.
If I extract the recovery.img from the B831 Rom Package & flash the same using the below command will it give me back my stock recovery.
fastboot flash recovery recovery.img
And if once I am on Stock Recovery I hope I can again Install a full fresh copy of the B831 Package which will be with Stock Recovery i.e NO TWRP Recovery & root free. And after that when I get the rollback package I can revert back to B570. Pls advice am I going right or is there any possibility that I will brick my phone.
Click to expand...
Click to collapse
Try out this thread...
http://forum.xda-developers.com/hon...wngrade-eu-h60-l04-indian-b810-t3367031/page1
My honor 6 bricked about a month ago so can not verify this method but to get out of bootloop, always keep a nandroid backup of your device somewhere safe.
You can make a nandroid backup using twrp. Save it to SD card and then copy it to your PC to keep it safe.
muradulislam said:
Try out this thread...
http://forum.xda-developers.com/hon...wngrade-eu-h60-l04-indian-b810-t3367031/page1
My honor 6 bricked about a month ago so can not verify this method but to get out of bootloop, always keep a nandroid backup of your device somewhere safe.
You can make a nandroid backup using twrp. Save it to SD card and then copy it to your PC to keep it safe.
Click to expand...
Click to collapse
Thanks for your response.
I was able to do as per the steps I mentioned in my earlier post & now I have successfully Downgraded to B570, With Unlocked Bootloader, Rooted, TWRP & Xposed Installed. So its time for me to change my signature.
P.s : Also Updated TWRP to the Latest Version i.e TWRP 3.0.2-0
DigiGoon said:
@sampathnayak09
You need to flash stock recovery first, by executing this command:
Code:
fastboot flash recovery recovery.img
Click to expand...
Click to collapse
Hi,
I did flash the stock recovery, but my phone keeps rebooting and doesn't get into recovery mode.
I am sure it has sufficient battery charge. (Close to 90%).
Is there a way to do a clean install on Android phones? Like the way we install Windows OS on computers. Format hard disks, create partitions and then install a fresh OS?
Thanks
mahadikrs said:
Thanks for your response.
I was able to do as per the steps I mentioned in my earlier post & now I have successfully Downgraded to B570, With Unlocked Bootloader, Rooted, TWRP & Xposed Installed. So its time for me to change my signature.
P.s : Also Updated TWRP to the Latest Version i.e TWRP 3.0.2-0
Click to expand...
Click to collapse
Hi,
Could you please provide links to
1. The downgrade transition package.
2. Latest TWRP version.
Also plz help me understand the benifits of TWRP when it cannot be used to install the stock ROM?
sampathnayak09 said:
Hi,
Could you please provide links to
1. The downgrade transition package.
2. Latest TWRP version.
Also plz help me understand the benifits of TWRP when it cannot be used to install the stock ROM?
Click to expand...
Click to collapse
Find attached below the required links for Rollback package & TWRP.
1) https://club.hihonor.com/in/honor6.217/downgrade-link-from-marshmallow-b831-to-lollipop-b570.7935
2) https://twrp.me/devices/huaweihonor6.html
Regarding TWRP, it lets you install custom roms & other apps which cannot be installed thru stock recovery e.g Xposed Framework. Further TWRP is useful for restoring the phone as it allows to restore the phone by using Nandroid backups taken earlier, provided the Nandroid backups are stored in SD Card. There may be more advantages which I am still trying to find out.
mahadikrs said:
Find attached below the required links for Rollback package & TWRP.
1) https://club.hihonor.com/in/honor6.217/downgrade-link-from-marshmallow-b831-to-lollipop-b570.7935
2) https://twrp.me/devices/huaweihonor6.html
Regarding TWRP, it lets you install custom roms & other apps which cannot be installed thru stock recovery e.g Xposed Framework. Further TWRP is useful for restoring the phone as it allows to restore the phone by using Nandroid backups taken earlier, provided the Nandroid backups are stored in SD Card. There may be more advantages which I am still trying to find out.
Click to expand...
Click to collapse
Thank you for providing the links. Let me try installing these.
muradulislam said:
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
Click to expand...
Click to collapse
goldfinv said:
If the phone keeps going off you tried charging for a while? Battery might not be charging due to no OS.
Sent from my H60-L04 using XDA Labs
Click to expand...
Click to collapse
Phone has 75% + charge as shown in TWRP recovery.
sampathnayak09 said:
Phone has 75% + charge as shown in TWRP recovery.
Click to expand...
Click to collapse
Maybe try flashing one of the custom EMUI ROMs via TWRP?
Sent from my H60-L04 using XDA Labs
@mahadikrs @muradulislam @goldfinv
Thank you for your input guys. I am now able to enter stock recovery mode (3 button mode); however, the installation stops at 5%.
Any suggestions?
sampathnayak09 said:
@[email protected]@goldfinv
Thank you for your input guys. I am now able to enter stock recovery mode (3 button mode); however, the installation stops at 5%.
Any suggestions?
Click to expand...
Click to collapse
Give it a couple of tries. Users have suggested that it usually gets stuck somewhere but trying for 2,3 times gets the job done.
Sent from my PLK-L01 using XDA Labs
sampathnayak09 said:
@mahadikrs @muradulislam @goldfinv
Thank you for your input guys. I am now able to enter stock recovery mode (3 button mode); however, the installation stops at 5%.
Any suggestions?
Click to expand...
Click to collapse
Let me know which Rom version is your phone running now & which version you are trying to migrate to.
Also if 3 button Force update is not working then you can try the project menu option.
But first let me know what state your phone is currently in.
Hi I've unlocked the bootloader of my phone but I can't find any recoveries to push through ADB, therefore I can't flash SU. Does someone have a solution ?
Allright, for the newcomers, I've found a solution for this : (it is very important that you don't update your rom if you've rooted your phone, unless you want a 150$ brick I guess !)
Don't forget to install adb before anything
1. Enable USB debugging in developers option.
2. Connect your phone to a computer and then launch cmd. Type «adb reboot fasboot».
3. Once in fastboot mode we will flash TWRP by typing this : «fastboot flash recovery 1streco.img».
4. Unplug and reboot your device, on the nag screen keep pressing the up volume button to enter recovery. If it doesn't work then choose shutdown and hit all three buttons while it's booting.
5. Once you are in TWRP, backup everything to extsdcard.
6. Go to wipe and format /data and wipe it under advanced wipe. DO NOT TOUCH ANY OTHER PARTITION !!! ONLY DATA.
7. Once it's done reboot the device. You should have a message telling you that the encryption failed, click reset phone.
8. It should launch TWRP choose reboot to bootloader.
9. Once in fastboot mode type this : «fastboot flash recovery 2ndreco.img» then type : «fastboot reboot».
10. Your phone should now display : «Factory reset low level» when you click reset phone. Once it's done it will automatically reboot but don't let it finish his boot sequence yet. On the nag screen keep pressing the up volume to enter recovery and then choose shutdown.
11. Boot in fastboot mode again and type : «fastboot flash recovery 1streco.img», then : «fastboot reboot».
Hold the vol.up button while on nag screen to enter TWRP.
If you don't enter TWRP after you typed fastboot reboot and hit the vol.up button but you enter erecovery that's ok, in this case what you need to do is to choose shutdown. Then hold vol.up, vol.down and power buttons to enter TWRP ! Go to install and flash magiskv13.3.zip and voilà your phone is now rooted !
I've not tried but I think you could restore the data partition with TWRP once you've done all those steps but I can't guarantee you anything so this is why I've told you to backup your data.
1streco.img file link here
2ndreco.img file link here
Magisk v13.3 link here
Si I've been able to install twrp but when I try to flash SuperSu.zip it doesn't work. It's crazy !
For those who wants to know, I've tried everything and the only way to go is to format and wipe data in order to disable dm-verity. But if you do that you won't be able to go further because the rom asks you to crypt your datas before continuing....
Ilovelife76 said:
For those who wants to know, I've tried everything and the only way to go is to format and wipe data in order to disable dm-verity. But if you do that you won't be able to go further because the rom asks you to crypt your datas before continuing....
Click to expand...
Click to collapse
hi, please you can explain me how to obtain root? I have unlocked the bootloader of my phone. Sorry my english. thanks
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Ilovelife76 said:
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Click to expand...
Click to collapse
So, Ilovelife76, have you managed to root your Honor 6C successfully? (And how, if so? )
Ilovelife76 said:
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Click to expand...
Click to collapse
Long-time away from home
I Need to root my Honor 6C... Can anyone help me ?
sub7even12 said:
I Need to root my Honor 6C... Can anyone help me ?
Click to expand...
Click to collapse
He is away from home it seems and no confirmation on rooting. More wait.
Ilovelife76 said:
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Click to expand...
Click to collapse
Still away from home.
Here's the solution
Hi guys ! Sorry for the wait but here it is, my tutorial to the graal, root on this device :
1. Enable USB debugging in developers option.
2. Connect your phone to a computer and then launch cmd. Type «adb reboot fasboot».
3. Once in fastboot mode we will flash TWRP by typing this : «fastboot flash recovery 1streco.img».
4. Unplug and reboot your device, on the nag screen keep pressing the up volume button to enter recovery. If it doesn't work then choose shutdown and hit all three buttons while it's booting.
5. Once you are in TWRP, backup everything to extsdcard.
6. Go to wipe and format /data and wipe it under advanced wipe. DO NOT TOUCH ANY OTHER PARTITION !!! ONLY DATA.
7. Once it's done reboot the device. You should have a message telling you that the encryption failed, click reset phone.
8. It should launch TWRP choose reboot to bootloader.
9. Once in fastboot mode type this : «fastboot flash recovery 2ndreco.img» then type : «fastboot reboot».
10. Your phone should now display : «Factory reset low level» when you click reset phone. Once it's done it will automatically reboot but don't let it finish his boot sequence yet. On the nag screen keep pressing the up volume to enter recovery and then choose shutdown.
11. Boot in fastboot mode again and type : «fastboot flash recovery 1streco.img», then : «fastboot reboot».
Hold the vol.up button while on nag screen to enter TWRP.
If you don't enter TWRP after you typed fastboot reboot and hit the vol.up button but you enter erecovery that's ok, in this case what you need to do is to choose shutdown. Then hold vol.up, vol.down and power buttons to enter TWRP ! Go to install and flash magiskv13.3.zip and voilà your phone is now rooted !
I've not tried but I think you could restore the data partition with TWRP once you've done all those steps but I can't guarantee you anything so this is why I've told you to backup your data.
1streco.img file link here
2ndreco.img file link here
Magisk v13.3 link
Hey, great that you found your way home.
Ilovelife76 said:
1streco.img
2ndreco.img
Click to expand...
Click to collapse
Can you tell us a little more about these two files? Where have you found them? (Not wanting to sound too paranoid but you know...)
I've found 1streco.img on a Chinese board. It's the work of a guy who managed to make TWRP available to us, users of honor 6c. The second one is the standard recovery image of Honor 6c. Those files are good, don't worry. Once your phone is rooted and everything works good, you can of course update magisk through TWRP to the lastest version.
OK, I have been trying around now for an hour or so... I have one real problem and one possible problem:
1. (the real one) Using Win7 64 bit, each time I send the the phone into fastboot mode, the system tries to install "MTP USB device" drivers... without any success so far. That's why the phone boots normally again. I haven't been able to solve that so far (installed HiSuite for example, didn't help).
2. (the possible one) Should the bootloader be unlocked? If yes, I have to admit I haven't found a way to do that so far. :-/
Of course the bootloader must be unlocked before doing anything, you can request a code here on Huawei website : http://en.ui.vmall.com/plugin.php?id=unlock
bravo there is machine back or full backup with recovery
Did you manage to root your phone ?
beautiful, can you install a module on magisk? if yes how because when installing the modules I get a failure when editing magisk.img thanks ?
No, you can't because of dm-verity, you.can manually install via recovery tho.
For the Russian version 6s failed to implant. ADB reboot fastboot this command does not put the phone in fastboot mode.
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Code:
adb reboot bootloader
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Code:
fastboot oem unlock
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
fastboot reboot
Click to expand...
Click to collapse
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!ewVSyI7B!xAvgnzYORGFCtXLyxerNt9hx8Awz-5hNO2vlz5uabfo
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Code:
fastboot flash recovery **DRAG&DROP RECOVERY.IMG HERE**
Press enter
then type
Code:
fastboot reboot
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Code:
adb reboot recovery
and Press Enter
Phone should boot into TWRP
Disconnect from PC
Connect USB-OTG To Phone.
go to Mount and click on Select Storage and Choose USB-OTG
now go to Install and Choose The SUPERSU Update zip file and flash it.
AND REBOOT.
****************************************************************************************
Phone will reboot and during mid boot it will reboot again .... that is totally normal.
and Now Your Device is ROOTED Congrats
****************************************************************************************
If any dev wants to fix the recovery he can do it but give credit where its due .
External SDCard Works and This Recovery might as well work with Panasonic Eluga A3 as they both are identical copies of each other ...
************************************************************************************************************
Rooting With Locked Bootloader.
Pre-Requisites :
1 ) Locked Bootloader
2 ) SP FlashTool --> Download HERE
3 ) TWRP From Above or HERE
4 ) Modified Scatter File from HERE
5 ) Magisk Zip file and Magisk Manager and Keep them in SDCARD OR USB with OTG
******************************************************************************************************************
Flashing Stuff Guide.
Turn off Your Device
Download and Extract the SP Tool to some directory
Download the TWRP and Scatter file and keep them in a folder together
Rename the twrp file to recovery.img
Open SP Flash tool and Load the scatter file.
Below That set the Download Mode to Download Only, Not Firmware upgrade or Format + Download.
Then press the Green Download Button.
OR SEE HERE
Connect the usb cable to your mobile phone and not to the pc
Press and Hold the vol up and vol Down buttons simultaneously and connect the usb cable to the PC.
The Flashtool should Detect your device and start flashing the recovery img.
After completion device should be powered off.
Press and hold the vol UP button while powering up the device to boot into twrp.
In Twrp go to install and change storage to sdcard and locate the magisk zip file and install it.
after installation reboot to system. and install the magisk manager app
Congrats You have successfully rooted your device with a locked bootloader.:laugh::laugh:
Now with magisk you can install Xposed and various other mods systemlessly.
Enjoy
*************************************************************************
For and further inquiries comment below.
Reserved
1) SDCard works fine with recovery
2) Found identical device . Panasonic Eluga A3
3) Will test Recovery of Eluga A3 soon :fingers-crossed:
i have done all the steps you mentioned ..but it stucks on applying update from sd card...
USB-OTG is not showing ...when i try to update through sd card ,,,IT says ""Installation aborted"
bluedrago said:
i have done all the steps you mentioned ..but it stucks on applying update from sd card...
USB-OTG is not showing ...when i try to update through sd card ,,,IT says ""Installation aborted"
Click to expand...
Click to collapse
The Stock System of Noir E2 is Encrypted ..... all nougat based systems are encrypted
You need to backup all data in internal storage to your pc and go to TWRP and Go to Wipe and CLICK ON FORMAT DATA BUTTON
that will remove encryption and allow you to flash zip files
Do you have any custom rom for qmobile e2 like Cm14 rom or miui rom or any other
Bro i want another rom which can be flashed into the qmobile e2.The stock firmware is not good and it lags.
Also i don't like its stock firmware user interface.
So is there any way to flash another rom in it.
I searched alot about it but can't find any rom which can be flashed into it
And u r last hope.
I hope u will have any solution.:good:
Reply must. I am waiting.
Aqdas Iftikhar said:
Bro i want another rom which can be flashed into the qmobile e2.The stock firmware is not good and it lags.
Also i don't like its stock firmware user interface.
So is there any way to flash another rom in it.
I searched alot about it but can't find any rom which can be flashed into it
And u r last hope.
I hope u will have any solution.:good:
Reply must. I am waiting.
Click to expand...
Click to collapse
All I can share with you is the stock rom of Panasonic Eluga A3. If you want that do reply
Yes I Want Bro. Also share the method to port/Flash it. And have u tested it.
andromodgod said:
All I can share with you is the stock rom of Panasonic Eluga A3. If you want that do reply
Click to expand...
Click to collapse
Also tell me if everything is working on Panasonic rom like fingerprint sensor and sdcard etc.
I have read the specs of Panasonic eluga a3 and gsmarena shows that there is no fingerprint sensor in Panasonic eluga a3. So plz tell me that everything is working correctly or there is some bugs.
And share me the method to port/flash that rom.
I will me thankful to you.
Aqdas Iftikhar said:
Also tell me if everything is working on Panasonic rom like fingerprint sensor and sdcard etc.
I have read the specs of Panasonic eluga a3 and gsmarena shows that there is no fingerprint sensor in Panasonic eluga a3. So plz tell me that everything is working correctly or there is some bugs.
And share me the method to port/flash that rom.
I will me thankful to you.
Click to expand...
Click to collapse
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
I got an error in sp flash tool and also Non removable battery problem
andromodgod said:
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
Click to expand...
Click to collapse
The error shown is given below:-
{Initializing scatter file failed. Please check the name of scatter file which you load is legal.}
Also it select only two files:-
1- logo
2- system
Plzz fix this problem and can u plz send me a video tutorial because my device has non removable battery and also not get detected in sp flash tool.
Thanks
---------- Post added at 03:05 PM ---------- Previous post was at 02:30 PM ----------
andromodgod said:
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
Click to expand...
Click to collapse
i old version of sp flash tool the file opens with an error
i tried new version 5.1524.00 but in that version the file even doesnt loads.'
plzz help me i am tired of the bugs which r present in qmobile os.
I will be very very thankful to u.
Aqdas Iftikhar said:
The error shown is given below:-
{Initializing scatter file failed. Please check the name of scatter file which you load is legal.}
Also it select only two files:-
1- logo
2- system
Plzz fix this problem and can u plz send me a video tutorial because my device has non removable battery and also not get detected in sp flash tool.
Thanks
---------- Post added at 03:05 PM ---------- Previous post was at 02:30 PM ----------
i old version of sp flash tool the file opens with an error
i tried new version 5.1524.00 but in that version the file even doesnt loads.'
plzz help me i am tired of the bugs which r present in qmobile os.
I will be very very thankful to u.
Click to expand...
Click to collapse
Download Latest Version of SP Flash tool from http://spflashtool.com
Then extract the Downloaded OS into a separate folder on your desktop.
Then open SPFlash tools and Switch off your device ...
Load the scatter file on to SPFlash tolls that you extracted ... It will be in the OS folder with all the .img files.
Press the start button.
Then connect your device to the PC ... Remember device must be switched off properly.
Flashing should begin automatically.
Many Thanks bro I have flashed the ROM successfully
Thanks for ur help.
After alot of stuggle and with your help I have successfully flashed Panasonic rom.
U said that there will be an update but I checked and it says the software is latest and no upset available.
Why in my phone there is no update??.
Aqdas Iftikhar said:
Thanks for ur help.
After alot of stuggle and with your help I have successfully flashed Panasonic rom.
U said that there will be an update but I checked and it says the software is latest and no upset available.
Why in my phone there is no update??.
Click to expand...
Click to collapse
i forgot ... the link that i shared had the lastest update already .
I tried to root my device and in fast boot i encountered a problem
andromodgod said:
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Code:
adb reboot bootloader
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Code:
fastboot oem unlock
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!KgMVgDwA!ImQoiSBUf9GitR5_K5Dxlzq01P0V4oqsZu5K2-RjZNQ
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Code:
fastboot flash recovery **DRAG&DROP RECOVERY.IMG HERE**
Press enter
then type
Code:
fastboot reboot
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Code:
adb reboot recovery
and Press Enter
Phone should boot into TWRP
Disconnect from PC
Connect USB-OTG To Phone.
go to Mount and click on Select Storage and Choose USB-OTG
now go to Install and Choose The SUPERSU Update zip file and flash it.
AND REBOOT.
****************************************************************************************
Phone will reboot and during mid boot it will reboot again .... that is totally normal.
and Now Your Device is ROOTED Congrats
****************************************************************************************
If any dev wants to fix the recovery he can do it but give credit where its due .
External SDCard Works and This Recovery might as well work with Panasonic Eluga A3 as they both are identical copies of each other ...
************************************************************************************************************
Rooting With Locked Bootloader.
Pre-Requisites :
1 ) Locked Bootloader
2 ) SP FlashTool --> Download HERE
3 ) TWRP From Above or HERE
4 ) Modified Scatter File from HERE
5 ) Magisk Zip file and Magisk Manager and Keep them in SDCARD OR USB with OTG
******************************************************************************************************************
Flashing Stuff Guide.
Turn off Your Device
Download and Extract the SP Tool to some directory
Download the TWRP and Scatter file and keep them in a folder together
Rename the twrp file to recovery.img
Open SP Flash tool and Load the scatter file.
Below That set the Download Mode to Download Only, Not Firmware upgrade or Format + Download.
Then press the Green Download Button.
OR SEE HERE
Connect the usb cable to your mobile phone and not to the pc
Press and Hold the vol up and vol Down buttons simultaneously and connect the usb cable to the PC.
The Flashtool should Detect your device and start flashing the recovery img.
After completion device should be powered off.
Press and hold the vol UP button while powering up the device to boot into twrp.
In Twrp go to install and change storage to sdcard and locate the magisk zip file and install it.
after installation reboot to system. and install the magisk manager app
Congrats You have successfully rooted your device with a locked bootloader.:laugh::laugh:
Now with magisk you can install Xposed and various other mods systemlessly.
Enjoy
*************************************************************************
For and further inquiries comment below.
Click to expand...
Click to collapse
Bro when i booted into fastboot after executing command to unlock bootloader in mobile it says to press volume up key and i pressed it again and again but no response but when i press volume down key it executes instantly and volume down key purpose is to not unlock bootloader.
plzz help me.
also in locked boot loader method sp flash tool says (enable dram failed) and thus i cannot flash recovery
.
plzzz help me out.
i have installed panasonic eluga a3 rom
Aqdas Iftikhar said:
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!KgMVgDwA!ImQoiSBUf9GitR5_K5Dxlzq01P0V4oqsZu5K2-RjZNQ
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Press enter
then type
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Bro when i booted into fastboot after executing command to unlock bootloader in mobile it says to press volume up key and i pressed it again and again but no response but when i press volume down key it executes instantly and volume down key purpose is to not unlock bootloader.
plzz help me.
also in locked boot loader method sp flash tool says (enable dram failed) and thus i cannot flash recovery
.
plzzz help me out.
i have installed panasonic eluga a3 rom
Click to expand...
Click to collapse
After pressing volume up.key few times ... Press the home button . Phone thinks that vol up is home button ... Dunno why that is though ??
andromodgod said:
After pressing volume up.key few times ... Press the home button . Phone thinks that vol up is home button ... Dunno why that is though
Click to expand...
Click to collapse
bro i have unlocked bootloader succesfully.
but when i give command to flash recovery the adb show tranfering and then ok.
but after reboot when i give command to reboot to recovery it boots into panasonic stock recovery.
plzz help me.
and also tell me why sp flash tool is giving me (failed to enable dram error) and give solution.
i hope u will have solution of these matter.
Many Thanks.:fingers-crossed::good:
Aqdas Iftikhar said:
bro i have unlocked bootloader succesfully.
but when i give command to flash recovery the adb show tranfering and then ok.
but after reboot when i give command to reboot to recovery it boots into panasonic stock recovery.
plzz help me.
and also tell me why sp flash tool is giving me (failed to enable dram error) and give solution.
i hope u will have solution of these matter.
Many Thanks.:fingers-crossed::good:
Click to expand...
Click to collapse
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
I have rooted my device but cannot boot into system twrp opens again and again.
andromodgod said:
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
Click to expand...
Click to collapse
Bro after rooting my device i restarted my device but twrp recovery boots again and again and not boot the system.
in twrp i selected to reboot to system but it open twrp recovery again.
i wipe the data and cache but still twrp is openeing.
plzz help me i even cannot acces my device in this situation.
Reply fast.
---------- Post added at 05:46 AM ---------- Previous post was at 05:29 AM ----------
andromodgod said:
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
Click to expand...
Click to collapse
Bro tell me can i relock bootloader and remove or unflash twrp recovery after gaining root access.
if yes tell me how i can remove twrp recovery becasue it is irritating.
Plzz help me out.
When I click Mount/System it returns back to first option (Reboot) with a blink.
I am following first method.
Please help me.
PLzzzzzzzzzzzzzzz
PLz update the link of magisk zip file
The current link is not working. So plz update the link of magisk zip file.
FIXED: Mount Internal Storage in TWRP (Q Mobile Noir E2)
To mount internal storage in TWRP Recovery, Click on Wipe > Format Data > Type "yes" and Click on Ok. Then Reboot into Recovery. Now your Internal Storage is Mounted in TWRP. But it will format whole internal storage and factory reset rom so make a backup before doing this.