I'm in trouble flashing the lollipop 5.02 firmware in my SM-P905M Brazil version (region Portugal P905XXUABOE1_P905OXXABOF1_TPH) already tried with other regions ... using Odin, after try flashing the following error appears on Odin :
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> aboot.mbn
<ID:0/009> NAND Write Start!!
<ID:0/009> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
On my device when I put in download mode the following message appears:
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0X0
KNOX WARRENTY VOID: 0X1
QUALCOMM SECUREBOOT :ENABLE (CSB)
AP SWREV: S1,T1 R1,A1,P1
WRITE PROTECTION: Enable
UDC START
Then in the centre it says Downloading...
Do not turn off target !!
Please somebody help much apreciated
The "M" devices from Latin America have a different modem than any other devices. They support the 700MHz LTE band which is only supported on carrier devices sold in the U.S. Your stuck with what Samsung gives you for your region sadly.
Related
Hello,
I am attempting to flash my phone back to stock using these directions: http://forum.xda-developers.com/showthread.php?t=2586319
When I boot the phone normally, I get the Verizon warning about non-Verizon software. I am able to go to Download mode just fine. I have tried both the ODIN (I've tried JODIN as well) and VZW utility methods and neither is working. I have successfully re-partitioned using the PIT in the link, but the actual tar ball fails. Here is what I get in ODIN 3.07:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone at Download mode says:
CUSTOM BINARY DOWNLOAD: Yes (3 times)
CURRENT BINARY: CUSTOM
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 0
BOOTLOADER AP SWREV: 1
I've done a ton of Googling on this and can't seem to find any answers on what to do. Does anyone have any advice to get this phone working again or is it bricked?
Thanks for any help!
Ok, so it looks like my cable was bad. After switching the cable things seem to be working now.
Dear experts,
after reading many posts regarding this subject I fail to flash my S4 properly. The phone I bought was refurbished and I can't remember what version specific version of operating system it had. I can only remember that it was 4.2.2. I have tried to flash it with stock 5.0.1 which was successful but then the 'Wi-fi' wouldn't turn 'ON' (the switch keeps coming back to 'OFF' position). When I try to flash it back to some stock ROM 4.2.2 like 'Sprint' L720VPUAMDC for example, I keep getting 'FAIL' in Odin3 (v3.10). I have managed to flash one version of 4.2.2 (can't remember which one now) but I still had a problem with 'wi-fi' and on top of that 'samsung keyboard' kept failing as well.
If anyone can help me sort this out, I would be very grateful.
Phone: Samsung S4 (GT-9505)
Product name: SPH-L720T
Download mode message:
Code:
ODIN MODE
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WHITE PROTECTION: Enable
SECURE CHECK FAIL: abort
Odin status message:
Code:
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
Thank you in advance,
Nikola
Hi,
Thanks for writing to us at XDA Assist.
You can post your question in your device forum help section to get further help:
Galaxy S 4 Q&A, Help & Troubleshooting
Good luck!
Hello, here is my problem, I have a tablet GT-N8010 that remains blocked on the logo Samsung, I can not access the mode recovery (it displays the android logo then the tablet reboot) against the downloading mode I can access, odin Recognizes the tablet I tried several official rom but odin always shows me FAILED even with TWR in the recovery mode the tablet display :
Odin mode (in red)
Product name: GT-N8010
CURRENT BINARY: Custom
SYSTEM: Custom
RP swrev: A2 (gray)
Thank you for your help
At what point does Odin fail ??
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> tz.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<<NAND Write fail > search the forum multiple posts .
Probable memory block failure .
Hello,sorry for my english, I have a problem, my phone bootloop yesterday, and I can go to the recovery mode, so I was trying to flash the four parts of my firmware, but it was failed. in param.bin
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
So I try to install a recovery :
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Same problem...
But my downloading mod display :
ODIN MODE
PRODUCT NAME: SM-G925F
CURRENT BINARY: Custom
SYSTEM STATUT: Custom
REACTIVATION LOCK: OFF
Secure download: Enabled
KNOX WARRANTY VOID: 1 (0*0500)
AP SWAEV: B:5 K:2 S:2
KERNEL REV. CHECK FAIL. DEVICE:2, BINARY:1
I can't flashing anyway... I'm lost ! I tried with differents odin3 version, differents rom but always failed...
Please help me
Hi !
There are several threads on the Galaxy S6 Edge Q&A, Help & Troubleshooting
You may have a look here https://forum.xda-developers.com/galaxy-s6-edge/help/bricked-stuck-using-odin-root-t3077615
Important is to have a working Odin version and a good USB cable , if the original doesn`t work , they have a tendency to get damaged for data , use a different one
Good luck !
So I recently bricked my s7 by accidentaly wiping the os in twrp (wich apparently deletes twrp as well since i cant start it). But that should't have been that much of a problem and i tried flashing with odin (v3.09;v3.12.7;v3.13.1) with the newest firmware on samobile (tried android 8.0 and 7.0) but all seems in vain as odin just says sboot.bin FAIL! complete(write) operation failed.
I have also tried with and without re-partition checked since that seems to solve a problem with older odin versions i tried (stuck on set partition).
I would really appreciate any help what so ever.
Big thanks in advance.
ODIN log:
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Necronicaleye said:
So I recently bricked my s7 by accidentaly wiping the os in twrp (wich apparently deletes twrp as well since i cant start it). But that should't have been that much of a problem and i tried flashing with odin (v3.09;v3.12.7;v3.13.1) with the newest firmware on samobile (tried android 8.0 and 7.0) but all seems in vain as odin just says sboot.bin FAIL! complete(write) operation failed.
I have also tried with and without re-partition checked since that seems to solve a problem with older odin versions i tried (stuck on set partition).
I would really appreciate any help what so ever.
Big thanks in advance.
ODIN log:
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It's failing on the boot loader file, post the firmware your trying to flash.
What country are you in?
In download mode what does it list your device as?
Im in Germany and I tried the newest firmware for the sm-g930f, both 8.0 and 7.0 from T-mobile.
In download-mode my device lists these informations:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-G930F
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
FAP LOCK: OFF
SECURE DOWNLOAD ENABLED
WARRANTY VOID: 1 (0x030c)
RP SWREV: B:5 K:3 S:4
File names if needed:
AP_G930FXXU2DRC1_CL12365438_QB17182341_REV00_user_low_ship_meta.tar.md5
BL_G930FXXU2DRC1_CL12365438_QB17182341_REV00_user_low_ship.tar.md5
CP_G930FXXU2DRB6_CL648265_QB8952207_SIGNED.tar.md5
CSC_DDX_G930FDDX2DRC1_CL12631644_QB17182390_REV00_user_low_ship.tar.md5
Necronicaleye said:
Im in Germany and I tried the newest firmware for the sm-g930f, both 8.0 and 7.0 from T-mobile.
In download-mode my device lists these informations:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-G930F
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
FAP LOCK: OFF
SECURE DOWNLOAD ENABLED
WARRANTY VOID: 1 (0x030c)
RP SWREV: B:5 K:3 S:4
File names if needed:
AP_G930FXXU2DRC1_CL12365438_QB17182341_REV00_user_low_ship_meta.tar.md5
BL_G930FXXU2DRC1_CL12365438_QB17182341_REV00_user_low_ship.tar.md5
CP_G930FXXU2DRB6_CL648265_QB8952207_SIGNED.tar.md5
CSC_DDX_G930FDDX2DRC1_CL12631644_QB17182390_REV00_user_low_ship.tar.md5
Click to expand...
Click to collapse
THIS Is the latest firmware for your device, Germany unbranded, you don't need to use T Mobile.
The firmware you are trying to flash is older than the firmware which was already on your device, you cannot downgrade a boot loader ever.
Flash DBT as i've linked above
Thank you very much it worked out just fine ^^
i have the same problem, what software should i install, thanks in advance
SM-G935F
B:8 K:6 S:7