Hello,sorry for my english, I have a problem, my phone bootloop yesterday, and I can go to the recovery mode, so I was trying to flash the four parts of my firmware, but it was failed. in param.bin
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
So I try to install a recovery :
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Same problem...
But my downloading mod display :
ODIN MODE
PRODUCT NAME: SM-G925F
CURRENT BINARY: Custom
SYSTEM STATUT: Custom
REACTIVATION LOCK: OFF
Secure download: Enabled
KNOX WARRANTY VOID: 1 (0*0500)
AP SWAEV: B:5 K:2 S:2
KERNEL REV. CHECK FAIL. DEVICE:2, BINARY:1
I can't flashing anyway... I'm lost ! I tried with differents odin3 version, differents rom but always failed...
Please help me
Hi !
There are several threads on the Galaxy S6 Edge Q&A, Help & Troubleshooting
You may have a look here https://forum.xda-developers.com/galaxy-s6-edge/help/bricked-stuck-using-odin-root-t3077615
Important is to have a working Odin version and a good USB cable , if the original doesn`t work , they have a tendency to get damaged for data , use a different one
Good luck !
Related
I recently tried to unroot my Galaxy Note 10.1 SCH-I925. When I tried to flash the stock firmware on it I get the following:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tired almost every piece of firmware I could find but I have no success . I am still kinda new to flashing firmware but this is my only failure so this has got me stuck. Is there anyone out there with a solution or should sent it to a professional
i have the same problem if you find solution please advice
Hey guys my s7 is stuck on the "Please use Samsung switch emergency recovery" when I try to turn it on. I've tried flashing it back to stock using odin but I keep getting this error. My phone is the G930T model and the frp lock is on. I've tried different odin versions too.
Code:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
hello, make that it's easy
https://www.youtube.com/watch?v=y8AZyalTf5Y
kgmaybe said:
Hey guys my s7 is stuck on the "Please use Samsung switch emergency recovery" when I try to turn it on. I've tried flashing it back to stock using odin but I keep getting this error. My phone is the G930T model and the frp lock is on. I've tried different odin versions too.
Code:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
I've had that problem. The really easy way to fix this is to just flash TWRP through Odin.
Have you tried to do what it told you to do and use Smart Switch? If it doesn't work, you could try to initialize using Smart Switch.
Hi all,
My S7 (rooted) appears to be stuck in a bootloop. Last night, I was using it as normal and set it down to charge overnight.
Woke up this morning, recurring bootloop. Tried to get into recovery, but just got a 'Downloading' screen. Tried to flash a stock firmware (vol down key etc) but got
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
For info, it's rooted, running a custom rom and until yesterday was working fine. No new software has been installed in the past couple of weeks, no settings have been changed.
Any ideas as to how I can get the phone working again?
The "Downloading..." screen is where you need to be to flash stock with ODIN
Make sure to use ODIN 3.12.3 minimum version
I'll give it a go when I get home from work and report back. Seems I was using an older version of Odin (3.11.1). I now have 3.12.3.
Thanks for the reply.
So I loaded a BL, AP, CP & CSC file into Odin (stock 7.0 firmware based on my phone carrier).
Clicked Start:
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> param.bin
<ID:0/003> modem_debug.bin
<ID:0/003> Home Binary Download
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003>
<ID:0/003> FAIL! (DeviceInfo)
<OSM> All threads completed. (succeed 0 / failed 1)
Doesn't seem to like what i'm doing.
<ID:0/003> FAIL! (DeviceInfo)
Do you have a green/blue COM port lit up at the top of ODIN when you connect the phone?
Tried a different USB lead / port?
The Com port info shows in blue. Tried on two different PCs, 2 different official cables, 4 different USB ports.
Getting a bit further:
<ID:0/003> Odin engine v(ID:3.1207)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> param.bin
<ID:0/003> modem_debug.bin
<ID:0/003> Home Binary Download
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> FAIL!
Any thoughts?
I have a Samsung Galaxy S7. It went into a boot loop and then when tried to do factory reset it went into a "recovery booting" loop. Seems only possible to enter download mode. From reading the forums, it seems the only possible option is a flash. I have downloaded Odin 3.13, and the Samsung drivers.
I downloaded file : G930VVRU4CRE5 (which I think is the oreo firmware)
When I "start" the process, it fails:
phone has error : SW REV CHECK FAIL : [aboot] Fused > Binary 4
odin shows:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5219 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Not sure where to go from here ? (do I need different firmware?)
Thank you for the assistance.
cgakdj21 said:
I have a Samsung Galaxy S7. It went into a boot loop and then when tried to do factory reset it went into a "recovery booting" loop. Seems only possible to enter download mode. From reading the forums, it seems the only possible option is a flash. I have downloaded Odin 3.13, and the Samsung drivers.
I downloaded file : G930VVRU4CRE5 (which I think is the oreo firmware)
When I "start" the process, it fails:
phone has error : SW REV CHECK FAIL : [aboot] Fused > Binary 4
odin shows:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5219 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Not sure where to go from here ? (do I need different firmware?)
Thank you for the assistance.
Click to expand...
Click to collapse
You need to use the patched version of Odin and the firmware your using needs to be U4 or above Verizon which I think you already have.
https://forum.xda-developers.com/android/software/patched-odin-3-13-1-t3762572
hey,
I have a problem with my Note 10 plus, i tried to install another firmware ( because i installed busybox and after i had bootloop); now an error shows on the screen " an error has occurred while updating the device software...." i understand that this is download mod ( i cant access download mod or recovery now).
The problem is that when i try to install the firmware with odin it starts but after a while fails, like down below:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 8172 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> dt.img
<ID:0/005> dtbo.img
<ID:0/005> system.img
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
What could i do?
Solved, set just the pit file with nand erese and repartition checked.