Bought this Tab yesterday, seller said it only boots to download mode, he's right!!
I tried rooting and installing recovery and this is what i get
A big red FAIL and
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Am I screwed??
Can this be fixed?? Thanks guys!
You need to restore the partition information table PIT .
How sorry not sure enough to give advice there are a number of posts .
http://forum.xda-developers.com/showthread.php?t=2268735&page=5
Thanks for the help but I need much more help than that. I need a tut or step by step directions. Ive seached everywhere I can think of. I found the one you posted also but I hvae no clue how to use any of the info. I have successfully rooted and fixed a few devices but this is like a whole other level. Thanks
Related
Okay so i just got my replacement today, upgraded to JB and now when i try to flash anything with odin it fails at nand write.
Show for odin status
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> 7z¼¯'
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
CovXX said:
Okay so i just got my replacement today, upgraded to JB and now when i try to flash anything with odin it fails at nand write.
Show for odin status
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> 7z¼¯'
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
From what I have seen in ODIN none of this is right. Added should be 1rst line. Whole script line looks bad to me. Can't tell what you are doing. May need to PM me to avoid a brick.
---------- Post added at 02:48 AM ---------- Previous post was at 02:46 AM ----------
Since post was yesterday Mod may want to close this one. He got it or bricked it. :laugh:
nope didn't get it and isnt bricked either. Tryed again
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRBLK3_Bootchain_CWM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Saw the updated instructions just hours after I posted that. Everything is up and running great!
***********************************
Oh funny I ran across this tread. I just bought an s3 off contract, did the OTA update, and now it seems I can't get root or figure out even what I am doing wrong.
I have spent the better part of a day, bouncing between 3 computers and 4 software environments trying to get all the different guides I have found off of here to work. I have used the toolkit which I realizes states that you must have unlocked bootloader. I try to unlock bootloader, which the instructions seem to suggest that you must root first, I can't get any sort of file permissions to write root files. tried 3 different guides, all at the top of the forum lists.
Below is what I get when I try to flash file in odin per root instructions in tool kit:
*********
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
jerrt010 said:
Saw the updated instructions just hours after I posted that. Everything is up and running great!
***********************************
Oh funny I ran across this tread. I just bought an s3 off contract, did the OTA update, and now it seems I can't get root or figure out even what I am doing wrong.
I have spent the better part of a day, bouncing between 3 computers and 4 software environments trying to get all the different guides I have found off of here to work. I have used the toolkit which I realizes states that you must have unlocked bootloader. I try to unlock bootloader, which the instructions seem to suggest that you must root first, I can't get any sort of file permissions to write root files. tried 3 different guides, all at the top of the forum lists.
Below is what I get when I try to flash file in odin per root instructions in tool kit:
*********
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Click to expand...
Click to collapse
Updated instructions where? I keep getting the same thing. How did you fix it?
Where did you get the updated instructions? Please Tell
Sent from my SCH-I535 using xda app-developers app
hi I've been trying to fix my tablet for the past week and ive been using odin3 1.85 and i have downloaded the stock firmware for samfirmware or sammobile. finally yesterday i got the firmware to work but on to about 80% it would stop when it gets to Hidden.img and i have been searching for a fix or something that i can do to fix it nonstop already and i have not found anything that can fix this problem and im desperate right because i just want to get my tablet up and running perfectly with the stock rom. please help me ill try anythiing that you would think would for my tablet i do have Teamviewer if you are interested in helping me through there and i do have windows 8 and also tried it on windows 7 but its the same error. please and thank you.
the odin message:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> Enter CS for MD5..
<ID:0/007> Leave CS..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is Note forum not Tab .
AS you are on the wrong forum are you trying to flash the wrong firmware as well ???
jje
oops sorry im so retarted i read wrong sorry
Hi,
I'm looking for a threeparted firmware for the galaxy note 2 LTE (N7105). Since im not a native englishspeaker, i have no idea if thats the right Word.
But i already talked to other guys in other forums and they were pretty sure it would work this way.
I already found it here:
http://forum.xda-developers.com/showthread.php?t=2199593
but I can't download it since Hofile is gone.
Could someody please upload it somewhere else or maybe find a new Source?
My Device is broken, i can only reach download-mode and i cant flash without the PIT:
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks
Howdy everyone! Im a new member, but Ive been using the site since the HTC G1 from T-Mobile
I have a G900P Galaxy S5 for Boost Mobile. (It was on 5.0 if that changes anything) I bought the phone, played with it for a few days before I would decide to activate it. I hit the reactivation lock thinking it would be safe if anything were to happen to it, then when I activated it and it updated the Profile, PRL and whatever else for activation, it got pissed off and said
"custom binary blocked by reactivation lock"
Ive tried using Odin to bring me back, but I cannot load the NKD lollipop bootloader, phone says:
SW rev check fail : [tz] Fused 3 > Binary 1
Odin says:
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
I tried adding the stock Rom (G900P_NKD_FullRestore) also using Odin, but that also makes it upset
Odin Says:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now the phone says
Firmware upgrade encountered an issue. Please Select recovery mode in Kies and try again
Do I start to cry over my new paperweight here?
I hope Im not totally dead in the water here. What should I do? and what is possible at this point?
Kies will restore it to latest firmware or you can odin the latest. The phone has newer firmware on it than you where trying to flash it looks like. Cant downgrade to that one.
Ok, if I download a newer firmware, will I need the bootloader installed? Or do I need a newer bootloader too?
If you download the stock firmware it will have the bootloader and all in it. Thats one of the reasons as to why the file is so big. You can download the firmware from your cell provider or you can download one from here http://www.sammobile.com/firmwares/ also, you can find rooted and stock roms here at XDA. Just make sure you download the rom that is for your phone!
got it, Ok cool! Im using Rwilco12's site. Im going to try this again, wish me luck!
IT WORKED!
YAY! Thanks guys!
Same issue
keepinitril said:
got it, Ok cool! Im using Rwilco12's site. Im going to try this again, wish me luck!
IT WORKED!
YAY! Thanks guys!
Click to expand...
Click to collapse
Could you possibly list the steps you used to recover your phone ? i'm having the exact same issue and am trying to restore my phone. I just cannot seem to locate a working download. Also i want to make sure I do everything correctly.
Download Odin
Download your rom from RWilco12
http://rwilco12.com/downloads.php?dir=Files/Devices/
Put your phone into download mode
use Odin (give it time)
done
Thank you! Got it working again. You just saved me getting a whole new phone.
Reactivation Lock
autotech40 said:
Kies will restore it to latest firmware or you can odin the latest. The phone has newer firmware on it than you where trying to flash it looks like. Cant downgrade to that one.
Click to expand...
Click to collapse
I have same issue & and i have running lollipop (bok4) . please give me solution for get rid of reactivation lock. I have tried many roms to flash but field by this error also Rwilco12's.
Odin says:
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
Hi everyone,
This morning i clicked on an app "torque pro" and my phone immediately rebooted itself and got stuck in a constant reboot loop. I couldnt get into stock recovery either. I decided that the only way to bring it back to life would be to flash the stock firmware again via odin.
I have tried for the last 2 hours using different versions of ODIN and Different stock firmwares but i end up getting a write failure everytime around 70% of the way. The log is below:
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1207)..
<ID:0/005> File analysis..
<ID:0/005> Removed!!
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
My phone is technically an ATT S8+ but i had flashed the Canadian Bloatfree firmware before. Does anyone have any suggestions how i can fix this. Smart Switch doesnt even have the option to initialize so i cant force it to flash stock back on the phone.
use a official cable(usb) maybe that will work.
Tried a couple of cables as well as the one that came in the box with the phone... same result unfortunately.
saadi107 said:
Hi everyone,
This morning i clicked on an app "torque pro" and my phone immediately rebooted itself and got stuck in a constant reboot loop. I couldnt get into stock recovery either. I decided that the only way to bring it back to life would be to flash the stock firmware again via odin.
I have tried for the last 2 hours using different versions of ODIN and Different stock firmwares but i end up getting a write failure everytime around 70% of the way. The log is below:
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1207)..
<ID:0/005> File analysis..
<ID:0/005> Removed!!
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
My phone is technically an ATT S8+ but i had flashed the Canadian Bloatfree firmware before. Does anyone have any suggestions how i can fix this. Smart Switch doesnt even have the option to initialize so i cant force it to flash stock back on the phone.
Click to expand...
Click to collapse
Drivers maybe
Drivers are all good. Since I am in Canada and the phone is AT&T... Samsung Canada wouldn't even check what's wrong with it.
Samsung website showed Ubreakifix in Buffalo as an authorized repair facility and I took it there... Thru weren't able to do anything to the phone either.
Just a little bump...
Samsung Canada is being ridiculous and refusing to service a USA phone
Hey you! Here is your fix
1, load into download mode (bixby volume down, power button)
2, click cancel (volume down)
3, load into download mode again
4, click continue (volume up)
5, flash, no error now! No need to flash another bootloader or etc, just every time you want to flash anything use this trick.
Magnerion said:
Hey you! Here is your fix
1, load into download mode (bixby volume down, power button)
2, click cancel (volume down)
3, load into download mode again
4, click continue (volume up)
5, flash, no error now! No need to flash another bootloader or etc, just every time you want to flash anything use this trick.
Click to expand...
Click to collapse
I have the issue to and I tried this method for a few hours and nothing changed. Flash error in Odin is still there.
I saw this guy doing it in a YouTube video. . Looked like the timing of it was very tricky . . . . Did you see the video ?
hth.
I saw a couple of videos in which the guy goes into download mode again the moment he starts Odin.. I've tried that many times but I end up getting the same error. With that being said in my case the BL anf CS files flash without any problems.
The AP file though goes 70% all the time and then stops at "__XmitData_Write" portion. I wonder if there is anyway to find out what that is.
Try if you can flash TWRP with odin.
If successful, format data and wipe everything.
After that try flashing official firmware.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1207)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> abl.elf
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
any solution???