Howdy everyone! Im a new member, but Ive been using the site since the HTC G1 from T-Mobile
I have a G900P Galaxy S5 for Boost Mobile. (It was on 5.0 if that changes anything) I bought the phone, played with it for a few days before I would decide to activate it. I hit the reactivation lock thinking it would be safe if anything were to happen to it, then when I activated it and it updated the Profile, PRL and whatever else for activation, it got pissed off and said
"custom binary blocked by reactivation lock"
Ive tried using Odin to bring me back, but I cannot load the NKD lollipop bootloader, phone says:
SW rev check fail : [tz] Fused 3 > Binary 1
Odin says:
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
I tried adding the stock Rom (G900P_NKD_FullRestore) also using Odin, but that also makes it upset
Odin Says:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now the phone says
Firmware upgrade encountered an issue. Please Select recovery mode in Kies and try again
Do I start to cry over my new paperweight here?
I hope Im not totally dead in the water here. What should I do? and what is possible at this point?
Kies will restore it to latest firmware or you can odin the latest. The phone has newer firmware on it than you where trying to flash it looks like. Cant downgrade to that one.
Ok, if I download a newer firmware, will I need the bootloader installed? Or do I need a newer bootloader too?
If you download the stock firmware it will have the bootloader and all in it. Thats one of the reasons as to why the file is so big. You can download the firmware from your cell provider or you can download one from here http://www.sammobile.com/firmwares/ also, you can find rooted and stock roms here at XDA. Just make sure you download the rom that is for your phone!
got it, Ok cool! Im using Rwilco12's site. Im going to try this again, wish me luck!
IT WORKED!
YAY! Thanks guys!
Same issue
keepinitril said:
got it, Ok cool! Im using Rwilco12's site. Im going to try this again, wish me luck!
IT WORKED!
YAY! Thanks guys!
Click to expand...
Click to collapse
Could you possibly list the steps you used to recover your phone ? i'm having the exact same issue and am trying to restore my phone. I just cannot seem to locate a working download. Also i want to make sure I do everything correctly.
Download Odin
Download your rom from RWilco12
http://rwilco12.com/downloads.php?dir=Files/Devices/
Put your phone into download mode
use Odin (give it time)
done
Thank you! Got it working again. You just saved me getting a whole new phone.
Reactivation Lock
autotech40 said:
Kies will restore it to latest firmware or you can odin the latest. The phone has newer firmware on it than you where trying to flash it looks like. Cant downgrade to that one.
Click to expand...
Click to collapse
I have same issue & and i have running lollipop (bok4) . please give me solution for get rid of reactivation lock. I have tried many roms to flash but field by this error also Rwilco12's.
Odin says:
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
Related
Bought this Tab yesterday, seller said it only boots to download mode, he's right!!
I tried rooting and installing recovery and this is what i get
A big red FAIL and
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Am I screwed??
Can this be fixed?? Thanks guys!
You need to restore the partition information table PIT .
How sorry not sure enough to give advice there are a number of posts .
http://forum.xda-developers.com/showthread.php?t=2268735&page=5
Thanks for the help but I need much more help than that. I need a tut or step by step directions. Ive seached everywhere I can think of. I found the one you posted also but I hvae no clue how to use any of the info. I have successfully rooted and fixed a few devices but this is like a whole other level. Thanks
Hi guys, I need your help this time
I bought SGS Tab 2 10,1 about 1 year ago. Rooted, installed custom rom. Was working till now. After discharge I couldn't turn it on again. Only Download mode and charging works. Can't go to recovery. "Only have Samsung's firmware upgrade encountered an issue. Please select recovery mode in Kies & try again" screen.
I can't install any new recovery. I've tried few version of odin, tried on two PC's. Tried also with diffrent recoverys. I have on both PC's newly installed Win7. Ther's no any Kies. Only installed Samsung USB Drivers.
Used recoveries:
philz_touch_4.96.5-p5100.tar.md5
philz_touch_5.00.5-p5100.tar.md5
shakatu_recovery-clockwork-unofficial-6.0.4.5-p5110
openrecovery-twrp-2.8.5.0-p5100.tar
First few times (diffrent Recov and versions of Odin) I had NAND Write fail.
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_5.00.5-p5100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
After that I downloaded original software, some .tar recovery files etc. Odin showed succes (code below). But it didn't work.
Code:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I watched youtube and it works for most of devices but not for mine.
There is on diffrent between my device and other devices on YT. When Odin showed "<ID:0/005> Removed!!" Tablet turned off. But it didn't turn on like other devices. Insted this, tablet was turned off. After 1-2 min (screen off) odin showed "Passed" but device was still off. When I dissconnected and turned on, there is:
"Samsung's firmware upgrade encountered an issue. Please select recovery mode in Kies & try again".
Even if I try to go to download mode or recovery mode. Don't work. All the time the same screen with "Samsung's firmware upgrade encountered..."
I've used following files:
P5110XXDMI1_P5110OXXDMJ1_HOME.tar
P5110XXDMH2_P5110OXADMH2_HOME.tar.md5
CF-Auto-Root-espresso10wifi-espresso10wifixx-gtp5110.tar.md5
I have no idea how to bring this device to life again. In my opinion (I'm noob) device don't have any bootloader, recovery,kernel or ROM installed. That's way after rebooting using Odin it don't want to show "Samsung" screen. Becouse this mystery thing is not installed.
Is there any way to install all this what phone need in one odin instalation ?
Hello guys.
My Galaxy S7 had a problem once where it was stuck at the Samsung Logo when booting. I took it to a Samsung Rep and they repaired it for me because it was on the warranty period. 3 months after this repair the phone had the same issue, but as it was out of warranty already i flashed a stock rom through odin and it worked. 2 weeks later i was using the phone playing some games while listening to music and then suddenly it restarted and now it boots straight into the "Downloading... please don't turn off" Odin Screen. When i restart the phone it shows the Samsung Galaxy S7 screen real fast and then goes to the "Downloading..." screen, without even showing the "Warning A custom OS...." screen. And when on this screen it does not show the usual Odin screen info on the top left corner. If i try to restart it with the Volume Down, Power and Home sometimes it shows the usual screens for Odin (First the Warning Screen and then the Downloading with the info on the top left corner).
I tried to flash a new firmware but it does not work. I searched a lot on the internet but couldn't find anyone with the same issue, only people who are stuck on odin mode but then when they press the volume down, home and power button the phone boots normally.
This is the Log when i try to flash with HOME_CSC
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> param.bin
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> cm.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And when i try with CSC i get the "No PIT Partition" error. The firmware that was flashed before this last problem is the same i'm trying to flash right now : G930FXXS1BPJC_G930FZTO1BPIF_ZTO (Brazil Unlocked) from 10/11/16. Downloaded on SamMobile
Thanks
icelest said:
Hello guys.
My Galaxy S7 had a problem once where it was stuck at the Samsung Logo when booting. I took it to a Samsung Rep and they repaired it for me because it was on the warranty period. 3 months after this repair the phone had the same issue, but as it was out of warranty already i flashed a stock rom through odin and it worked. 2 weeks later i was using the phone playing some games while listening to music and then suddenly it restarted and now it boots straight into the "Downloading... please don't turn off" Odin Screen. When i restart the phone it shows the Samsung Galaxy S7 screen real fast and then goes to the "Downloading..." screen, without even showing the "Warning A custom OS...." screen. And when on this screen it does not show the usual Odin screen info on the top left corner. If i try to restart it with the Volume Down, Power and Home sometimes it shows the usual screens for Odin (First the Warning Screen and then the Downloading with the info on the top left corner).
I tried to flash a new firmware but it does not work. I searched a lot on the internet but couldn't find anyone with the same issue, only people who are stuck on odin mode but then when they press the volume down, home and power button the phone boots normally.
This is the Log when i try to flash with HOME_CSC
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> param.bin
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> cm.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And when i try with CSC i get the "No PIT Partition" error. The firmware that was flashed before this last problem is the same i'm trying to flash right now : G930FXXS1BPJC_G930FZTO1BPIF_ZTO (Brazil Unlocked) from 10/11/16. Downloaded on SamMobile
Thanks
Click to expand...
Click to collapse
Hi mate
Why is not in warranty still...should be a year
Are you using the latest Odin?
Are you also flashing AP BL & CP?
Go into recovery do a factory reset and try again.......
Try a different stock firmware
MAX 404 said:
Hi mate
Why is not in warranty still...should be a year
Are you using the latest Odin?
Are you also flashing AP BL & CP?
Go into recovery do a factory reset and try again.......
Try a different stock firmware
Click to expand...
Click to collapse
Samsung is denying the warranty because my screen has 2 cracks and they are saying that this problem was caused because of my "bad use" of the smartphone.
Yes. Using Odin 3.12.3.
I'm flashing AP, BL, CP and CSC.
Can't go into recovery. The phone goes straight to the odin screen. Can't do anything other than odin.
Already tried 3 firmwares from my csc (ZTO) and 2 from the Official Stock Rom thread here at XDA.
icelest said:
Samsung is denying the warranty because my screen has 2 cracks and they are saying that this problem was caused because of my "bad use" of the smartphone.
Yes. Using Odin 3.12.3.
I'm flashing AP, BL, CP and CSC.
Can't go into recovery. The phone goes straight to the odin screen. Can't do anything other than odin.
Already tried 3 firmwares from my csc (ZTO) and 2 from the Official Stock Rom thread here at XDA.
Click to expand...
Click to collapse
Try leaving BL out from the flash, only flash the other 3 parts
*Detection* said:
Try leaving BL out from the flash, only flash the other 3 parts
Click to expand...
Click to collapse
This is the log when using the other 3 without the BL
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Try to flash Twrp then make format data and flash custom Rom..
Muhammad Rihawi said:
Try to flash Twrp then make format data and flash custom Rom..
Click to expand...
Click to collapse
Odin Fails to flash TWRP. This is the log:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Don't try flashing anything custom or you'll trip the KNOX warranty uFuse
Phone is still under warranty for 12 months, take it back, the repair failed they should fix it again
icelest said:
Samsung is denying the warranty because my screen has 2 cracks and they are saying that this problem was caused because of my "bad use" of the smartphone.
Yes. Using Odin 3.12.3.
I'm flashing AP, BL, CP and CSC.
Can't go into recovery. The phone goes straight to the odin screen. Can't do anything other than odin.
Already tried 3 firmwares from my csc (ZTO) and 2 from the Official Stock Rom thread here at XDA.
Click to expand...
Click to collapse
icelest said:
This is the log when using the other 3 without the BL
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Hi mate
In your first post you showed that odins fails on this step
cm.bin = Cryptography Manager , the function of this is to avoid downgrades
Do you remember what was the firmware you had? if not try to flash the very latest firmware available
Also i found a very similar case in a a S6 thread , the problem seems like the recovery was missing
http://forum.xda-developers.com/galaxy-s6/help/solved-stuck-download-mode-failed-odin-t3104736
check it out just in case the above solution fails
How to Extract Stock Recovery from Samsung Firmware!
MAX 404 said:
Hi mate
In your first post you showed that odins fails on this step
cm.bin = Cryptography Manager , the function of this is to avoid downgrades
Do you remember what was the firmware you had? if not try to flash the very latest firmware available
Also i found a very similar case in a a S6 thread , the problem seems like the recovery was missing
http://forum.xda-developers.com/galaxy-s6/help/solved-stuck-download-mode-failed-odin-t3104736
check it out just in case the above solution fails
How to Extract Stock Recovery from Samsung Firmware!
Click to expand...
Click to collapse
Thanks for the help. I'll try downloading the latest firmware and flashing it. After that i'll try the solution on the S6 thread. Thank you very much
MAX 404 said:
Hi mate
In your first post you showed that odins fails on this step
cm.bin = Cryptography Manager , the function of this is to avoid downgrades
Do you remember what was the firmware you had? if not try to flash the very latest firmware available
Also i found a very similar case in a a S6 thread , the problem seems like the recovery was missing
http://forum.xda-developers.com/galaxy-s6/help/solved-stuck-download-mode-failed-odin-t3104736
check it out just in case the above solution fails
How to Extract Stock Recovery from Samsung Firmware!
Click to expand...
Click to collapse
When trying the recovery.img method i got this log on Odin
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Currently downloading the latest firmware for tests
MAX 404 said:
Hi mate
In your first post you showed that odins fails on this step
cm.bin = Cryptography Manager , the function of this is to avoid downgrades
Do you remember what was the firmware you had? if not try to flash the very latest firmware available
Also i found a very similar case in a a S6 thread , the problem seems like the recovery was missing
http://forum.xda-developers.com/galaxy-s6/help/solved-stuck-download-mode-failed-odin-t3104736
check it out just in case the above solution fails
How to Extract Stock Recovery from Samsung Firmware!
Click to expand...
Click to collapse
I get this Odin Log when flashing the recovery method as displayed on the S6 thread
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
better try the different firmware but use some chrome or browser downloader to download the firmware not internet download manager.
any downloader which uses the single downloading node not multiple nodes like idm
it happened with me 2 i figured it out using this method.thanx
icelest said:
I get this Odin Log when flashing the recovery method as displayed on the S6 thread
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
What about flashing the latest firmware, you tried?
MAX 404 said:
What about flashing the latest firmware, you tried?
Click to expand...
Click to collapse
With the last firmware i get the same PIT error
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> param.bin
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
icelest said:
With the last firmware i get the same PIT error
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> param.bin
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
hi
are you using CSC or home_csc?
use CSC file it contains the pit file
MAX 404 said:
hi
are you using CSC or home_csc?
use CSC file it contains the pit file
Click to expand...
Click to collapse
With CSC i get this error
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What you have is a hardware fault. Aka brick.
icelest said:
With CSC i get this error
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Hi mate
Did you re installed the Samsung drivers , try a different USB cable....better yet try all this in a different PC, just to make sure all this problems are not PC related
MAX 404 said:
Hi mate
Did you re installed the Samsung drivers , try a different USB cable....better yet try all this in a different PC, just to make sure all this problems are not PC related
Click to expand...
Click to collapse
Hi.
Yeah, tried it on 3 different PCs. Always the same errors :/ I'm guessing it's some hardware issue. Now i'll have to fight Samsung so they fix the phone on warranty
Hi everyone,
This morning i clicked on an app "torque pro" and my phone immediately rebooted itself and got stuck in a constant reboot loop. I couldnt get into stock recovery either. I decided that the only way to bring it back to life would be to flash the stock firmware again via odin.
I have tried for the last 2 hours using different versions of ODIN and Different stock firmwares but i end up getting a write failure everytime around 70% of the way. The log is below:
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1207)..
<ID:0/005> File analysis..
<ID:0/005> Removed!!
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
My phone is technically an ATT S8+ but i had flashed the Canadian Bloatfree firmware before. Does anyone have any suggestions how i can fix this. Smart Switch doesnt even have the option to initialize so i cant force it to flash stock back on the phone.
use a official cable(usb) maybe that will work.
Tried a couple of cables as well as the one that came in the box with the phone... same result unfortunately.
saadi107 said:
Hi everyone,
This morning i clicked on an app "torque pro" and my phone immediately rebooted itself and got stuck in a constant reboot loop. I couldnt get into stock recovery either. I decided that the only way to bring it back to life would be to flash the stock firmware again via odin.
I have tried for the last 2 hours using different versions of ODIN and Different stock firmwares but i end up getting a write failure everytime around 70% of the way. The log is below:
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1207)..
<ID:0/005> File analysis..
<ID:0/005> Removed!!
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
My phone is technically an ATT S8+ but i had flashed the Canadian Bloatfree firmware before. Does anyone have any suggestions how i can fix this. Smart Switch doesnt even have the option to initialize so i cant force it to flash stock back on the phone.
Click to expand...
Click to collapse
Drivers maybe
Drivers are all good. Since I am in Canada and the phone is AT&T... Samsung Canada wouldn't even check what's wrong with it.
Samsung website showed Ubreakifix in Buffalo as an authorized repair facility and I took it there... Thru weren't able to do anything to the phone either.
Just a little bump...
Samsung Canada is being ridiculous and refusing to service a USA phone
Hey you! Here is your fix
1, load into download mode (bixby volume down, power button)
2, click cancel (volume down)
3, load into download mode again
4, click continue (volume up)
5, flash, no error now! No need to flash another bootloader or etc, just every time you want to flash anything use this trick.
Magnerion said:
Hey you! Here is your fix
1, load into download mode (bixby volume down, power button)
2, click cancel (volume down)
3, load into download mode again
4, click continue (volume up)
5, flash, no error now! No need to flash another bootloader or etc, just every time you want to flash anything use this trick.
Click to expand...
Click to collapse
I have the issue to and I tried this method for a few hours and nothing changed. Flash error in Odin is still there.
I saw this guy doing it in a YouTube video. . Looked like the timing of it was very tricky . . . . Did you see the video ?
hth.
I saw a couple of videos in which the guy goes into download mode again the moment he starts Odin.. I've tried that many times but I end up getting the same error. With that being said in my case the BL anf CS files flash without any problems.
The AP file though goes 70% all the time and then stops at "__XmitData_Write" portion. I wonder if there is anyway to find out what that is.
Try if you can flash TWRP with odin.
If successful, format data and wipe everything.
After that try flashing official firmware.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1207)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> abl.elf
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
any solution???
Iv tried Odin with all Bl,AP,CP, and CSC Packages it keeps saying FAIL! (Auth) then a blank log then Complete(Write) operation failed.
For the Samsung smart switch the phone us supported. I have the latest verison and my phone is a Galaxy S7 (Us Cellular) Model: SM-G930R4 still says its not supported.
Im stuck idk what to do and i just want my phone working again! Thank you for the help!
Update: Phone wont enter Recovery Mode nor will start just download mode.
Update: got in to show me i need smart switch recovery. Its says my device is not supported and when i try to recovery feature my phone doesn't appear.
When I apply all BL,Ap ect. It shows
SW REC CHECK FAIL: [aboot]Fused 4 > binary 2
[1] eMMC: write Fail: aboot
When just flashing the AP with odin these are the logs
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Its stuck in on the screen telling me to use smart switch pc software
Wont start to boot or go to recovery.
Tried odin start with re-partion and these are the logs farthest i gotten with no errors popping up on my phone
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> persist.img.ext4
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 1831)
<OSM> All threads completed. (succeed 0 / failed 1)
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
*Detection* said:
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
Click to expand...
Click to collapse
I have been using the modded one this entire time does that mean anything?
*Detection* said:
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
Click to expand...
Click to collapse
I attempted to follow that link so i when through the steps came to step two of downloads and had to find a S7 Snapdragon Root .tar so i did and found this XDA forum https://forum.xda-developers.com/verizon-s7-edge/how-to/root-method-nougat-t3566978 which was the first thing on google searching for the snapdragon.
I followed those steps and i for the error Secure check fail : Boot
I was also able to get it to get into a boot loop once again
When i run odin with the S7_Qualcomm.tar with auto reboot re-partition f. reset time and nand earse all it fails and gives me these logs
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Erase...
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 1831)
<OSM> All threads completed. (succeed 0 / failed 1)
When running the s7_qualcomm.tar file with only auto reboot and r.reset time I get a PASS with these logs
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
But now my phone is in a boot loop with the logo of samsung S7 and the reovery booting.. is also popping up at the same time.
Enisty said:
I have been using the modded one this entire time does that mean anything?
Click to expand...
Click to collapse
Have you tried the non-modded version?
I'd have used that first
ODIN 3.12.3 or newer
*Detection* said:
Have you tried the non-modded version?
I'd have used that first
ODIN 3.12.3 or newer
Click to expand...
Click to collapse
IT WORKS!
I downloaded this file
USC-G930R4TYU4BQK3-20171221083318.zip
Wish I knew where I got it from but now my phone is actually turning on!
There was a loading screen iv never seen before thought it show
Installing applications with a black bar then smart switch popped up and the bar was filled instantly with yellow lol iv just never seen this screen before from
past uses of any Samsung device.
Good stuff, just be cautious with that model S7, it's a snapdragon meaning much more difficult to unbrick if you brick it as the bootloader is locked
*Detection* said:
Good stuff, just be cautious with that model S7, it's a snapdragon meaning much more difficult to unbrick if you brick it as the bootloader is locked
Click to expand...
Click to collapse
Its really buggy the OS itself. Its slower the normal idk if its just because of how fresh it is like the flash maybe just give it time?
Enisty said:
Its really buggy the OS itself. Its slower the normal idk if its just because of how fresh it is like the flash maybe just give it time?
Click to expand...
Click to collapse
Did you factory reset after the flash (or use CSC to force the reset)?
I'd reset it, it should be pretty smooth after maybe 5 mins of first boot