Hi, I flashed Vibe ui 2.0 rom yesterday. And there wasn't any recovery on that ROM so I tried Philz recovery after that my phone started booting into recovery every time.
So I fashed the same ROM again. To test which recovery will work properly I tried CWM recovery. After that my phone is stuck in bootloop.
It just show android icon and than restarts.
Tried to go in recovery by pressing Volume up + Power key doesn't work. Pressing Volume Up + Volume Down + power shows two option
Volume up - Recovery Mode
Volume down - Factory Mode
Click on any option again starts rebooting.
Trying to connect phone to laptop but it even starts rebooting on connecting. So SpFlash Tool is not able to do its work.
Fastboot is also not detecting the phone.
I tried installing USB driver but it says can't be done because driver misses digital signature.
Please suggest me some solution by which I can flash stock ROM or boot into recovery so that I can restore my Backup.
While trying spflash tool..remove ur phone battery
removed the battery but SPTool doesn't detect mobile.
attaching device manager screenshot.
try these
Here are the drivers for windows 7 ,i dont think they work on windows 8 and 8.1..
Try these drivers and try spflash tool again..(not including ur battery in phone)
If the drivers didnt work then try on some pc not laptop...
Coz my phone was also not detecting when connected to laptop but it worked when i connected it to pc.
Just for the safer side.
Follow these steps..
Afte installing drivers ,open spflash tool. Then click on scatter loading and brows the scatter file .then click on download button.
After that connect ur phone (excluding ur battery).
And u r good to go..
These steps works for me like a charm .
And hope it works for u too..
finally got it fixed
Final got it fixed. win 7 driver worked for me. windows 8 wasn't allowing me to install driver without digital signature. Once enabling installation without digital signature SPTool recognized my phone and I flashed the ROM.
Huge relief, I didn't have extra phone to use. Now I can use my phone.Now installed Philz recovery and restoring my backup.
Thanks a lot Sactgr for you help.
Sactgr said:
Here are the drivers for windows 7 ,i dont think they work on windows 8 and 8.1..
Try these drivers and try spflash tool again..(not including ur battery in phone)
If the drivers didnt work then try on some pc not laptop...
Coz my phone was also not detecting when connected to laptop but it worked when i connected it to pc.
Just for the safer side.
Follow these steps..
Afte installing drivers ,open spflash tool. Then click on scatter loading and brows the scatter file .then click on download button.
After that connect ur phone (excluding ur battery).
And u r good to go..
These steps works for me like a charm .
And hope it works for u too..
Click to expand...
Click to collapse
No problemo man ...always happy to help
Related
HELP PLEASE,
sir I m owning a micromax canvas 2 a110 .
recently I rooted my phone ics and flashed CYNUS T2 Rom on my canvas 2 .
when I try to root this rom, nothing happening to me .
tried flash tools as well it just srtuck at 0% no green ring to show progress.
when I choose recovery from path and press f9 to download
I always get an error not all the images are loaded properly you still want to continue I pressed yes nothing happens.
tried cmd as well to flash all commands worked except flashing recovery c:\recovery.img
it shows waiting for device as my device is attached 0123456789abcde
My drivers of mobistel is installed and adb working fine as it can be traced in device manager.
help me to root my jb cynus t2 rom so I can install pre rooted roms thanx....
tanmay5 said:
HELP PLEASE,
sir I m owning a micromax canvas 2 a110 .
recently I rooted my phone ics and flashed CYNUS T2 Rom on my canvas 2 .
when I try to root this rom, nothing happening to me .
tried flash tools as well it just srtuck at 0% no green ring to show progress.
when I choose recovery from path and press f9 to download
I always get an error not all the images are loaded properly you still want to continue I pressed yes nothing happens.
tried cmd as well to flash all commands worked except flashing recovery c:\recovery.img
it shows waiting for device as my device is attached 0123456789abcde
My drivers of mobistel is installed and adb working fine as it can be traced in device manager.
help me to root my jb cynus t2 rom so I can install pre rooted roms thanx....
Click to expand...
Click to collapse
Flash the Stock V2 via the SP Tool.
http://forum.xda-developers.com/show....php?t=1982587 [TUT]MTK Android (Sp flash tool ) tutorial
http://forum.xda-developers.com/show....php?t=1960080 check the first post for the Stock V2 ROM
Even iam facing the same issue sp flash tools cant detect my phone after cynus jb update
mayur.3.92 said:
Even iam facing the same issue sp flash tools cant detect my phone after cynus jb update
Click to expand...
Click to collapse
i think you need the cynus t2 driver..
0. Uninstall the micromax canvas 2 drivers.
1. Install mobistel cynus t2 rom using stock recovery.
2. Connect phone to pc, install mobistel drivers.
3. Remove phone from pc and turn it off. Open device manager in computer. Connect switched off phone to pc. You'll see a device in the COM ports section. Quickly right click it as it vanishes after a few seconds. Right click it and select update device driver.
4. Select the folder in which the cynus t2 drivers are installed. Now the drivers will be installed.
5. Replace the recovery.img with cwm recovery in stock v2 folder.
6. Remove your phone now and let it remain switched off. Open sp flash tool in administrator mode(just in case).
7. Load the scatter loading file and click download button.
8. Connect the phone now. And now everything should go fine.
yeah my mt65xx drivers was not installed after installing i used sp flash tools selected scatter file n recovery pressed download
red bar completes and showing enter usb in 15 sec after that i get an error helpp.............
error 8100 cant find usb port
what should i do know
sir when i use sp flash tool to root jb cynus t2 rom, i selected download when i connected my device it shows 100% with red bar and shows enter usb in 15 sec and after that shows an error 8100 usb port cant be located .
help as com ports are installed for MT65xx and is working properly and named is preloade usb vcom(android) Com 4.
yeah my mt65xx drivers was not installed after installing/updating from drive i selected mobile cynus t2 under program files and said encounted a problem and cant update drivers so i downloaded MT65xx drivers from xda site and browsed and drivers got installed named is preloade usb vcom(android) Com 4. i used sp flash tools selected scatter file n recovery pressed download
red bar completes 100% and showing enter usb in 15 sec after that i get an error helpp.............
error 8100 cant find usb port
what should i do know
this is the error i m getting
tanmay5 said:
this is the error i m getting
Click to expand...
Click to collapse
still no luck ?.
did you try drivers from pdanet?..
did u use "run as admininstrator" for running flashtool... then try without that. because for me, bin4ry rooting donot wrk if i use run as admin option!..
in one tutorial i found
"Please note that, even though it isn't mandatory to select it on the list of images to flash,
preloader file must be present in the same folder as the other partition(s) that you want to flash, or else phone will not be able to enter into download mode."
http://forum.xda-developers.com/showthread.php?t=1982587
so try keeping the cwm recovery.img in the same place as stock recovery was .. ( this is a wild wild gues) ..
Year I m tried a lot of trying I though buying an android will b a good move
But I think I ll stick to windows.
Thanx a lot bro for ur help n effort keep ur work up
I m going 2 sell canvas 2 I thought dev on xda will help me but no one is boughther about jb root
If any news about its root plz tel me
hey , dont loose hope yet bro..i know u hav done all steps correctly. but in my opinion, u need to have more patience ,,..you havent tried all your options yet....
other options are to run spflashtools in a different windows version...may b ur neighbours PC... with drivers freshly installed..
or wait for some jb root tools to come up
mmxa110user said:
hey , dont loose hope yet bro..i know u hav done all steps correctly. but in my opinion, u need to have more patience ,,..you havent tried all your options yet....
other options are to run spflashtools in a different windows version...may b ur neighbours PC... with drivers freshly installed..
or wait for some jb root tools to come up
Click to expand...
Click to collapse
I'll surely wait
thanx dude
if something new comes up please notify me
tk care
Flash tool @ 0%
I tried all possible methods for rooting for months and still the progress bar is @ 0%.... can anyone help me???
you will be given reward in cash.....
pleaseeeeeee.....
Josephxxx said:
I tried all possible methods for rooting for months and still the progress bar is @ 0%.... can anyone help me???
you will be given reward in cash.....
pleaseeeeeee.....
Click to expand...
Click to collapse
Humm it seems all are having similar problem ....
the best solution will be is to proceed freshly i.e format your windows and start again
remember install drivers properly and then use flash tool
see the results n keep posting .....
tanmay5 said:
Humm it seems all are having similar problem ....
the best solution will be is to proceed freshly i.e format your windows and start again
remember install drivers properly and then use flash tool
see the results n keep posting .....
Click to expand...
Click to collapse
If u have CWM or twrp Recovery...just download su update from here - http://download.chainfire.eu/382/SuperSU/UPDATE-SuperSU-v1.93.zip copy it to sd card & flash it via CWM or TWRP. maybe it will help u.
Hi all,
I have a Micromax A110 on which i flashed Ultimate+Galaxy+V4+-+Genuine+Note+3+++S5+UI ROM and BindaasBoost Kernel.
Playstore was not working on this since the ROM installation and it said No Connection always. As suggested by most people i tried some basic steps which didnt work and as final step i did a "Restore to factory Default". Since then the cell is not booting to ROM.(Bricked) :crying:
Its neither getting to CWM recovery as well. Its showing the Note3 logo and then restarts itself. When holding the Power+up+down keys its shows the First screen of recovery mode but soon again shows Note3 boot logo and reboots. Not able to do anything.
Please help Guys !!!
fastboot or adb
VickyPonting said:
Hi all,
I have a Micromax A110 on which i flashed Ultimate+Galaxy+V4+-+Genuine+Note+3+++S5+UI ROM and BindaasBoost Kernel.
Playstore was not working on this since the ROM installation and it said No Connection always. As suggested by most people i tried some basic steps which didnt work and as final step i did a "Restore to factory Default". Since then the cell is not booting to ROM.(Bricked) :crying:
Its neither getting to CWM recovery as well. Its showing the Note3 logo and then restarts itself. When holding the Power+up+down keys its shows the First screen of recovery mode but soon again shows Note3 boot logo and reboots. Not able to do anything.
Please help Guys !!!
Click to expand...
Click to collapse
Can you able to access fastboot or adb ?
Installing SDK ADT
Sakthivel_Subbiah said:
Can you able to access fastboot or adb ?
Click to expand...
Click to collapse
Downloading SDK ADT bundle to check that... (Fingers crossed)
Sakthivel_Subbiah said:
Can you able to access fastboot or adb ?
Click to expand...
Click to collapse
Not getting to ADB or Fastboot as well.. Please help !!!!
Eureka
OMG Finally got it to work.....
Flashing the stock ROM from sptools worked.
I had tried this very first at the beginning but it was not working because incorrect drivers for the cell were installed on my PC (PDANet and vcom)
I removed the incorrect MT65XX drivers using "usbdeview-x64" software.
And then installed the "MT6577 USB VCOM drivers"
then flashed the stock ROM via SPTOOLS and it worked fine..:good:
{ Gosh !!! This was so imp to work as its my WIFE's phone }
VickyPonting said:
OMG Finally got it to work.....
Flashing the stock ROM from sptools worked.
I had tried this very first at the beginning but it was not working because incorrect drivers for the cell were installed on my PC (PDANet and vcom)
I removed the incorrect MT65XX drivers using "usbdeview-x64" software.
And then installed the "MT6577 USB VCOM drivers"
then flashed the stock ROM via SPTOOLS and it worked fine..:good:
{ Gosh !!! This was so imp to work as its my WIFE's phone }
Click to expand...
Click to collapse
:good: always take a backup of your rom... if anything happens you can restore it congrats that you saved your phone...
I rooted my galaxy grand win.. and installed transwin rom. But when I try to connect my phone to pc it's only charging and not able to transfer any data.. and it's not connecting to odin also.. when tried to flash another rom I got stuck in cwm recovery mode for almost 5 days..I searched on Google I found that using stock flash file I can come out of cwm.. so I booted into stock mode using "stock flash zip file" via install zip .. . Now I m not able to boot into cwm recovery mode.. please Help me to connect my phone to pc. And to boot into cwm recovery. Thanks in advance.. rom manager also not helping..now I installed stock rom which I have backed up before.. but still not able to connect with my pc...
Please Help me to boot in cwm recovery and to connect with odin.. ..
Sagar Kininge said:
I rooted my galaxy grand win.. and installed transwin rom. But when I try to connect my phone to pc it's only charging and not able to transfer any data.. and it's not connecting to odin also.. when tried to flash another rom I got stuck in cwm recovery mode for almost 5 days..I searched on Google I found that using stock flash file I can come out of cwm.. so I booted into stock mode using "stock flash zip file" via install zip .. . Now I m not able to boot into cwm recovery mode.. please Help me to connect my phone to pc. And to boot into cwm recovery. Thanks in advance.. rom manager also not helping..now I installed stock rom which I have backed up before.. but still not able to connect with my pc...
Please Help me to boot in cwm recovery and to connect with odin.. ..
Click to expand...
Click to collapse
Turn off your phone and then boot to Download Mode (to do that, press Power, Volume Down and Home button at the same time). If you have your phone's drivers installed on your PC then Odin should recognize your phone. Now go to samsung-updates.com and download your phone's firmware. The link I gave is for GT-I8552 - which I'm assuming is your phone's model number. Once it downloads, flash it using Odin.
Looks like MtpApplication.apk is missing on your phone. That's why you probably can't transfer any files. Either this or something might be wrong with your phone's micro USB port or your USB cable.
You can watch some tutorial videos on YouTube for more info. Good luck!
thanks for reply..
thank u very much for reply...
i solved that problem but now m facing one more problem, on my galaxy grand win 8552 i reinstalled TWRP and after reboot my phone not starting only.. totally dead.. no vibration,no light on pressing of any key.. only when i connect it to my laptop it says unkwn device(beeps like something is connected to pc) even phone is in dead condition.... actually i was running on cwm after directly i installed twrp and after finishing i selected reboot and after that nothing happened and phone not starting only.. no charging logo also.. today i just downloaded stock rom.. nw plzz tell me how to install stock rom..is there any way to flash stock rom?????? i cant enter into cwm ..
plz hel...
thanks for reply..
thank u very much for reply...
i solved that problem but now m facing one more problem, on my galaxy grand win 8552 i reinstalled TWRP and after reboot my phone not starting only.. totally dead.. no vibration,no light on pressing of any key.. only when i connect it to my laptop it says unkwn device(beeps like something is connected to pc) even phone is in dead condition.... actually i was running on cwm after directly i installed twrp and after finishing i selected reboot and after that nothing happened and phone not starting only.. no charging logo also.. today i just downloaded stock rom.. nw plzz tell me how to install stock rom..is there any way to flash stock rom?????? i cant enter into cwm ..
plz help...
Sagar Kininge said:
thank u very much for reply...
i solved that problem but now m facing one more problem, on my galaxy grand win 8552 i reinstalled TWRP and after reboot my phone not starting only.. totally dead.. no vibration,no light on pressing of any key.. only when i connect it to my laptop it says unkwn device(beeps like something is connected to pc) even phone is in dead condition.... actually i was running on cwm after directly i installed twrp and after finishing i selected reboot and after that nothing happened and phone not starting only.. no charging logo also.. today i just downloaded stock rom.. nw plzz tell me how to install stock rom..is there any way to flash stock rom?????? i cant enter into cwm ..
plz help...
Click to expand...
Click to collapse
Looks like you bricked your phone. Are you sure that the TWRP you installed is for your phone? Because this usually happens when you install something that was not made for your phone.
Try to do what I said earlier. Boot to Download Mode. And using Odin flash your phone's firmware. If the damage is not severe then by doing this it should fix your phone. If the damage is severe then perhaps your phone is permanently bricked.
can i install rom through sp tool.. i tried it also but it asking scatter file.. i dont have scatter file of galaxy grand win 8552.. if u have then plz give me its link.. thats my last hope to bring my cell to file..
and that TWEP i installed was not for my cell.. i installed it by mistakly..
plz plz help..
I feel you can try connecting your phone again to odin and flashing a custom recovery made for your phone. That's all of your hopes left if it is not bricked. Pray to god.
Sent from my GT-I9300 using XDA Free mobile app
you need a driver from samsung. The connect thru adb command.
cibalo said:
you need a driver from samsung. The connect thru adb command.
Click to expand...
Click to collapse
i fixed that problem with nearest repair shop.. he said my root file were deleted.. he repaired my phone but before doing that all my phone internal memory was 5.10gb now it became 1.5gb, when i asked him,he said that was necessory because some of your storage got damaged due to flashing wrong recovery(done by me).... so i want to know whatever he said is right???? if yes then is there any possibilities to repair my damaged storage part.....
thanks XDA developers to for answering my all questions thanks a lot ..
I Recently Bought New Lenovo A7000 I was Trying To Install Twrp Recovery In Sp Flash Tool I Accidently Did Formatall+download It Deleted Every thing Including boot I Have Installed A Rom For My Phone All Mtk Drivers Are Installed Like Vcom,Mtk.
I Have Tried Again And Again But Flash Tool Cant Detect My Phone then I Restarted My Pc Remove Phone Battery And Reinstalled Again Then I Opened Sp Flash Tool using administer which Came With my rom i load my rom into spft, usb checkup and emmc checkup was ticked i dont know should i tick of untick i clicked download button unticking preloader and connected phone not detected 1st time not 2nd time not i have tried again and again i dont know which buttons should i press it detected my phone it installed everything but at 100 complete it shows error when checking da dl that error was like security secure usb dl failed i dont know what should i do i again connected it shows same error should i untick checkup Is my phone HARDBRICKED Any Fix Please Help?
Most lenovo phones have meta mode which is used to flash ROMs without preloader.so all you got to do is
1)get your stock ROM
2)load scatter.txt in sp flashtool
3)select either firmware upgrade/download only
4)click download and then connect your powered off phone via usb in meta mode
Note:connecting in meta mode is dffrt for dffrt phones.
Mine is holding vol+ button while connecting,find out how to connect your phone or try some button combinations.
Hello guys,
I have an old phone Infinix note 3 X601 which I haven't used since years, I got it out today and after turning it on I did a reset factory, and after the reset factory was done the phone won't bootup anymore when I turn it on it goes to the boot loader screen and give me this message at the bottom "[!] Data couldn't be decrypted and mounted. Please restart recovery from Power Menu" and when I press restart recovery nothing happens it go back to the same screen, but this is not the official boot loader because back then when I was using it I rooted it and installed Carliv Touch Recovery boatload instead of the official and also I had a custom Rom installed.
Can someone help me, please ?
Also, I tried to flash another rom but when I open SP flash tool it seems that it isn't detecting the phone no matter what I do, tried to install media tek driver auto installer and CDC drivers but nothing happened
I'm using windows 10 latest update
attached a photo of the screen I get when I turn on the phone
thanks in advance.
Have installed latest USB drivers?
Download Infinix USB Driver for Windows (Latest Driver)
Download the latest and original Infinix USB Driver to connect any Infinix Smartphone and Tablets to the Windows Computer quickly.
androidmtk.com
jwoegerbauer said:
Have installed latest USB drivers?
Download Infinix USB Driver for Windows (Latest Driver)
Download the latest and original Infinix USB Driver to connect any Infinix Smartphone and Tablets to the Windows Computer quickly.
androidmtk.com
Click to expand...
Click to collapse
yes I did but still not working
ahmwwd said:
Hello guys,
I have an old phone Infinix note 3 X601 which I haven't used since years, I got it out today and after turning it on I did a reset factory, and after the reset factory was done the phone won't bootup anymore when I turn it on it goes to the boot loader screen and give me this message at the bottom "[!] Data couldn't be decrypted and mounted. Please restart recovery from Power Menu" and when I press restart recovery nothing happens it go back to the same screen, but this is not the official boot loader because back then when I was using it I rooted it and installed Carliv Touch Recovery boatload instead of the official and also I had a custom Rom installed.
Can someone help me, please ?
Also, I tried to flash another rom but when I open SP flash tool it seems that it isn't detecting the phone no matter what I do, tried to install media tek driver auto installer and CDC drivers but nothing happened
I'm using windows 10 latest update
attached a photo of the screen I get when I turn on the phone
thanks in advance.
Click to expand...
Click to collapse
Flash it using SP flash tool
mvikrant97 said:
Flash it using SP flash tool
Click to expand...
Click to collapse
I'm using SP flash tool but the tool doesn't recognize that the phone is connected to the pc
ahmwwd said:
I'm using SP flash tool but the tool doesn't recognize that the phone is connected to the pc
Click to expand...
Click to collapse
Please setup MTK drivers first and add filter using lib usb.