Hi! hello every one.......I'm new to XDA .... and may be I'm posting my problem in wrong discussion ...... any how I having a problem with my mt6589 Clone S4......
Yesterday I was using my phone and it's working fine but when I restart my phone I gets stuck on adroid logo..... I tried wiping cache / factory rest....but no luck...
I'm googling my problem for last 14 to 15 hours but I don't find any help full information......
I tried Installing custom rom by going to recovery mode .....but it gets unknown error....
I tried spflash tool ..... but it asks for enabling usb debugging mode but my stucks on android logo..... now basically my question is that how to turn debugging mode on when my phone get stucks on android logo.....
I also can't install cwm recovery because it's also ask for enabling a debugging mode.......
Shahid Niazi said:
Hi! hello every one.......I'm new to XDA .... and may be I'm posting my problem in wrong discussion ...... any how I having a problem with my mt6589 Clone S4......
Yesterday I was using my phone and it's working fine but when I restart my phone I gets stuck on adroid logo..... I tried wiping cache / factory rest....but no luck...
I'm googling my problem for last 14 to 15 hours but I don't find any help full information......
I tried Installing custom rom by going to recovery mode .....but it gets unknown error....
I tried spflash tool ..... but it asks for enabling usb debugging mode but my stucks on android logo..... now basically my question is that how to turn debugging mode on when my phone get stucks on android logo.....
I also can't install cwm recovery because it's also ask for enabling a debugging mode.......
Click to expand...
Click to collapse
So, you flashed a ROM via cwm.
A few lines later you mention that you can't install cwm... is there something I miss????
Whatever;
Can you enter Fastboot/Flash mode manually/via PC and flash a new ROM from there using Flash Tool?
Have you unlocked your bootloader?
Have you tried following these steps?
That's pretty much everything I can think of.
I hope it's just a software brick... :fingers-crossed:
sonyu said:
So, you flashed a ROM via cwm.
A few lines later you mention that you can't install cwm... is there something I miss????
Whatever;
Can you enter Fastboot/Flash mode manually/via PC and flash a new ROM from there using Flash Tool?
Have you unlocked your bootloader?
Have you tried following these steps?
That's pretty much everything I can think of.
I hope it's just a software brick... :fingers-crossed:
Click to expand...
Click to collapse
No I said I can't install a rom via recovery it gets unknown error ....
But Now I have another question how to enter mt5689 in Fastboot/Flash Mode manually via pc .....with flash tool......
plz can anyone tell how to enable usb debugging mode when phone is bricked.....
if you want to install a stock rom via odin, you dont need usb debugging to be on, just boot into odin/download mode (google to see how) and flash a stock rom, then do whatever you need.
Shahid Niazi said:
Hi! hello every one.......I'm new to XDA .... and may be I'm posting my problem in wrong discussion ...... any how I having a problem with my mt6589 Clone S4......
Yesterday I was using my phone and it's working fine but when I restart my phone I gets stuck on adroid logo..... I tried wiping cache / factory rest....but no luck...
I'm googling my problem for last 14 to 15 hours but I don't find any help full information......
I tried Installing custom rom by going to recovery mode .....but it gets unknown error....
I tried spflash tool ..... but it asks for enabling usb debugging mode but my stucks on android logo..... now basically my question is that how to turn debugging mode on when my phone get stucks on android logo.....
I also can't install cwm recovery because it's also ask for enabling a debugging mode.......
Click to expand...
Click to collapse
Now listen to me very carefully! Don't even try to flash a new firmware to your mobile which is not for your mobile and face the same fate as did! Your place is needrom.com. just contact the site administrator for your device model and he will help you... Believe me!
Hi.....thanx for your reply brother.......
I downloaded the rom from needrom.com for my device mtk6589.....which is actually mtk6572
but after installing a rom with spflash tool....... my hand set gets dead....no usb no display no charging nothing.......
I flashed with spflash tool and process completed successfully with no error... but after installation of rom I safely remove usb of my device ... but when I try to turn my phone on then nothing happen.. now my phone is hard bricked.... Now Plz guide me what I should do now....
I heard from someone that I can be fixed with volcano box....
Plz can anyone tell me..
Did you choose correct model and version?
Sent from my Q900 using XDA Premium 4 mobile app
Kobro said:
if you want to install a stock rom via odin, you dont need usb debugging to be on, just boot into odin/download mode (google to see how) and flash a stock rom, then do whatever you need.
Click to expand...
Click to collapse
You just brought a sigh of relief & smile to my face..
Not just that-you helped me restore my phone with less worry..
Thanks a tonne :angel:
software brick
I have a rooted and unlocked bootloader xperia s. What happened is that I was flashing a new software via cwm and its boot img but its stucks on boot img when restarting phone and I haven't enabled usb debugging so I can't install cwn. So anyone can help me???
henno98.hg said:
I have a rooted and unlocked bootloader xperia s. What happened is that I was flashing a new software via cwm and its boot img but its stucks on boot img when restarting phone and I haven't enabled usb debugging so I can't install cwn. So anyone can help me???
Click to expand...
Click to collapse
same problem here ..?? did u get any solution ??
Please Help...
Saraf Vikyath said:
same problem here ..?? did u get any solution ??
Click to expand...
Click to collapse
Nobody? You got a solution already?
I have a brick Xperia SP with UBL and I tried to relock via flashtool and then repair via Pc Companion, but still detects the modifications...
Guys....my question is how to enable usb debugging on a soft bricked device
help me bricked micrmex express 2 plz
my phone too .. I forgot to switch my USB debugging...
Help!!!!!
henno98.hg said:
I have a rooted and unlocked bootloader xperia s. What happened is that I was flashing a new software via cwm and its boot img but its stucks on boot img when restarting phone and I haven't enabled usb debugging so I can't install cwn. So anyone can help me???
Click to expand...
Click to collapse
Help i have the same problem, put a custom boot loader on an asus zenfone 2 ze551ml and I couldnt get my passcode to work so I put it in recovery mode and wipe devit cache and it took longer than it should so I forced phone off and ever since then the phjone turns on but loops. I have tried to manully put the phone fastboot and doing that but didnt work. and even tried to update from ADB and that even didnt work. I have tried everything but no luck. Please help me. or email me too [email protected]
The bootloader of my htc desire s is locked and the phone is also not turning on , my usb debugging modhe was disabled, now i need to unlock the bootloader . help me please
sonyu said:
So, you flashed a ROM via cwm.
A few lines later you mention that you can't install cwm... is there something I miss????
Whatever;
Can you enter Fastboot/Flash mode manually/via PC and flash a new ROM from there using Flash Tool?
Have you unlocked your bootloader?
Have you tried following these steps?
That's pretty much everything I can think of.
I hope it's just a software brick... :fingers-crossed:
Click to expand...
Click to collapse
hello!,i wanna ask some question
so right now my phone is stuck on boot or bootloop,and i actually have the stable rom in my phone but the name is not "update.zip" and i forgot to enable usb debugging,is there anyway to access my internal storage without usb debugging
my phone is xiaomi mi4,thanks!:good:
---------- Post added at 06:59 AM ---------- Previous post was at 06:54 AM ----------
Kobro said:
if you want to install a stock rom via odin, you dont need usb debugging to be on, just boot into odin/download mode (google to see how) and flash a stock rom, then do whatever you need.
Click to expand...
Click to collapse
hello so my phone is currently in bootloop,i have a stable rom in my internal storage but the name is not update.zip so i cant flash the rom,i forgot to enable usb debugging,is there anyway to access the internal storage via pc without usb debugging?,my current phone is mi4 xiaomi
Thanks!
chandrakaii said:
hello so my phone is currently in bootloop,i have a stable rom in my internal storage but the name is not update.zip so i cant flash the rom,i forgot to enable usb debugging,is there anyway to access the internal storage via pc without usb debugging?,my current phone is mi4 xiaomi
Thanks!
Click to expand...
Click to collapse
Stable rom as in stock rom? or a stable custom rom?
in any case. if you have cwm or twrp you should be able to access the file on your computer, or even transfer it to an sd if the phone has it..
if its a custom rom flashable zip though you you might as well just flash it.
if its a stock rom an you cant aces recovery then you have to redownload it to your pc....
Shahid Niazi said:
Hi.....thanx for your reply brother.......
I downloaded the rom from needrom.com for my device mtk6589.....which is actually mtk6572
but after installing a rom with spflash tool....... my hand set gets dead....no usb no display no charging nothing.......
I flashed with spflash tool and process completed successfully with no error... but after installation of rom I safely remove usb of my device ... but when I try to turn my phone on then nothing happen.. now my phone is hard bricked.... Now Plz guide me what I should do now....
I heard from someone that I can be fixed with volcano box....
Plz can anyone tell me..
Click to expand...
Click to collapse
Now you can't unbrick your phone because you overwritten the preloader of your phone. Remember: when flashing with SP flash tool you mustn't flash the preloader. The preloader is the file that makes possible the flashing with SP and now that you have overwritten it or flashed the wrong one, you probably won't be able to recover it. Take it to service center.
Sent by my iPad using Tapatalk
Hi, I flashed Vibe ui 2.0 rom yesterday. And there wasn't any recovery on that ROM so I tried Philz recovery after that my phone started booting into recovery every time.
So I fashed the same ROM again. To test which recovery will work properly I tried CWM recovery. After that my phone is stuck in bootloop.
It just show android icon and than restarts.
Tried to go in recovery by pressing Volume up + Power key doesn't work. Pressing Volume Up + Volume Down + power shows two option
Volume up - Recovery Mode
Volume down - Factory Mode
Click on any option again starts rebooting.
Trying to connect phone to laptop but it even starts rebooting on connecting. So SpFlash Tool is not able to do its work.
Fastboot is also not detecting the phone.
I tried installing USB driver but it says can't be done because driver misses digital signature.
Please suggest me some solution by which I can flash stock ROM or boot into recovery so that I can restore my Backup.
While trying spflash tool..remove ur phone battery
removed the battery but SPTool doesn't detect mobile.
attaching device manager screenshot.
try these
Here are the drivers for windows 7 ,i dont think they work on windows 8 and 8.1..
Try these drivers and try spflash tool again..(not including ur battery in phone)
If the drivers didnt work then try on some pc not laptop...
Coz my phone was also not detecting when connected to laptop but it worked when i connected it to pc.
Just for the safer side.
Follow these steps..
Afte installing drivers ,open spflash tool. Then click on scatter loading and brows the scatter file .then click on download button.
After that connect ur phone (excluding ur battery).
And u r good to go..
These steps works for me like a charm .
And hope it works for u too..
finally got it fixed
Final got it fixed. win 7 driver worked for me. windows 8 wasn't allowing me to install driver without digital signature. Once enabling installation without digital signature SPTool recognized my phone and I flashed the ROM.
Huge relief, I didn't have extra phone to use. Now I can use my phone.Now installed Philz recovery and restoring my backup.
Thanks a lot Sactgr for you help.
Sactgr said:
Here are the drivers for windows 7 ,i dont think they work on windows 8 and 8.1..
Try these drivers and try spflash tool again..(not including ur battery in phone)
If the drivers didnt work then try on some pc not laptop...
Coz my phone was also not detecting when connected to laptop but it worked when i connected it to pc.
Just for the safer side.
Follow these steps..
Afte installing drivers ,open spflash tool. Then click on scatter loading and brows the scatter file .then click on download button.
After that connect ur phone (excluding ur battery).
And u r good to go..
These steps works for me like a charm .
And hope it works for u too..
Click to expand...
Click to collapse
No problemo man ...always happy to help
I have a GT SGH-i497 from AT&T. I rooted and flashed CWM recovery and CF-Auto-Root-espresso10att-espresso10uc-samsungsghi497.tar.md5 ROM. Everything was working great. Then I decided to flash TWRP recovery via TWRP Android app and not thru recovery, just to check TWRP out. Now tablet will not boot. PC would recognize it in device manager as QHSUSB_DLOAD. I then attempted to push the custom ROM and TWRP to SD card on tablet via ADB/ Fastboot. After doing so the tablet still does not boot and now my PC chimes when I connect the tablet, but in device manager it now says it is unknown. If I hold the power button while connected the PC chimes off and on. I have searched all forums all the way back to 2012, and I have not found any help. Does anyone here know what I can do to get my tablet back? Any and all help is appreciated. Thanks......:good:
Mr_Mxyzptlk said:
I have a GT SGH-i497 from AT&T. I rooted and flashed CWM recovery and CF-Auto-Root-espresso10att-espresso10uc-samsungsghi497.tar.md5 ROM. Everything was working great. Then I decided to flash TWRP recovery via TWRP Android app and not thru recovery, just to check TWRP out. Now tablet will not boot. PC would recognize it in device manager as QHSUSB_DLOAD. I then attempted to push the custom ROM and TWRP to SD card on tablet via ADB/ Fastboot. After doing so the tablet still does not boot and now my PC chimes when I connect the tablet, but in device manager it now says it is unknown. If I hold the power button while connected the PC chimes off and on. I have searched all forums all the way back to 2012, and I have not found any help. Does anyone here know what I can do to get my tablet back? Any and all help is appreciated. Thanks......:good:
Click to expand...
Click to collapse
try with odin and stock firmware
sergio_f said:
try with odin and stock firmware
Click to expand...
Click to collapse
Odin does not recognize the tablet.
ave you installed the drivers??
search for usbdeview, uninstall the drivers of the tablet or all drivers.. then install drivers again
sergio_f said:
ave you installed the drivers??
search for usbdeview, uninstall the drivers of the tablet or all drivers.. then install drivers again
Click to expand...
Click to collapse
Yes, in my initial post I stated that I pushed ROM and TWRP to tablet sdcard via ADB/ Fastboot, I read they install with the android drivers. But I will try the uninstall and search for the usbeview. Thanks for help I will post my findings/ results later this evening. :good:
odin recognize tablet if you boot it in download mode
power & vol buttons
regards
sergio_f said:
ave you installed the drivers??
search for usbdeview, uninstall the drivers of the tablet or all drivers.. then install drivers again
Click to expand...
Click to collapse
usbdeview worked to the driver status. I installed the QHSUSB_DLOAD drivers on PC and the PC now recognizes tablet when connected. Does anyone know where I can download the debrick image for the galaxy tab 2 10.1 AT&T model? Thanks
Mr_Mxyzptlk said:
usbdeview worked to the driver status. I installed the QHSUSB_DLOAD drivers on PC and the PC now recognizes tablet when connected. Does anyone know where I can download the debrick image for the galaxy tab 2 10.1 AT&T model? Thanks
Click to expand...
Click to collapse
There is none available, in my thread I asked the community to share from their working tabs. I haven't got any. Plus nobody has tried that method. It works or is it just a theory? we still don't know.
I Recently Bought New Lenovo A7000 I was Trying To Install Twrp Recovery In Sp Flash Tool I Accidently Did Formatall+download It Deleted Every thing Including boot I Have Installed A Rom For My Phone All Mtk Drivers Are Installed Like Vcom,Mtk.
I Have Tried Again And Again But Flash Tool Cant Detect My Phone then I Restarted My Pc Remove Phone Battery And Reinstalled Again Then I Opened Sp Flash Tool using administer which Came With my rom i load my rom into spft, usb checkup and emmc checkup was ticked i dont know should i tick of untick i clicked download button unticking preloader and connected phone not detected 1st time not 2nd time not i have tried again and again i dont know which buttons should i press it detected my phone it installed everything but at 100 complete it shows error when checking da dl that error was like security secure usb dl failed i dont know what should i do i again connected it shows same error should i untick checkup Is my phone HARDBRICKED Any Fix Please Help?
Most lenovo phones have meta mode which is used to flash ROMs without preloader.so all you got to do is
1)get your stock ROM
2)load scatter.txt in sp flashtool
3)select either firmware upgrade/download only
4)click download and then connect your powered off phone via usb in meta mode
Note:connecting in meta mode is dffrt for dffrt phones.
Mine is holding vol+ button while connecting,find out how to connect your phone or try some button combinations.
My Lenovo A316i does not turn on anymore but can still be recognized by the computer. At first, my phone can be powered on but restarts at the logo. I made it worked using SP Flash Tool and I installed TWRP. The problem occured after I install an updated.zip folder through TWRP without Wiping. The phone at this stage was stocked at the logo. Then I tried the "Format all & Download" option in the SP Flash Tool. Now it does not turn on, but can still be recognized by the computer.
I already followed the steps from these videos
https://www.youtube.com/watch?v=A3TmXtOA0IA
https://www.youtube.com/watch?v=hKYH7gkvrvY
Try to flash with stock rom dude
I already did but it's still not working.
Are u able to go to TWRP recovery mode
No because it's not turning on anymore.
Try to use button combination for your phone model