Database Info

[Q] Downgrade LG P500 to Telus 2.2

I tried to downgrade LG P500 from 2.2.1 to 2.2 by following these steps.
Install msxml.msi from the uncompressed directory
Conect your device (do not turn on disk storage) and run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT
Select PhoneMode : DIAG
In KDZ file : Choose the ROM file you downloaded (V10G_00.kdz file)
Press Launch software update and wait (It will be 10 minutes or so). In your phone it will appear "Emergency mode". Wait until it reboots.
The phone never rebooted. When I manually try to reboot, it comes to Android screen and never gets past it. Has anyone faced this issue?
Thanks.

FIRST TRY TO PRESS THE POWER BUTTON FR FEW SECONDS WHEN ITS SHOWING THE ANDROID SCREEN IF IT LOAD STHEN ITS FINE ORELSE TRY THIS
IT does happen so in order to get it working make sure that u have enable usb debugginng and disable lg modem driver .
Restart ur pc
hold volume up and home button and connect to ur pc via usb
flash using kdz flasher choosing your rom file in diag/emergency/cs emergency(any 1)option
after it succeed flashing it will show battery getting charged but it never turns on on its own so manualy turn on the mobile.
Note : Do not disconnect usb from pc till the android loads up in ur mobile
if all doent work just gv it back to service they will get it repaired

LG Optimus Me P350 stuck in emergency mode

Hello! I tried to update my LG Optimus Me P350 with KDZ Update tool, but the update was unsuccesfull and now the phone is stuck in emergency mode. I can't use any combination of buttons, even when i connect to my pc, this thing remain stuck in emergency mode. What can I do?

Same for me :-(

I found a solution and it's working:
1.Download KDZ updater and uncompress it
http://www.4shared.com/file/UleS4dP3/KDZ_FW_UPD_EN.html
2.Install msxml.msi from the uncompressed directory
3.Charge your battery to almost full state (I'm not sure, but it can be reason if phone doesn't start)
4.Turn phone off somehow (remove battery etc.)
5.Install drivers properly•Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments
•Install the LG drivers by selecting the update manager from the lg site
•Disable LGE Virtual Modem. In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.
6.Press and keep pressed "Volume up"+"Return" and connect USB cable to phone
7.Yellow screen with text emergency mode should appeared
8.Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
9.Run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT (I have one report that CDMA mod works too)
Select PhoneMode : DIAG (in case of fail try EMERGENCY, and as last chance use CS_EMERGENCY)
10.I Recommend do not switch phone off. There was some people, which done it and after they were not be able to turn it on again. If flashing failed, just select some another mode and try it again, again, try shake/connect disconnect, again, again....
11.In KDZ file : Choose the ROM file you downloaded in the first step
12.Press Launch software update
13.Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
14.Make sure that all update was done successfully. Phone should restart itself automatically
15.Disconnect the USB cable from the phone
16.Press the three button combo for HW reset of device i.e volume up + home + power button
KDZ firmware for LG Optimus Me P350:
LG Optimus Me Official Firmwares V10C Download
•[ASEABK] http://csmg.lgmobile.com:9002/LGP350/V10c_00/V10C_00.kdz
LG Optimus Me Firmwares V10E Download:
•[ACISSV] http://depositfiles.com/en/files/4y603iksc
•[ABALSV] http://depositfiles.com/en/files/4vh72o8kn
LG Optimus Me Official Firmwares V10F Download:
•[ACISSV] http://csmg.lgmobile.com:9002/LGP350/V10F_00/V10F_00.kdz
•[ABALSV] http://csmg.lgmobile.com:9002/LGP350/V10F_00/V10F_00.kdz
LG Optimus Me Flasher Tools Download:
•B2C: http://csmg.lgmobile.com:9002/client/app/B2CAppSetup.exe
•KDZ FW Updater: http://www.unclenet.de/files/KDZ_FW_UPD_EN.7z

What i did my phone is i reprogram it

That worked?

link for kdz flash file is not working can u plz update the link

[ROM] How To upgrade or Downgrade LG P940 Prada 3

How to Upgrade or Downgrade LG P940 Prada 3
1. Extract “LGFlashTool 1.2” and instal "Setup_LGFlashTool_1.2.45.921.exe"
2.Replace the file LGFlashTool.exe into C:\LG\LGFlashTool
3. Extract and Install “OMAPFlashInstaller-4.10(2).zip”
4.Exract “LGUnitedModemDriver_WHQL_ML_Ver_4.9.7_All_Win7_LG EAll.zip” and Install “LGUnitedMobileDriver_S497CA20_WHQL_ML_Ver_1.0 .exe ” and “LGUnitedMobileDriver_S497MA20_WHQL_ML_Ver_1.0 .exe ”
5. Turn Off phone, Remove your phone’s SIM and SD cards.
6.Press and hold voll up button in LG P940.
7. When u holding “voll up button” connect the USB cable.
8.When computer detects the new hardware (Omap4430) release “voll up button”.
9. Install the Driver.
10.After Driver installation, go to device manager and change the port “LGE CDMA USB SERIAL PORT” to “com41″.
11. Run LGFlashTool.
12.In DLL select file “LGP940_20120217.dll”
13. In S/W select only *.bin file from “LGP940AT-00-V***-EUR-XXX-***-**-***+0_AP”
14.Choice (Check) “USB” and click OK.
15. Click on Port COM settings(COM plug icon) and select "1"
16.Check as on photos. (host photo is deleted continue in step 17)
17. Click start (The Port 1 window should appear READY).
18.Disconnects USB cable and wait 5 seconds.
19. Press and hold voll up button in Lg P940 and connect USB cable.
20.The update process will begin automatically after that release the “vol up”.
21. When the progress bar reaches 100%, Power ON the LG P940. WAIT 5 MINUT is very slow first boot
If get error 80% (error= the program don't read phone because it restart) no problem go to step 22.
22. Reset the phone after first boot
Driver download:
http://csmg.lgmobile.com:9002/swdata/WEBSW/LGP920/AVIVML/20110623_05/OMAPFlashInstaller-4.10(2).zip
http://csmg.lgmobile.com:9002/data/LGUnitedModemDriver_WHQL_ML_Ver_4.9.7_All_Win7_LGEAll.zip
Sw and Fw:
http://www.mediafire.com/grean89
Same procedure (with photo p920)
http://forum.xda-developers.com/showthread.php?t=1244490
Regards
work 100% tanks for testing "adiif1"

FlashInstaller
Not Found
The requested object does not exist on this server. The link you followed is either outdated, inaccurate, or the server has been instructed not to let you have it.

adiif1 said:
FlashInstaller
Not Found
The requested object does not exist on this server. The link you followed is either outdated, inaccurate, or the server has been instructed not to let you have it.
Click to expand...
Click to collapse
ok fixed link

work thanx!!
all work only have 1 error with 80% (reboot) telephone work good

adiif1 said:
work thanx!!
all work only have 1 error with 80% (reboot) telephone work good
Click to expand...
Click to collapse
yes because the sw flash tool is old 1.2 .. new version 1.3 fix but don't work for me get a reset after first startup

Is this error safe?

adiif1 said:
Is this error safe?
Click to expand...
Click to collapse
yes no problem

great job.
may i ask : V20d+0.part1.rar is same as V20d+0.part2?
or need to be combined?

I respect your work.

hi some questions below:
5. Turn Off phone, Remove your phone’s SIM and SD cards.
with battery? if with battery, will enter: S/W Upgrade mode for step 6&7.
8.When computer detects the new hardware (Omap4430) release “voll up button”.
PC don't detects the New hardware (Omap4430), just install LG driver only. is it right for further step?
17. Click start(The Port 1 window should appear READY).
Don't show Ready.
May help? my phone has problem after kdz flashing.:crying: want to save via this way. :laugh:

Hi
ilovelg4ever said:
5. Turn Off phone, Remove your phone’s SIM and SD cards.
with battery? if with battery, will enter: S/W Upgrade mode for step 6&7.
Click to expand...
Click to collapse
1. after kdz the phone turn on? reset the phone!!
2- 5. no battery into phone... (if don't start S/W without battery instert battery but get error program at finish the update ... no problem error is because phone turn on after 80% automatically but phone is been update) holding “voll up button” and connect cable
ilovelg4ever said:
8.When computer detects the new hardware (Omap4430) release “voll up button”.
PC don't detects the New hardware (Omap4430), just install LG driver only. is it right for further step?
Click to expand...
Click to collapse
3- 8. I recommend reinstall all driver lg + omap
pc don't detect new hardware omap because you having flash KDZ already 'have the drivers on your PC..
ilovelg4ever said:
17. Click start(The Port 1 window should appear READY).
Don't show Ready.
May help? my phone has problem after kdz flashing.:crying: want to save via this way. :laugh:
Click to expand...
Click to collapse
4-17. in computer > go to device manager > looks com ports > your pc read LGE CDMA USB SERIAL PORT? set com41
No > start S/W upgrade phone but the pc don't read the phone test in other pc procedure and if don't work send phone in assistence ...
Yes > go to flash tool Click on Port COM settings (COM plug icon) and select port "1" press start and after you read start u holding “voll up button” connect the USB cable
I hope to have been of helped you

thanks for reply. i work sucessfully. let me share my experience with you.
No exact steps, just some points:
1) Use XP.
2) uninstall all old LG drivers.
3) install OMap & 2 LG drivers.
4) the phone come with battery (if no battery, my pc don't find my phone). Volume up + connect USB.
- Omap didn't appear (i don't know whether the reason is my phone installed OMAP beflore or not).
- Only LG 2-3 drivers to be installed.
5) execute LG flash tool, steps 12-17. Disconnects usb, battery off & in, volume up+connectUSB
6) The update process will begin automatically after that release the “vol up”.
7) phone reboot at 80% (showing "AP download SUccess"), counting continue. (whole procedure finish).
8) few mins later, target is resetting --> reset--..... (showing "Download Fail!)
thnaks grean again.

i have 2 Prada 3.0, the one normal can be flashed vai this way. the another is suck at "S/W screen when i turn it on. but can't be flased via this way, just keep "download fail" after 1-2mins updateing.

ilovelg4ever said:
i have 2 Prada 3.0, the one normal can be flashed vai this way. the another is suck at "S/W screen when i turn it on. but can't be flased via this way, just keep "download fail" after 1-2mins updateing.
Click to expand...
Click to collapse
sorry I can not help you for the second phone!

sorry 2 post

hi did you try to flash via smart flash too?

ilovelg4ever said:
hi did you try to flash via smart flash too?
Click to expand...
Click to collapse
Hi I don t have tested smart flash because crash on my sistem... but if it work on p920 I think that work for prada3..
Sent from my LG-P990 using Tapatalk

..

jbcagampan said:
..
Click to expand...
Click to collapse
read pvt regards

dont work on windows 7 64

[Solved] Optimus 3D Unbricking

Optimus 3D Unbricking And Upgrading
Preparation
1. LG Mobile Drivers http://mediafire.com/?ouuw4u8f9f1gl1d
Download and Install ............
2. LG Flash Tool http://forum.xda-developers.com/attachment.php?attachmentid=2194618&stc=1&d=1376737065
Download And Extract
3.Omap-4-Boot http://forum.xda-developers.com/attachment.php?attachmentid=1641950&d=1358098807
Download And extract to any destination
4.Download And Extract The Firmware Packages For Your Phone
P920 http://d-h.st/RC5
SU760 http://d-h.st/2ag
In these packages u will find
1. .DLL file
2. .BIN file
3. .FLS file
For Bricked Phones
1. Take the battery out and connect the phone to the pc with USB Cable with volume up button pressed and held. Some Drivers Will Be Installed but OMAP4430 Driver Wont Install (specially on win7).Leave Vol . up after driver installation
2.Go In ur Windows Directory suppose C:
Go in c:\windows\system 32
there u will find a file cmd.exe , Run It as Administrator.
3.Type: set devmgr_show_nonpresent_devices=1 and press enter
Then Type devmgmt.msc and press enter device manager will open up.
4.Go in View Menu And check "show Hidden devices"
5. The Omap4430 Device Will be visible Now. Update its driver and choose "select Driver From Specific Location" and guide it to the omap 4 boot folder. there will be a folder named usb_drv_windows in the omap 4 boot folder. guide it to the usb_drv_windows folder and click ok driver search will begin . if asked click on install driver anyway. Then go in ports and open properties of LGE MOBILE USB SERIAL PORT. open advanced tab and change the port to COM 41
6.Open LG Flash tool . In the dll Folder Select the respective .DLL file. In the S/W box select both the .BIN and .FLS file and click ok.
7. Click On the Port Icon (Cable Icon) and select all the ports.
8. Click on the Arrow Icon and u will see many Ready Signs. This is The Flash Ready State.
9.Open Omap 4 boot folder and run "start fast boot.bat" and select your respective device.
10.when u see a msg like "waiting For Device Omap44xx" Take the battery out and connect the phone to the pc via Data cable.
Some Sudden Information Will be displayed . U Have to immediately put the battery in and hold the vol. up till phone boots to download mode.It will be something like S/W blah blah blah for su760
11. Look at ur LG flash tool in the first box the flashing process will start. It will not work if battery is low (YES ITS A FACT)
12. Flashing Process will not Complete but phone will restart and ur phone will be unbricked when it restarts.
13. Again Put The Flash Tool In Flash Ready State
14. Now Remove the Battery .
15. Dont use Omap4boot This time. hold the vol.up button and connect usb cable.Put in the Battery. Phone will boot to Download Mode . Instead if u see the LG logo remove the battery and immediately put it back in while the vol.up is still pressed . do this 1 or 2 times and ur phone will enter download mode. when it enters download mode leave the vol up button.
16. LG flash tool will start flashing when bar reaches 33% to 35%. Phone will restart and Flashing will jump to 80%.
17. Thats it ur phone is unbricked and Fixed. Turn Phone On If It does not turn on automatically and enjoy
For Non- Bricked Phones
1. Open LG Flash Tool Select the .DLL file in the dll box and select the other two .BIN and .FLS file in the S/W box
2. Click On the Port Icon (Cable Icon) and select all the ports.
3. Click on the Arrow Icon and u will see many Ready Signs. This is The Flash Ready State.
4. Now Remove the Battery .
5.Hold the vol.up button and connect usb cable.Put In the Battery. Phone will boot to Download Mode . Instead if u see the LG logo remove the battery and immediately put it back in while the vol.up is still pressed . do this 1 or 2 times and ur phone will enter download mode. when it enters download mode leave the vol up button.
6. LG flash tool will start flashing when bar reaches 33% to 35%. Phone will restart and Flashing will jump to 80%.
7. Thats it ur phone is unbricked and Fixed. Turn Phone On If It does not turn on automatically and enjoy

there is about 2-3 complete and several noncomplete guides for that already

p-vlad said:
there is about 2-3 complete and several noncomplete guides for that already
Click to expand...
Click to collapse
Bro i completed IT just have to find the right LG flash tool which would be easy for people to use

iamtalha said:
Bro i completed IT just have to find the right LG flash tool which would be easy for people to use
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1244490&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=2246001&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=1942836&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=2336215&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=2037287&highlight=unbrick
etc.

p-vlad said:
http://forum.xda-developers.com/showthread.php?t=1244490&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=2246001&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=1942836&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=2336215&highlight=unbrick
http://forum.xda-developers.com/showthread.php?t=2037287&highlight=unbrick
etc.
Click to expand...
Click to collapse
Thats Nice Man . You Can Use Those Guides. You Dont Have To mess with my thread if u dont like it

developers plzzzz help

stuck with the error plzz help flashed stock with odin but remains at setup connection

screenshot

It happened with me sometime back; I tried download mode & it worked. However, recovery mode Home & Power buttons is not accesible.
Take out battery. Re-insert it & "cafefully" press & hold Volume down & Home & Power buttons together & u will enter download mode(yellow triangle). Flash the firmware as usual & see if it works.

not working with one package file it remain at setup connection

1st goto download mode & flash via Odin. U still HAVE download mode. Download mode doesn't vanish in such a case.
This screen in the pic appears when u access download mode & without proper flashing, trying to switch on the phone again. So it shows that symbol.
Do as what I said in the post above.

while using odin
after some process
it get stuck on setup connection

Sanjay(SUN) said:
while using odin
after some process
it get stuck on setup connection
Click to expand...
Click to collapse
Have u made it to download mode or not yet?

done

Which firmware r u flashing? Use Odin v4.42 & filename of ops file should be exactly as BENI_v1.0.ops
I guess u need a froyo(4pkg) firmware.
I tried searching for nearly an hour but couldn't find.

Found the package file
Plz tell me the procedure to flash

Strictly follow the steps mentioned below:
Remember: Don't ever use firmwares made for GT-S5670i/GT-S5670L...etc. on devices like GT-S5670 (no appended alphabet here), coz it will brick ur phone.
First of all,
* Install samsung mobile driver on pc.
* Uninstall Kies(if installed); In some cases, it's also required to disable antivirus/firewall,...etc.(I don't know why).
* Preferably use laptop(for power backup & also it has good usb ports) with XP/Windows7(not Windows8)
* Goto "download mode" in the phone. Then connect it to pc.
* Open Odin v4.42.exe as administrator & you'll see "COM PORT MAPPING" box turned yellow(indicating that you've connected the phone to pc).
Please note that as soon as u select OPS file in the OPS field of Odin, the Odin straightaway displays the device model number in its title bar, regardless of whether ur phone is physically connected to pc or not.
Now set the files(according to which firmware u have) as follows:
For firmware containing 4 files(Note the beginning filenames)
OPS: BENI_v1.0.ops
BOOT: APBOOT_S5670.....
PHONE: MODEM_S5670.....
PDA: CODE_S5670.....
CSC: CSC_5670.....
Click "Start" & wait till Odin says "PASS". Don't touch ur phone during the process. Ur phone will reboot during the process & that's perfectly normal.
OR for firmware containing one file(Note the beginning filename)
Tick "One Package" field(below com port).
Now set the files as follows:
OPS: BENI_v1.0.ops
One Package: S5670...._HOME.tar.md5
Click "Start" & wait till Odin says "PASS". Don't touch ur phone during the process. Ur phone will reboot during the process & that's perfectly normal.
* Now ur firmware would have been flashed successfully. If ur phone bootloops(showing bootanimation again'n'again) then goto RECOVERY MODE(Press & hold Home+Power keys) & select "wipe data/factory reset" & "wipe cache partition"(Use "Volume up/down" to navigate up/down & "Home button" to select & "Power button" to go back to previous menu). Then select "reboot system now".
*DONE!!
Ur phone would be 100% alright now.
Please follow the sequence exactly as mentioned. U will not find any other way than this one. Although Screenshots are messy...I'm on mobile rite now
Hope this helps...!!

Using window xp but while running through administrater it ask for password but I have never done something like that
Sent from my A13-MID using XDA Premium 4 mobile app

Enter ur login password :- The password that u use when the pc is turned/powered ON.
& if u don't know of such thing then ask it from the system administrator.

Can u plzzz tell me the procedure
Sent from my A13-MID using XDA Premium 4 mobile app

I guess u don't know. So, only thing u can do(if u use others' pc/laptop) is kindly request them to allow u admin rights. Tell them ur phone's life is hanging in the balance & only they can save it.
Btw procedure is simple...U just need to enter admin username(if asked) & password in the "Open As Admin" dialog box of Odin.:thumbup:
And if u have ur own pc then u shouldn't have faced this problem.

my big bro have an laptop and when it boot it doesnot need password but while using run as adminstrator it is asking for a password

the only need is to make this phone a portable router i am having 2 pices of fit