Related
I need help!!! i have unlock my boatloader then rooted and install CWM while using the CWM i have flash each and everything in my phone like, wipe factory data reset, dalvik cache, format sd card, format system etc and then i restart my phone its stuck on bootloader unlocked screen what should i do please help me! Even its not connecting to Mass storage so then i can place the ROM in SD Card please help !!!:crying:
You don't factory reset with custom recoveries like that, it's not a good idea. Put your phone in fastboot mode and then flash stock firmware from here. READ THOROUGHLY.
Which version of Phone and Android you were running on?
Haris Salam said:
I need help!!! i have unlock my boatloader then rooted and install CWM while using the CWM i have flash each and everything in my phone like, wipe factory data reset, dalvik cache, format sd card, format system etc and then i restart my phone its stuck on bootloader unlocked screen what should i do please help me! Even its not connecting to Mass storage so then i can place the ROM in SD Card please help !!!:crying:
Click to expand...
Click to collapse
Which version of Phone and Android you were running on?
Dont worry, you can reflash your ROM... Which model you are having?
padhu1989 said:
Dont worry, you can reflash your ROM... Which model you are having?
Click to expand...
Click to collapse
i have same problem too....
got stuck on bootloop after flash cm11 , spining forever
i have xt1032 single sim , 16 gb , global gsm
any advice for me....
thank you
kucingbaik2 said:
i have same problem too....
got stuck on bootloop after flash cm11 , spining forever
i have xt1032 single sim , 16 gb , global gsm
any advice for me....
thank you
Click to expand...
Click to collapse
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Moto G
deej_roamer said:
Which version of Phone and Android you were running on?
Click to expand...
Click to collapse
I was using 4.4.2 on Moto G Dual Sim, 16 GB.
padhu1989 said:
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Click to expand...
Click to collapse
thank you i will try it
lucky me, i was backup my original stock rom..., if i failed flash CM11 , i will restore my backup, and worked
---------- Post added at 10:56 AM ---------- Previous post was at 10:52 AM ----------
Haris Salam said:
I was using 4.4.2 on Moto G.
Click to expand...
Click to collapse
i have same version too...
You need to follow This guide!
Haris Salam said:
I was using 4.4.2 on Moto G Dual Sim, 16 GB.
Click to expand...
Click to collapse
You need to follow This guide! if your version is asian retail!
[Stock][Firmware Package][XT1033] Asia Retail - Alt. Link [4.4.2][Lock Bootloader]
Moto G
deej_roamer said:
You need to follow This guide! if your version is asian retail!
[Stock][Firmware Package][XT1033] Asia Retail - Alt. Link [4.4.2][Lock Bootloader]
Click to expand...
Click to collapse
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Moto G
Haris Salam said:
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Click to expand...
Click to collapse
If the phone version is Asian retial, so is it necessary to install the Asian firmware and rom? or we can install the Europe or US firmwares as well?
cause in Asian retail firmware there are some signal data loss issues. Please Advice.
Both
Haris Salam said:
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Click to expand...
Click to collapse
It is for both, guide has an option to lock bootloader if you want to, i guess which is useless for you.
So just skip 4.1 and 4.3 steps and you will be fine, or download Retail_AS.zip, your choice!
Moto G Dual Sim
padhu1989 said:
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Click to expand...
Click to collapse
I am going to follow these steps. If a found any sort of difficulty or problem will tell u thn. Thanks Friend!:good:
Installing
deej_roamer said:
It is for both, guide has an option to lock bootloader if you want to, i guess which is useless for you.
So just skip 4.1 and 4.3 steps and you will be fine, or download Retail_AS.zip, your choice!
Click to expand...
Click to collapse
Thanks for the support friend! im going to install this.
Haris Salam said:
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Click to expand...
Click to collapse
If you don't want to lock your boot loader, you need to skip 4.1 & 4.3 steps...
Sent from my XT1032 using XDA Premium 4 mobile app
You can install other local roms as well, US Global or GB will work fine for you
Haris Salam said:
If the phone version is Asian retial, so is it necessary to install the Asian firmware and rom? or we can install the Europe or US firmwares as well?
cause in Asian retail firmware there are some signal data loss issues. Please Advice.
Click to expand...
Click to collapse
You can install other local roms as well, US Global or GB will work fine for you
But the signal drop issues i am not sure are only related to asian firmware! it has something to with the bandwidth operation problem here!
Haris Salam said:
If the phone version is Asian retial, so is it necessary to install the Asian firmware and rom? or we can install the Europe or US firmwares as well?
cause in Asian retail firmware there are some signal data loss issues. Please Advice.
Click to expand...
Click to collapse
Goahead and flash GB version.. I'm using the GB version in xt1033 and I didn't face any issues so far.. Before flashing custom recovery, there is one recent system update 176.4.1 update which fixes signal issues.. ... Update it first and flash a custom recovery if you want and play with it
Sent from my XT1032 using XDA Premium 4 mobile app
How to get that update
padhu1989 said:
Goahead and flash GB version.. I'm using the GB version in xt1033 and I didn't face any issues so far.. Before flashing custom recovery, there is one recent system update 176.4.1 update which fixes signal issues.. ... Update it first and flash a custom recovery if you want and play with it
Sent from my XT1032 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
So how can i get that update which fixes signals issues. Can you tell me the procedure please.
Flash the GB version first... Reboot the phone.. You will get the update automatically... Or check it manually.. Settings- About phone - system update. Download it and install.. Once the update successfully installed.. Flash the custom recovery... Don't flash any custom recovery before installing G an update..
You need wifi I think to receive the update...
Sent from my XT1032 using XDA Premium 4 mobile app
padhu1989 said:
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Click to expand...
Click to collapse
thank you is work like charm
thank you
HI FRIENDS TODAY I AM GOING TO GIVE FULL AND EXPLAINED TUTORIAL TO UNBRICK ANY LG MODEL ( NOT SUPPORTED BY JTAG,OCTOPUS BOX)
PROBLEM INTRODUCTION
NO DOWNLOAD MODE
NO RECOVERY MODE
NO FASTBOOT MODE
FASTBOOT MODE
LG LOGO STUCK
PC DETECT AS QHSUSB BULK
PARTITION POP UP WHEN CONNECTED TO PC
SECURITY ERROR
KERNEL CRASH
NO SIGN OF LIFE
WHY MY PHONE BRICKED????????JUST FLASHING WRONG ROM ( MOST IN CASE OF REFURBISHED PHONE PURCHASED FROM THIRD PARTY SELLER)
FLASHING WRONG RECOVERY
FLASHING KERNEL
FLASHING KERNEL
DURING UPDATES ( FAILED OR INTERRUPTED)
AND MANY OTHER CAUSES
TOOLS REQUIREMENT LG FLASH TOOL FOR KDZ AND TOT FILE( http://forum.xda-developers.com/showthread.php?t=2432476(CREDIT GOES TO HYELTON)TOT OR KDZ FILE ( DEPENDING ON SITUATION) >>>>>>>>>>( KEEPING BOTH FILES RECOMMENDED)LG FIRMWARE EXTRACTOR ( http://forum.xda-developers.com/showthread.php?t=2600575) >>>>>>>>>>>> ( DOWNLOAD LATEST VERSION)
ANDROID SDK SLIM mod edit - malicious link removed) >>>>>>>>>>>> ( USEFULL TO UNBRICK PHONE IN FASTBOOT MODE)
QUALCOMM DRIVER ( http://www.mediafire.com/download/pba9wajnehr9qwg/Qualcomm+USB+Drivers.rar )>>>>>>>> ( for qhsusb bulk mode)
PDANET FOR ADB DRIVER ( http://pdanet.co/a/)
IF YOU FLASHED WRONG RECOVERY OR MODIFY PARTITION THEN YOU WILL STUCK IN FASTBOOT
SOLUTION FOR FASTBOOT
EXTRACT ANDROIDSDKSLIM.ZIP FILE ON DESKTOP ( ANY WHERE)
INSTALL PDANET AND CHOOSE LG COMPLETE INSTALLATION
DOWNLOAD PARTITION FILE FOR YOUR MODEL ( IF D802 THEN USE ONLY PARTITION FILE FOR D802) >>>>>>>>>> ( http://downloads.codefi.re/autoprime/LG/LG_G2)
NOTE : 1) YOU CAN EXTRACT PARTITION FILE FROM KDZ OR TOT FILE USING LGFIRMWARE EXTRACTOR TOOL
FOLLOW THIS VIDEO TO KNOW HOW TO EXTRACT PARTITION FILE
2) PARTITION FILE MUST BE IN .img FORMAT ( WHEN WE EXTRACT PARTITION FILE FROM KDZ OR TOT THEN IT IS IN .bin FORMAT SO SIMPLY RENAME FROM .bin to .img )
3) YOU NEED TO EXTRACT 10 FILES FROM TOT ( aboot, boot, sbl1, dbi, laf, recovery, modem, misc, rpm, tz ) and 9 FILES FROM KDZ ( misc file is not present in kdz so dont worry it is not important)
AFTER EXTRACTING PARTITION FILE AND RENAMING THEM YOU WILL GET 10 OR 9 FILE ( aboo.img, boot.img, laf.img, recovery.img, sbl1.img, dbi.img, rpm.img, tz.img, misc.img) and REMOVE ANY NUMBER FROM THE NAME OF FILES ( SUPPOSE YOU GET aboot_21345.bin THEN RENAME TO aboot.img)
NOW COPY THESE PARTITION FILE IN THE LAST FOLDER (PLATFORM-TOOLS) OF ANDROIDSDKSLIM FOLDER.
NOW CONNECT YOUR PHONE TO PC IN FASTBOOT MODE ( OPEN DEVICE MANAGER AND SEE ON THE TOP THERE WILL ANDROID ADB INTERFACE UNDER ANDROID PHONE. IF NOT THEN CHECK ADB DRIVER INSTALLED PROPERLY OR NOT.
NOW GO TO THE THE FOLDER PLATFORM -TOOL INSIDE ANDROIDSDKSLIM FOLDER.
NOW PRESS AND HOLD SHIFT BUTTON ON KEYBOARD AND RIGHT CLICK IN THAT FOLDER AND YOU WILL GET AN OPTION OPEN COMMAND PROMPT OR WINDOW HERE. CLICK ON IT AND YOU WILL GET CMD WINDOW.
NOW TYPE fastboot devices ( IT WILL SHOW YOUR DEVICES )
NOW TYPE THESE COMMAND
fastboot erase recovery
fastboot erase laf
fastboot flash laf laf.img
fastboot reboot
exitNOW REMOVE USB CABLE AND SWITCH OFF YOUR PHONE BT LONG PRESSING POWER BUTTON
NOW PRESS AND HOLD VOL UP AND CONNECT TO PC AND YOU WILL GET DOWNLOAD MODE FIXED
HURREYYYYYYYYYYYYYY
GO AND FLASH STOCK ROM ( http://forum.xda-developers.com/showthread.php?t=2432476)
IF YOU STILL STUCK IN FASTBOOT MODE THEN TYPE THESE COMMAND ( erase all 10 or 9 file and flash them one by one as shown)
fastboot erase aboot ( this command will erase aboot.img from phone)
fastboot flash aboot aboot.img ( this command will flash aboot to phone )
fastboot erase boot
fastboot flash boot boot.img
fastboot erase laf
fastboot flash laf laf.img
fastboot erase rpm
fastboot flash rpm rpm.img
fastboot erase recovery
fastboot flash recovery recovery.img
fastboot erase modem
fastboot flash modem modem.img
fastboot erase misc
fastboot flash misc misc.img
fastboot erase sbl1
fastboot flash sbl1 sbl1.img
fastboot erase tz
fastboot flash tz tz.img
fastboot erase dbi
fastboot flash dbi dbi.img
fastboot reboot
exitNOW REMOVE USB CABLE AND SWITCH OFF YOUR PHONE BT LONG PRESSING POWER BUTTON
NOW PRESS AND HOLD VOL UP AND CONNECT TO PC AND YOU WILL GET DOWNLOAD MODE FIXED
HURREYYYYYYYYYYYYYY
GO AND FLASH STOCK ROM ( http://forum.xda-developers.com/showthread.php?t=2432476)
SOLUTION FOR ALL THE PROBLEM WITH NO DOWNLOAD MODEYOU NEED TO FORCE PHONE INTO QHSUSB BULK MODE BY SHORTING TEST POINT
WHEN YOU GET QHSUSB BULK MODE IN DEVICE MANAGER THEN INSTALL QUALCOMM DRIVER ( http://www.mediafire.com/download/pba9wajnehr9qwg/Qualcomm+USB+Drivers.rar)
NOTE : THERE ARE TWO MODE IN QHSUSB BULK
1) QUALCOMM HS-USB 9006
THIS MODE IS VERY EASY TO FIX. YOU NEED THE PARTITION FILE THAT WE GET IN THE STARTING TO SOLVE FASTBOOT MODE)
TO SOLVE 9006 FOLLOW THIS METHOD ( http://forum.xda-developers.com/showthread.php?t=2582142 )
UBUNTU METHOD IS UNIVERSAL IT CAN BE USED FOR ANY PHONE IN 9006 ( UNBRICK VERY PARTITION METHOD ( http://forum.xda-developers.com/lg-g2/general/unbrick-lg-g2-qhsusbbulkqualcomm-9006-t2939627) BY TUNG KICK IS ONLY FOR G2 HOWEVER IT CAN BE USED FOR GPRO2 AND G FLEX BUT I M NOT SURE IT MAY NOT WORK OR BRICKED MORE)
WHEN YOUR PHONE GET STUCK IN 9006 THEN LOTS OFF DRIVE POP UP WHEN CONNECTED TO PC ( MOST IMPORTANT IDENTIFICATION)
2 ) QUALCOMM HS-USB 9008
IF YOU STUCK IN 9008 THEN THIS IS THE SUPER HARD BRICK MODE.
CONTACT aftabalam8c2 ( http://forum.xda-developers.com/member.php?u=4554553 ) this guy not only can unbrick lg g2 , g3 but g pro 2, g flex, vu3, vu2, nexus4 , nexus 5, lg g , lg gpro, and around MORE THAN 30 ( I DONT KNOW BUT HE TOLD ME ALL HE CAN UNBRICK MORE THAN 50 ) devices of lg which not supported by JTAG OR OCTOPUS BOX.
ACCORDING TO HIM MOST USER DAMAGED DURING SHORTING OF TEST POINT ( SO BETTER TO ASK HIM BEFOR SHORT)
I NEVER SHORTED SO DONT ASK ME. HE ALSO MADE A SERIES OF TEST POINT ON YOU TUBE FOR MANY DEVICES BUT THESE VIDEO ARE NOT PUBLIC NOW. MAY BE HE MAKE ALL VIDEOS PRIVATE AFTER SOME GUY CHEATED HIM ON XDA ( CONCLUDED FROM HIS COMMENTS)
AND THE ACCOUNT OF THIS GUY DISABLED BY XDA FOR 1 WEEK ( I ASKED HIM PERSONALY ON WHATS APP)
SO IF YOU WANT THE TEST POINT FOR ANY PHONE ASK HIM.
THIS GUY UNBRICKED MY LG G FLEX IN 20 MINUTES IN FRONT OF ME ( WE ARE FROM SAME STATE SO I WENT HIS HOME)
FO THE FULL STORY OF LG G FLEX UNBRICKING SEE THIS ( http://forum.xda-developers.com/lg-...nload-mode-t3059257/post59555140#post59555140)
SO THE MOST IMPORTANT THING IS TO SHORT THE TEST POINT CORRECTLY WITHOUT DAMAGING EMMC ( I WOULD ADVICE ALL OF YOU PLEASE ASK HIM BEFOR SHORTING MAY HE SHARE THOSE VIDEOS ON YOU TUBE )
FOR COLLECTION OF TEST POINT SEE THIS ( http://forum.xda-developers.com/hardware-hacking/hardware/collection-test-phone-t3048736 )
SOLUTION FOR ERROR DURING FLASHINGFOLLOW THIS GUIDE ( http://forum.xda-developers.com/lg-g2/general/lg-g2-cross-dll-device-model-fota-laf-t3003717 )
THERE ARE MANY GUYS WHO CLAIM TO FIX YOUR BRICKED LG PHONE BUT I DONT KNOW THE AUTHENTICITY OF THESE GUYS
TUNGKICK WHICH IS ALSO WHO UNBRICK HAS VERY BAD RECORD, I SEEN THE POST MANY GUYS CLAIM THAT HE STEAL PASSWORD AND DATA FROM THEIR PC AND TOOL HE USED INSTALL KEYLOGGER TO YOUR PC ( I AM JUST TELLING THE COMMENTS ON GUYS AND THEY ALSO UPLOADED SOME PIC FOR THE PROOF)
THANKS SO MUCH
THREAD UNDER CONSTURCTION ( I WILL UPDATE PICTURE FOR MORE DETAILS )
to be continue..........
Hi Guys, pls help me.
This is not the first time i tried to update firmware using KDZUpdater [KDZ_FW_UPD.exe] .
But this is the first time my device has been bricked.
During updating my firmware, i was in "Emergency Mode" and i received some error on KDZUpdater GUI Console.
As i was unable to move from "Emergeny Mode", i tried again to update firmware, but again i got some error.
I thought removing the battery will do some good, but i was wrong.
Now my mobile is as good as "BLACK BRICK".
It even doesn't detect in "Device Manager".
Note:
Before using "KDZUpdater", i had disabled "LG modems" from device manager.
Pls help me on this.
Sent from my TCL J636D+ using XDA Free mobile app
vcforums said:
Hi Guys, pls help me.
This is not the first time i tried to update firmware using KDZUpdater [KDZ_FW_UPD.exe] .
But this is the first time my device has been bricked.
During updating my firmware, i was in "Emergency Mode" and i received some error on KDZUpdater GUI Console.
As i was unable to move from "Emergeny Mode", i tried again to update firmware, but again i got some error.
I thought removing the battery will do some good, but i was wrong.
Now my mobile is as good as "BLACK BRICK".
It even doesn't detect in "Device Manager".
Note:
Before using "KDZUpdater", i had disabled "LG modems" from device manager.
Pls help me on this.
Sent from my TCL J636D+ using XDA Free mobile app
Click to expand...
Click to collapse
You have only one option.
You need to force your phone into qhsusb bulk mode by shorting test point.
What does that mean??
Will this be done through software or I need some special hardware or should I sent to LG service centre.
Pls guide
Sent from my TCL J636D+ using XDA Free mobile app
vcforums said:
What does that mean??
Will this be done through software or I need some special hardware or should I sent to LG service centre.
Pls guide
Sent from my TCL J636D+ using XDA Free mobile app
Click to expand...
Click to collapse
You need to open your phone and do short of some pins.
A guys named aftabalam8c2 has full tutorial video how to do this.
And he will help u.
I m posting his contact details in pm
I have no download mode, but rom still works fine. cant root and cant start into recovery.
I solved the QHUSB 9006 Method in ubuntu, but after filling the partitions, all is like before, still NO download mode.....
Lg g3 f460s no download mode nor flashboot
I have lg g3 prime.
Lg g3 f460s from koria, sk telecom.
I want to install a custom rom, but it failed and i havent kept backup of stock rom, so first it shows " secure boot error" then i again go to fastboot mode and by mistake flash wrong file at boot partition & recovery partition.
After that when i switch on my phone it shows secure boot error & after it 's switched off.
When i press vol+ and insert in usb , download mode dialog comes and after 5 to 6 seconds it switch off automatically.
Not any key combination work for recovery mode & fastboot mode.
Means my phone have not download mode and not fastboot mode.
Now what should i do for unbrick it.
Don't support with lg l65 D280g?
friend you help me with D280g lg? help me pliz
I have the g pro 2 with no download mode just lg logo what should I do?
---------- Post added at 05:30 PM ---------- Previous post was at 05:28 PM ----------
SANJAYTHL said:
I have lg g3 prime.
Lg g3 f460s from koria, sk telecom.
I want to install a custom rom, but it failed and i havent kept backup of stock rom, so first it shows " secure boot error" then i again go to fastboot mode and by mistake flash wrong file at boot partition & recovery partition.
After that when i switch on my phone it shows secure boot error & after it 's switched off.
When i press vol+ and insert in usb , download mode dialog comes and after 5 to 6 seconds it switch off automatically.
Not any key combination work for recovery mode & fastboot mode.
Means my phone have not download mode and not fastboot mode.
Now what should i do for unbrick it.
Click to expand...
Click to collapse
Same here..have you found a fix yet?
daredavel said:
---------- Post added at 05:30 PM ---------- Previous post was at 05:28 PM ----------
Same here..have you found a fix yet?
Click to expand...
Click to collapse
got the solution but can't find the apropriate files, i am showing the method, if you find the files let me know.
1. with willcracker board diag,
in that case you need chipset file for apq8084 (snapdragon 805), i have searched to many but cant find. in that case you need original (latest on your phone) firmware in .tot file and convert it in .mbn file. this you can do in willcracker. only the problem is apq8084 chipset files and latest firmware in tot file. you can find it in .kdz but cant get it in .tot file.
2. with qpst programme. (qfil programe)
in this method you need programmer file, rawprogram.xml & patch.xml of the same version phone (f460s) and yes original firmware.
you can find both program on google or xda.
if you got the appropriate files let me know and share with me.
thanks in advance.
Help
Cannot unbrick ls996 in q-bulk mode. tried everything...every site. Even tried to contact member mentioned in post. Im willing to work hard to unbrick, NOT looking for easy way...out...but im no phone technican by all means. Thanks!!!
I've got a E975 (Optimus G Intl) to unbrick here.
I've got it to fastboot mode, but I can't get the laf.img and dbi.img files (they are not in the .kdz or .dz files).
Can anyone give me a help?
Wrong ROM install in LG f460s
SANJAYTHL said:
got the solution but can't find the apropriate files, i am showing the method, if you find the files let me know.
1. with willcracker board diag,
in that case you need chipset file for apq8084 (snapdragon 805), i have searched to many but cant find. in that case you need original (latest on your phone) firmware in .tot file and convert it in .mbn file. this you can do in willcracker. only the problem is apq8084 chipset files and latest firmware in tot file. you can find it in .kdz but cant get it in .tot file.
2. with qpst programme. (qfil programe)
in this method you need programmer file, rawprogram.xml & patch.xml of the same version phone (f460s) and yes original firmware.
you can find both program on google or xda.
if you got the appropriate files let me know and share with me.
thanks in advance.
Click to expand...
Click to collapse
I have same issue wrong ROM installed on LG f460s and I have no download mode, no recovery, no fastboot no charging shown, no sign of life, just Qualcomm HS-USB QDLoad 9008 is shown in device manager when connect to PC.. I am searching APQ8084 folder to paste in boarddiag tool, Dear if you have found any other way to solve this issue please let me know. thanx in advance
power outage while flashing kdz on LG C660
Please help... I know my phone is a little outdated but I would still love use it for my daily routine . I'm in the middle of flashing the original firmware when the power outage happened. Now it won't power on at all. Been searching for days on what pins/components to short to force it into qhsusb bulk mode but no luck. I hope someone can help me...:crying:
tobitab said:
Please help... I know my phone is a little outdated but I would still love use it for my daily routine . I'm in the middle of flashing the original firmware when the power outage happened. Now it won't power on at all. Been searching for days on what pins/components to short to force it into qhsusb bulk mode but no luck. I hope someone can help me...:crying:
Click to expand...
Click to collapse
Which phone??
Anyone there" help me" i hav bricked my lg g2 f320k" wenever i connect my phone to pc" lots of partitions comes up
superguy19 said:
Which phone??
Click to expand...
Click to collapse
My phone is LG Optimus Pro C660...
---------- Post added at 01:32 PM ---------- Previous post was at 01:18 PM ----------
superguy19 said:
Which phone??
Click to expand...
Click to collapse
Ajayz said:
Anyone there" help me" i hav bricked my lg g2 f320k" wenever i connect my phone to pc" lots of partitions comes up
Click to expand...
Click to collapse
Have you tried checking on the 'Device Manager' what mode is the phone in 'Ports' section when connected to pc?
After that there are instructions in the first page for every mode. My phone doesn't show up and I needed it to force into
qhsusb bulk mode in order to proceed...
Bricked LG H440n
Hello guys I have bricked my LG H440n in an attempt of unlocking the bootloader. My phone doesn't get recognised by pc, I can only enter fastboot mode, but command like "fastboot erase aboot" are not working, it just says remote: "unknown command". Can anyone help me where can I find the pins to short on this phone?
Hello!
I would like to ask some help with my hard bricked G3 D855 16GB, i installed wrong rom
My english is not a best, and i dont dare to do anything. I have win 8.1. I dont know about Linux, and virtual PC.
I will very glad that someone can help me maybe via teamviewer. I also donate You. Please
If you think that You can help me maybe, please write me.
I have an LG G Stylo with Cricket and tried to flash twrp onto it but they don't have a stylo version yet, so I found an unofficial version and now it's stuck in a [Secure Booting Error] loop. I have tried to flash a kdz onto it but there isn't one for the cricket version. ( at least from what I've seen ) What do I do?
I've gotten the open source kdz but I don't know how to compile whatsoever and the customer support is no help. I really need this phone for work, please help.
There is no Cricket KDZ but there is TOT that unbricks. From Mega http://forum.xda-developers.com/showpost.php?p=66949501&postcount=12 or torrent http://forum.xda-developers.com/lg-g-stylo/how-to/stock-firmware-tot-dll-cricket-lg-g-t3376113
Flagmax said:
There is no Cricket KDZ but there is TOT that unbricks. From Mega http://forum.xda-developers.com/showpost.php?p=66949501&postcount=12 or torrent http://forum.xda-developers.com/lg-g-stylo/how-to/stock-firmware-tot-dll-cricket-lg-g-t3376113
Click to expand...
Click to collapse
Excuse my noobieness but, what is a TOT and how do i use it?
Download: LG Flash tool 1.8
https://mega.nz/#!xwokFToa!vqe2Uqta25TLRXne6Yu342-uWMdLSE5hNiVu-cPqxBY
and this megalock.dll
http://forum.xda-developers.com/attachment.php?attachmentid=2258189&d=1379209014
Install the LG FLASH tool to c:\lg\flashtool. do not run it
Copy the above megalock.dll into c:\lg\flash\
run LG Flash tool
Follow this guide: http://forum.xda-developers.com/showpost.php?p=64624324&postcount=2 to flash tot file.
matt0159 said:
I have an LG G Stylo with Cricket and tried to flash twrp onto it but they don't have a stylo version yet, so I found an unofficial version and now it's stuck in a [Secure Booting Error] loop. I have tried to flash a kdz onto it but there isn't one for the cricket version. ( at least from what I've seen ) What do I do?
I've gotten the open source kdz but I don't know how to compile whatsoever and the customer support is no help. I really need this phone for work, please help.
Click to expand...
Click to collapse
THIS SHOULD HELP
HardReset.info:
Factory Mode LG Stylo 5
How to enter factory mode on LG Stylo 5? How to open factory mode in LG Stylo 5? How to get access to factory mode in LG Stylo 5? How to use factory mode on LG Stylo 5?
If you would like test the hidden feature of LG Stylo 5 you should enter Factory Mode. Here you can test the hardware features of Android 9.0 Pie.
At first switch off the smartphone by pressing the Power button for a couple of seconds.Hard Reset LG Stylo 5
Then hold down Volume Down and Power keys for a few seconds.HardReset LG Stylo 5
When the LG logo pops up let go of the Power button, push Volume Down and hold down the Power key once more.
When Factory Mode appears let go of all buttons.Factory data reset LG Stylo 5
Great! Your phone will be in Factory Mode.
Use Volume buttons to scroll down nad the Power key to confirm that.
---------- Post added at 07:00 AM ---------- Previous post was at 06:52 AM ----------
gene10 said:
Download: LG Flash tool 1.8
https://mega.nz/#!xwokFToa!vqe2Uqta25TLRXne6Yu342-uWMdLSE5hNiVu-cPqxBY
and this megalock.dll
http://forum.xda-developers.com/attachment.php?attachmentid=2258189&d=1379209014
Install the LG FLASH tool to c:\lg\flashtool. do not run it
Copy the above megalock.dll into c:\lg\flash\
run LG Flash tool
Follow this guide: http://forum.xda-developers.com/showpost.php?p=64624324&postcount=2 to flash tot file.
Click to expand...
Click to collapse
Any help on LG stylo 5 LMQ720 I would like the T-Mobile ROM to flash. Also the command adb reboot bootloader doesn't work it just restarts phone back to normail and power off then phone cable in computer then hold down vol key then plug in cable to phone until fastboot it doest show up.
Thank you for any help
---------- Post added at 07:17 AM ---------- Previous post was at 07:00 AM ----------
gene10 said:
Download: LG Flash tool 1.8
https://mega.nz/#!xwokFToa!vqe2Uqta25TLRXne6Yu342-uWMdLSE5hNiVu-cPqxBY
and this megalock.dll
http://forum.xda-developers.com/attachment.php?attachmentid=2258189&d=1379209014
Install the LG FLASH tool to c:\lg\flashtool. do not run it
Copy the above megalock.dll into c:\lg\flash\
run LG Flash tool
Follow this guide: http://forum.xda-developers.com/showpost.php?p=64624324&postcount=2 to flash tot file.
Click to expand...
Click to collapse
Any help on LG stylo 5 LMQ720 I would like the T-Mobile ROM to flash. Also the command adb reboot bootloader doesn't work it just restarts phone back to normail and power off then phone cable in computer then hold down vol key then plug in cable to phone until fastboot it doest show up.
Thank you for any help
Flagmax said:
No hay Cricket KDZ, pero hay TOT que se deshace. Desde Mega http://forum.xda-developers.com/showpost.php?p=66949501&postcount=12 o torrent http://forum.xda-developers.com/lg-g-stylo/how-to/stock-firmware -tot-dll-cricket-lg-g-t3376113
Click to expand...
Click to collapse
mis para lg q720cs?
Hello everyone,
I'm actually in front of a big problem. I try this night to upgrade from FRD-L09C432B120 to FRD-L09C432B316. Since I try it, my phone stay on a Warning screen and i can't do anything. (Just try to shut down by a long press on power button and it make a reboot and it's the same for every key combination).
I can't go in Recovery or eRecovery. The only things that works is the fastboot mode. I try to flash the stock firmware after an extract of "UPDATE.APP" but the system image give me an error. I also try to put UPDATE.APP on the SD Card but I can't access to the update mode (by press vol+ , vol- and power button). I think that i've try all the ideas that i've fund on internet !
I've no more ideas. Do you think that is possible to unbrick it ?
Thanks to your help and your reply.
Flo.B said:
Hello everyone,
I'm actually in front of a big problem. I try this night to upgrade from FRD-L09C432B120 to FRD-L09C432B316. Since I try it, my phone stay on a Warning screen and i can't do anything. (Just try to shut down by a long press on power button and it make a reboot and it's the same for every key combination).
I can't go in Recovery or eRecovery. The only things that works is the fastboot mode. I try to flash the stock firmware after an extract of "UPDATE.APP" but the system image give me an error. I also try to put UPDATE.APP on the SD Card but I can't access to the update mode (by press vol+ , vol- and power button). I think that i've try all the ideas that i've fund on internet !
I've no more ideas. Do you think that is possible to unbrick it ?
Thanks to your help and your reply.
Click to expand...
Click to collapse
But please confirm , was the update from b120 to b316 successfull?
Sent from my KIW-L22 using Tapatalk
gopinaidu77 said:
But please confirm , was the update from b120 to b316 successfull?
Click to expand...
Click to collapse
I think it failed because the warning screen showed right?
Sent from my honor 5X using XDA Labs
adriansticoid said:
I think it failed because the warning screen showed right?
Click to expand...
Click to collapse
Right that was what I am also thinking bro.
---------- Post added at 01:35 PM ---------- Previous post was at 01:35 PM ----------
adriansticoid said:
I think it failed because the warning screen showed right?
Sent from my honor 5X using XDA Labs
Click to expand...
Click to collapse
So it's a failure . which mean that it is a semi flashed update . which doesn't installed update.app .
Extract update.app from ota and put it in dload folder .later flash it manually using dload method .
He should follow this way to overcome those reboots
Sent from my KIW-L22 using Tapatalk
---------- Post added at 01:36 PM ---------- Previous post was at 01:35 PM ----------
Flo.B said:
Hello everyone,
I'm actually in front of a big problem. I try this night to upgrade from FRD-L09C432B120 to FRD-L09C432B316. Since I try it, my phone stay on a Warning screen and i can't do anything. (Just try to shut down by a long press on power button and it make a reboot and it's the same for every key combination).
I can't go in Recovery or eRecovery. The only things that works is the fastboot mode. I try to flash the stock firmware after an extract of "UPDATE.APP" but the system image give me an error. I also try to put UPDATE.APP on the SD Card but I can't access to the update mode (by press vol+ , vol- and power button). I think that i've try all the ideas that i've fund on internet !
I've no more ideas. Do you think that is possible to unbrick it ?
Thanks to your help and your reply.
Click to expand...
Click to collapse
Consider reading my above post bro.
Sent from my KIW-L22 using Tapatalk
HONOR 8 Bricked
Hello ,
It happened on my FRD-L04, but I think is the same.
Bootloader is unlocked ?
1. Do you have all drivers installed ? OK
2.Do you have STOCK ROM ? OK. If not, use Huawei Firmare Finder to find suitable ROM. Be aware what you choose !!!
3. Unzipp (WinRar) the ROM.
4.Download and install Huawei Update Extractor. Run Huawei Update Extractor . Choose Update.app from the folder you unzipped the ROM.
5. Select cust.img , boot.img , recovery.img and system.img and extract them on a folder.
6.. Install MultiTool by Team (Multi Tool Team). The instalation will make a folder named UNBRICK.
7. Move the files extracted : cust.img , boot.img , recovery.img and system.img on the folder UNBRICK
8. Run MultiTool . Choose option 6 (unbrick) and after that choose option 2 ( if you already have files on folder UNBRICK)
9. Let the tool finish the job.
NOTE : You must have all drivers installed and the phone in FASTBOOT mode ( turn phone OFF - Press VOL- and insert USB cable simultaneously.)
Good luck !
Hi, thanks everyone for your reply.
Unfortunatly, the dload method seems not work. I think that to run this method, i need to press simultaneously vol+, vol- and the power button to run it, right ?
If it's like that, the method doesn't work anymore.
I will try the process given by technoguy09 and I said to you if it's ok !
So, after many try, every method that i try doesn't work.
Even the Unbrick method doesn't work because the system and cust report an error.
For the cust, i have "partition error" and for the system I have the "sparse flash write failure". Can we correct this error ?
Flo.B said:
So, after many try, every method that i try doesn't work.
Even the Unbrick method doesn't work because the system and cust report an error.
For the cust, i have "partition error" and for the system I have the "sparse flash write failure". Can we correct this error ?
Click to expand...
Click to collapse
Was the bootloader unlocked ?
Do u have twrp installed ?
Sent from my KIW-L22 using Tapatalk
---------- Post added at 03:53 PM ---------- Previous post was at 03:53 PM ----------
Flo.B said:
Hi, thanks everyone for your reply.
Unfortunatly, the dload method seems not work. I think that to run this method, i need to press simultaneously vol+, vol- and the power button to run it, right ?
If it's like that, the method doesn't work anymore.
I will try the process given by technoguy09 and I said to you if it's ok !
Click to expand...
Click to collapse
If u have twrp I will make a flashable zip of stock ROM and cust
Sent from my KIW-L22 using Tapatalk
The bootloader is unlock and TWRP was install but now I can't access it. I try to restore stock recovery and it's the same result.
Flo.B said:
The bootloader is unlock and TWRP was install but now I can't access it. I try to restore stock recovery and it's the same result.
Click to expand...
Click to collapse
Can fastboot detect your phone?
Yes, fastboot is detect, I can launch some command (fastboot devices display my phone, flash etc) everything work but flash recovery didn't change anything and flash system response an error (sparse flash write failure).
Flo.B said:
Yes, fastboot is detect, I can launch some command (fastboot devices display my phone, flash etc) everything work but flash recovery didn't change anything and flash system response an error (sparse flash write failure).
Click to expand...
Click to collapse
From what you said, looks like it is reallt bricked. Service center is your friend.
I think too... I hope that there will be no problem with service center because of the phone is unclocked !
I was never had this kind of problem with my previous android phone. I'm really bad ^^
Thanks for all everybody.
Flo.B said:
So, after many try, every method that i try doesn't work.
Even the Unbrick method doesn't work because the system and cust report an error.
For the cust, i have "partition error" and for the system I have the "sparse flash write failure". Can we correct this error ?
Click to expand...
Click to collapse
Try another ROM.
Flo.B said:
I think too... I hope that there will be no problem with service center because of the phone is unclocked !
I was never had this kind of problem with my previous android phone. I'm really bad ^^
Thanks for all everybody.
Click to expand...
Click to collapse
Goodluck with it buddy.
technoguy09 said:
Try another ROM.
Click to expand...
Click to collapse
I try at least 3 ROM download on different website. I don't think that it can change anything.
I had the same problem.
Dont worry, Honor 8 phones are nearly unbrickable.
Take your B120 ROM extract recovery, cust and boot partitions. (use huawei update extractor)
Flash Them via fastboot (adb) then force the dload method via the 3 buttons combo.
I had all the problems you described and restored my phone as new. (even the "sparse flash write failure" error)
Now i'm on EMUI 5 rooted, no problem
---------- Post added at 06:30 PM ---------- Previous post was at 06:25 PM ----------
Please refer this thread as it might help you.
http://forum.xda-developers.com/mate-8/general/fuss-debrick-restore-mate-8-t3457969
Have a little faith in your Honor
Flo.B said:
I try at least 3 ROM download on different website. I don't think that it can change anything.
Click to expand...
Click to collapse
Did you use Huawei Firmare Finder for your model ?
morpheus302 said:
I had the same problem.
Dont worry, Honor 8 phones are nearly unbrickable.
Take your B120 ROM extract recovery, cust and boot partitions. (use huawei update extractor)
Flash Them via fastboot (adb) then force the dload method via the 3 buttons combo.
I had all the problems you described and restored my phone as new. (even the "sparse flash write failure" error)
Now i'm on EMUI 5 rooted, no problem
---------- Post added at 06:30 PM ---------- Previous post was at 06:25 PM ----------
Please refer this thread as it might help you.
http://forum.xda-developers.com/mate-8/general/fuss-debrick-restore-mate-8-t3457969
Have a little faith in your Honor
Click to expand...
Click to collapse
I have extract all this img but the flash of cust won't work too so, the dload method can't be launch. Now, I send my phone to the service center yesterday. Wait and See ^^
technoguy09 said:
Did you use Huawei Firmare Finder for your model ?
Click to expand...
Click to collapse
Yes, I Download 2 ROM on it but same problem on both.
Flo.B said:
I have extract all this img but the flash of cust won't work too so, the dload method can't be launch. Now, I send my phone to the service center yesterday. Wait and See ^^
Yes, I Download 2 ROM on it but same problem on both.
Click to expand...
Click to collapse
Leave it for service centre people .they will take care
Sent from my KIW-L22 using Tapatalk
Code:
[CENTER]If You Have Hard Bricked Your Device Then Only Use This Guide[/CENTER]
CPH1861EX_11.A.29
Files You Need To Download:
1:Miracle Box Tool-https://mega.nz/#!lVsQGSaC!6TTJopMyntMQA0IKYdC_5BlsxIjV_Ibhx2qWL_ZqDyI
2:Stock Rom- https://mega.nz/#F!ncMFUaaa!0fVNwJ_Io0EMFv8YLjBZlQ [Select Download As Zip]
3:https://androidmtk.com/install-android-cdc-driver-manually [Install Drivers Using This Guide]
Click to expand...
Click to collapse
Steps To Flash Stock Rom:
1:Install Miracle Box And Drivers
2:Launch Miracle Box
3: Open Mtk Tab
4:Click on Services
5:Select Write From The Available Options
6:Select 8th Boot From Boot Options
7:In Second Options,Select Oppo Realme 1
8:Check Skip Preloader File
9:Hit Start
10:Now connect your phone and hold volume and power buttons... It will flash and turn off your phone
11:Remove Cable And Press Power+VOLUME Up For 15 Seconds
You Have Unbricked Your Device
Click to expand...
Click to collapse
Credits:
Hamza(From Telegram Group For Writing The Tutorial0
Shobith(For Stock Rom Dump)
AnuragRai(For Simplifying The Guide)
1st link miracle box is not working plz correct it bro
can you share download links from other providers? mega asks for premium account.
thank you.
Didn't work for me
anurag rai said:
Code:
[CENTER]If You Have Hard Bricked Your Device Then Only Use This Guide[/CENTER]
CPH1861EX_11.A.29
Credits:
Hamza(From Telegram Group For Writing The Tutorial0
Shobith(For Stock Rom Dump)
AnuragRai(For Simplifying The Guide)
Click to expand...
Click to collapse
After flashing twrp recovery when I booted my device, a software update popped up and it automatically updated over night and my device hard bricked. I tried everything but couldn't fix it. My pc is not even recognising my phone so can't follow your steps. Any suggestion or help to fix my device will be appreciated.
same mine bro,
rom version was a31 and after installed twrp, my device hard bricked. i couldnt solve yet, waiting a newer version of miracle box or etc.
anurag rai said:
Code:
[CENTER]If You Have Hard Bricked Your Device Then Only Use This Guide[/CENTER]
CPH1861EX_11.A.29
Credits:
Hamza(From Telegram Group For Writing The Tutorial0
Shobith(For Stock Rom Dump)
AnuragRai(For Simplifying The Guide)
Click to expand...
Click to collapse
i dumped the stock rom bro @besttipsYT Not Shobith
this method is not working at this time...when i trying to flash by this method only show.......phone connected......downloding boot8....then disconnect my phone ..&reboot
Please don't flash custom recovery (here twrp) without proper knowledge or just sake of modding device. The builds and methods are not always working and may end up bricking your device.
Hi There, Can someone PLZ help me setting up OPPO PRELOADER Drivers correctly. Everytime i try to use miracle thunder i get the following log:
Waiting for USB Port...
Set USB Serial Device (COM9)
Connecting to Phone,Wait..
Connected to Phone.
CPU: MT6771 SW:0000 Ver: CA00
>>Downloading Boot8 ...
and it remains on here forever.
Actually oppo preloader shows for some time in pc and after that it goes away and hence it is not letting the miracle thunder work properly (i guess)
when my phone was working (booting in coloros 6, then also oppo preloader was doing the same thing and after a few seconds my battery would start charging), now i can't see anything on screen as it's bricked now.
Preloader doesn't even work with SP Flash Tools also.
EDIT : I have tried almost everything i knew, drivers manager add legacy option etc.
If someone could help me get out of this problem, i would really be grateful.
Brick Reason : Flashed TWRP but used fastboot command to boot into that : (
PLEASE HELP SOMEONE
Alen012 said:
Hi There, Can someone PLZ help me setting up OPPO PRELOADER Drivers correctly. Everytime i try to use miracle thunder i get the following log:
Waiting for USB Port...
Set USB Serial Device (COM9)
Connecting to Phone,Wait..
Connected to Phone.
CPU: MT6771 SW:0000 Ver: CA00
>>Downloading Boot8 ...
and it remains on here forever.
Actually oppo preloader shows for some time in pc and after that it goes away and hence it is not letting the miracle thunder work properly (i guess)
when my phone was working (booting in coloros 6, then also oppo preloader was doing the same thing and after a few seconds my battery would start charging), now i can't see anything on screen as it's bricked now.
Preloader doesn't even work with SP Flash Tools also.
EDIT : I have tried almost everything i knew, drivers manager add legacy option etc.
If someone could help me get out of this problem, i would really be grateful.
Brick Reason : Flashed TWRP but used fastboot command to boot into that : (
PLEASE HELP SOMEONE
Click to expand...
Click to collapse
Miracle box, SP Flash Tool and MTK Droid Tools no longer work with Realme. If you can access Fastboot then flash stock recovery and proceed further.
Bootloop if i try t access fastboot mode. Can go to recovery but its not allowing me to flash amything saying its an older version. Any work around yet?
Naveen56 said:
Miracle box, SP Flash Tool and MTK Droid Tools no longer work with Realme. If you can access Fastboot then flash stock recovery and proceed further.
Click to expand...
Click to collapse
StripsOfTatti said:
Bootloop if i try t access fastboot mode. Can go to recovery but its not allowing me to flash amything saying its an older version. Any work around yet?
Click to expand...
Click to collapse
Which recovery are you in? Is it Stock or Custom?
If u have stock first wipe data and then flash boot.img or ozip file (stock ROM).
If u have custom recovery then you need to flash stock recovery + stock ROM.
plz help me ihave realme 1 and it stuck in logo and orange state and restart over and over and icannot boot into recovery or fastboot plz help me
Simba Gaara said:
plz help me ihave realme 1 and it stuck in logo and orange state and restart over and over and icannot boot into recovery or fastboot plz help me
Click to expand...
Click to collapse
If recovery and fastboot are inaccessible means you need to visit service center.
When trying to connect realme 1 to miracle it showing usb device not connected, how to solve this? Drivers are installed
Naveen56 said:
Miracle box, SP Flash Tool and MTK Droid Tools no longer work with Realme. If you can access Fastboot then flash stock recovery and proceed further.
Click to expand...
Click to collapse
So bro in case if I brick my phone then I can flash stock rom using stock recovery.......??
Do I get those Rom files from official realme website?
AwesomeVk47 said:
So bro in case if I brick my phone then I can flash stock rom using stock recovery.......??
Do I get those Rom files from official realme website?
Click to expand...
Click to collapse
Yes. Do remember you need both fastboot and recovery to be working, so you can flash Stock Recovery (only if you have TWRP installed).
If you have stock recovery installed then download stock rom from official Realme site and place it in the Sdcard (otg wont help). Enter into recovery and update/install the ozip.
If your phone is completely dead then above method wont help and you have to follow another one.
Note: If your device is rooted then installing (from stock recovery) stock rom fails. At this time flash TWRP from fastboot then flash zip file (convert stock rom from ozip to zip).
Naveen56 said:
Yes. Do remember you need both fastboot and recovery to be working, so you can flash Stock Recovery (only if you have TWRP installed).
If you have stock recovery installed then download stock rom from official Realme site and place it in the Sdcard (otg wont help). Enter into recovery and update/install the ozip.
If your phone is completely dead then above method wont help and you have to follow another one.
Note: If your device is rooted then installing (from stock recovery) stock rom fails. At this time flash TWRP from fastboot then flash zip file (convert stock rom from ozip to zip).
Click to expand...
Click to collapse
Sorry to bother you bro but let's say I bricked my phone and have twrp installed......where will I get the stock recovery from and how to enter the fastboot mode of realme phone if it's bricked
AwesomeVk47 said:
Sorry to bother you bro but let's say I bricked my phone and have twrp installed......where will I get the stock recovery from and how to enter the fastboot mode of realme phone if it's bricked
Click to expand...
Click to collapse
Download stock recovery.
Enter fastboot mode using Power + Volume Down. If that does not work use other combinations.
Now flash stock recovery.
Enter recovery using
Code:
fastboot oem reboot-recovery
Install ozip.
Naveen56 said:
Download stock recovery.
Enter fastboot mode using Power + Volume Down. If that does not work use other combinations.
Now flash stock recovery.
Enter recovery using
Install ozip.
Click to expand...
Click to collapse
Is that link for realme 1 stock recovery?.......it would be great help if you could tell me how to obtain it....just for future use
---------- Post added at 03:18 PM ---------- Previous post was at 03:07 PM ----------
Naveen56 said:
Download stock recovery.
Enter fastboot mode using Power + Volume Down. If that does not work use other combinations.
Now flash stock recovery.
Enter recovery using
Install ozip.
Click to expand...
Click to collapse
Will this link work for stock rom file?
Link1
https://www.realme.com/in/support/software-update
Link2
https://www.getdroidtips.com/oppo-realme-1-stock-firmware-collections/
Which one of these should I use?