Database Info

HTC desire 816 soft bricked!

Hi guys,
I have a very bad problem with my HTC Desire 816G, it bricked and i can't now flash the stock or custom rom!
When i turn on my device it going to the stock recovery!
bootloader is unlock, i want to install the TWRP but i can't because i can't access the fastboot!
I don't know what i must do! I'm so worry and uneasy! plz help me...

alirezarz62 said:
Hi guys,
I have a very bad problem with my HTC Desire 816G, it bricked and i can't now flash the stock or custom rom!
When i turn on my device it going to the stock recovery!
bootloader is unlock, i want to install the TWRP but i can't because i can't access the fastboot!
I don't know what i must do! I'm so worry and uneasy! plz help me...
Click to expand...
Click to collapse
In stock recovery, if there's an option like 'Reboot into bootloader', that's the fastboot mode, enter it and flash TWRP..
If there's no other way, flash the original firmware from here: http://androidtechnics.blogspot.in/2015/06/htc-desire-816g-htc-d816h-dual-sim.html using SP Flash Tool..
How did you soft-brick your device first of all?

GokulNC said:
In stock recovery, if there's an option like 'Reboot into bootloader', that's the fastboot mode, enter it and flash TWRP..
If there's no other way, flash the original firmware from here: using SP Flash Tool..
How did you soft-brick your device first of all?
Click to expand...
Click to collapse
there is no option like that in the stock recovery!
i just downloaded the stock rom and tried to flash with SP Flash Tool but device is not detected by pc!
i unlocked the bootloader and then i reset the phone, device began updating with the stock update center for the stock rom! and...

alirezarz62 said:
there is no option like that in the stock recovery!
i just downloaded the stock rom and tried to flash with SP Flash Tool but device is not detected by pc!
i unlocked the bootloader and then i reset the phone, device began updating with the stock update center for the stock rom! and...
Click to expand...
Click to collapse
Install VCOM drivers and Android CDC Gadget drivers in computer and connect phone in switch off mode..

GokulNC said:
Install VCOM drivers and Android CDC Gadget drivers in computer and connect phone in switch off mode..
Click to expand...
Click to collapse
still doesn't detect! sorry, what do you mean of switch off mode?:crying:

alirezarz62 said:
still doesn't detect! sorry, what do you mean of switch off mode?:crying:
Click to expand...
Click to collapse
Remove battery for 5 secs, then put it inside and connect to computer

GokulNC said:
Remove battery for 5 secs, then put it inside and connect to computer
Click to expand...
Click to collapse
Unfortunately this device has no removable battery!
is there any other way?

I was trying to flash cm 12 thats how i bricked and sp flash tool is not working in my case. my boot loader is unlocked . when i reboot system from cwm recovery it restarts to cwm recover itself help fix plz.

QMobile Noir E2 Root Method (No Bootloader Unlock Method Added)

Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Code:
adb reboot bootloader
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Code:
fastboot oem unlock
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
fastboot reboot
Click to expand...
Click to collapse
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!ewVSyI7B!xAvgnzYORGFCtXLyxerNt9hx8Awz-5hNO2vlz5uabfo
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Code:
fastboot flash recovery **DRAG&DROP RECOVERY.IMG HERE**
Press enter
then type
Code:
fastboot reboot
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Code:
adb reboot recovery
and Press Enter
Phone should boot into TWRP
Disconnect from PC
Connect USB-OTG To Phone.
go to Mount and click on Select Storage and Choose USB-OTG
now go to Install and Choose The SUPERSU Update zip file and flash it.
AND REBOOT.
****************************************************************************************
Phone will reboot and during mid boot it will reboot again .... that is totally normal.
and Now Your Device is ROOTED Congrats
****************************************************************************************
If any dev wants to fix the recovery he can do it but give credit where its due .
External SDCard Works and This Recovery might as well work with Panasonic Eluga A3 as they both are identical copies of each other ...
************************************************************************************************************
Rooting With Locked Bootloader.
Pre-Requisites :
1 ) Locked Bootloader
2 ) SP FlashTool --> Download HERE
3 ) TWRP From Above or HERE
4 ) Modified Scatter File from HERE
5 ) Magisk Zip file and Magisk Manager and Keep them in SDCARD OR USB with OTG
******************************************************************************************************************
Flashing Stuff Guide.
Turn off Your Device
Download and Extract the SP Tool to some directory
Download the TWRP and Scatter file and keep them in a folder together
Rename the twrp file to recovery.img
Open SP Flash tool and Load the scatter file.
Below That set the Download Mode to Download Only, Not Firmware upgrade or Format + Download.
Then press the Green Download Button.
OR SEE HERE
Connect the usb cable to your mobile phone and not to the pc
Press and Hold the vol up and vol Down buttons simultaneously and connect the usb cable to the PC.
The Flashtool should Detect your device and start flashing the recovery img.
After completion device should be powered off.
Press and hold the vol UP button while powering up the device to boot into twrp.
In Twrp go to install and change storage to sdcard and locate the magisk zip file and install it.
after installation reboot to system. and install the magisk manager app
Congrats You have successfully rooted your device with a locked bootloader.:laugh::laugh:
Now with magisk you can install Xposed and various other mods systemlessly.
Enjoy
*************************************************************************
For and further inquiries comment below.

Reserved
1) SDCard works fine with recovery
2) Found identical device . Panasonic Eluga A3
3) Will test Recovery of Eluga A3 soon :fingers-crossed:

i have done all the steps you mentioned ..but it stucks on applying update from sd card...
USB-OTG is not showing ...when i try to update through sd card ,,,IT says ""Installation aborted"

bluedrago said:
i have done all the steps you mentioned ..but it stucks on applying update from sd card...
USB-OTG is not showing ...when i try to update through sd card ,,,IT says ""Installation aborted"
Click to expand...
Click to collapse
The Stock System of Noir E2 is Encrypted ..... all nougat based systems are encrypted
You need to backup all data in internal storage to your pc and go to TWRP and Go to Wipe and CLICK ON FORMAT DATA BUTTON
that will remove encryption and allow you to flash zip files

Do you have any custom rom for qmobile e2 like Cm14 rom or miui rom or any other
Bro i want another rom which can be flashed into the qmobile e2.The stock firmware is not good and it lags.
Also i don't like its stock firmware user interface.
So is there any way to flash another rom in it.
I searched alot about it but can't find any rom which can be flashed into it
And u r last hope.
I hope u will have any solution.:good:
Reply must. I am waiting.

Aqdas Iftikhar said:
Bro i want another rom which can be flashed into the qmobile e2.The stock firmware is not good and it lags.
Also i don't like its stock firmware user interface.
So is there any way to flash another rom in it.
I searched alot about it but can't find any rom which can be flashed into it
And u r last hope.
I hope u will have any solution.:good:
Reply must. I am waiting.
Click to expand...
Click to collapse
All I can share with you is the stock rom of Panasonic Eluga A3. If you want that do reply

Yes I Want Bro. Also share the method to port/Flash it. And have u tested it.
andromodgod said:
All I can share with you is the stock rom of Panasonic Eluga A3. If you want that do reply
Click to expand...
Click to collapse
Also tell me if everything is working on Panasonic rom like fingerprint sensor and sdcard etc.
I have read the specs of Panasonic eluga a3 and gsmarena shows that there is no fingerprint sensor in Panasonic eluga a3. So plz tell me that everything is working correctly or there is some bugs.
And share me the method to port/flash that rom.
I will me thankful to you.

Aqdas Iftikhar said:
Also tell me if everything is working on Panasonic rom like fingerprint sensor and sdcard etc.
I have read the specs of Panasonic eluga a3 and gsmarena shows that there is no fingerprint sensor in Panasonic eluga a3. So plz tell me that everything is working correctly or there is some bugs.
And share me the method to port/flash that rom.
I will me thankful to you.
Click to expand...
Click to collapse
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.

I got an error in sp flash tool and also Non removable battery problem
andromodgod said:
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
Click to expand...
Click to collapse
The error shown is given below:-
{Initializing scatter file failed. Please check the name of scatter file which you load is legal.}
Also it select only two files:-
1- logo
2- system
Plzz fix this problem and can u plz send me a video tutorial because my device has non removable battery and also not get detected in sp flash tool.
Thanks
---------- Post added at 03:05 PM ---------- Previous post was at 02:30 PM ----------
andromodgod said:
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
Click to expand...
Click to collapse
i old version of sp flash tool the file opens with an error
i tried new version 5.1524.00 but in that version the file even doesnt loads.'
plzz help me i am tired of the bugs which r present in qmobile os.
I will be very very thankful to u.

Aqdas Iftikhar said:
The error shown is given below:-
{Initializing scatter file failed. Please check the name of scatter file which you load is legal.}
Also it select only two files:-
1- logo
2- system
Plzz fix this problem and can u plz send me a video tutorial because my device has non removable battery and also not get detected in sp flash tool.
Thanks
---------- Post added at 03:05 PM ---------- Previous post was at 02:30 PM ----------
i old version of sp flash tool the file opens with an error
i tried new version 5.1524.00 but in that version the file even doesnt loads.'
plzz help me i am tired of the bugs which r present in qmobile os.
I will be very very thankful to u.
Click to expand...
Click to collapse
Download Latest Version of SP Flash tool from http://spflashtool.com
Then extract the Downloaded OS into a separate folder on your desktop.
Then open SPFlash tools and Switch off your device ...
Load the scatter file on to SPFlash tolls that you extracted ... It will be in the OS folder with all the .img files.
Press the start button.
Then connect your device to the PC ... Remember device must be switched off properly.
Flashing should begin automatically.

Many Thanks bro I have flashed the ROM successfully
Thanks for ur help.
After alot of stuggle and with your help I have successfully flashed Panasonic rom.
U said that there will be an update but I checked and it says the software is latest and no upset available.
Why in my phone there is no update??.

Aqdas Iftikhar said:
Thanks for ur help.
After alot of stuggle and with your help I have successfully flashed Panasonic rom.
U said that there will be an update but I checked and it says the software is latest and no upset available.
Why in my phone there is no update??.
Click to expand...
Click to collapse
i forgot ... the link that i shared had the lastest update already .

I tried to root my device and in fast boot i encountered a problem
andromodgod said:
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Code:
adb reboot bootloader
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Code:
fastboot oem unlock
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!KgMVgDwA!ImQoiSBUf9GitR5_K5Dxlzq01P0V4oqsZu5K2-RjZNQ
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Code:
fastboot flash recovery **DRAG&DROP RECOVERY.IMG HERE**
Press enter
then type
Code:
fastboot reboot
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Code:
adb reboot recovery
and Press Enter
Phone should boot into TWRP
Disconnect from PC
Connect USB-OTG To Phone.
go to Mount and click on Select Storage and Choose USB-OTG
now go to Install and Choose The SUPERSU Update zip file and flash it.
AND REBOOT.
****************************************************************************************
Phone will reboot and during mid boot it will reboot again .... that is totally normal.
and Now Your Device is ROOTED Congrats
****************************************************************************************
If any dev wants to fix the recovery he can do it but give credit where its due .
External SDCard Works and This Recovery might as well work with Panasonic Eluga A3 as they both are identical copies of each other ...
************************************************************************************************************
Rooting With Locked Bootloader.
Pre-Requisites :
1 ) Locked Bootloader
2 ) SP FlashTool --> Download HERE
3 ) TWRP From Above or HERE
4 ) Modified Scatter File from HERE
5 ) Magisk Zip file and Magisk Manager and Keep them in SDCARD OR USB with OTG
******************************************************************************************************************
Flashing Stuff Guide.
Turn off Your Device
Download and Extract the SP Tool to some directory
Download the TWRP and Scatter file and keep them in a folder together
Rename the twrp file to recovery.img
Open SP Flash tool and Load the scatter file.
Below That set the Download Mode to Download Only, Not Firmware upgrade or Format + Download.
Then press the Green Download Button.
OR SEE HERE
Connect the usb cable to your mobile phone and not to the pc
Press and Hold the vol up and vol Down buttons simultaneously and connect the usb cable to the PC.
The Flashtool should Detect your device and start flashing the recovery img.
After completion device should be powered off.
Press and hold the vol UP button while powering up the device to boot into twrp.
In Twrp go to install and change storage to sdcard and locate the magisk zip file and install it.
after installation reboot to system. and install the magisk manager app
Congrats You have successfully rooted your device with a locked bootloader.:laugh::laugh:
Now with magisk you can install Xposed and various other mods systemlessly.
Enjoy
*************************************************************************
For and further inquiries comment below.
Click to expand...
Click to collapse
Bro when i booted into fastboot after executing command to unlock bootloader in mobile it says to press volume up key and i pressed it again and again but no response but when i press volume down key it executes instantly and volume down key purpose is to not unlock bootloader.
plzz help me.
also in locked boot loader method sp flash tool says (enable dram failed) and thus i cannot flash recovery
.
plzzz help me out.
i have installed panasonic eluga a3 rom

Aqdas Iftikhar said:
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!KgMVgDwA!ImQoiSBUf9GitR5_K5Dxlzq01P0V4oqsZu5K2-RjZNQ
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Press enter
then type
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Bro when i booted into fastboot after executing command to unlock bootloader in mobile it says to press volume up key and i pressed it again and again but no response but when i press volume down key it executes instantly and volume down key purpose is to not unlock bootloader.
plzz help me.
also in locked boot loader method sp flash tool says (enable dram failed) and thus i cannot flash recovery
.
plzzz help me out.
i have installed panasonic eluga a3 rom
Click to expand...
Click to collapse
After pressing volume up.key few times ... Press the home button . Phone thinks that vol up is home button ... Dunno why that is though ??

andromodgod said:
After pressing volume up.key few times ... Press the home button . Phone thinks that vol up is home button ... Dunno why that is though
Click to expand...
Click to collapse
bro i have unlocked bootloader succesfully.
but when i give command to flash recovery the adb show tranfering and then ok.
but after reboot when i give command to reboot to recovery it boots into panasonic stock recovery.
plzz help me.
and also tell me why sp flash tool is giving me (failed to enable dram error) and give solution.
i hope u will have solution of these matter.
Many Thanks.:fingers-crossed::good:

Aqdas Iftikhar said:
bro i have unlocked bootloader succesfully.
but when i give command to flash recovery the adb show tranfering and then ok.
but after reboot when i give command to reboot to recovery it boots into panasonic stock recovery.
plzz help me.
and also tell me why sp flash tool is giving me (failed to enable dram error) and give solution.
i hope u will have solution of these matter.
Many Thanks.:fingers-crossed::good:
Click to expand...
Click to collapse
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.

I have rooted my device but cannot boot into system twrp opens again and again.
andromodgod said:
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
Click to expand...
Click to collapse
Bro after rooting my device i restarted my device but twrp recovery boots again and again and not boot the system.
in twrp i selected to reboot to system but it open twrp recovery again.
i wipe the data and cache but still twrp is openeing.
plzz help me i even cannot acces my device in this situation.
Reply fast.
---------- Post added at 05:46 AM ---------- Previous post was at 05:29 AM ----------
andromodgod said:
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
Click to expand...
Click to collapse
Bro tell me can i relock bootloader and remove or unflash twrp recovery after gaining root access.
if yes tell me how i can remove twrp recovery becasue it is irritating.
Plzz help me out.

When I click Mount/System it returns back to first option (Reboot) with a blink.
I am following first method.
Please help me.
PLzzzzzzzzzzzzzzz

PLz update the link of magisk zip file
The current link is not working. So plz update the link of magisk zip file.

FIXED: Mount Internal Storage in TWRP (Q Mobile Noir E2)
To mount internal storage in TWRP Recovery, Click on Wipe > Format Data > Type "yes" and Click on Ok. Then Reboot into Recovery. Now your Internal Storage is Mounted in TWRP. But it will format whole internal storage and factory reset rom so make a backup before doing this.

[2019] [root] [water7s] lyf water 7s ls-5507

This Method Is For Rooting Lyf Water 7 i.e LS-5504 running 6.0 android
Proceed At Your Own Risk I m Not Responsible For Any Damage To your Phone
To Begin Root Process First DOWNLOAD THESE FILES-
1. TWRP(working ported by me) Zippyshare Link
Mirror Mediafire link
2. Minimal ADB & Fasboot Tool for Android https://devsjournal.com/download-minimal-adb-fastboot-tool.html
3. Sp flash tool https://spflashtool.com/
4. Scatter files for our device https://www.mediafire.com/file/qy2be6cxv7e0j9r/MT6753~1.TXT/file Mirror - Zippyshare link
5. supersu zip Click here (this is property of chainfire all credits belong to them)
NOTE - Backup your contacts, messages and data in sd card or pc as it will be gone
Now follow instructions-
1. Install minimal ADB & Fastboot ( i prefer u install it in C:\ drive) Open the file named cmd. This will open a command prompt
2. Power off phone. Once it is off click volume up and power button together ,now screen will show a smalll menu/boot menu. Press volume up to move arrow to fastboot mode and select it by pressing volume down button. You will enter fastboot mode now.
3. Connect phone to pc using data cable. Come back to command prompt. Type this command.
PHP:
fastboot devices
it will show your device like 5DSOYL.. something like that
now type another command
PHP:
fastboot oem unlock
Now check your phone it will ask about unlocking bootloader press volume up key to agree
this will delete all data
after this type
PHP:
fastboot reboot
your bootloader is unlocked now
4. Keep device connected. once phone reboots, open Sp flash tool. select the scatter file (downloaded above) then on recovery tab select the recovery.img (download above). Click the download button and then power off your phone.
Twrp will be flashed, You can access it by Pressing volume up and power button together and selecting recovery in boot mode (where we selected fastboot mode)
5. To gain root just flash su zip through Twrp so simple
In case recovery don't get flashed there may be problem in sp flash tool drivers .. plz google how to install them
Still working in 2019, files updated to latest version and dead links replaced :good:

Any custom ROM available for this model?
I successfully rooted n installed TWRP recovery, now next step is to flash custom ROM so asking

DevanandaDS said:
Any custom ROM available for this model?
I successfully rooted n installed TWRP recovery, now next step is to flash custom ROM so asking
Click to expand...
Click to collapse
i have made one but not tested it yet....
i'll test it by tomorrow... if you want i can provide u the link

Yes Provide Me link i have to test that rom earlier.
ShaikhAaqib said:
i have made one but not tested it yet....
i'll test it by tomorrow... if you want i can provide u the link
Click to expand...
Click to collapse
Yes Provide Me link i have to test that rom earlier.

smit451 said:
Yes Provide Me link i have to test that rom earlier.
Click to expand...
Click to collapse
i will upload it tomorrow and give u the link bro...

Hello folks. Answering the questions above there is no custom rom for lyf water 7s. lyf water 7s don't has any sort of development on xda. I would advice not to mess around more then rooting because if you phone got hard brick (when it's stuck on logo) it won't be possible for you to flash it as sp flash tool will not recognize your device. Just get a new device.

MannyPanwar said:
Hello folks. Answering the questions above there is no custom rom for lyf water 7s. lyf water 7s don't has any sort of development on xda. I would advice not to mess around more then rooting because if you phone got hard brick (when it's stuck on logo) it won't be possible for you to flash it as sp flash tool will not recognize your device. Just get a new device.
Click to expand...
Click to collapse
true, but it is possible to port a rom for it, just that the procedure is difficult, since not many people use this device there is no development on this i guess..
i tried to port a rom... but i failed, i guess i did not unlock the BL... no idea.. it didn't go well..

Boot Freezing after twrp installation

Hi !
I had follow this thread https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768
and I had install TWRP but now when i try to start my phone,I can access to TWRP and fastboot but I can't access to the system.
My Nokia 3 freeze on "Powered by Android - Orange state -Your device has been unlocked and can't be trusted - Your device will boot in 5 seconds"
------
Nokia 3 - 1032 / Dowgraded to 7.0
Somebody help me plz ! :fingers-crossed:

>Taps< said:
Hi !
I had follow this thread https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768
and I had install TWRP but now when i try to start my phone,I can access to TWRP and fastboot but I can't access to the system.
My Nokia 3 freeze on "Powered by Android - Orange state -Your device has been unlocked and can't be trusted - Your device will boot in 5 seconds"
------
Nokia 3 - 1032 / Dowgraded to 7.0
Somebody help me plz ! :fingers-crossed:
Click to expand...
Click to collapse
Did you unlocked your bootloader and after that did you flash TWRP without reboot?
Maybe I'm wrong but when you unlock your bootloader, the phone automatically reboots into stock recovery and and immediately wipe everything (included your internal storage) and then reboots normally. If you flashed TWRP after unlocking your bootloader, your phone will boot into TWRP but it won't wipe anything.
I think that happened.

Isrks said:
Did you unlocked your bootloader and after that did you flash TWRP without reboot?
Maybe I'm wrong but when you unlock your bootloader, the phone automatically reboots into stock recovery and and immediately wipe everything (included your internal storage) and then reboots normally. If you flashed TWRP after unlocking your bootloader, your phone will boot into TWRP but it won't wipe anything.
I think that happened.
Click to expand...
Click to collapse
Mmh after I unlocked the bootloader, my phone was freeze on this
Select Boot Mode :
[VOLUME_UP to select. VOLUME DOWN is OK]
[Recovery Mode]
[Fastboot Mode] <<==
[Normal Mode]
=> FASTBOOT mode.....
So, I forced it to reboot, after everything seems ok.
What part must I reflash ?

>Taps< said:
Mmh after I unlocked the bootloader, my phone was freeze on this
Select Boot Mode :
[VOLUME_UP to select. VOLUME DOWN is OK]
[Recovery Mode]
[Fastboot Mode] <<==
[Normal Mode]
=> FASTBOOT mode.....
So, I forced it to reboot, after everything seems ok.
What part must I reflash ?
Click to expand...
Click to collapse
When I unlocked the bootloader my phone freezed too, so I typed in Windows cmd "fastboot reboot". After that, my phone was formatted by stock recovery.
You should reflash stock recovery if you have TWRP, so the stock recovery can format your internal storage, if not, your phone won't boot.
:fingers-crossed:

Isrks said:
When I unlocked the bootloader my phone freezed too, so I typed in Windows cmd "fastboot reboot". After that, my phone was formatted by stock recovery.
You should reflash stock recovery if you have TWRP, so the stock recovery can format your internal storage, if not, your phone won't boot.
:fingers-crossed:
Click to expand...
Click to collapse
Ok, so fastboot didn't work at all (just waiting devices)
I tried to reflash TWRP nothing happens, I tried to do a factory wipe with twrp but nothing happens too.
I searched a stock recovery for nokia 3 1032- Android 7.0 but found nothing - must i use stock recovery for Android 7.1.1 or do you have a link to a stock recovery for 7.0 ?
------------
I found this on XDA : Is it a good way if nothing work ?
Hi, I was able to unbricked my phone using this:
"https://mega.nz/#F!0lMBiIIYgB!c9TeOWFrKpf0XfOwXzunrg"
Here is the SP Flash tool, the download agent for Nokia's phones and the ROM unpacked
As SkaboXD said (i don't know if it were in this post or in other one) you must:
1- Download the files I provided you
2- Install SP Flash Tool
3- Choose the download agent
4- Choose the scatter
5- Press download and plug your phone (it must be OFF)
6- Wait and enjoy.
I must thank to everyone who give us this files. I couldn't unbricked my phone without your help
Click to expand...
Click to collapse

>Taps< said:
Ok, so fastboot didn't work at all (just waiting devices)
I tried to reflash TWRP nothing happens, I tried to do a factory wipe with twrp but nothing happens too.
I searched a stock recovery for nokia 3 1032- Android 7.0 but found nothing - must i use stock recovery for Android 7.1.1 or do you have a link to a stock recovery for 7.0 ?
------------
I found this on XDA : Is it a good way if nothing work ?
Click to expand...
Click to collapse
I think that this is the link:
https://forum.xda-developers.com/nokia-3/help/nokia-3-preloader-bricked-t3719357/post76069467#post76069467
I used SP flash tools to downgrade and install TWRP in my phone.
Which tool did you use to downgrade your phone?

Isrks said:
I think that this is the link:
https://forum.xda-developers.com/nokia-3/help/nokia-3-preloader-bricked-t3719357/post76069467#post76069467
I used SP flash tools to downgrade and install TWRP in my phone.
Which tool did you use to downgrade your phone?
Click to expand...
Click to collapse
Ok thanks :fingers-crossed:, I will try it
To downgrade I used OST LA and to flash TWRP I used SP flash tools

>Taps< said:
Ok thanks :fingers-crossed:, I will try it
To downgrade I used OST LA and to flash TWRP I used SP flash tools
Click to expand...
Click to collapse
Good luck. :fingers-crossed:
You can flash again with OST LA. Or try to flash with SP flash tool the whole rom or just the recovery. To flash with SP flash tools you need a nb0 unpacker tool (my previous post have a link to another post with the tool link).
BTW feel free to ask something that you don't understand. :highfive:

Isrks said:
Good luck. :fingers-crossed:
You can flash again with OST LA. Or try to flash with SP flash tool the whole rom or just the recovery. To flash with SP flash tools you need a nb0 unpacker tool (my previous post have a link to another post with the tool link).
BTW feel free to ask something that you don't understand. :highfive:
Click to expand...
Click to collapse
Heyyyyy !!! Thank you !!!
It works again :victory: !!!
I used OST LA to reflash it !!! Thanks again <3

I think I will use the second alternative step to not get a brick bootloader ^^' https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768
----------
Do you know the safest way to relock the bootloader ?

>Taps< said:
I think I will use the second alternative step to not get a brick bootloader ^^' https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768
----------
Do you know the safest way to relock the bootloader ?
Click to expand...
Click to collapse
Is like unlock bootloader, just change "fastboot oem unlock" to "fastboot oem lock".
But your internal storage will be formatted again by stock recovery, so you must have stock recovery installed.
After relock, your device will get ota updates, so you need stock recovery to install them.
I recommend root your device after all the updates, even you can install TWRP without problems.
I installed TWRP, root and installed stock recovery to get updates. Choose the method that you like.
Good luck. :highfive:

Unbrick your Realme C12

What is a brick?​If there is no usual way to recover your mobile, then it is called brick in my opinion. That means if you can't able to go to recovery and fastboot mode or the device is just blank with no sign of life.
When brick happens?​It will happen because of locking bootloader with custom images or just because of Mediatek/Realme strange behaviour.
What we have to do if brick happens?​Simply we have to flash stock firmware with Smart Phone Flash Tool(aka SPFlash Tool). With only SPFlash Tool we can't do anything, since we don't have permission for it. But with the advent of MTK-bypass, we can have full control over our device. If we don't have this MTK-bypass, then we have search for costly alternative's.
You can't flash only if your eMMC is damaged, which is the worst case because oppo phones are prone to eMMC failure.
Click to expand...
Click to collapse
Where to get firmware to flash?​Download decrypted .ofp firmware from https://drive.google.com/file/d/1SOmRxix9_UtjOLLanXPYxf4YK1NrA_RW/view
Thanks to @bx2_nero for it.
What is the procedure for using MTK-bypass and SPFlashTool?​MTK-bypass is a Python script and it needs different USB ways for working. So with these two in place, we can get our work done.
Linux Users​For Linux we have to use FireISO or patched kernels for working of MTK-bypass.
Use the Linux guide by @bx2_nero at https://forum.xda-developers.com/t/...our-realme-6-6i-india-6s-linux-method.4251077
Windows Users​For Windows we have to use libusb32 filter for MTK-bypass working.
Use the guide by @daeSundae at https://forum.xda-developers.com/t/...india-6s-using-spflash-tool-for-free.4222027/
MTK-bypass Official instructions​See Github ReadMe at https://github.com/MTK-bypass/bypass_utility and XDA support thread at https://forum.xda-developers.com/t/mod-dev-mediatek-mtk-auth-bypass-sla-daa-utility.4232377/
Credits​xyzz / xyz`: GitHub | XDA
chaosmaster / k4y0z: GitHub | XDA
Dinolek: GitHub | XDA
References​- https://forum.hovatek.com/thread-37957.html
- https://www.xda-developers.com/bypass-mediatek-sp-flash-tool-authentication-requirement/
- https://forum.xda-developers.com/t/repair-dead-hard-bricked-realme-3-3i-tutorial.4224255/
- https://forum.xda-developers.com/t/...d-flash-in-edl-with-no-auth-for-free.4229683/
- https://forum.xda-developers.com/t/...ash-tool-authentication.4236881/post-84627359

MTKClient
After MTK-bypass got success, @viperbjk who is a reverse engineer came up with a FOSS replacement of SP Flash Tool.
MTKClient combines MTK-bypass and SP Flash Tool together and with many improvements and new features.
Ability to flash partitions without Scatter file
Ability to Readback partitions without specifying address and length
Ability to Format partitions without specifying address and length
Run multiple commands without reconnecting the device
Flash protected partitions(opporeserve2, special_preload, my_custom and cdt_engineering) with locked bootloader
Unlock bootloader without need of in-depth test/Deep testing app from Realme
GitHub - bkerler/mtkclient: MTK reverse engineering and flash tool
MTK reverse engineering and flash tool. Contribute to bkerler/mtkclient development by creating an account on GitHub.
www.github.com

Reserved

I need help, my C12 is stuck on fastboot mode. This happened after flashing a GSI using TWRP and flashing the image in the Super (System and Vendor) partition.
I tried rebooting to recovery mode by executing fastboot reboot recovery but it says that bootloader is not known.
I also tried to flash a GSI (taught it might fix the problem) using fastboot flash system system.img but it says that no partition named system exists.
Please suggest what I should do.

Bro, can you make a video about this? my realme c12 got hardbricked after I flashed ozip file from stock recovery while bootloader is unlocked. it got hardbricked when I reboot it after flashing ozip

DFM23 said:
Bro, can you make a video about this? my realme c12 got hardbricked after I flashed ozip file from stock recovery while bootloader is unlocked. it got hardbricked when I reboot it after flashing ozip
Click to expand...
Click to collapse
What is the present state of the device? Can you able to boot to fastboot mode?

HemanthJabalpuri said:
What is the present state of the device? Can you able to boot to fastboot mode?
Click to expand...
Click to collapse
it has no sign of life, cant go to recovery or fastboot. when I connect it to pc it goes connect and disconnected.

How can I reboot to recovery mode when in fastboot mode? The command fastboot reboot recovery is not working for me.

youcancallmekhen said:
How can I reboot to recovery mode when in fastboot mode? The command fastboot reboot recovery is not working for me.
Click to expand...
Click to collapse
Use latest platform tools

youcancallmekhen said:
How can I reboot to recovery mode when in fastboot mode? The command fastboot reboot recovery is not working for me.
Click to expand...
Click to collapse
HemanthJabalpuri said:
Use latest platform tools
Click to expand...
Click to collapse
Sir I've finally able to reboot to recovery. I've tried flashing the OZIP file for my model but after some time it says Installation failed. When I was still using custom recovery, I wasn't able to mount System and Vendor. My bootloader is also unlocked sir.
Should I lock my bootloader sir?

youcancallmekhen said:
Should I lock my bootloader sir?
Click to expand...
Click to collapse
Don't lock bootloader.
Download this https://drive.google.com/file/d/1jLdDz7M0G_KPDn4jXjTeuFnO1C-MFaBs/view (It is from A.87 UI 1.0 Stock ROM)
Extract above 7z file and flash ONLY super partition from it and TWRP from https://androidfilehost.com/?fid=7161016148664807816 with below commands
Code:
fastboot -w
fastboot flash super super.img
fastboot flash recovery TWRP.img
fastboot reboot recovery
Now enable 'Skip Treble Compatibility error' in TWRP settings and flash stock ROM .ozip in TWRP.
Thanks

HemanthJabalpuri said:
Don't lock bootloader.
Download this https://sourceforge.net/projects/realmec11/files/Fastboot-ROM/[email protected]/download
Extract above 7z file and flash ONLY super partition from it with below commands
Code:
fastboot -w
fastboot flash super super.img
fastboot flash recovery stock-recovery.img
fastboot reboot recovery
Now flash stock ROM .ozip in stock recovery.
Thanks
Click to expand...
Click to collapse
Oh my, thank you so much sir. You have no idea how much you are helping me sir! My parents will be so happy, and we won't waste money… Thank you so much sir…
I'll update you sir after doing these, thank you sir! ♥

HemanthJabalpuri said:
Don't lock bootloader.
Download this https://sourceforge.net/projects/realmec11/files/Fastboot-ROM/[email protected]/download
Extract above 7z file and flash ONLY super partition from it with below commands
Code:
fastboot -w
fastboot flash super super.img
fastboot flash recovery stock-recovery.img
fastboot reboot recovery
Now flash stock ROM .ozip in stock recovery.
Thanks
Click to expand...
Click to collapse
I don't have much data left today sir, so I will download this later. Thank you very much again sir, you're my hero!

DFM23 said:
it has no sign of life, cant go to recovery or fastboot. when I connect it to pc it goes connect and disconnected.
Click to expand...
Click to collapse
Follow the guide and you can get your mobile back to life.
Thanks

HemanthJabalpuri said:
Follow the guide and you can get your mobile back to life.
Thanks
Click to expand...
Click to collapse
thank you bro, Ill follow your guide then. btw does the RMX2185 firmware you provided works with realme c12? I look it up and saw that it was for realme c11

DFM23 said:
thank you bro, Ill follow your guide then. btw does the RMX2185 firmware you provided works with realme c12? I look it up and saw that it was for realme c11
Click to expand...
Click to collapse
Yes, both use same firmware.

I tried the guide but when I click download on sp flash tool it would stay in red bar for 1 min or more then message will appear saying STATUS_EXT_RAM_EXCEPTION. I have read a same comment here in xda about realme c12 I dont know if its only on realme c12.

Thanks for your works sir, you are super awesome!

I rooted My Device (Realme X2 Pro) by Magisk. And Since My Device Bootloader was unlocked I Unrooted/Uninstalled MAgisk.
While Locking Bootloader My Device is Stuck where It displays { The Current Image (boot/recovery) have been destroyed dand cannot boot. Please flash the correct Image or Contact Customer Service to fix it }
While Trying to ENter the Fast Boot Mode {By pressing Volume + - and Power Button} Its Unresponsive
It shows Realme Logo And chrging Display for a Instant
Do you Know any way around to fix my Problem?

Bhuprab said:
I rooted My Device (Realme X2 Pro) by Magisk. And Since My Device Bootloader was unlocked I Unrooted/Uninstalled MAgisk.
While Locking Bootloader My Device is Stuck where It displays { The Current Image (boot/recovery) have been destroyed dand cannot boot. Please flash the correct Image or Contact Customer Service to fix it }
While Trying to ENter the Fast Boot Mode {By pressing Volume + - and Power Button} Its Unresponsive
It shows Realme Logo And chrging Display for a Instant
Do you Know any way around to fix my Problem?
Click to expand...
Click to collapse
Since your device is Qualcomm, I don't know. In any device, we have to flash stock rom (or atleast the partitions that are modified) to get device in working state.
You may get better help at https://forum.xda-developers.com/f/realme-x2-pro-questions-answers.9439/
Thanks