Related
Soft Bricking ?
Phone starts and stuck on the Yu logo.
Hard Bricking?
Phone does not start even if the battery is full. Have to go to the service center.
[Note]
1.Make sure that you have 70-80% battery on your phone.
2.You need a PC and a USB cable to connect your phone to the PC.
3.Flashing the factory firmware will wipe all the data present in the internal memory. So, make a backup of that if you can.
[Required Downloads]
1.Download the flash tools.
2. Download the factory firmware (signed fastboot)
3. adb setup drivers.
4. Mirror for drivers manual install here.
5. You can use this tool performs various functions.
# [Install Adb Derives Manually]
1. First of all extract the downloaded file and save it in the computer.
2. Before installation you have to disable the "signature verification" in windows. In windowa 8 or 10 you can do it by going to advanced settings or you can google the way of disabling signature verification.
3. After that turn off the phone and connect it pressing vol up that it will boot in fastboot mode.
4. When you connect the phone go device manager and search for device connected showing error sign.
5. Now click on that device and check for deriver update.
6. Now select the deriver in computer not automatically and select all devices.
7. Now select "have disk"
8. Browse the folder where you had extracted the adb drivers.
9. Now select the drivers file and install.
10. Ignores the Warning and select "always allow"
11. When finished check the device again by connecting to computer in fastboot mode with usb.
# [Flash Factory Firmware]
Steps
1. Extract the flashtools zip in a new folder on the desktop.
2. Extract the factory firmware zip in the same folder and make sure that all of the flashtools files are also present.
3. Now, power off your phone. If you are stuck in a bootloop, then pull out the battery and reinsert it. (Do not switch on the phone.)
4. While pressing the Volume Up key, connect your phone to the PC with the help of a USB cable.
5. You should now see the fastboot logo on your device. If you did, leave the Volume Up key. (If you do not see the logo, retry the process.)
6. Now go to the folder where you extracted the flash tools and factory firmware and run the flash-all.bat by double clicking on it.
7. A command window will open and the flashing procedure will start. (Make sure that your device does not disconnect from your PC during the procedure.)
8. The command window will automatically close once the procedure is completed.
9. Disconnect your device and boot it up by pressing the Power button. The first boot might take around 5-10 minutes to complete.
Congrats!
# [Recovey Installation (Very Easy Method)]
Note
1. Phone must has unlocked bootloader.
2. It must be rooted.
Steps
1. Download the twrp.img file and place it into your phone storage.( you can choose any custom recovery)
2. Now download the app from playstore flashify
3. Now install it and open the app it will require permission for root access, allow the root access.
4. Now open the app and u can backup the current recovery.
5. Now select the "flash" menu and select the "recovry image" and choose the .img file from storage.
6. Then select yes for flashing warning and will says flashing recovery. After completion it will say flash completed.
7. Now select the option button on right top corner and select the reboot into recovery.
8. Now it will reboot into recovery.
Hit "Thanks" if found this thread helpful....
Thanks for the solution...... it works well !!
Though my yuphoria was working perfectly fine, i wanted to factory reset my mobile for some reasons, which i was not able to do. Both soft and hard custom recovery options were not working (no recovery screen pop up, mobile boots and stuck at YU logo ), tried your solution and it worked.
Just one input for new users like me, where you have asked users to install adb drivers, i tried that part but on running the bat file, the device was not detected, hence had to add yuphoria device drivers from their official site, i am not able to paste the link here but file name is YUPHORIA_drivers-v1.0.zip, also USB debugging option needs to be turned on in developer option for this solution to work.
Rest all steps work exact as you explained.
Sahilsharma said:
Though my yuphoria was working perfectly fine, i wanted to factory reset my mobile for some reasons, which i was not able to do. Both soft and hard custom recovery options were not working (no recovery screen pop up, mobile boots and stuck at YU logo ), tried your solution and it worked.
Just one input for new users like me, where you have asked users to install adb drivers, i tried that part but on running the bat file, the device was not detected, hence had to add yuphoria device drivers from their official site, i am not able to paste the link here but file name is YUPHORIA_drivers-v1.0.zip, also USB debugging option needs to be turned on in developer option for this solution to work.
Rest all steps work exact as you explained.
Click to expand...
Click to collapse
Yup bro its difficult to set bootloader driver for yuphoria. But you can install it manually. But always remember to "disable driver signature verification" before installation and i will update the derivers link for manual installation if you message me the link.
will this work on unlocked bootloader
nickjones1007 said:
will this work on unlocked bootloader
Click to expand...
Click to collapse
"yup"... it will work. There is nothing to do with boot loader. It will flash the stock rom and boot-loader will get locked again. You have to unlock the boot-loader again if you want to flash custom rom again.
And i will get the official ota updates from YU as well ?
Sent from my YU5010 using Tapatalk
nickjones1007 said:
And i will get the official ota updates from YU as well ?
Sent from my YU5010 using Tapatalk
Click to expand...
Click to collapse
yep bro.. you will get the updates and i don't think you know that, there are no restrictions for unlocking/locking boot-loader of YU mobile. I mean the warranty not void if you unlock the boot-loader.
Thnx a lot bro and yeah i knw that ... Actually i'm gonna start installing roms so in case if it goes wrong i just a needed reliable method to get back on stock company's software ....
Thnx again bro
Sent from my YU5010 using Tapatalk
nickjones1007 said:
Thnx a lot bro and yeah i knw that ... Actually i'm gonna start installing roms so in case if it goes wrong i just a needed reliable method to get back on stock company's software ....
Thnx again bro
Sent from my YU5010 using Tapatalk
Click to expand...
Click to collapse
its reliable bro and worked for me when i screwed my phone. But note one thing that you should have installed the adb drivers properly on your computer. Anyway if u screwed up don't hesitate to discuss here.
When i start the flashall.bat the phone restarts and stuck back at the cyanogen logo..!
goudaniket said:
When i start the flashall.bat the phone restarts and stuck back at the cyanogen logo..!
Click to expand...
Click to collapse
Is driver properly installed? Or retry to download setup again if you have done right then
1. boot into bootloader
2. run bat file it will take some time. If all goes well then it will say about relocking of boot-loader.
3. seletct yes and restart.
4. you will see yu logo and it will take 10-15 minutes to load so stay calm! If it doesn't load then try again.
awesome... worked for me
maazkazi91 said:
awesome... worked for me
Click to expand...
Click to collapse
You can simply hit the thanks buttton bro
Can u remember me?
I can't root my YU 5010a
ankityu said:
I can't root my YU 5010a
Click to expand...
Click to collapse
I think you have issue with adb driver .. Is that resolved?
No man
...its still stuck in there..
ankityu said:
No man
...its still stuck in there..
Click to expand...
Click to collapse
Bro i hv updated the thread with steps to install adb drivers. Try it and then report if it works.
What is signed fastboot
ankityu said:
What is signed fastboot
Click to expand...
Click to collapse
Install it . these are the drivers.
After experiencing help from the fantastic meizu community i have decided to make a guide for unbricking this device. This guide is aimed to help people with M3 or M3s that cannot boot. Please only follow these steps to unbrick your device
I am not responsible for bricked devices and exploding phones due to following these steps.
By following these steps you agree that it is you, yourself that chose to follow these steps and I will not take any responsibility for your loss.
Before Starting
1. Can you boot ?
No. Go to Question 2.
Yes. You have came to the wrong place, but feel free to finish reading.2. Do you see the flyme logo when you boot?
Yes. Goto Stuck on Flyme Logo
No. Go to Question 33. Do you see the Meizu Logo and phone reboots over and over
Yes. Go to Testing
No. You flashed a wrong or damaged preloader, chances of unbricking LOW, Go to Sp Flash Tool
Testing
1. Shutdown your phone by holding power button (if you can)
2. Turn on phone with power + volume up until vibrates
I see a flyme logo & recovery options, Goto Stuck on Flyme Logo
Still rebooting, Continue
3. Turn on phone with power + volume down until vibrates
I see the words 'fastboot' at bottom, Go to Sp Flash Tool
I see nothing, your preloader is dead, I cannot help you :crying:.
Sp Flash Tool
Requirements
Micro USB cable (plug phone to pc)
Computer (prefer windows)
Internet to download
1. Download SP_Flash_Tool Link below
2. Download Firmware for your device (latest)
M3 Link https://downloads.meizufans.eu/?dir=m3/firmware/stable
M3s Link https://downloads.meizufans.eu/?dir=m3s/firmware/stable3. Download scatter file 'MT6750_android_scatter.txt' Link below
4. Use sp_flashtool (flashtool.exe)
A. Uncompress SP_Flash_Tool.zip into pc
B. Uncompress 'update.zip' (the firmware)
C. Copy downloaded scatter file 'MT6750_android_scatter.txt' to update folder
D. 'Run as Administrator' flash_tool.exe file
E. Go to the menu Options -> connection - > usb full speed with battery
F. For download agent select DA_PL.BIN from the same folder
G. Load the downloaded scatter file 'MT6750_android_scatter.txt' in update folder
H. Select the 'download only' option (don't press download yet)
I. Untick all the ROM at the bottom.
J. Suggest to select and flash one ROM at a time (except userdata and boot)
recovery
m1img
md1dsp
md1arm7
md3img
lk
lk2
tee1
tee2WARNING do NOT flash 'preloader'
K. Flash by clicking download
L. Turn on and connect phone to computer when vibrate
M. Wait for download to complete, with a green tick.
N. After flashing all ROM, now flash boot.5. Power on your phone.
6. Did it work?
No, Still in reboot cycle, Retry from the top, or use different update.zip
Yes, i have boot to flyme logo but stuck in boot logo, goto Stuck on Flyme Logo
Yes, i have boot to flyme logo and my phone is back, Congrats.
Links
Scatter File: https://drive.google.com/file/d/0B3pRT6ewL6tqeWZhQThFRGVwbE0/view?usp=sharing
SP Flash Tool.zip:
https://drive.google.com/file/d/0B3pRT6ewL6tqSW8tNTQ1OFY2eXc/view?usp=sharing
Stuck on Flyme Logo
You see the flyme logo, and the logo spins couple every couple of sec and waited for over 30 min and still does not boot.
Get in recovery mode, two ways choose one.
Method one (easy)
1. Turn off Phone (Force by holding power button)
2. Turn on Phone with power + volume
If it does not work go to Sp Flash Tool or Method two
Yes, my devices is now in recovery mode, continue the steps, skip Method two
Method two (need computer and harder)
1. Turn on the Phone where the logo spins
2. install adb on computer (link http://forum.xda-developers.com/showthread.php?t=2588979)
3. Plug phone into computer and get drivers for adb
4. Type 'adb devices' in cmd
5. If you get a device in the list continue by Typing 'adb reboot recovery'
'adb devices' not displaying devices (try method one or install driver)
'adb reboot recovery' reboots phone but not to recovery, this confirms that the recovery partition is damaged follow the steps in Sp Flash Tool
Yes, my devices is now in recovery mode, continue the stepsDownload Firmware for your device (latest)
M3 Link https://downloads.meizufans.eu/?dir=m3/firmware/stable
M3s Link https://downloads.meizufans.eu/?dir=m3s/firmware/stable
Plug Phone (in recovery mode) to computer. Copy the downloaded file 'update.zip' into the removable device named 'recovery' (do not unzip)
Tick the top option (system upgrade) and click 'start'
Wait be patient.:fingers-crossed:
Special Thanks
Kokotonix, this is a build up of Kokotonix's post link here: https://forum.meizufans.eu/topic/65...om-bootloop-meizu-logo-and-constant-reboot/11
Meizufans, thanks for this website and everyone in it, where i got most of the information from.
Questions & Answers
Q. Why is my phone unrepairable if i can get to fastboot?
A. By not being able to access fastboot means the preloader partition is damaged and SP Flash Tool will not work.Q. Why is my phones not bootable.
A. It could be caused by many factors but mainly caused by failure in updating firmware due to no battery or incorrect flashing of ROM.Q. Why is it so hard to recover meizu phones
A. Meizu phone uses the new mt67xx which is not supported by MTK droid tool causing problems for users to obtain the scatter file, and also the locked bootloader leading the users not being able to recover the devices the traditionally using fastboot.Q. I have a m3 note can i use this method?
A. Yes if anyone gets there hands on the mt6755 scatter file for meizu. But if not NoQ. HELP ME IT'S NOT WORKING!!!
A. Calm down, follow the steps again, if not comment below.Q. How do i brick my device
A. Get root and flashify and flash a random .img as the kernel. (it works i tried)
Thank you for Reading and wish you for the best on this device.
Comment below for help and also share you success.
reserved
phone is dead(
More info? You lost your preloader
Sent from my M3s using XDA-Developers mobile app
bluecub1st said:
More info? You lost your preloader
Sent from my M3s using XDA-Developers mobile app
Click to expand...
Click to collapse
after installing damaged rom its completely dont turn on only when you plug it to pc it recognize it like MTK Usb Port
logirus said:
after installing damaged rom its completely dont turn on only when you plug it to pc it recognize it like MTK Usb Port
Click to expand...
Click to collapse
Any display? or just black?
What rom did you install? If official you might be able to get a replacement through warranty.
Try SP Flash Tools, instruction in the first post. Chances are low but test if it detects after pressing download.
bluecub1st said:
Any display? or just black?
What rom did you install? If official you might be able to get a replacement through warranty.
Try SP Flash Tools, instruction in the first post. Chances are low but test if it detects after pressing download.
Click to expand...
Click to collapse
i installed from official firmware after installing it rebooted and never turn on no vibration nothing(no warranty i bought it from china on aliexpres) and please look at error ive got sp flash tool
Wrong download agent use the one I used in guide DA_PL.BIN
Sent from my M3s using XDA-Developers mobile app
Looks like it detects it phone u have hope
Sent from my M3s using XDA-Developers mobile app
bluecub1st said:
Wrong download agent use the one I used in guide DA_PL.BIN
Sent from my M3s using XDA-Developers mobile app
Click to expand...
Click to collapse
i used DA_PL.BIN and got the same error, maybe bootloader is locked thats why this error?
The error shows when your device started before the software can flash anything. SP flash tools works with locked bootloader, maybe your preloader is 100% dead
Sent from my M3s using XDA-Developers mobile app
bluecub1st said:
The error shows when your device started before the software can flash anything. SP flash tools works with locked bootloader, maybe your preloader is 100% dead
Sent from my M3s using XDA-Developers mobile app
Click to expand...
Click to collapse
and no way to repair it?:crying: i think im gonna trash this chinese cellphone away and never buy meizu again
No recovery, Fastboot mode is working. What should I do with this error?
Is there a way to work on me with meizu m3 max
Hi,
SPFlashtools fails to connect dead bricked Meizu M3S
Connecting to USB system recognizes as
MediaTek DA USB VCOM Port (COM7)
But other ports including Preloader are not
Do I have any hope to recover phone?
After following these steps, one by one, no matter if all went OK, my phone (m3s) won’t boot and it seems it is completely dead now. It can’t turn on. Power button looks unresponsive. What should I do? Is there any help?
many thanks for this guide @bluecub1st . The problem I have with my M3s is that it boots perfectly fine and works well, i just cannot enter recovery by using Volume + and power, and flashing a new firmware from inside Flyme OS just reboots the phone. I can enter fastboot though no problem, but i tried to do the SP Flash tool method listed and I just get this error message:
ERROR : S_TIMEOUT (0x412)
Any ideas how to fix this and get my recovery back? Really need some help so i can flash flyme 6...
i got error from sp_flashtool
ERROR : STATUS_SEC_DL_FORBIDDEN (0X0020004)
help me please sir
ERROR : STATUS_SEC_WRITE_DATA_NOT_ALLOWED
what to do ?
phone dead... thnks
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Code:
adb reboot bootloader
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Code:
fastboot oem unlock
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
fastboot reboot
Click to expand...
Click to collapse
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!ewVSyI7B!xAvgnzYORGFCtXLyxerNt9hx8Awz-5hNO2vlz5uabfo
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Code:
fastboot flash recovery **DRAG&DROP RECOVERY.IMG HERE**
Press enter
then type
Code:
fastboot reboot
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Code:
adb reboot recovery
and Press Enter
Phone should boot into TWRP
Disconnect from PC
Connect USB-OTG To Phone.
go to Mount and click on Select Storage and Choose USB-OTG
now go to Install and Choose The SUPERSU Update zip file and flash it.
AND REBOOT.
****************************************************************************************
Phone will reboot and during mid boot it will reboot again .... that is totally normal.
and Now Your Device is ROOTED Congrats
****************************************************************************************
If any dev wants to fix the recovery he can do it but give credit where its due .
External SDCard Works and This Recovery might as well work with Panasonic Eluga A3 as they both are identical copies of each other ...
************************************************************************************************************
Rooting With Locked Bootloader.
Pre-Requisites :
1 ) Locked Bootloader
2 ) SP FlashTool --> Download HERE
3 ) TWRP From Above or HERE
4 ) Modified Scatter File from HERE
5 ) Magisk Zip file and Magisk Manager and Keep them in SDCARD OR USB with OTG
******************************************************************************************************************
Flashing Stuff Guide.
Turn off Your Device
Download and Extract the SP Tool to some directory
Download the TWRP and Scatter file and keep them in a folder together
Rename the twrp file to recovery.img
Open SP Flash tool and Load the scatter file.
Below That set the Download Mode to Download Only, Not Firmware upgrade or Format + Download.
Then press the Green Download Button.
OR SEE HERE
Connect the usb cable to your mobile phone and not to the pc
Press and Hold the vol up and vol Down buttons simultaneously and connect the usb cable to the PC.
The Flashtool should Detect your device and start flashing the recovery img.
After completion device should be powered off.
Press and hold the vol UP button while powering up the device to boot into twrp.
In Twrp go to install and change storage to sdcard and locate the magisk zip file and install it.
after installation reboot to system. and install the magisk manager app
Congrats You have successfully rooted your device with a locked bootloader.:laugh::laugh:
Now with magisk you can install Xposed and various other mods systemlessly.
Enjoy
*************************************************************************
For and further inquiries comment below.
Reserved
1) SDCard works fine with recovery
2) Found identical device . Panasonic Eluga A3
3) Will test Recovery of Eluga A3 soon :fingers-crossed:
i have done all the steps you mentioned ..but it stucks on applying update from sd card...
USB-OTG is not showing ...when i try to update through sd card ,,,IT says ""Installation aborted"
bluedrago said:
i have done all the steps you mentioned ..but it stucks on applying update from sd card...
USB-OTG is not showing ...when i try to update through sd card ,,,IT says ""Installation aborted"
Click to expand...
Click to collapse
The Stock System of Noir E2 is Encrypted ..... all nougat based systems are encrypted
You need to backup all data in internal storage to your pc and go to TWRP and Go to Wipe and CLICK ON FORMAT DATA BUTTON
that will remove encryption and allow you to flash zip files
Do you have any custom rom for qmobile e2 like Cm14 rom or miui rom or any other
Bro i want another rom which can be flashed into the qmobile e2.The stock firmware is not good and it lags.
Also i don't like its stock firmware user interface.
So is there any way to flash another rom in it.
I searched alot about it but can't find any rom which can be flashed into it
And u r last hope.
I hope u will have any solution.:good:
Reply must. I am waiting.
Aqdas Iftikhar said:
Bro i want another rom which can be flashed into the qmobile e2.The stock firmware is not good and it lags.
Also i don't like its stock firmware user interface.
So is there any way to flash another rom in it.
I searched alot about it but can't find any rom which can be flashed into it
And u r last hope.
I hope u will have any solution.:good:
Reply must. I am waiting.
Click to expand...
Click to collapse
All I can share with you is the stock rom of Panasonic Eluga A3. If you want that do reply
Yes I Want Bro. Also share the method to port/Flash it. And have u tested it.
andromodgod said:
All I can share with you is the stock rom of Panasonic Eluga A3. If you want that do reply
Click to expand...
Click to collapse
Also tell me if everything is working on Panasonic rom like fingerprint sensor and sdcard etc.
I have read the specs of Panasonic eluga a3 and gsmarena shows that there is no fingerprint sensor in Panasonic eluga a3. So plz tell me that everything is working correctly or there is some bugs.
And share me the method to port/flash that rom.
I will me thankful to you.
Aqdas Iftikhar said:
Also tell me if everything is working on Panasonic rom like fingerprint sensor and sdcard etc.
I have read the specs of Panasonic eluga a3 and gsmarena shows that there is no fingerprint sensor in Panasonic eluga a3. So plz tell me that everything is working correctly or there is some bugs.
And share me the method to port/flash that rom.
I will me thankful to you.
Click to expand...
Click to collapse
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
I got an error in sp flash tool and also Non removable battery problem
andromodgod said:
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
Click to expand...
Click to collapse
The error shown is given below:-
{Initializing scatter file failed. Please check the name of scatter file which you load is legal.}
Also it select only two files:-
1- logo
2- system
Plzz fix this problem and can u plz send me a video tutorial because my device has non removable battery and also not get detected in sp flash tool.
Thanks
---------- Post added at 03:05 PM ---------- Previous post was at 02:30 PM ----------
andromodgod said:
Everything works .... You will have to flash the OS via SP Flash tools so make backup of everything in your internal storage ... Also it comes with some preinstalled apps so you will have to delete those .... But over all it's a much more optimized system than the QMobile OS.
https://drive.google.com/uc?id=0B4KUp-X2vfc3aVpiQUdiQ293OGM&export=download
Download from above ... Flash using SP Flash tools and after setting phone up there will be a small update ... Install that and then flash twrp and install magisk and if you want install Xposed as well.
Enjoy.
Click to expand...
Click to collapse
i old version of sp flash tool the file opens with an error
i tried new version 5.1524.00 but in that version the file even doesnt loads.'
plzz help me i am tired of the bugs which r present in qmobile os.
I will be very very thankful to u.
Aqdas Iftikhar said:
The error shown is given below:-
{Initializing scatter file failed. Please check the name of scatter file which you load is legal.}
Also it select only two files:-
1- logo
2- system
Plzz fix this problem and can u plz send me a video tutorial because my device has non removable battery and also not get detected in sp flash tool.
Thanks
---------- Post added at 03:05 PM ---------- Previous post was at 02:30 PM ----------
i old version of sp flash tool the file opens with an error
i tried new version 5.1524.00 but in that version the file even doesnt loads.'
plzz help me i am tired of the bugs which r present in qmobile os.
I will be very very thankful to u.
Click to expand...
Click to collapse
Download Latest Version of SP Flash tool from http://spflashtool.com
Then extract the Downloaded OS into a separate folder on your desktop.
Then open SPFlash tools and Switch off your device ...
Load the scatter file on to SPFlash tolls that you extracted ... It will be in the OS folder with all the .img files.
Press the start button.
Then connect your device to the PC ... Remember device must be switched off properly.
Flashing should begin automatically.
Many Thanks bro I have flashed the ROM successfully
Thanks for ur help.
After alot of stuggle and with your help I have successfully flashed Panasonic rom.
U said that there will be an update but I checked and it says the software is latest and no upset available.
Why in my phone there is no update??.
Aqdas Iftikhar said:
Thanks for ur help.
After alot of stuggle and with your help I have successfully flashed Panasonic rom.
U said that there will be an update but I checked and it says the software is latest and no upset available.
Why in my phone there is no update??.
Click to expand...
Click to collapse
i forgot ... the link that i shared had the lastest update already .
I tried to root my device and in fast boot i encountered a problem
andromodgod said:
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Code:
adb reboot bootloader
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Code:
fastboot oem unlock
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!KgMVgDwA!ImQoiSBUf9GitR5_K5Dxlzq01P0V4oqsZu5K2-RjZNQ
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Code:
fastboot flash recovery **DRAG&DROP RECOVERY.IMG HERE**
Press enter
then type
Code:
fastboot reboot
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Code:
adb reboot recovery
and Press Enter
Phone should boot into TWRP
Disconnect from PC
Connect USB-OTG To Phone.
go to Mount and click on Select Storage and Choose USB-OTG
now go to Install and Choose The SUPERSU Update zip file and flash it.
AND REBOOT.
****************************************************************************************
Phone will reboot and during mid boot it will reboot again .... that is totally normal.
and Now Your Device is ROOTED Congrats
****************************************************************************************
If any dev wants to fix the recovery he can do it but give credit where its due .
External SDCard Works and This Recovery might as well work with Panasonic Eluga A3 as they both are identical copies of each other ...
************************************************************************************************************
Rooting With Locked Bootloader.
Pre-Requisites :
1 ) Locked Bootloader
2 ) SP FlashTool --> Download HERE
3 ) TWRP From Above or HERE
4 ) Modified Scatter File from HERE
5 ) Magisk Zip file and Magisk Manager and Keep them in SDCARD OR USB with OTG
******************************************************************************************************************
Flashing Stuff Guide.
Turn off Your Device
Download and Extract the SP Tool to some directory
Download the TWRP and Scatter file and keep them in a folder together
Rename the twrp file to recovery.img
Open SP Flash tool and Load the scatter file.
Below That set the Download Mode to Download Only, Not Firmware upgrade or Format + Download.
Then press the Green Download Button.
OR SEE HERE
Connect the usb cable to your mobile phone and not to the pc
Press and Hold the vol up and vol Down buttons simultaneously and connect the usb cable to the PC.
The Flashtool should Detect your device and start flashing the recovery img.
After completion device should be powered off.
Press and hold the vol UP button while powering up the device to boot into twrp.
In Twrp go to install and change storage to sdcard and locate the magisk zip file and install it.
after installation reboot to system. and install the magisk manager app
Congrats You have successfully rooted your device with a locked bootloader.:laugh::laugh:
Now with magisk you can install Xposed and various other mods systemlessly.
Enjoy
*************************************************************************
For and further inquiries comment below.
Click to expand...
Click to collapse
Bro when i booted into fastboot after executing command to unlock bootloader in mobile it says to press volume up key and i pressed it again and again but no response but when i press volume down key it executes instantly and volume down key purpose is to not unlock bootloader.
plzz help me.
also in locked boot loader method sp flash tool says (enable dram failed) and thus i cannot flash recovery
.
plzzz help me out.
i have installed panasonic eluga a3 rom
Aqdas Iftikhar said:
Backstory:
I Bought this device from Pakistan for Rs15500 or 147 US Dollars. It was a relatively cheap and good device and like all QMobile Devices i thought it would have a counterpart in the Micromax Community like my old phone Qmobile Noir A10 and as it is known in India as Micromax A110.
Sadly i was mistaken. i scoured the net for any device resembling mine and none were found ... well none that had Android 7 or the same chip set.
SO Last Night i Sat Down and Worked and Somehow i was able to port a semi-working TWRP Recovery for This Device :fingers-crossed:
It Doesn't currently mount the Internal Storage... External SDCARD WORKS :good:
AND NOW THE GUIDE TO ROOT.
****************************************************************************************
Pre-Requisites.
Unlocked Bootloader
ADB ON PC
USB With OTG Support or USB AND OTG CABLE
PATIENCE
****************************************************************************************
To Unlock Bootloader.
WARNING UNLOCKING BOOTLOADER WILL WIPE DEVICE SO BACK IT UP
Go TO Developer Options
Scroll Down to OEM UNLOCKING and Check it
Connect phone to PC
Then Open CMD and TYPE
Wait til it boots into fastboot mode [ Black screen with tiny text at bottom]
Then Type
Press enter and Follow guide on Phone screen
After Completion of Unlocking type
Boot into Device and Set it up
Then Download Recovery.img from https://mega.nz/#!KgMVgDwA!ImQoiSBUf9GitR5_K5Dxlzq01P0V4oqsZu5K2-RjZNQ
****************************************************************************************
FLASHING RECOVERY
Reboot back into bootloader and type
Press enter
then type
****************************************************************************************
ROOTING
Go to http://www.supersu.com/download and Download the Latest zip file.
Place the zip file on a usb.
Connect Phone to PC
Type
Bro when i booted into fastboot after executing command to unlock bootloader in mobile it says to press volume up key and i pressed it again and again but no response but when i press volume down key it executes instantly and volume down key purpose is to not unlock bootloader.
plzz help me.
also in locked boot loader method sp flash tool says (enable dram failed) and thus i cannot flash recovery
.
plzzz help me out.
i have installed panasonic eluga a3 rom
Click to expand...
Click to collapse
After pressing volume up.key few times ... Press the home button . Phone thinks that vol up is home button ... Dunno why that is though ??
andromodgod said:
After pressing volume up.key few times ... Press the home button . Phone thinks that vol up is home button ... Dunno why that is though
Click to expand...
Click to collapse
bro i have unlocked bootloader succesfully.
but when i give command to flash recovery the adb show tranfering and then ok.
but after reboot when i give command to reboot to recovery it boots into panasonic stock recovery.
plzz help me.
and also tell me why sp flash tool is giving me (failed to enable dram error) and give solution.
i hope u will have solution of these matter.
Many Thanks.:fingers-crossed::good:
Aqdas Iftikhar said:
bro i have unlocked bootloader succesfully.
but when i give command to flash recovery the adb show tranfering and then ok.
but after reboot when i give command to reboot to recovery it boots into panasonic stock recovery.
plzz help me.
and also tell me why sp flash tool is giving me (failed to enable dram error) and give solution.
i hope u will have solution of these matter.
Many Thanks.:fingers-crossed::good:
Click to expand...
Click to collapse
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
I have rooted my device but cannot boot into system twrp opens again and again.
andromodgod said:
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
Click to expand...
Click to collapse
Bro after rooting my device i restarted my device but twrp recovery boots again and again and not boot the system.
in twrp i selected to reboot to system but it open twrp recovery again.
i wipe the data and cache but still twrp is openeing.
plzz help me i even cannot acces my device in this situation.
Reply fast.
---------- Post added at 05:46 AM ---------- Previous post was at 05:29 AM ----------
andromodgod said:
After flashing recovery in fastboot . Use this command WHILE HOLDING VOL UP BUTTON
Fastboot reboot
Then phone will reboot into twrp recovery .
I'll need to research on the other one.
Click to expand...
Click to collapse
Bro tell me can i relock bootloader and remove or unflash twrp recovery after gaining root access.
if yes tell me how i can remove twrp recovery becasue it is irritating.
Plzz help me out.
When I click Mount/System it returns back to first option (Reboot) with a blink.
I am following first method.
Please help me.
PLzzzzzzzzzzzzzzz
PLz update the link of magisk zip file
The current link is not working. So plz update the link of magisk zip file.
FIXED: Mount Internal Storage in TWRP (Q Mobile Noir E2)
To mount internal storage in TWRP Recovery, Click on Wipe > Format Data > Type "yes" and Click on Ok. Then Reboot into Recovery. Now your Internal Storage is Mounted in TWRP. But it will format whole internal storage and factory reset rom so make a backup before doing this.
Code:
[CENTER]If You Have Hard Bricked Your Device Then Only Use This Guide[/CENTER]
CPH1861EX_11.A.29
Files You Need To Download:
1:Miracle Box Tool-https://mega.nz/#!lVsQGSaC!6TTJopMyntMQA0IKYdC_5BlsxIjV_Ibhx2qWL_ZqDyI
2:Stock Rom- https://mega.nz/#F!ncMFUaaa!0fVNwJ_Io0EMFv8YLjBZlQ [Select Download As Zip]
3:https://androidmtk.com/install-android-cdc-driver-manually [Install Drivers Using This Guide]
Click to expand...
Click to collapse
Steps To Flash Stock Rom:
1:Install Miracle Box And Drivers
2:Launch Miracle Box
3: Open Mtk Tab
4:Click on Services
5:Select Write From The Available Options
6:Select 8th Boot From Boot Options
7:In Second Options,Select Oppo Realme 1
8:Check Skip Preloader File
9:Hit Start
10:Now connect your phone and hold volume and power buttons... It will flash and turn off your phone
11:Remove Cable And Press Power+VOLUME Up For 15 Seconds
You Have Unbricked Your Device
Click to expand...
Click to collapse
Credits:
Hamza(From Telegram Group For Writing The Tutorial0
Shobith(For Stock Rom Dump)
AnuragRai(For Simplifying The Guide)
1st link miracle box is not working plz correct it bro
can you share download links from other providers? mega asks for premium account.
thank you.
Didn't work for me
anurag rai said:
Code:
[CENTER]If You Have Hard Bricked Your Device Then Only Use This Guide[/CENTER]
CPH1861EX_11.A.29
Credits:
Hamza(From Telegram Group For Writing The Tutorial0
Shobith(For Stock Rom Dump)
AnuragRai(For Simplifying The Guide)
Click to expand...
Click to collapse
After flashing twrp recovery when I booted my device, a software update popped up and it automatically updated over night and my device hard bricked. I tried everything but couldn't fix it. My pc is not even recognising my phone so can't follow your steps. Any suggestion or help to fix my device will be appreciated.
same mine bro,
rom version was a31 and after installed twrp, my device hard bricked. i couldnt solve yet, waiting a newer version of miracle box or etc.
anurag rai said:
Code:
[CENTER]If You Have Hard Bricked Your Device Then Only Use This Guide[/CENTER]
CPH1861EX_11.A.29
Credits:
Hamza(From Telegram Group For Writing The Tutorial0
Shobith(For Stock Rom Dump)
AnuragRai(For Simplifying The Guide)
Click to expand...
Click to collapse
i dumped the stock rom bro @besttipsYT Not Shobith
this method is not working at this time...when i trying to flash by this method only show.......phone connected......downloding boot8....then disconnect my phone ..&reboot
Please don't flash custom recovery (here twrp) without proper knowledge or just sake of modding device. The builds and methods are not always working and may end up bricking your device.
Hi There, Can someone PLZ help me setting up OPPO PRELOADER Drivers correctly. Everytime i try to use miracle thunder i get the following log:
Waiting for USB Port...
Set USB Serial Device (COM9)
Connecting to Phone,Wait..
Connected to Phone.
CPU: MT6771 SW:0000 Ver: CA00
>>Downloading Boot8 ...
and it remains on here forever.
Actually oppo preloader shows for some time in pc and after that it goes away and hence it is not letting the miracle thunder work properly (i guess)
when my phone was working (booting in coloros 6, then also oppo preloader was doing the same thing and after a few seconds my battery would start charging), now i can't see anything on screen as it's bricked now.
Preloader doesn't even work with SP Flash Tools also.
EDIT : I have tried almost everything i knew, drivers manager add legacy option etc.
If someone could help me get out of this problem, i would really be grateful.
Brick Reason : Flashed TWRP but used fastboot command to boot into that : (
PLEASE HELP SOMEONE
Alen012 said:
Hi There, Can someone PLZ help me setting up OPPO PRELOADER Drivers correctly. Everytime i try to use miracle thunder i get the following log:
Waiting for USB Port...
Set USB Serial Device (COM9)
Connecting to Phone,Wait..
Connected to Phone.
CPU: MT6771 SW:0000 Ver: CA00
>>Downloading Boot8 ...
and it remains on here forever.
Actually oppo preloader shows for some time in pc and after that it goes away and hence it is not letting the miracle thunder work properly (i guess)
when my phone was working (booting in coloros 6, then also oppo preloader was doing the same thing and after a few seconds my battery would start charging), now i can't see anything on screen as it's bricked now.
Preloader doesn't even work with SP Flash Tools also.
EDIT : I have tried almost everything i knew, drivers manager add legacy option etc.
If someone could help me get out of this problem, i would really be grateful.
Brick Reason : Flashed TWRP but used fastboot command to boot into that : (
PLEASE HELP SOMEONE
Click to expand...
Click to collapse
Miracle box, SP Flash Tool and MTK Droid Tools no longer work with Realme. If you can access Fastboot then flash stock recovery and proceed further.
Bootloop if i try t access fastboot mode. Can go to recovery but its not allowing me to flash amything saying its an older version. Any work around yet?
Naveen56 said:
Miracle box, SP Flash Tool and MTK Droid Tools no longer work with Realme. If you can access Fastboot then flash stock recovery and proceed further.
Click to expand...
Click to collapse
StripsOfTatti said:
Bootloop if i try t access fastboot mode. Can go to recovery but its not allowing me to flash amything saying its an older version. Any work around yet?
Click to expand...
Click to collapse
Which recovery are you in? Is it Stock or Custom?
If u have stock first wipe data and then flash boot.img or ozip file (stock ROM).
If u have custom recovery then you need to flash stock recovery + stock ROM.
plz help me ihave realme 1 and it stuck in logo and orange state and restart over and over and icannot boot into recovery or fastboot plz help me
Simba Gaara said:
plz help me ihave realme 1 and it stuck in logo and orange state and restart over and over and icannot boot into recovery or fastboot plz help me
Click to expand...
Click to collapse
If recovery and fastboot are inaccessible means you need to visit service center.
When trying to connect realme 1 to miracle it showing usb device not connected, how to solve this? Drivers are installed
Naveen56 said:
Miracle box, SP Flash Tool and MTK Droid Tools no longer work with Realme. If you can access Fastboot then flash stock recovery and proceed further.
Click to expand...
Click to collapse
So bro in case if I brick my phone then I can flash stock rom using stock recovery.......??
Do I get those Rom files from official realme website?
AwesomeVk47 said:
So bro in case if I brick my phone then I can flash stock rom using stock recovery.......??
Do I get those Rom files from official realme website?
Click to expand...
Click to collapse
Yes. Do remember you need both fastboot and recovery to be working, so you can flash Stock Recovery (only if you have TWRP installed).
If you have stock recovery installed then download stock rom from official Realme site and place it in the Sdcard (otg wont help). Enter into recovery and update/install the ozip.
If your phone is completely dead then above method wont help and you have to follow another one.
Note: If your device is rooted then installing (from stock recovery) stock rom fails. At this time flash TWRP from fastboot then flash zip file (convert stock rom from ozip to zip).
Naveen56 said:
Yes. Do remember you need both fastboot and recovery to be working, so you can flash Stock Recovery (only if you have TWRP installed).
If you have stock recovery installed then download stock rom from official Realme site and place it in the Sdcard (otg wont help). Enter into recovery and update/install the ozip.
If your phone is completely dead then above method wont help and you have to follow another one.
Note: If your device is rooted then installing (from stock recovery) stock rom fails. At this time flash TWRP from fastboot then flash zip file (convert stock rom from ozip to zip).
Click to expand...
Click to collapse
Sorry to bother you bro but let's say I bricked my phone and have twrp installed......where will I get the stock recovery from and how to enter the fastboot mode of realme phone if it's bricked
AwesomeVk47 said:
Sorry to bother you bro but let's say I bricked my phone and have twrp installed......where will I get the stock recovery from and how to enter the fastboot mode of realme phone if it's bricked
Click to expand...
Click to collapse
Download stock recovery.
Enter fastboot mode using Power + Volume Down. If that does not work use other combinations.
Now flash stock recovery.
Enter recovery using
Code:
fastboot oem reboot-recovery
Install ozip.
Naveen56 said:
Download stock recovery.
Enter fastboot mode using Power + Volume Down. If that does not work use other combinations.
Now flash stock recovery.
Enter recovery using
Install ozip.
Click to expand...
Click to collapse
Is that link for realme 1 stock recovery?.......it would be great help if you could tell me how to obtain it....just for future use
---------- Post added at 03:18 PM ---------- Previous post was at 03:07 PM ----------
Naveen56 said:
Download stock recovery.
Enter fastboot mode using Power + Volume Down. If that does not work use other combinations.
Now flash stock recovery.
Enter recovery using
Install ozip.
Click to expand...
Click to collapse
Will this link work for stock rom file?
Link1
https://www.realme.com/in/support/software-update
Link2
https://www.getdroidtips.com/oppo-realme-1-stock-firmware-collections/
Which one of these should I use?
Code:
By Doing this, You may Void your warranty..
Neither Me nor XDA is Responsible for any Damage Caused for Your Mobile..
If you show Finger at me, I'll laugh at you..
Why there is need for this Guide?
When I got my Realme 5, I wanted to Unlock the Bootloader, Install the TWRP Recovery, root it and finally Install a Custom ROM. So, I've Searched for it and Finally Disappointed B'coz many Guides were wrong and some were Very Old and Outdated Guides.. So I've Researched and now with many problems, Finally I've Unlocked the Bootloader, installed TWRP and finally Flashed LineageOS 17.1.. So, this Guide saves your time, I've Included the Steps What I did, you guys can simply follow it..
This Guide is only applicable for Realme 5(rmx1911) and not for Realme 5i, Realme 5s or Realme 5 Pro..
Click to expand...
Click to collapse
Things You need to Continue :
A Windows Laptop/PC (Windows because, I am showing the Procedure with Windows)
Minimal ADB and FastBoot
Recovery (I've flashed PitchBlack Recovery, but you can also do this procedure with TWRP recovery)
Of course a Realme5 (rmx1911)
In-Depth Test apk
All the Download Links of above files are in Attachments..
Click to expand...
Click to collapse
Procedure :
Steps to Downgrade from RealmeUI 1 to ColorOS 6
If you're in Latest android 10 RealmeUI, first you need to downgrade to ColorOS 6 android pie.
To do so, download ColorOS package(.ozip package) from below link.
Open this .ozip package with File Manager app and Locate this package.
Click on that package, A pop-up will appear, In that Select "Upgrade Now" or something like that..
It will wipe your data and It will boot into ColorOS setup, Complete the Setup..
Users who are in ColorOS 6, need not to follow above Steps!
Click to expand...
Click to collapse
Steps to Unlock Bootloader:
Enable developer options in settings and enable OEM Unlocking, USB Debugging from Developer Options from Settings.
Download and Install In-Depth apk from attachments.
Open it and Click on Start Applying.
After 20min Open app and click on "Query Verification Status" .(if you dont see like this wait for some moretime, maximum it will take upto 24hours only)
If you see something like "Review Successful", You are good to go..
Select "Start the in-depth test", You will be forwarded to fast boot mode..
Connect the mobile to PC.
Now comes the role of PC/Laptop, Download the Fastboot and Minimal ADB, Recovery.img and vbmeta.img From the attachments.
Extract that fastboot zip in some Directory, Copy the recovery.img and vbmeta.img to the fastboot folder.
Open the Minimal ADB and Fastboot and in that open "cmd-here.exe"
Type "fastboot devices", then enter, You should see something like serial number.
Type "fastboot flashing unlock", then enter, now check ur phone you will see something like "Unlock" or similar to something..
You need to select the Unlock with the help of volume button and select with power button.
After Selecting "Unlock" all data will be deleted and Your Phone will be unlocked..
HURRAY, YOUR PHONE IS UNLOCKED
Installing Pitchblack Recovery :
After Unlocking Phone all the Data will be deleted, complete the setup wizard and enable USB Debugging.
Connect the Phone to PC via USB.
Open ADB Fastboot folder and select "cmd-here.exe".
Type "adb devices" you should see something like Serial Number.(If you did not see, re-insert the phone cable to another port and check)
Type "adb reboot fastboot", You will be forwarded to Fastboot mode.
Type "fastboot flash recovery recovery.img"
Type "fastboot flash vbmeta vbmeta.img"
Disconnect the Mobile from PC, then click on Volume down Button Until you get Something Like "Recovery" and Select using Power Button.
HURRAY! YOU'VE INSTALLED RECOVERY
IF YOU WANT TO ROOT YOUR DEVICE, DOWNLOAD MAGISK AND INSTALL IT FROM RECOVERY
Click to expand...
Click to collapse
IF YOU WANT TO GO TO RECOVERY AGAIN JUST BOOT INTO FASTBOOT(Power-off Your device, click on volume down button and power button simultaneously, within few seconds you will boot into fastboot) THEN CLICK ON VOL- BUTTON UNTIL YOU GET RECOVERY OPTION, THEN SELECT IT USING POWER BUTTON
Click to expand...
Click to collapse
You've Unlocked BL, flashed RECOVERY, Installed Magisk, Now what? Go and Search for your Favourite ROMs and flash them
Realme 5 Downgrade package link
{Mod edit}
triplr_dev_users
Test forum for ROM Builders !
All roms Welcome, All devices welcome!
Samsung Note 3,4 Qualcomm and exynos 5433
Galaxy Tab S2
Realme 5(rmx1991)
All things RPi 4 Family
An open discussion on Tech, Dev and Life
Welcome .
Rule 1. Have fun
Rule 2. Be nice
{Mod edit}
Reserved
supper sir i have very usefull i have flashed a lineage 17.1
with ur guide and i have unlocked boot lodder also thank u very much well done sir
Sensui--moksha said:
supper sir i have very usefull i have flashed a lineage 17.1
Click to expand...
Click to collapse
Glad, this helped!!
Why happend like this in depth test ?
Bebe's said:
Why happend like this in depth test ?
Click to expand...
Click to collapse
Sorry for the delay bro, I think you can't unlock the bootloader of Your Phone, bcoz it is not directly from the realme, I mean the phone which u bought is customized by your sim(carrier) company
Hello. The Downgrade file is not in the attachments thanks
nezuxiv said:
Hello. The Downgrade file is not in the attachments thanks
Click to expand...
Click to collapse
dude I have updated the post with the link to downgrade package, by the way thanks for informing
bro by installing pictblack recovery my phone got in a recovery bootloop and internal storgae is not showing ay files help pls
smarty7880 said:
bro by installing pictblack recovery my phone got in a recovery bootloop and internal storgae is not showing ay files help pls
Click to expand...
Click to collapse
Did you flash vbmeta.img ?
does the downgrade firmware supports realme in philippines ? thank you so much sir.
I am at color os v7 I also need to downgrade fast reply will be appreciated
Dar_shan_11 said:
I am at color os v7 I also need to downgrade fast reply will be appreciated
Click to expand...
Click to collapse
Yes, You need to downgrade...
I unlocked my bootloader ..than I installed recovery and after than I installed vbmeta.img
After that I tried to install Havoc Os.
Now I'm stuck at bootloop, can you help me
I must be blind but I can't find the downgrade file in your attachments...
(Edit) Never mind, it's not in the attachments. ^^;
Is there any guide to do it on realms UI?
i have RMX1911ex_11_A.31.
i should follow steps from Unlock Bootloader
correct?
It dœsn't work: my phone just comes back to the fastboot…