[Soft Brick] [Flash Stock] [Recovery] [ADB Driver] Yuphoria [Solution] - YU Yuphoria

Soft Bricking ?
Phone starts and stuck on the Yu logo.
Hard Bricking?
Phone does not start even if the battery is full. Have to go to the service center.
[Note]
1.Make sure that you have 70-80% battery on your phone.
2.You need a PC and a USB cable to connect your phone to the PC.
3.Flashing the factory firmware will wipe all the data present in the internal memory. So, make a backup of that if you can.
[Required Downloads]
1.Download the flash tools.
2. Download the factory firmware (signed fastboot)
3. adb setup drivers.
4. Mirror for drivers manual install here.
5. You can use this tool performs various functions.
# [Install Adb Derives Manually]
1. First of all extract the downloaded file and save it in the computer.
2. Before installation you have to disable the "signature verification" in windows. In windowa 8 or 10 you can do it by going to advanced settings or you can google the way of disabling signature verification.
3. After that turn off the phone and connect it pressing vol up that it will boot in fastboot mode.
4. When you connect the phone go device manager and search for device connected showing error sign.
5. Now click on that device and check for deriver update.
6. Now select the deriver in computer not automatically and select all devices.
7. Now select "have disk"
8. Browse the folder where you had extracted the adb drivers.
9. Now select the drivers file and install.
10. Ignores the Warning and select "always allow"
11. When finished check the device again by connecting to computer in fastboot mode with usb.
# [Flash Factory Firmware]
Steps
1. Extract the flashtools zip in a new folder on the desktop.
2. Extract the factory firmware zip in the same folder and make sure that all of the flashtools files are also present.
3. Now, power off your phone. If you are stuck in a bootloop, then pull out the battery and reinsert it. (Do not switch on the phone.)
4. While pressing the Volume Up key, connect your phone to the PC with the help of a USB cable.
5. You should now see the fastboot logo on your device. If you did, leave the Volume Up key. (If you do not see the logo, retry the process.)
6. Now go to the folder where you extracted the flash tools and factory firmware and run the flash-all.bat by double clicking on it.
7. A command window will open and the flashing procedure will start. (Make sure that your device does not disconnect from your PC during the procedure.)
8. The command window will automatically close once the procedure is completed.
9. Disconnect your device and boot it up by pressing the Power button. The first boot might take around 5-10 minutes to complete.
Congrats!
# [Recovey Installation (Very Easy Method)]
Note
1. Phone must has unlocked bootloader.
2. It must be rooted.
Steps
1. Download the twrp.img file and place it into your phone storage.( you can choose any custom recovery)
2. Now download the app from playstore flashify
3. Now install it and open the app it will require permission for root access, allow the root access.
4. Now open the app and u can backup the current recovery.
5. Now select the "flash" menu and select the "recovry image" and choose the .img file from storage.
6. Then select yes for flashing warning and will says flashing recovery. After completion it will say flash completed.
7. Now select the option button on right top corner and select the reboot into recovery.
8. Now it will reboot into recovery.
Hit "Thanks" if found this thread helpful....​

Thanks for the solution...... it works well !!
Though my yuphoria was working perfectly fine, i wanted to factory reset my mobile for some reasons, which i was not able to do. Both soft and hard custom recovery options were not working (no recovery screen pop up, mobile boots and stuck at YU logo ), tried your solution and it worked.
Just one input for new users like me, where you have asked users to install adb drivers, i tried that part but on running the bat file, the device was not detected, hence had to add yuphoria device drivers from their official site, i am not able to paste the link here but file name is YUPHORIA_drivers-v1.0.zip, also USB debugging option needs to be turned on in developer option for this solution to work.
Rest all steps work exact as you explained.

Sahilsharma said:
Though my yuphoria was working perfectly fine, i wanted to factory reset my mobile for some reasons, which i was not able to do. Both soft and hard custom recovery options were not working (no recovery screen pop up, mobile boots and stuck at YU logo ), tried your solution and it worked.
Just one input for new users like me, where you have asked users to install adb drivers, i tried that part but on running the bat file, the device was not detected, hence had to add yuphoria device drivers from their official site, i am not able to paste the link here but file name is YUPHORIA_drivers-v1.0.zip, also USB debugging option needs to be turned on in developer option for this solution to work.
Rest all steps work exact as you explained.
Click to expand...
Click to collapse
Yup bro its difficult to set bootloader driver for yuphoria. But you can install it manually. But always remember to "disable driver signature verification" before installation and i will update the derivers link for manual installation if you message me the link.

will this work on unlocked bootloader

nickjones1007 said:
will this work on unlocked bootloader
Click to expand...
Click to collapse
"yup"... it will work. There is nothing to do with boot loader. It will flash the stock rom and boot-loader will get locked again. You have to unlock the boot-loader again if you want to flash custom rom again.

And i will get the official ota updates from YU as well ?
Sent from my YU5010 using Tapatalk

nickjones1007 said:
And i will get the official ota updates from YU as well ?
Sent from my YU5010 using Tapatalk
Click to expand...
Click to collapse
yep bro.. you will get the updates and i don't think you know that, there are no restrictions for unlocking/locking boot-loader of YU mobile. I mean the warranty not void if you unlock the boot-loader.

Thnx a lot bro and yeah i knw that ... Actually i'm gonna start installing roms so in case if it goes wrong i just a needed reliable method to get back on stock company's software ....
Thnx again bro
Sent from my YU5010 using Tapatalk

nickjones1007 said:
Thnx a lot bro and yeah i knw that ... Actually i'm gonna start installing roms so in case if it goes wrong i just a needed reliable method to get back on stock company's software ....
Thnx again bro
Sent from my YU5010 using Tapatalk
Click to expand...
Click to collapse
its reliable bro and worked for me when i screwed my phone. But note one thing that you should have installed the adb drivers properly on your computer. Anyway if u screwed up don't hesitate to discuss here.

When i start the flashall.bat the phone restarts and stuck back at the cyanogen logo..!

goudaniket said:
When i start the flashall.bat the phone restarts and stuck back at the cyanogen logo..!
Click to expand...
Click to collapse
Is driver properly installed? Or retry to download setup again if you have done right then
1. boot into bootloader
2. run bat file it will take some time. If all goes well then it will say about relocking of boot-loader.
3. seletct yes and restart.
4. you will see yu logo and it will take 10-15 minutes to load so stay calm! If it doesn't load then try again.

awesome... worked for me

maazkazi91 said:
awesome... worked for me
Click to expand...
Click to collapse
You can simply hit the thanks buttton bro

Can u remember me?

I can't root my YU 5010a

ankityu said:
I can't root my YU 5010a
Click to expand...
Click to collapse
I think you have issue with adb driver .. Is that resolved?

No man
...its still stuck in there..

ankityu said:
No man
...its still stuck in there..
Click to expand...
Click to collapse
Bro i hv updated the thread with steps to install adb drivers. Try it and then report if it works.

What is signed fastboot

ankityu said:
What is signed fastboot
Click to expand...
Click to collapse
Install it . these are the drivers.

Related

Leagoo Lead 3 root

I got root on my Leagoo Lead 3 using the following method a user had for his Leagoo Lead 1.
http://forum.xda-developers.com/showpost.php?p=54321112&postcount=3
Edit: skip the first step and only proceed to step two. Your device will try to boot into fastboot once or twice. When that's done, open mtk uncle tools on your device and then head into engineering mode and click root in the user/root menu.
Hope this helps anyone who needs root.
Root failed for me
Hi rukusx7
In my case it has failed... can you help me, please?
My phone had installed X applications, google account... prior to root...
Fisrt Step: Bootloader unlock...finish OK
When I run button of Bootloader unlock my mobile init in mode fastboot, make tasks and finish ok and mobile still in fastboot mode​
Next Step: KingoRoot.... finish Failed.
When I run kingoroot, my mobile is in mode fastboot ¿it's ok?...make tasks and after a long time finish with failed​My sencond attempt is to run kingroot with my mobile ON as usual but kingoroot failed too..​
I think my problem is the step 1. How can I check the step 1 is correct?
Thanks in advanced for your help.
I really messed up with explaining myself on that. I really have NO idea how any of that root guide worked for me.... I completely omitted the first step. I'm truly sorry if my misinformation has caused you any troubles.
Start sony bootloader unlocker and run it with your phone connected.
It will restart your phone to fastboot and then it remains idle.
Keep your phone plugged in, switch it off and boot manually into the fastboot (power + vol up)
From here the unlocker will proceed unlocking.
Step 1 done.
Click to expand...
Click to collapse
This is the only part of the tutorial I followed.
Now open kingosoft root connect the phone and let it do its thing.
At restart of the phone kingosoft will show on screen a message like "checking root status"
Launch mtk uncle and enter engineer mode.
Go to log and debugging tab ans select user2root
Select Root.
Now kingosoft will tell you that root is succesfull and restarts the phone.
Click to expand...
Click to collapse
I'm not even sure the bootloader is locked at all....
Hi.
Don`t worry ... just has not been rooted (failed with Kingoroot and Vroot (this app say Yes but really isn`t rooted..),
My mobile is ok
Regards.
root
Hi
I also have Leagoo Lead 3 and i successfully rooted the phone. First step finished OK, but on second step with Kingo Android Root i had a problem
At restart of the phone kingosoft will show on screen a message like "checking root status"
Launch mtk uncle and enter engineer mode.
Go to log and debugging tab ans select user2root
Select Root.
Now kingosoft will tell you that root is succesfull and restarts the phone.
Click to expand...
Click to collapse
I selected root but nothing happened, it continued to say "checking root status", "connecting to device" and it took lot of time so i closed the program to start again but then i had another problem. It didn't want to connect with device, it tried and tried but without success.
-- my steps --
- When i started Kingo Android Root for first time it downloaded HTC driver so i downloaded latest driver HTCDriver_4.2.0.001.exe ( [DRIVERS] Latest HTC Drivers [4.2.0.001] )
- I rebooted the PC ( now i don't have unknown device in Device Manager)
- On phone launch MTK Uncle and select User (on my phone it is = ENGINEER MODE/ENGINEER MODE (MTK)/LOG AND DEBUGGING/USER2ROOT/USER)
- Go to Settings / Developer Options and turn on USB Debugging (if it is already turned on, turn it off and then turn it on again)
- Start Kingo Android Root, connect phone to PC ( try to use usb cable that came with mobile phone ) and do everything like in step 2
Now open kingosoft root connect the phone and let it do its thing.
At restart of the phone kingosoft will show on screen a message like "checking root status"
Launch mtk uncle and enter engineer mode.
Go to log and debugging tab ans select user2root
Select Root.
Now kingosoft will tell you that root is succesfull and restarts the phone.
Click to expand...
Click to collapse
If it cant establish connection with phone try to reboot the phone ( don't unplug the phone from PC ) and when it reboots, check again if USB Debugging is turn ON.
I rooted my phone at second attempt but that doesn't means that it would work for everybody or that this steps are needed.
Yeah, it took me a few attempts to be honest. I also used a data cable from my oneplus one.
I'm happy there are more people to help with this, so we can get some proper root instructions.
Also new firmware is on their site. I know nothing about mtk devices. How can I flash it if I can't find how to get into fastboot mode manually? (Why I omitted first step)
Edit: Quick Reboot from playstore will boot into fastboot mode for you!
Sent from my One.....mmmm... bacon.
Leago Lead 3
-- On my phone (when is turned off ) if i press ( vol+ ) and then ( power ) key it will enter recovery but in recovery menu, ( power ) key doesn't work.
I can only go down with ( vol- ) and select with ( vol+ ).
-- If i press ( vol- ) and ( power ) key *(when is turned off)* i will enter something similar to recovery, but everything is on Chinese language.
Here i can go up and down through the menu and select with ( power ) key.
I only know that word at the bottom means EXIT.
I also don't know how to flash, i think we need to use SP Flash Tool or MTKDroidTools but they look complicated.
Successfully installed Carliv custom recovery. You need root first though.
[PORT][RECOVERY] Carliv Touch Recovery v-1.5 for porting to all MTK phones
You need Default [UTIL][WIN][MT65xx] MTK Droid Root & Tools | MediaTek Android Smartphone
I didn't manually do the work. I used the automated porting tool. But to get root shell, I had to run the MTK tools. It notifies you that it can get you root shell by clicking root. Then you run CTRv-1.4 (the automated porting tool) and it can gain root shell access now. It automates everything and boots you into the new CWM.
By this point, if you can get root, you should have everything you need. I installed adb using
[TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.3
I've also semi deciphered the Chinese menu. So from the first menu entry.
1. Testing
2. Testing
3. Testing
4. Testing
5. Test Report
6. WIPE eMMC
7. INFO
8. INFO
9. Reboot
10. Power Off
Just tried out Philz Recovery as well. Works like a charm.
rukusx7 said:
Just tried out Philz Recovery as well. Works like a charm.
Click to expand...
Click to collapse
Do you have a link to the recovery you used?
vampirefo said:
Do you have a link to the recovery you used?
Click to expand...
Click to collapse
A Google search brought this up as the first link.
http://forum.xda-developers.com/showthread.php?t=2201860
You can build your own custom philz with either the recovery.IMG from your own phone or you can choose one manually. Leagoo has updated firmware for this device on their website. I suggest an update first then root and then recovery.
Sent from my One.....mmmm... bacon.
rukusx7 said:
A Google search brought this up as the first link.
http://forum.xda-developers.com/showthread.php?t=2201860
You can build your own custom philz with either the recovery.IMG from your own phone or you can choose one manually. Leagoo has updated firmware for this device on their website. I suggest an update first then root and then recovery.
Sent from my One.....mmmm... bacon.
Click to expand...
Click to collapse
Can you upload the version of phil's recovery you used?
vampirefo said:
Can you upload the version of phil's recovery you used?
Click to expand...
Click to collapse
Try this link instead. I meant to link here earlier, but linked you directly to Philz instead. This link has a Windows app which allows you to make your own philz recovery.
Easy Magic PhilZ Touch Installer for MediaTek Devices ONLY
Unlock failed
I'm stuck at unlocking. Mobile is in fastboot, Fetching Unlock Data (on sony bootloader unlock) but nothing. It's been like this for 40 min. Can you help me with this problem ?
eldar123 said:
I'm stuck at unlocking. Mobile is in fastboot, Fetching Unlock Data (on sony bootloader unlock) but nothing. It's been like this for 40 min. Can you help me with this problem ?
Click to expand...
Click to collapse
No need to unlock bootloader. Install mobile uncle tools from play store to device. Pick your favorite rooting tool. I used kingo root. Run kingo root. The app will try to reboot the phone for some fastbook work, when this fails, it will boot back into android. This is where you open mtk uncle tools, head into MTK engineering mode, scroll right until you see user/root. Tap that to choose root and the rooting tool will continue.
Sent from my One.....mmmm... bacon.
rukusx7 said:
No need to unlock bootloader. Install mobile uncle tools from play store to device. Pick your favorite rooting tool. I used kingo root. Run kingo root. The app will try to reboot the phone for some fastbook work, when this fails, it will boot back into android. This is where you open mtk uncle tools, head into MTK engineering mode, scroll right until you see user/root. Tap that to choose root and the rooting tool will continue.
Sent from my One.....mmmm... bacon.
Click to expand...
Click to collapse
No, didn't help.I've done what you told me and nothing's happening. Any other ideas ?
eldar123 said:
No, didn't help.I've done what you told me and nothing's happening. Any other ideas ?
Click to expand...
Click to collapse
I don't know where to help you. What status is your device in? Are we starting back from scratch?
Sorry my guides are terrible, I just found device easy to root and didn't foresee problem for others. I also did a lot of my own research and imagine you would have too before embarking.
Sent from my One.....mmmm... bacon.
I've uploaded my philz touch I "made". I used Easy Magic Philz Installer for mtk devices to get it done.
philz_touch_6.56.2_lead3.img
You can try flashing with flashify from the playstore, or I used the SP_flash tool. You just uncheck what you dont want to flash.
This is where things get good for you. In philz recovery, you can use the built in tool found in the Advanced Menu to Re-root the system. Once completed, reboot and install supersu from the playstore, it will notify you to install the su binary. Reboot and you should have root. Or at least I did.
I used this method AFTER applying the update on the Leagoo website. Which I highly recommend before ANY updates. all updates go OTA after this release. NO idea if update will work after rooting your device or installing CWM.
For using flashify the phone need to be rooted. I started the process with SP_flash tool and nothing, not even 1 %, it's been like this for hours. I tryed every method for rooting and flashing ROM that I could find on internet. I'm starting to be hopeless. Can you upload me you're backup file. I think that i could put it on SD CARD and restore phone to your backup file.

[Q] systemUI broken?

Hey,
I have a major issue on my HAM7 L09, which runs on 5.1 lollipop, is rooted and has TWRP recovery.
Yesterday I was triyng to install Xposed framwork via TWRP. Okay, that failed. But then, when I rebooted my phone, my softkeys and Statusbar, overall SystemUI, is not working. I tried factory reset which didn't help. Since i did factory reset, i can no longer use adb commands from my computer, because it wont no longer authorize my phone. Even tried to downgrade to B127 to install custom rom after that, but because I have TWRP I cant downgrade. And since adb commands are not working, I cannot flash stock recovery either.
Any help please?
Urgent.
Thank you
Getoo said:
Hey,
I have a major issue on my HAM7 L09, which runs on 5.1 lollipop, is rooted and has TWRP recovery.
Yesterday I was triyng to install Xposed framwork via TWRP. Okay, that failed. But then, when I rebooted my phone, my softkeys and Statusbar, overall SystemUI, is not working. I tried factory reset which didn't help. Since i did factory reset, i can no longer use adb commands from my computer, because it wont no longer authorize my phone. Even tried to downgrade to B127 to install custom rom after that, but because I have TWRP I cant downgrade. And since adb commands are not working, I cannot flash stock recovery either.
Any help please?
Urgent.
Thank you
Click to expand...
Click to collapse
Hey Buddy, i did the same thing you did when twrp came out which was to install xposed. Also got the same issue where aspect's of the phone's UI (Status bar, nav bar, homescreen) were missing. I even did the factory reset via twrp. I was able to get out of it, but it required some focus, patience and lots of rebooting. I don't recall exactly what I did for the first step, butThat being said when you plug you phone to your PC, does your PC still recognize it? (ex.prompt to install Android Hisuite Manager pops-up on your monitor)
- If the answer is yes, with your M7 connected to the PC, enable "Developer Options" (if you haven't done it yet)>then reboot. On next boot>go to Developer's Options again>select "Revoke USB Debugging Authorizations".
-Once done, remove the USB connection from your PC's USB port then place it back in again. Let me know if the "ADB Authorization" screen appears.
Okay, as soon as I get home, I'll try that. Right now I'm using button saviour for softkeys
Sent from my HUAWEI MT7-L09 using XDA Free mobile app
blitzkriegger said:
Hey Buddy, i did the same thing you did when twrp came out which was to install xposed. Also got the same issue where aspect's of the phone's UI (Status bar, nav bar, homescreen) were missing. I even did the factory reset via twrp. I was able to get out of it, but it required some focus, patience and lots of rebooting. I don't recall exactly what I did for the first step, butThat being said when you plug you phone to your PC, does your PC still recognize it? (ex.prompt to install Android Hisuite Manager pops-up on your monitor)
- If the answer is yes, with your M7 connected to the PC, enable "Developer Options" (if you haven't done it yet)>then reboot. On next boot>go to Developer's Options again>select "Revoke USB Debugging Authorizations".
-Once done, remove the USB connection from your PC's USB port then place it back in again. Let me know if the "ADB Authorization" screen appears.
Click to expand...
Click to collapse
Being tring your solution for 4 hours. Sadly it doesn't work. authprization screen wont appear
Getoo said:
Being tring your solution for 4 hours. Sadly it doesn't work. authprization screen wont appear
Click to expand...
Click to collapse
Does your computer recognize your phone?
blitzkriegger said:
Does your computer recognize your phone?
Click to expand...
Click to collapse
yes, it does. I can watch my folders and so on.
Getoo said:
yes, it does. I can watch my folders and so on.
Click to expand...
Click to collapse
Sorry for the late reply Buddy as I'm at work at the moment. Found an easier solution. Make sure your phone is connected to your computer. Also open up the folder where you have your ADB files ans stock lollipop recovery. Open the command prompt within that folder.
Next do the following
1.) Turn off your phone and manually invoke TWRP via physical button combination
2.) Once on TWRP, select "Reboot" then choose "Bootloader".
3.) Once the phone is on bootloader mode, connect your phone to your PC's USB port then switch to your open command prompt and type:
fastboot devices
Your device should then be displayed.
4.) next flash the stock lollipop recovery for L09 via the command:
fastboot flash recovery <recoveryname.img>
5.) Once done flashing execute:
fastboot reboot
6.) Once your phone is back on, you can then use your computer to place the "Transition" update.app either within internal storage (create dload folder within internal memory) or sd card/usb drive. Proceed to do local update or update from usb.
7.) Once your phone has the transition lollipop firmware copy the Kitkat rollback firmware then do the usual drill via local/usb update.
blitzkriegger said:
Sorry for the late reply Buddy as I'm at work at the moment. Found an easier solution. Make sure your phone is connected to your computer. Also open up the folder where you have your ADB files ans stock lollipop recovery. Open the command prompt within that folder.
Next do the following
1.) Turn off your phone and manually invoke TWRP via physical button combination
2.) Once on TWRP, select "Reboot" then choose "Bootloader".
3.) Once the phone is on bootloader mode, connect your phone to your PC's USB port then switch to your open command prompt and type:
fastboot devices
Your device should then be displayed.
4.) next flash the stock lollipop recovery for L09 via the command:
fastboot flash recovery <recoveryname.img>
5.) Once done flashing execute:
fastboot reboot
6.) Once your phone is back on, you can then use your computer to place the "Transition" update.app either within internal storage (create dload folder within internal memory) or sd card/usb drive. Proceed to do local update or update from usb.
7.) Once your phone has the transition lollipop firmware copy the Kitkat rollback firmware then do the usual drill via local/usb update.
Click to expand...
Click to collapse
Holy god, dude you are awsome, it worked. Thank you so much. :angel:

HTC Desire 826... Install TWRP Recovery and Root. (100% Working)

Hello Guys,
Today I am going to assist you on rooting your HTC Desire 826 (All Models).
We will be using the conventional method of rooting i.e. flashing SuperSU through recovery. Just follow my steps carefully
and you will root your device successfully without any mess....
Note : The first TWRP recovery made for this device was not perfect. After installing the recovery the touch wasn't working on some models.....However in this post I have provided the Chinese Mod of that TWRP recovery... This works in all models of HTC Desire 826....Thanks to the Chinese guy whose modified the recovery... Don't worry, the recovery is in English, only installation is Chinese and that to only 2 steps which I will explain in this post.
Alert: I am not responsible for any kind of brick(hard or soft) that your device may suffer during this procedure...This method is full proofed but only when you follow it as mentioned...So proceed at your own risk.
1. Installing all necessary drivers
The first step is to install proper drivers for your device on PC. I would recommend to download and install HTC Sync Manager and connect your device to PC...HTC Sync Manager will automatically install all the required drivers that we need for our process...
You can download it from the below link..
https://www.mediafire.com/?m5xcho7w534p936
2. Download Minimal ADB Tools
Now download the adb tools required for our process from the below link
https://www.mediafire.com/folder/483igl8a45dy2/adb
3. Unlock your Bootloader (Very Important)
This step is must.....You have to unlock your bootloader before proceeding further.....
Warning : Unlocking your bootloader will void your software warranty...Also after unlocking the bootloader, the device will be reset... So do backup all your important data from internal memory to sd card or to pc.
You can use 2 methods to unlock your bootloader..
1. By using kingo bootloader unlock... Download it from here http://www.mediafire.com/download/221m4bgsptnmhgj/HTC_Bootloader_Unlock.exe
Download and install this software... Now Connect your phone to PC....Make sure USB Debugging is enabled on your device...Now open Kingo Bootloader Unlock...The software will automatically detect your device....Click on Unlock...It will unlock your phone's bootloader automatically and you're ready to go.....
2. By using HTC's official unlock method...
If the above method fails then goto http://www.htcdev.com/ and create an account and then follow the steps given there to unlock your bootloader.....
Note : This process includes a step where you need to download adb files....No need to download from there....The link for adb files provided by me are sufficient. Just proceed the steps using those adb files.
Now download SuperSU zip by Chainfire from the below link and place the file in your internal memory
http://www.supersu.com/download
Please download the latest zip file and not the apk file.
Important : Go on the above link and Download the latest flashable zip file otherwise you will suffer a bootloop and your device will be stuck on HTC logo
4. Installing TWRP recovery
After you have successfully unlocked your device's bootloader, u need to install the TWRP recovery.
Download the TWRP recovery from here .... https://www.mediafire.com/?hn2j75fxj6hkj9w
Step 1 : Goto Fasboot USB mode
Connect your device to PC.
Open the adb folder downloaded before. While holding the shift key, right click anywhere on the white space inside the folder...
You will see an option namely - Open command prompt here
Click on that........Now type the following command in the cmd window that opens up...
adb reboot bootloader
This will boot your device to bootloader mode...Make sure it says "bootloader usb" there.
Step 2 : Install TWRP
Now double click and open the twrp file downloaded previously.....A command promt will open up with something written in Chinese... Press Enter twice and the twrp recovery will be pushed to your device.....
Done...You have succesfully installed TWRP recovery on your device.
5. Flashing SuperSU
Now disconnect your device from pc....From "fastboot" mode use the up/down volume button to navigate to "hboot" option and press power button to goto "hboot" menu...From there goto "recovery" option and press power button to enter the recovery menu...
TWRP recovery will open up....
On the first screen you will see a warning....Just ignore that and goto the bottom where its written "Swipe to Allow Modifications" and swipe right.
Now a menu will come up...
Select the first option i.e Install
Now Search the SuperSU.zip file in your internal memory that you downloaded previously and select it.
Recovery will flash the zip file.
Now reboot your device.....
Hurrah! Your device is successfully rooted
Goto App launcher and check if there is SuperSU app there. If yes then your device is succesfully rooted.
To verify whether your device is properly rooted, download the root checker app from play store....
If you have any doubts regarding this post, do post your replies so that I can resolve them.
This thread has been started for HTC Desire 826 Device......
If you have any news or mods regarding this device or any custom ROM, feel free to share with everyone via this post.....
Hit THANKS button if I helped you or if you liked my post.
after instaling supersu ... phone is not booting it is hanging in htc screen
karth83 said:
after instaling supersu ... phone is not booting it is hanging in htc screen
Click to expand...
Click to collapse
got the stock rom back with the help of gsmdevelopers forum
karth83 said:
got the stock rom back with the help of gsmdevelopers forum
Click to expand...
Click to collapse
Now is your phone rooted?
Ishan16 said:
Now is your phone rooted?
Click to expand...
Click to collapse
no it is back to stock. atleast i m happy for phone working
can i borrow acc in htcdev ?
pokemon_2201 said:
can i borrow acc in htcdev ?
Click to expand...
Click to collapse
you can easily create, what happened?
Ishan16 said:
Hello Guys,
Today I am going to assist you on rooting your HTC Desire 826 (All Models).
We will be using the conventional method of rooting i.e. flashing SuperSU through recovery. Just follow my steps carefully
and you will root your device successfully without any mess....
Note : The first TWRP recovery made for this device was not perfect. After installing the recovery the touch wasn't working on some models.....However in this post I have provided the Chinese Mod of that TWRP recovery... This works in all models of HTC Desire 826....Thanks to the Chinese guy whose modified the recovery... Don't worry, the recovery is in English, only installation is Chinese and that to only 2 steps which I will explain in this post.
Alert: I am not responsible for any kind of brick(hard or soft) that your device may suffer during this procedure...This method is full proofed but only when you follow it as mentioned...So proceed at your own risk.
1. Installing all necessary drivers
The first step is to install proper drivers for your device on PC. I would recommend to download and install HTC Sync Manager and connect your device to PC...HTC Sync Manager will automatically install all the required drivers that we need for our process...
You can download it from the below link..
https://www.mediafire.com/?m5xcho7w534p936
2. Download Minimal ADB Tools
Now download the adb tools required for our process from the below link
https://www.mediafire.com/folder/483igl8a45dy2/adb
3. Unlock your Bootloader (Very Important)
This step is must.....You have to unlock your bootloader before proceeding further.....
Warning : Unlocking your bootloader will void your software warranty...Also after unlocking the bootloader, the device will be reset... So do backup all your important data from internal memory to sd card or to pc.
You can use 2 methods to unlock your bootloader..
1. By using kingo bootloader unlock... Download it from here http://www.mediafire.com/download/221m4bgsptnmhgj/HTC_Bootloader_Unlock.exe
Download and install this software... Now Connect your phone to PC....Make sure USB Debugging is enabled on your device...Now open Kingo Bootloader Unlock...The software will automatically detect your device....Click on Unlock...It will unlock your phone's bootloader automatically and you're ready to go.....
2. By using HTC's official unlock method...
If the above method fails then goto http://www.htcdev.com/ and create an account and then follow the steps given there to unlock your bootloader.....
Note : This process includes a step where you need to download adb files....No need to download from there....The link for adb files provided by me are sufficient. Just proceed the steps using those adb files.
Now download SuperSU zip by Chainfire from the below link and place the file in your internal memory
https://www.mediafire.com/?62mm4vg153a8jzf
4. Installing TWRP recovery
After you have successfully unlocked your device's bootloader, u need to install the TWRP recovery.
Download the TWRP recovery from here .... https://www.mediafire.com/?hn2j75fxj6hkj9w
Step 1 : Goto Fasboot USB mode
Connect your device to PC.
Open the adb folder downloaded before. While holding the shift key, right click anywhere on the white space inside the folder...
You will see an option namely - Open command prompt here
Click on that........Now type the following command in the cmd window that opens up...
adb reboot bootloader
This will boot your device to bootloader mode...Make sure it says "bootloader usb" there.
Step 2 : Install TWRP
Now double click and open the twrp file downloaded previously.....A command promt will open up with something written in Chinese... Press Enter twice and the twrp recovery will be pushed to your device.....
Done...You have succesfully installed TWRP recovery on your device.
5. Flashing SuperSU
Now disconnect your device from pc....From "fastboot" mode use the up/down volume button to navigate to "hboot" option and press power button to goto "hboot" menu...From there goto "recovery" option and press power button to enter the recovery menu...
TWRP recovery will open up....
On the first screen you will see a warning....Just ignore that and goto the bottom where its written "Swipe to Allow Modifications" and swipe right.
Now a menu will come up...
Select the first option i.e Install
Now Search the SuperSU.zip file in your internal memory that you downloaded previously and select it.
Recovery will flash the zip file.
Now reboot your device.....
Hurrah! Your device is successfully rooted
Goto App launcher and check if there is SuperSU app there. If yes then your device is succesfully rooted.
To verify whether your device is properly rooted, download the root checker app from play store....
If you have any doubts regarding this post, do post your replies so that I can resolve them.
This thread has been started for HTC Desire 826 Device......
If you have any news or mods regarding this device or any custom ROM, feel free to share with everyone via this post.....
Hit THANKS button if I helped you or if you liked my post.
Click to expand...
Click to collapse
It will work with marshmallow
saifsalee said:
It will work with marshmallow
Click to expand...
Click to collapse
Yes
thanks it`s working fine
Ishan16 said:
Yes
Click to expand...
Click to collapse
yes its working fine just we have to install latest supersu zip file
otherwise it will stuck on boot logo
note
karth83 said:
you can easily create, what happened?
Click to expand...
Click to collapse
I have big trouble to create acc
pokemon_2201 said:
I have big trouble to create acc
Click to expand...
Click to collapse
U have to just create account with your email address. Please explain the actual problem.
what device you have ? HTC D826 Dtul ?
success rate
Dont mind but what is the success rate and if anything happens then what shud i do to install stock ROM plus does it work on marshmellow
---------- Post added at 08:42 PM ---------- Previous post was at 08:37 PM ----------
saifsalee said:
yes its working fine just we have to install latest supersu zip file
otherwise it will stuck on boot logo
Click to expand...
Click to collapse
from where i can get latest supersu zip file
rahuld41 said:
Dont mind but what is the success rate and if anything happens then what shud i do to install stock ROM plus does it work on marshmellow
---------- Post added at 08:42 PM ---------- Previous post was at 08:37 PM ----------
from where i can get latest supersu zip file
Click to expand...
Click to collapse
it works 100%
just follow the link for updated SuperSU zip filee
https://forum.xda-developers.com/showthread.php?t=1538053
Hang on boot screen
karth83 said:
no it is back to stock. atleast i m happy for phone working
Click to expand...
Click to collapse
I got same problem with HTC desire 826 after fleshing supersu plz tel how to restore back
htc desire 826 root problem
karth83 said:
after instaling supersu ... phone is not booting it is hanging in htc screen
Click to expand...
Click to collapse
i have also same problem plz can you help me to solve this issue.
help me could not flash supersu
i Install the twrp and after that when i flash supersu zip file it say sucess but do not install supersu help me i try three times
I tried to root my phone using twrp. after i rooted it using TWRP my phone isnt turning on... its stuck on boot logo (HTC) I cant turn it off ? How can I turn it off ?
Boot loop
After flashing the superSU, I'm stuck in the HTC logo screen. I tried to hard reset the phone to enter the hdboot menu, but I failed, because it gets stuck in the logo screen again!
I'm literally freaking out!
Can you please help me? Neither hard reset nor soft reset is working and I don't know what to do.
please help

Oneplus soft bricked only hang on logo data are most important please guide

hello guys previous night my opo is automatically restart and hang on logo i try to restart several times and leave mobile upto 1 hour but cant succeded.... the condition is set is going to fastboot and recovery and charging also i try wipe cache but still same.... i have very important data inside my opo.... please guide me how i recover my opo or inside data....
oneplus one
variant 64gb
os cyanogen 12
Is it a stock COS ROM?
I suggest you to dirty flash the rom without overwriting /data
So if you flash the zip it's OK but if you flash from fastboot be aware of not flashing userdata_64.img
yes my ROM is stock rom .... what is dirty flash please guide me....
imran72199 said:
yes my ROM is stock rom .... what is dirty flash please guide me....
Click to expand...
Click to collapse
-Is your bootloader unlocked?
-What recovery do you have?
Available signed flashable ROMs: https://forums.oneplus.net/threads/mirrors-for-official-cyanogen-roms-ota-updates.141825/
Find yours or just chose one, and download the signed flashable zip, then copy it to the phone (while in recovery the phone has MTP enabled on the PC) then just flash that ROM from the recovery, this will overwrite system but won't touch data and most likely fix the bootloop.
Before rebooting after flash wipe cache and dalvik just in case.
Next time do a nandroid backup if you have sensible data. I usually don't keep anything important on the phone, everything on google drive.
I don't know my bootloader is locked or unlocked.... when I try to connect phone in recovery and connect USB nothing happen but when I restart phone and set is on onelus logo and attch usb PC recognized as mtp USB device but driver failed....
I don't know my bootloader is locked or unlocked.... when I try to connect phone in recovery and connect USB nothing happen but when I restart phone and set is on onelus logo and attch usb PC recognized as mtp USB device but driver failed....
imran72199 said:
I don't know my bootloader is locked or unlocked.... when I try to connect phone in recovery and connect USB nothing happen but when I restart phone and set is on onelus logo and attch usb PC recognized as mtp USB device but driver failed....
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-one/general/guide-return-opo-to-100-stock-t2826541
Do this.
Mr.Ak said:
https://forum.xda-developers.com/oneplus-one/general/guide-return-opo-to-100-stock-t2826541
Do this.
Click to expand...
Click to collapse
He wants to keep data... So he at least should try my method first.
seanwlk said:
He wants to keep data... So he at least should try my method first.
Click to expand...
Click to collapse
Then reply him about his latest query.
imran72199 said:
I don't know my bootloader is locked or unlocked.... when I try to connect phone in recovery and connect USB nothing happen but when I restart phone and set is on onelus logo and attch usb PC recognized as mtp USB device but driver failed....
Click to expand...
Click to collapse
Which recovery? Stock or twrp? I'm not sure that when you have stock recovery on the phone gets recognized as mtp on the PC.
I can think of adb to push the ROM zip on the PC but if you claim it doesn't get recognized I have no clue. Are you sire you have the google USB drivers installed?
seanwlk said:
Which recovery? Stock or twrp? I'm not sure that when you have stock recovery on the phone gets recognized as mtp on the PC.
I can think of adb to push the ROM zip on the PC but if you claim it doesn't get recognized I have no clue. Are you sire you have the google USB drivers installed?
Click to expand...
Click to collapse
i have cyanogen recovery.... my set is previously rooted with kingoroot..... i dont know what to do which driver should install or which rom should be good for me..... please give me simple method to recover my data from opo..... i dont have twrp recovery installed.... only cyanogen recovery after pressing vol+ vol- and power this are the options under cyanogen recovery.....
reboot system now
apply update
wipe data/factory reset
wipe cache partition
wipe media
reboot to bootloader
power down
view recovery logs
inside apply update
apply from adb
choose from internal storage
imran72199 said:
i have cyanogen recovery.... my set is previously rooted with kingoroot..... i dont know what to do which driver should install or which rom should be good for me..... please give me simple method to recover my data from opo..... i dont have twrp recovery installed.... only cyanogen recovery after pressing vol+ vol- and power this are the options under cyanogen recovery.....
reboot system now
apply update
wipe data/factory reset
wipe cache partition
wipe media
reboot to bootloader
power down
view recovery logs
inside apply update
apply from adb
choose from internal storage
Click to expand...
Click to collapse
Install fastboot,adb and google USB drivers : https://drive.google.com/file/d/0B9fZIF6vzIBzT2ZtZkNSVFI5ZHc/view?usp=drivesdk
Reboot the pc
Download twrp: https://dl.twrp.me/bacon/twrp-3.1.0-0-bacon.img.html
Reboot in fastboot mode.
Open a command prompt on the PC inside the folder where the downloaded recovery is.
-Find the folder (maybe user/Downloads)
-while holding shift mouse right click inside the folder
-select "open command prompt here"
Connect your phone and type in cmd
Code:
fastboot devices
If you're lucky and did everything correctly then your phone should appear and you can continue, if not uninstall the drivers you previously had and kingroot and whatever minitool you used and try again.
Now that the device is visible
Code:
fastboot flash recovery twrp twrp-3.1.0-0-bacon.img
Phone should reboot. Just turn off and boot into recovery and hopefully you'll see twrp.
Now connect the phone to the PC an you should see the mass storage and you'll be able to copy the ROM zip there.
Now just flash the zip of the rom and you're done.
U cannot assure you that it will fix the bootloop but it's your best choice.
In the future:
-Never use kingroot or other ****ty mini tools. CMD and manual flash are always the best choice.
-Do a backup if you are not confident with this kind of stuff.
-Don't keep too much stuff on the phone. Use google drive. And services to save contacts, notes images videos.
seanwlk said:
Install fastboot,adb and google USB drivers : https://drive.google.com/file/d/0B9fZIF6vzIBzT2ZtZkNSVFI5ZHc/view?usp=drivesdk
Reboot the pc
Download twrp: https://dl.twrp.me/bacon/twrp-3.1.0-0-bacon.img.html
Reboot in fastboot mode.
Open a command prompt on the PC inside the folder where the downloaded recovery is.
-Find the folder (maybe user/Downloads)
-while holding shift mouse right click inside the folder
-select "open command prompt here"
Connect your phone and type in cmd
Code:
fastboot devices
If you're lucky and did everything correctly then your phone should appear and you can continue, if not uninstall the drivers you previously had and kingroot and whatever minitool you used and try again.
Now that the device is visible
Code:
fastboot flash recovery twrp twrp-3.1.0-0-bacon.img
Phone should reboot. Just turn off and boot into recovery and hopefully you'll see twrp.
Now connect the phone to the PC an you should see the mass storage and you'll be able to copy the ROM zip there.
Now just flash the zip of the rom and you're done.
U cannot assure you that it will fix the bootloop but it's your best choice.
In the future:
-Never use kingroot or other ****ty mini tools. CMD and manual flash are always the best choice.
-Do a backup if you are not confident with this kind of stuff.
-Don't keep too much stuff on the phone. Use google drive. And services to save contacts, notes images videos.
Click to expand...
Click to collapse
writing recovery failed remote: device not unlocked cannot flash or erase
imran72199 said:
writing recovery failed remote: device not unlocked cannot flash or erase
Click to expand...
Click to collapse
This means your bootloader is still locked so you basically can't do anything. To unlock it you would need to factory reset. So your only option is to try installing the ROM via adb on the cyanogen recovery.
PS
Please don't spam my PM I can read you here I get notifications instantly. Thanks. I want to keep the post public in order to help future users in similar conditions so I'm not going to help you in private if it's not strictly necessary.
oneplus one data recovery
seanwlk said:
This means your bootloader is still locked so you basically can't do anything. To unlock it you would need to factory reset. So your only option is to try installing the ROM via adb on the cyanogen recovery.
PS
Please don't spam my PM I can read you here I get notifications instantly. Thanks. I want to keep the post public in order to help future users in similar conditions so I'm not going to help you in private if it's not strictly necessary.
Click to expand...
Click to collapse
if i try to install rom from adb it will kill my data??
imran72199 said:
if i try to install rom from adb it will kill my data??
Click to expand...
Click to collapse
Try to push the zip from adb to /sdcard and then flash the zip through the recovery (which technically should do it since it's a stock ROM)
This will result in a "dirty flash" which will not delete data.
This is your only option in the current state of your phone, if you had rooted your phone properly without kingroot you would have booloader unlocked an you would've had more options. If this doesn't work you are forced to factory reset. And use this opportunity to unlock bootloader with
Code:
fastboot oem unlock
Which due to security measurements will delete all the data.
Before you going to flash anything using adb or something, do this.....
1. Turn off your phone completely.....
2. Connect the charger and let it charger for 10 minutes
3. While the charger is still connected, press the power button (turn it on)
4. Wait....
If the phone boot normally while the charger is still connected, unplug the charger and waits....if the phone goes back bootloop after a few minutes and hours without charger connected then your problem is a dying battery not software....buy a new battery and once your replace it, it will solved your problem without having to flash anything via adb or recovery...it also can save all your data....
iPusak Gaoq™ said:
Before you going to flash anything using adb or something, do this.....
1. Turn off your phone completely.....
2. Connect the charger and let it charger for 10 minutes
3. While the charger is still connected, press the power button (turn it on)
4. Wait....
If the phone boot normally while the charger is still connected, unplug the charger and waits....if the phone goes back bootloop after a few minutes and hours without charger connected then your problem is a dying battery not software....buy a new battery and once your replace it, it will solved your problem without having to flash anything via adb or recovery...it also can save all your data....
Click to expand...
Click to collapse
battery is ok i try your method but not worked
seanwlk said:
Try to push the zip from adb to /sdcard and then flash the zip through the recovery (which technically should do it since it's a stock ROM)
This will result in a "dirty flash" which will not delete data.
This is your only option in the current state of your phone, if you had rooted your phone properly without kingroot you would have booloader unlocked an you would've had more options. If this doesn't work you are forced to factory reset. And use this opportunity to unlock bootloader with
Code:
fastboot oem unlock
Which due to security measurements will delete all the data.
Click to expand...
Click to collapse
what if i flash ota update file through adb sideload of oxygen os
iPusak Gaoq™ said:
Before you going to flash anything using adb or something, do this.....
1. Turn off your phone completely.....
2. Connect the charger and let it charger for 10 minutes
3. While the charger is still connected, press the power button (turn it on)
4. Wait....
If the phone boot normally while the charger is still connected, unplug the charger and waits....if the phone goes back bootloop after a few minutes and hours without charger connected then your problem is a dying battery not software....buy a new battery and once your replace it, it will solved your problem without having to flash anything via adb or recovery...it also can save all your data....
Click to expand...
Click to collapse
Lolwat?? What kind of sorcery are you talking about.... ? if it was the battery it wouldn't have happend right after he messed with that stuff. Improve your troubleshot skills ? this kind of stuff happened to me insane amount of times and always were able to fix it, in this case the guy is limited by the fact he doesn't have the bootloader unlocked.
imran72199 said:
what if i flash ota update file through adb sideload of oxygen os
Click to expand...
Click to collapse
That depends if you are running oxygen os, you can't flash an OTA of OS that you are currently not running. To dirty flash you have to use the same version or distribution of the OS you are currently running.

After rooting my phone and then again factory resetting it, I cannot access my phone?

I rooted my phone using kingroot and after that to gain some extra space started deleting files.In that course I deleted apps like webview and keyboard too was deleted automatically. After getting annoyed by this kind of problem I took a decision to "reset factory settings". When my phone got reset those missing files were still not there.So after selecting my language when I tried to connect to my Wifi then the keyboard didn't load. I removed the password of the wifi then also it would not move an inch further i.e. it wont connect to network. So,I am kind of stuck her. Cant flash Rom because USB Debugging and OEM are not enabled.
Is there any way out?
Help.
Bhanu Rajput said:
I rooted my phone using kingroot and after that to gain some extra space started deleting files.In that course I deleted apps like webview and keyboard too was deleted automatically. After getting annoyed by this kind of problem I took a decision to "reset factory settings". When my phone got reset those missing files were still not there.So after selecting my language when I tried to connect to my Wifi then the keyboard didn't load. I removed the password of the wifi then also it would not move an inch further i.e. it wont connect to network. So,I am kind of stuck her. Cant flash Rom because USB Debugging and OEM are not enabled.
Is there any way out?
Help.
Click to expand...
Click to collapse
Try to install the stock rom.
debaadak said:
Try to install the stock rom.
Click to expand...
Click to collapse
Can you tell me the steps involved cause I tried doing that.
Bhanu Rajput said:
Can you tell me the steps involved cause I tried doing that.
Click to expand...
Click to collapse
Have you flashed any other ROM yet? Try to flash Resurrection Remix 5.8.3, gapps aroma variant.
https://sourceforge.net/projects/resurrectionremix/files/jalebi/
Please let me know if it helps.
Bhanu Rajput said:
Can you tell me the steps involved cause I tried doing that.
Click to expand...
Click to collapse
Goto website www.firmwarefile.com
Select Your Phone
Download file Version 1
Extract using 7zip
Install drivers and ets tool.
Read instructions in readme.txt
Flash using ets tool.
Done
Don't root again with Kingoroot
Use adb commands for unlocking bootloader (Note: unlocking bootloader is a necessary step) and install custom recovery ex. Twrp
Flash SuperSU.zip ( download it from official website)
Now your phone is rooted properly.
You can flash kernel,roms, modules etc through twrp.
See XDA for full rooting guidelines
Hit thanks if you resolved it with this way.
A problem in this method.
nischait said:
Goto website
Select Your Phone
Download file Version 1
Extract using 7zip
Install drivers and ets tool.
Read instructions in readme.txt
Flash using ets tool.
Done
Don't root again with Kingoroot
Use adb commands for unlocking bootloader (Note: unlocking bootloader is a necessary step) and install custom recovery ex. Twrp
Flash SuperSU.zip ( download it from official website)
Now your phone is rooted properly.
You can flash kernel,roms, modules etc through twrp.
See XDA for full rooting guidelines
Hit thanks if you resolved it with this way.
Click to expand...
Click to collapse
Okay so what problem I am facing is that I don't have my USB debugging on and I also can't switch it on because I can't enter settings bypassing the staring screen. And I can bypass them because I dont have webview& keyboard apps installed.
Is there any method in which there is no need to switch any thing on from the phone.
And yes my laptop is connecting to my phone. I made that sure.
I also did fastboot but under adb devices my device is not listed.
Bhanu Rajput said:
Okay so what problem I am facing is that I don't have my USB debugging on and I also can't switch it on because I can't enter settings bypassing the staring screen. And I can bypass them because I dont have webview& keyboard apps installed.
Is there any method in which there is no need to switch any thing on from the phone.
And yes my laptop is connecting to my phone. I made that sure.
I also did fastboot but under adb devices my device is not listed.
Click to expand...
Click to collapse
Your device must be shown in device manager. Make sure it is in device manager. Try to install adb drivers from another site.
See device manager and tell me when you connects your device what happens ( Your device shown as )
I send you guide for flashing stock ROM in your phone.
First download and then install all drivers without attaching phone.
If not done try to remove all older installations and then again install drivers from given Firmware folder.
I checked it when I install drivers it shows potential harmful for my PC on windows 7.
Then click it install anyways
After 2-3 retires drivers installed properly.

Categories

Resources