[Q]Stuck in download mode - Galaxy Note 10.1 Q&A, Help & Troubleshooting

Please help me i have restarted my tab GT-N800) and the samsung sign kept rotaing.
I Factory restarted it but no good .
Then i put it in download mode and tried to flash it but it is stuck in SetupConnection
Now it is stuck in download mode when i click Power + Volume up button only the android sign comes the odin mode information does not come
Please Help me :crying:

What about this?
:good:
AthulVincent said:
Please help me i have restarted my tab GT-N800) and the samsung sign kept rotaing.
I Factory restarted it but no good .
Then i put it in download mode and tried to flash it but it is stuck in SetupConnection
Now it is stuck in download mode when i click Power + Volume up button only the android sign comes the odin mode information does not come
Please Help me :crying:
Click to expand...
Click to collapse
1. At the downloading screen, plug your phone into your computer
2. Run Odin (I used Odin3 v3.09)
3. Uncheck auto reboot and F. Reset Time
4. Select PIT and load a .pit file ( Search forum for right PIT file)
5. Click Start
It will fail and your Message box will look like this
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
6. Now uplug your phone from the computer and reboot.
The only explanation I can come up with is that the partition file info gets corrupted or lost and doing this either rewrites the partition info file or tells the system where to look for it. I could be wrong but it is the only thing that works for me.
Wish you luck! Peter :fingers-crossed:

This should be a sticky, thanks my tablet is working again. Thank you Tanker32
Sent from my SM-N900 using Tapatalk

Related

Odin got stuck at initialization step

Hi,
I am a newbie and follow steps carefully to flash rom on my droid charge. I am using Odin 1.82 and CI510_VZW_EP1F_ALL_ONE-LTE-CP_REV3_user_CL300919_Rooted_Debloated.tar.md5 file. I am stucking at initialization step. Would you please give me advice? Thanks a lot.
vnt4356 said:
Hi,
I am a newbie and follow steps carefully to flash rom on my droid charge. I am using Odin 1.82 and CI510_VZW_EP1F_ALL_ONE-LTE-CP_REV3_user_CL300919_Rooted_Debloated.tar.md5 file. I am stucking at initialization step. Would you please give me advice? Thanks a lot.
Click to expand...
Click to collapse
Remove the battery before you go into download mode and put it back in once Odin recognizes your phone.
Yeah I got stuck there too...putting the battery back in worked wonders!
Yeah, it worked like a charm. Thanks for your help. Finally, I have my custom rom on my droid charge.
What do you do it f you have a devise that doesn't have a removable battery?
hi guys i have the same problem with sm-n900 note 3 but removing the battery does nothing please help me out
hazard209 said:
Remove the battery before you go into download mode and put it back in once Odin recognizes your phone.
Click to expand...
Click to collapse
my phone wont recognize it. how can I fix it. help me please
Sorry to hear that. Could you try using a different USB cable or PORT? Let the phone be connected in Odin mode and remove the battery. Wait for 2 - 5 minutes and assemble the battery again.
hazard209 said:
Remove the battery before you go into download mode and put it back in once Odin recognizes your phone.
Click to expand...
Click to collapse
i dont know exactly what you mean. I have a t399 that i´m trying to flash but if i withdraw the battery it won´t get recognized by the pc. please can you be a little more especific i´d be really grateful.
guys please help ??? when i try to flash stock rom on my device (samsung GT-S7582) odin stuck at Initialzation and i get this message :
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
i tried to set pit file but still get the same error !! what should i do
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
guys its stuck on this please help

[Q] Galaxy Exhilarate stuck during emergency recovery

First off, I am a complete Android/PC noob (have used solely apple products until this phone, and an Acer aspire comp. i got 2 weeks ago).
I have been using the Exhilarate with android GB, and wanted to upgrade to ICS. I downloaded Samsung Kies, backed up my phone, and began the firmware upgrade, however once the progress reached 70%-80%, the device came unplugged. after restarting the phone, it is stuck on a screen that says:
upper left corner of screen:
Odin Mode
Product Name:SGH-I577
Custom Binary Download: YES(2 counts)
Current Binary: Custom
Center of screen:
Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again.
When I reconnect and attempt to do the emergency firmware recovery using kies, it completes the downloading of the file for firmware emergency recovery, but once it moves on to "proceed to firmware emergency recovery", it stops working (the progress bar is stuck at 0%)
After waiting a little while, the emergency recovery closes, and a message shows saying:
Notice-F PC failed to recognize the mobile phone. Please follow the guide shown below to try again
I gave up on kies, and did some searching of my own. I downloaded the latest version of Odin, as well as the Clockworkmod-Blaze-4G.tar. I made sure there was nothing Kies-related running on my computer, opened up Odin, loaded the clockwork .tar, turned the phone on into download mode (it says Warning!, asks if I want to go into download mode, and then returns to the Odin Mode screen once I say yes). the device is shown as added to odin, I clicked start, and it seemed to be working, and then a big red FAIL appeared in the top left box, and the message box said:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have tried re-installing drivers, different versions of the .tar file (i think they are diff. versions, but not completely sure) rebooting the device many many times, among other things. If anyone has any idea of where to go from here, i would be EXTREMELY grateful.
thank you guys
One more thing
OP here still:
I tried again with a different version of Odin. this time it failed once again, but got a bit further. (everything else was the same):
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
also, I have only checked the Auto reboot box in odin. All others were left blank
I am having a very similar problem with my SGS3 - were you able to solve your problem? If so, can you share how you did?

note 10.1 is blocked in booting

hello
I have the Samsung Galaxy Note 10.1 in 8013 16 GO there, exactly.
I intallé anderoid jelly bean 4.1.1 OTA and did not finish the tablet and restart nonstop. I started handling but nothing goes as planned, ODIN said fail Action! and my tablet is in download mode. And when I reboot I have a small andriod man with the percentage bar with the screen that pops by gray bars. suddenly I think I scrub the tablet and I do not really know what
thank you in advance for helping me because odin know my tablet (the tablet comes into download mode and not in recovry mode) it may not complete the installation with the following message:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
3achour said:
hello
I have the Samsung Galaxy Note 10.1 in 8013 16 GO there, exactly.
I intallé anderoid jelly bean 4.1.1 OTA and did not finish the tablet and restart nonstop. I started handling but nothing goes as planned, ODIN said fail Action! and my tablet is in download mode. And when I reboot I have a small andriod man with the percentage bar with the screen that pops by gray bars. suddenly I think I scrub the tablet and I do not really know what
thank you in advance for helping me because odin know my tablet (the tablet comes into download mode and not in recovry mode) it may not complete the installation with the following message:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Re download factory rom and flash again in odin.. . You can also go in the recovery and clear cache and so on.. This will often stop a boot look . But it looks like you have a bad d/load
I'd agree with that.
I find it best to download the roms from Sammobile as they generally provide an MD5 sum you can check to make sure its not a bad download. Especially when using ODIN 4.03/07... ODIN 4.03 does the check before it flashes and ODIN 4.07 checks when the .tar file is selected.
temp
how temp for odin finish their installation
I think it's hang on: "<ID:0/006> NAND Write Start!! "
erica_renee said:
Re download factory rom and flash again in odin.. . You can also go in the recovery and clear cache and so on.. This will often stop a boot look . But it looks like you have a bad d/load
Click to expand...
Click to collapse
I have not access in the recovery mode
3achour said:
how temp for odin finish their installation
I think it's hang on: "<ID:0/006> NAND Write Start!! "
Click to expand...
Click to collapse
odin did not finish the installation process about 2 hours and even post thank you for helping me
You need to download the rom again to see if it's not a corrupted copy. Use a PC to download it from sammobile.com.
If the flash file you are using is corrupt you can flash it til this century ends and it won't work...
If it still doesn't get past nand write then I believe you may need a pit file to repartition your internal memory. THIS IS A VERY DANGEROUS OPERATION. Make sure you have the correct pit file and if possible get it with an MD5 checksum so you know there is nothing wrong with the downloaded file. It MUST be for your device or bricking may occur, it MUST not be corrupted or bricking will occur.
Good luck and remember, you have been warned...

[Q] GT-P1000 not booting after HEIMDALL Failed Flash

Hello everybody.. I'm in trouble I would appreciate your kind assistance.
I was trying to flash my GTAB GT-P1000 Wifi 3G using Heimdall
I followed the instructions I found in this forum. The flash failed and got this message:
Code:
ERROR Partition "primary-boot" does not exist in the specified PIT
Then the TAB shows only a GREY Battery screen and only after I plug it to wall charger.
It no longer gets into the recovery mode or the Download-Mode using the known combination: Holding Power + Volume down.
At first I was scared, but I used another combination: Pressing Power and both of volume buttons - and + then releasing Power button while keeping the volume buttons held.
In the screen there is a small android and a text:
POWER RESET OR UNKNOWN UPLOAD MODE
This trick allowed me to enter into a different Download Mode, and both odin and heimdall detects my device.
Now I don't know what should be the next step.
Please could you tell me what I should do to make my tab alive again? Any hints are welcome.
Hi Guys,
Finally I succeeded at getting it into Download Mode, I run Odin3_v1.7 and tried to flash it with GB_Stock_Safe_v5
But the flash always fails after movinand.mst.
Code:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> factoryfs.rfs
<ID:0/005> movinand.mst
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help me
Sorry I can't be of much help, but this is the galaxy tab 2 forum, you are looking for the galaxy tab 1 forum. Might be more specific help there. Good luck
anonymous724 said:
Sorry I can't be of much help, but this is the galaxy tab 2 forum, you are looking for the galaxy tab 1 forum. Might be more specific help there. Good luck
Click to expand...
Click to collapse
Thanks for the advice

SM-G920I stuck in boot loop, only boots into Download Mode

Hi all,
Long story short, phone got water damage, left in rice for month, tried to boot and it shows Samsung logo and reboots.
Tried several things which I'll list below, never got anywhere and I'd throw the phone back in a drawer and then a few months later I'd take it out and give it another go
Already have replacement but was looking to hopefully get family photos off it (yes I backup everything now)
So i've tried the following different Odin versions:
3.09, 3.10.6 + 3.12.3
I've downloaded my firmware version G920IDVU3FQF5_G920IVNZ3FQF1_VNZ from SamMobile webite and flashed with that.
Still same issue.
After flashing firmware I have also tried the following different versions of TWRP:
twrp-2.8.6.0-zeroflte.img
twrp-2.8.6.1-zeroflte.img
twrp-2.8.6.2-zeroflte.img
twrp-3.1.1-0-zeroflte.img
Still same issue although I do get the red text "recovery is not seandroid enforcing" along side Samsung Logo but reboots as always.
If only I could get into Recovery I could then mount SD and hopefully get access to photos.
Also tried using ADB to push and pull but no go :silly:
Am I missing something stupid?
I do have the pit file for my model but I'm under the impression it re-partitions everything and I'm guessing that would lose all data so I haven't tried that.
Also tried Samsung Smart Switch but it doesn't find the phone as I can only get it in Download Mode.
Any help would be appreciated :good:
alicg said:
Hi all,
Long story short, phone got water damage, left in rice for month, tried to boot and it shows Samsung logo and reboots.
Tried several things which I'll list below, never got anywhere and I'd throw the phone back in a drawer and then a few months later I'd take it out and give it another go
Already have replacement but was looking to hopefully get family photos off it (yes I backup everything now)
So i've tried the following different Odin versions:
3.09, 3.10.6 + 3.12.3
I've downloaded my firmware version G920IDVU3FQF5_G920IVNZ3FQF1_VNZ from SamMobile webite and flashed with that.
Still same issue.
After flashing firmware I have also tried the following different versions of TWRP:
twrp-2.8.6.0-zeroflte.img
twrp-2.8.6.1-zeroflte.img
twrp-2.8.6.2-zeroflte.img
twrp-3.1.1-0-zeroflte.img
Still same issue although I do get the red text "recovery is not seandroid enforcing" along side Samsung Logo but reboots as always.
If only I could get into Recovery I could then mount SD and hopefully get access to photos.
Also tried using ADB to push and pull but no go :silly:
Am I missing something stupid?
I do have the pit file for my model but I'm under the impression it re-partitions everything and I'm guessing that would lose all data so I haven't tried that.
Also tried Samsung Smart Switch but it doesn't find the phone as I can only get it in Download Mode.
Any help would be appreciated :good:
Click to expand...
Click to collapse
Try to flash CF-Auto-Root via Odin then latest TWRP. If you get in TWRP you will be know what to do
rifek4 said:
Try to flash CF-Auto-Root via Odin then latest TWRP. If you get in TWRP you will be know what to do
Click to expand...
Click to collapse
Still no luck after CF-Auto-Root and then latest TWRP....
Tried to flash firmware again.
With Odin v3.10.6 - flashed G920IDVU3FQF5_G920IVNZ3FQF1_G920IDVU3FQF1_HOME.tar.md5
------
<OSM> G920IDVU3FQF5_G920IVNZ3FQF1_G920IDVU3FQF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
-------
Fails about 20% into system.img.
I'll try flashing with different versions of Odin and report back tomorrow! :good:
alicg said:
Still no luck after CF-Auto-Root and then latest TWRP....
Tried to flash firmware again.
With Odin v3.10.6 - flashed G920IDVU3FQF5_G920IVNZ3FQF1_G920IDVU3FQF1_HOME.tar.md5
------
<OSM> G920IDVU3FQF5_G920IVNZ3FQF1_G920IDVU3FQF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
-------
Fails about 20% into system.img.
I'll try flashing with different versions of Odin and report back tomorrow! :good:
Click to expand...
Click to collapse
HERE you got all. Try latest stock firmware which you get via SamFirm. But BTW I don't wish good future for that phone after swimming in water
Used Odin v3.12.7 and flashed latest firmware > CF-Auto-Root > latest TWRP
No difference....still only boots to download mode.
alicg said:
Used Odin v3.12.7 and flashed latest firmware > CF-Auto-Root > latest TWRP
No difference....still only boots to download mode.
Click to expand...
Click to collapse
Try to hold Volume - + Home + Power for 30 sec and when phone restart (when you see Samsung logo) directly switch from Volume - to Volume + but hold also another two buttons, you should get recovery menu.
rifek4 said:
Try to hold Volume - + Home + Power for 30 sec and when phone restart (when you see Samsung logo) directly switch from Volume - to Volume + but hold also another two buttons, you should get recovery menu.
Click to expand...
Click to collapse
Still no recovery, the phone doesn't hold a charge anymore so it could be a motherboard issue too.
Doesn't turn on at all if not plugged into charger or PC. As soon as I plug it in it shows Android logo and reboots instantly.
Holding Volume Up + Power + Home does nothing, phone just keeps rebooting.
Only when I hold Volume Down + Power + Home does it show the warning screen and I can then choose Volume Up to Continue or Down to Cancel and reboot.
Think I've reached the limit with this phone
alicg said:
Still no recovery, the phone doesn't hold a charge anymore so it could be a motherboard issue too.
Doesn't turn on at all if not plugged into charger or PC. As soon as I plug it in it shows Android logo and reboots instantly.
Holding Volume Up + Power + Home does nothing, phone just keeps rebooting.
Only when I hold Volume Down + Power + Home does it show the warning screen and I can then choose Volume Up to Continue or Down to Cancel and reboot.
Think I've reached the limit with this phone
Click to expand...
Click to collapse
You holded phone in rice for a month etc, but while phone were in water battery was still connected to mobo, and that could makes shocks on mobo and now something can be just burned. And every battery after contact with water will don't hold charge as should

Categories

Resources