Introduction:-
Hello Friends .. I have shared you a guide to Flash Jelly Bean 4.2.2 in Xperia M/Dual - C1904/C1905/C2005/C2006 and this guide is very useful for all and as well as for starters too ...
This tool works for lock bootloader and as well as unlock bootloader
Note:-
This firmware is from Xperia M dual but you can use it in your Xperia M single too
If you are facing problems , you can ask in SXDevelopers facebook group !
>>> if you are going to flash in xperia m single then dont wipe cache and data <<<
Disclaimer:-
I'm not taking any responsibility if you brick your device while flashing your device
You are doing this your own risk.
Skip this , If you don't want to soft brick.
Although its tested but if you will play with files in this mod then Its over you.
I Hope you have read this carefully, Now move to next steps :
Requirement :-
Flashtool
ADB Drivers
Firmware
Instructions :-
Step 1 : First of all download this ftf File from here !!
Step 2 :
Download Flashtool from Here !!
Install it on your PC using onscreen instructions.It will create a folder "Flashtool" in your drive(C\Flastool)
Now go to C\Flastool\drivers\flastool-drivers.exe and click on it and install it after marking/checking "xperia p,xperia u,xperia sola drivers" which is below there on the list
Restart your PC
Note: Make sure you have USB debugging on. If not goto setting>developer options> and check USB debugging on
Step 3 : Now place the downloaded ftf file to C:/Flashtool/firmwares/
Step 4 : Now open Flashtool from the Start Menu
Step 5 : Now click on the FLASH icon of the flashtool which is on the left side of the iconic tab(below the 'file' option-it's like a lightning sign).a window will be opened Mode Selector. Check "FlashMode" and press "ok" button.
Step 6 : Now Select the Firware file which you had placed in C:/Flashtool/firmwares/ in Step 3
Step 7 : A Dialogue Box will appear just click on OK
Step 8 : Now the flashtool will prepare files for flashing and then you will be prompted to connect phone in flashmode.
Step 9 :
Now Power Off your phone and wait for 5 Seconds, then Connect your phone to PC using USB cable while pressing volume down button (-) (Make sure you dont release Volume down button until flashtool starts flashing)
Flashtool will start flashing firmware it may take some time.
After flashing flashtool will prompt you to disconnect you phone. Discconet it and power on your phone (It may take some time for the first boot).
Enjoy the Official Jelly Bean
I Hope that this Guide and post helped you
Click to expand...
Click to collapse
Click Here to View OP !!
Related
pls help..!!!!!
i wanted to add the xperia z home screen panels in my xperia miro as posted somehere in this site.it was a simple procedure but me being impatient n a total noob messed it up.i downloaded the home.apk of xperia z and copied it into the directory /system/apps and replaced it with the stock home.apk and forgot to make a backup of the replaced file n even forgot to change permissions to rw-r-r of the new home.apk.now my phone wont boot n it gets stuck in the 'xperia logo'.is my phone bricked?????is there any solution???help pls
rusted_lkr said:
pls help..!!!!!
i wanted to add the xperia z home screen panels in my xperia miro as posted somehere in this site.it was a simple procedure but me being impatient n a total noob messed it up.i downloaded the home.apk of xperia z and copied it into the directory /system/apps and replaced it with the stock home.apk and forgot to make a backup of the replaced file n even forgot to change permissions to rw-r-r of the new home.apk.now my phone wont boot n it gets stuck in the 'xperia logo'.is my phone bricked?????is there any solution???help pls
Click to expand...
Click to collapse
Your best bet would be to flash the stock firmware onto your device using flashtool.
1) Download flashtool from here: http://androxyde.github.io/
2) Download Miro firmware 11.0.A.5.5 from here: https://docs.google.com/file/d/0B_d8uWGbkaetR1ZuSWlUcTNNQVk/edit?pli=1
3) Install flashtool to your computer, keep the install location default to keep things simple.
4) Move the firmware to the flashtool directory. Default path is C:\Flashtool\firmwares
5) Install the device drivers provided with flashtool. Default path is C:\Flashtool\drivers. Install every driver firmware possible.
6) Open flashtool and click the lightning bolt. Select flash mode.
7) In the new window select your Miro firmware what you moved to the firmwares folder. Do NOT change any of the tick boxes as doing so can cause complications. Press okay.
8) Let flashtool prepare the file for flashing. Once it has it will ask you to connect your device in flash mode. To do so plug the large USB end into your computer, remove your phones battery and leave the back off. Connect the small end of the USB cable to your phone and hold the volume DOWN (-) button. Insert the battery. This puts your phone into flash mode.
9) Let flashtool work its magic. It takes about 2-5 minutes to make your phone work again.
10) Enjoy your working phone.
gamer649 said:
Your best bet would be to flash the stock firmware onto your device using flashtool.
1) Download flashtool from here: http://androxyde.github.io/
2) Download Miro firmware 11.0.A.5.5 from here: https://docs.google.com/file/d/0B_d8uWGbkaetR1ZuSWlUcTNNQVk/edit?pli=1
3) Install flashtool to your computer, keep the install location default to keep things simple.
4) Move the firmware to the flashtool directory. Default path is C:\Flashtool\firmwares
5) Install the device drivers provided with flashtool. Default path is C:\Flashtool\drivers. Install every driver firmware possible.
6) Open flashtool and click the lightning bolt. Select flash mode.
7) In the new window select your Miro firmware what you moved to the firmwares folder. Do NOT change any of the tick boxes as doing so can cause complications. Press okay.
8) Let flashtool prepare the file for flashing. Once it has it will ask you to connect your device in flash mode. To do so plug the large USB end into your computer, remove your phones battery and leave the back off. Connect the small end of the USB cable to your phone and hold the volume DOWN (-) button. Insert the battery. This puts your phone into flash mode.
9) Let flashtool work its magic. It takes about 2-5 minutes to make your phone work again.
10) Enjoy your working phone.
Click to expand...
Click to collapse
=====================================
thanks a lot....it worked like a charm
gamer649 said:
Your best bet would be to flash the stock firmware onto your device using flashtool.
1) Download flashtool from here: [
2) Download Miro firmware 11.0.A.5.5 from here:
3) Install flashtool to your computer, keep the install location default to keep things simple.
4) Move the firmware to the flashtool directory. Default path is C:\Flashtool\firmwares
5) Install the device drivers provided with flashtool. Default path is C:\Flashtool\drivers. Install every driver firmware possible.
6) Open flashtool and click the lightning bolt. Select flash mode.
7) In the new window select your Miro firmware what you moved to the firmwares folder. Do NOT change any of the tick boxes as doing so can cause complications. Press okay.
8) Let flashtool prepare the file for flashing. Once it has it will ask you to connect your device in flash mode. To do so plug the large USB end into your computer, remove your phones battery and leave the back off. Connect the small end of the USB cable to your phone and hold the volume DOWN (-) button. Insert the battery. This puts your phone into flash mode.
9) Let flashtool work its magic. It takes about 2-5 minutes to make your phone work again.
10) Enjoy your working phone.
Click to expand...
Click to collapse
Hi the same happened to my phone, but when i try to do that the green led turns up but I get this in the flashtool
16/000/2013 09:00:24 - INFO - <- This level is successfully initialized
16/000/2013 09:00:24 - INFO - Flashtool Version 0.9.12.1 built on 2013-06-04 22:50:00
16/000/2013 09:00:26 - INFO - Device disconnected
16/000/2013 09:00:40 - INFO - Selected ST23i / 11.0.A.5.5 / CE
16/000/2013 09:00:40 - INFO - Preparing files for flashing
16/000/2013 09:00:56 - INFO - Please connect your device into flashmode.
16/001/2013 09:01:16 - INFO - Opening device for R/W
16/001/2013 09:01:16 - INFO - Start Flashing
16/001/2013 09:01:16 - INFO - Processing loader.sin
16/001/2013 09:01:16 - INFO - Checking header
16/001/2013 09:01:16 - INFO - Ending flash session
16/001/2013 09:01:16 - ERROR -
16/001/2013 09:01:16 - ERROR - Error flashing. Aborted
16/001/2013 09:01:16 - INFO - Device connected in flash mode
If have CWM installed you can run advanced - fix permissions if your phone's permissions are wrong.
Anyway with your current problem try:
> don't enter flashmode until flashtool asks to to do so.
> redownload stock firmware
> run flashtool as administrator/root
thank u man
gamer649 said:
Your best bet would be to flash the stock firmware onto your device using flashtool.
1) Download flashtool from here: http://androxyde.github.io/
2) Download Miro firmware 11.0.A.5.5 from here: https://docs.google.com/file/d/0B_d8uWGbkaetR1ZuSWlUcTNNQVk/edit?pli=1
3) Install flashtool to your computer, keep the install location default to keep things simple.
4) Move the firmware to the flashtool directory. Default path is C:\Flashtool\firmwares
5) Install the device drivers provided with flashtool. Default path is C:\Flashtool\drivers. Install every driver firmware possible.
6) Open flashtool and click the lightning bolt. Select flash mode.
7) In the new window select your Miro firmware what you moved to the firmwares folder. Do NOT change any of the tick boxes as doing so can cause complications. Press okay.
8) Let flashtool prepare the file for flashing. Once it has it will ask you to connect your device in flash mode. To do so plug the large USB end into your computer, remove your phones battery and leave the back off. Connect the small end of the USB cable to your phone and hold the volume DOWN (-) button. Insert the battery. This puts your phone into flash mode.
9) Let flashtool work its magic. It takes about 2-5 minutes to make your phone work again.
10) Enjoy your working phone.
Click to expand...
Click to collapse
thank you very much man. u really helped me.. thx u very much. hats off
Doesn't detect
Hi, if i follow the steps to get in flash mode, flashtool keeps saying that i must connect him. What now?
Flashplay said:
Hi, if i follow the steps to get in flash mode, flashtool keeps saying that i must connect him. What now?
Click to expand...
Click to collapse
What OS do you use? that hapen to me on Win 8.1, try on 7 it wil work.
xperia miro stuck on cyanogen boot logo while flashinf stock ftf
I m facing the same problem,
xperia miro stuck on cyanogen boot logo while flashing stock ftf with flashtool. Now cyanogen boot logo is revovling but nothing else.
Flashttol say device is coonected in usb debugging off, but i checked usb debugging was ticked in setting. now not able to boot phone. Need your help guys ASAP.
Using Windows 7
Hey,
To recover from your brick:
http://forum.xda-developers.com/showthread.php?t=2631456
Have a nice day!
Sent from a bad phone
It shows You didnt have fastboot drivers
---------- Post added at 04:55 PM ---------- Previous post was at 04:51 PM ----------
Pleass provide Updated links for download , My miro stucks at Xperia logo still no recovery ,
gopinaidu said:
It shows You didnt have fastboot drivers
---------- Post added at 04:55 PM ---------- Previous post was at 04:51 PM ----------
Pleass provide Updated links for download , My miro stucks at Xperia logo still no recovery ,
Click to expand...
Click to collapse
For Flashing Stock ROM fastboot drivers are not required, only flashmode drivers are required which Windows manages to get them easily. I wanted fastboot drivers for my phone which were in Flashtool -> Drivers folder. But the installing always used to fail. After lot of google searches I found out as the drivers were not digitally signed Windows used to block it's install process. If you are having same problem just Google 'How to disable driver signature enforcement in Windows'. It helped for me
to root your xperia z 4.2.2 .244 and 2.67
first download the flash tool from here mediafire gcs[/url]...
2.Step Download Xperia Z C660X 10.3.A.0.423 Kernel d-h.st/1Vz[/url])
Step-3 Download Xperia Z rooting toolkit and extract it into a new folder on the computerd-h.st/1Gp DooMLoRD_Easy-Rooting v 18
Step-4: Xperia Z C660X 10.3.1.A.0.244 kernel d-h.st/Od8
UPDATED FOR xperia z C660x 10.3.1.A.2.67 kernel d-h.st/LVH[/url])
note if ur device running 0.244 then downlad 0.244 kernal
or if ur device running 2.67 then download 2.67 kernel
Step-5: Launch the flashtool by double clicking on the flashtool icon
Note: Those who are first timers, navigate to C:/Flashtool/drivers folder to install Flashtool-drivers. Select and check the box of the device model and Flashmode Drivers such as fast boot,xperia z driver etc
Step-6: Connect the Xperia Z to the computer using USB cable. Ensure all drivers are installed properly
Step-7: Copy the XperiaZ_C660X_KernelOnly_10.3.A.0.423_Ge*neric_NL.ftf and XperiaZ_C660X_KernelOnly_10.3.1.A.0.244_*BE.ftf (OR IF YOUR DEVICE RUNING 10.3.1.A.2.67 ) to the flashtool/firmwares folder on the computer
Step-8: On the flashtool, click on the lighting icon and click flashmode then OK
Step-9: A new windows should appear now. At the right sidebar, check Data, Cache, App slog boxes if you wish to wipe the device before flashing. Uncheck all the boxes to remain the data of the device
Step-10: At source folder, browse and choose XperiaZ_C660X_KernelOnly_10.3.A.0.423_Ge*neric_NL.ftf in the flashtool/firmwares
Step-11: Press flash button to start flashing
Step-12: Follow the prompt instructions
First to unplug the USB cable from the phone to disconnect it from the computer
Power off the phone
Third, enter to Flash Mode on the phone by pressing and holding Volume Down button while connecting the device to the computer using USB cable. The display of the device will still remain blank
Step-13: Monitor the Flashtool on the computer. It should continue to run and flash the XperiaZ_C660X_KernelOnly_10.3.A.0.423_Ge*neric_NL.ftf
Step-14: Wait for some time until the installation process is completed which will be indicated by a message in flashtool saying Flashing finished
Step-15: Reboot the phone
Step-16: Connect the phone to the computer in USB Debugging Mode
Step-17: On the computer, close the flashtool
Step-18: Double click the runme_file extracted from the rooting toolkit (in step-2). This will root the device
Step-19: Once rooting is completed, repeat the similar procedure from step-6 to step-15, using the XperiaZ_C660X_KernelOnly_10.3.1.A.0.244_*BE.ftf. (if ur device runing 10.3.1.A.2.67 then select this )
This will flash back the stock kernel to the device
now you are super user
watch my video on youtube
please send youtube link
here's the video
mtayabkk said:
please send youtube link
Click to expand...
Click to collapse
watch?v=E9fSuTZEBBI
matt hardy said:
watch?v=E9fSuTZEBBI
Click to expand...
Click to collapse
thanks man........
Finally , a noob friendly tutorial to get ROOT and CWM Recovery on Xperia E3 . !
SImple.. Fast.. Easy...
ESPECIALLY FOR MODEL D2202 and D2212.
------------------------------------------------------------------------------------------------------------
--Requirements--
1. JAVA Runtime Machine
2. Flashtool
3. SuperSu[ROOT]
4. Recovery[CWM]
5. Minimal ADB and Fastboot
-----------------------------------------------------------------------------------------------------------
Now, Install 1 , 2 & 5
-----------------------------------------------------------------------------------------------------------
--Procedure--
NOTE:- FACTORY RESET WILL TAKE PLACE -- BACKUP YOUR DATA
POWER OFF your phone
1.BOOTLOADER UNLOCKING
-Go to C:/Flashtool/drivers. Execute flashtool-drivers.exe and install Flashmode & Fastboot drivers.
-Open Flashtool.
-Click on BLU icon.
-Connect phone by usb cable to pc by pressing VOLUME DOWN button.Wait for flashing to get completed.
-Unplug device after new window appears then again plug in holding VOLUME UP button.
-A new window will appear with IMEI number of your device .Copy IMEI number and click on GET UNLOCK .
-Now,Official Sony page of bootloader unlocking will appear on your browser . Select Xperia E3 from the devices list,Enter your email-id in box provided.Now you will receive mail from Sony.
-Check your email and click on link in the mail.You will be redirected . Now paste you IMEI number and proceed by agreeing all terms and conditions .
-A new page will appear with unlock code.
-Copy and paste unlock code in window of Flashtool.And then click on UNLOCK.
-Wait till process gets completed.
-Finally , your phone will reboot.
-DONE.
------------------------------------------------------------------------------------------------------------------------------------
TO CHECK:-Switch off your device, click on BLU, press VOLUME UP button and plug the device to PC, if a window appears with RELOCK button then your BOOTLOADER IS UNLOCKED.!
------------------------------------------------------------------------------------------------------------------------------------
2.INSTALLING RECOVERY[CWM]
-SWITCH OFF DEVICE.
-Go to C:\Program Files\Minimal ADB and Fastboot
-Copy and paste .img file(Recovery)(provided in download link) in this folder.Rename file to boot.img .
-Hold SHIFT and RIGHT CLICK on window ,, then select " Open command window here ".
-in command window type- fastboot flash boot boot.img
-Connect device to PC by holding VOLUME UP button .
-Wait till the process gets completed . Disconnect when command window tells to ...
-SWITCH ON device and keep on clicking VOLUME UP and VOLUME DOWN buttons to boot into RECOVERY.
-DONE.
---------------------------------------------------------------------------------------------------------------------------------------
3.GETTING ROOT[SuperSu]
-Copy paste SuperSu in SD Card or Internal Storage.
-Reboot into Recovery.
-Choose "install zip" .
-Now flash SuperSu.
-Choose "reboot system now" and then select "Yes".
-Done
__________________________________________________________________________________
TO CHECK:-Use ROOT CHECKER application.
___________________________________________________________________________________
DOWNLOADS
1. JAVA Runtime Machine - https://java.com/en/download/
2. Flashtool - http://www.flashtool.net/index.php
3. SuperSu[ROOT] - http://download.chainfire.eu/636/SuperSU/UPDATE-SuperSU-v2.37.zip
4. Recovery[CWM] - https://mega.co.nz/#!5Z93wa6a!qs9_WOPLkJb-HqrKE83lb3s58NT9xvqFKfbMnvRYZa0
5. Minimal ADB and Fastboot - https://drive.google.com/file/d/0B1S0LCuXCnnmOWhnUk1ZWVdQakE/view?pli=1
--------------------------------------------------------------------------------------------------------------------------------------------
CREDITS TO ALL DEVELOPERS WHO BROUGHT ABOVE AMAZING STUFF FOR US.
@Raproid especially
Nice tutorial. Did root before this, but I can say those are the steps required and proved working.
Now, how to achieve working init.d? Tried universal init.d and init.d toggler but none worked for me. Any good guide you can point me?
Thanks again!
Edit:
Really sorry, just found http://forum.xda-developers.com/xperia-e3/help/qa-root-recovery-installation-t2990666, oops.
adneon0 said:
Finally , a noob friendly tutorial to get ROOT and CWM Recovery on Xperia E3 . !
SImple.. Fast.. Easy...
ESPECIALLY FOR MODEL D2202 and D2212.
------------------------------------------------------------------------------------------------------------
--Requirements--
1. JAVA Runtime Machine
2. Flashtool
3. SuperSu[ROOT]
4. Recovery[CWM]
5. Minimal ADB and Fastboot
-----------------------------------------------------------------------------------------------------------
Now, Install 1 , 2 & 5
-----------------------------------------------------------------------------------------------------------
--Procedure--
NOTE:- FACTORY RESET WILL TAKE PLACE -- BACKUP YOUR DATA
POWER OFF your phone
1.BOOTLOADER UNLOCKING
-Go to C:/Flashtool/drivers. Execute flashtool-drivers.exe and install Flashmode & Fastboot drivers.
-Open Flashtool.
-Click on BLU icon.
-Connect phone by usb cable to pc by pressing VOLUME DOWN button.Wait for flashing to get completed.
-Unplug device after new window appears then again plug in holding VOLUME UP button.
-A new window will appear with IMEI number of your device .Copy IMEI number and click on GET UNLOCK .
-Now,Official Sony page of bootloader unlocking will appear on your browser . Select Xperia E3 from the devices list,Enter your email-id in box provided.Now you will receive mail from Sony.
-Check your email and click on link in the mail.You will be redirected . Now paste you IMEI number and proceed by agreeing all terms and conditions .
-A new page will appear with unlock code.
-Copy and paste unlock code in window of Flashtool.And then click on UNLOCK.
-Wait till process gets completed.
-Finally , your phone will reboot.
-DONE.
------------------------------------------------------------------------------------------------------------------------------------
TO CHECK:-Switch off your device, click on BLU, press VOLUME UP button and plug the device to PC, if a window appears with RELOCK button then your BOOTLOADER IS UNLOCKED.!
------------------------------------------------------------------------------------------------------------------------------------
2.INSTALLING RECOVERY[CWM]
-SWITCH OFF DEVICE.
-Go to C:\Program Files\Minimal ADB and Fastboot
-Copy and paste .img file(Recovery)(provided in download link) in this folder.Rename file to boot.img .
-Hold SHIFT and RIGHT CLICK on window ,, then select " Open command window here ".
-in command window type- fastboot flash boot boot.img
-Connect device to PC by holding VOLUME UP button .
-Wait till the process gets completed . Disconnect when command window tells to ...
-SWITCH ON device and keep on clicking VOLUME UP and VOLUME DOWN buttons to boot into RECOVERY.
-DONE.
---------------------------------------------------------------------------------------------------------------------------------------
3.GETTING ROOT[SuperSu]
-Copy paste SuperSu in SD Card or Internal Storage.
-Reboot into Recovery.
-Choose "install zip" .
-Now flash SuperSu.
-Choose "reboot system now" and then select "Yes".
-Done
__________________________________________________________________________________
TO CHECK:-Use ROOT CHECKER application.
___________________________________________________________________________________
DOWNLOADS
1. JAVA Runtime Machine - https://java.com/en/download/
2. Flashtool - http://www.flashtool.net/index.php
3. SuperSu[ROOT] - http://download.chainfire.eu/636/SuperSU/UPDATE-SuperSU-v2.37.zip
4. Recovery[CWM] - https://mega.co.nz/#!5Z93wa6a!qs9_WOPLkJb-HqrKE83lb3s58NT9xvqFKfbMnvRYZa0
5. Minimal ADB and Fastboot - https://drive.google.com/file/d/0B1S0LCuXCnnmOWhnUk1ZWVdQakE/view?pli=1
--------------------------------------------------------------------------------------------------------------------------------------------
CREDITS TO ALL DEVELOPERS WHO BROUGHT ABOVE AMAZING STUFF FOR US.
@Raproid especially
Click to expand...
Click to collapse
Hello, is this method can work with Sony Xperia E4 Dual Sim ?
Thanks.
km211121 said:
Hello, is this method can work with Sony Xperia E4 Dual Sim ?
Thanks.
Click to expand...
Click to collapse
Nope e4 has it,s diffrent kernel.
Sent From My Sony Xperia E3 D2212 using XDA app.
Thanks for this. Got my phone rooted but it was soft bricked as the boot.img file supplied i think is only for the D2212. Im using the single Sim LTE variant and had to get the img file from this post (http://forum.xda-developers.com/showthread.php?t=2964845) in order to get my phone working again.
Thanks again for the work and dead easy instructions. Maybe just add the other boot.img file
RootingE3
Is it important to install custom recovery?...i want to root without installing custom recovery
This method can also unlock the devices who have "Allow Bootloader Unlock: NO" ?
I'm asking because my father has an E3 2203 wiht locked bootloader and I wanted to unlock it but from I've read there's no way to unlock a locked bootloader.
Can anyone please confirm that this works?
Thank you in advance.
AlexVat said:
This method can also unlock the devices who have "Allow Bootloader Unlock: NO" ?
I'm asking because my father has an E3 2203 wiht locked bootloader and I wanted to unlock it but from I've read there's no way to unlock a locked bootloader.
Can anyone please confirm that this works?
Thank you in advance.
Click to expand...
Click to collapse
this method can not unlock devices which are not allowed to be unlocked..
mean =>"Allow Bootloader Unlock: NO" can,t be unlocked.
but maby flashing open device botloader can unlock. because it is a botloader without locked state. i think so.
is this allowed for xperia E3 D2202??? i dont know whats the status on "allowed bootloader unlock"
Showing error Camera common has stopped working !! :/
When I restart my phone !! Error appears say "Camera Common has stopped working" ? It occurs in a loop
No work in E3 /D2206/D2203/D2243 ?
d2203
does this work also on xperia D2203?
after flashing cwm recovery my phone stuck in sony logo what to do??
Can I?
Can I install that cmw recovery with Mobile Uncle tools apk?
I can not download Minimal ADB and Fastboot from Google drive's link. It says "We're sorry. You can't access this item because it is in violation of our Terms of Service."
Anybody, help Me.. please.
adneon0 said:
DOWNLOADS
4. Recovery[CWM] - https://mega.co.nz/#!5Z93wa6a!qs9_WOPLkJb-HqrKE83lb3s58NT9xvqFKfbMnvRYZa0
Click to expand...
Click to collapse
Can I get alternate download link from other file host site
like drop box or drive or devhost or mediafire.
Mega don't open here. The link is down.
Please. :crying:
adneon0 said:
4. Recovery[CWM] - https://mega.co.nz/#!5Z93wa6a!qs9_WOPLkJb-HqrKE83lb3s58NT9xvqFKfbMnvRYZa0
Click to expand...
Click to collapse
This link does not open
yashgumaste said:
This link does not open
Click to expand...
Click to collapse
Você sabe como instalar o modo recovery no xperia e3 2043 ?
hello im new
i have xperia e3 d2202
i tried flashing but fails,, my phone wasnt recognized in my pc (The LED lights Green but nothing happens).
The phone connects in Fastboot(with blue LED) and is recognized in Flashtool
can u help me ?
dilshadpk96 said:
Is it important to install custom recovery?...i want to root without installing custom recovery
Click to expand...
Click to collapse
Then you can use the apps like kingroot for android,etc.
---------- Post added at 02:55 PM ---------- Previous post was at 02:51 PM ----------
luci morningstar said:
hello im new
i have xperia e3 d2202
i tried flashing but fails,, my phone wasnt recognized in my pc (The LED lights Green but nothing happens).
The phone connects in Fastboot(with blue LED) and is recognized in Flashtool
can u help me ?
Click to expand...
Click to collapse
I think you should use opposite volume key to that u are using now,same thing occured with me, the posts said volume down key but in my Xperia e3 dual D2212 it worked with up volume key,so you can try that
---------- Post added at 03:00 PM ---------- Previous post was at 02:55 PM ----------
yashgumaste said:
Can I get alternate download link from other file host site
like drop box or drive or devhost or mediafire.
Mega don't open here. The link is down.
Please. :crying:
Click to expand...
Click to collapse
Yess recovery's link is also down,the file is not available on megafire
While trying some mods for Unite 2 , my phone got bricked, i must have done something wrong because those mods are working for others. so it was completely my mistake. so i spent my last 4 hours trying to find a solution and this is how i finally got it work.
JUST WANT TO REMIND YOU THAT TRY THIS GUIDE ON YOUR ON RISK, IM NOT GIVING YOU ANY GUARANTEE THAT IT WILL GOING UNBRICK YOUR DEVICE, IM JUST SHARING THE METHOD WHICH WORKED FOR ME
MY DEVICE
MICROMAX UNITE 2 4GB
KITKAT 4.4.2
following was the symptoms of my device only try this guide if yours are identical to mine
Phone was not booting up (nothing was happening no matter how long i press power button)
wasn't booting into to recovery mode also notification led was not turning on when plugged to PC (i.e No charging)
windows was making device plugged and unplugged sound over and over again when i was connecting it to pc using data cable
now from the 3rd point i figured out that my phone was being detected by my pc but only for a brief moment
so after searching for a while i found out that it was a problem with the PRELOADER and device was trying load META mode(donAt have any clue what that is) so i needed to Install MTK65XX Preloader USB Vcom Drivers for SP Flash Tools.
this is how i did it
Step 1 :Firstly Download MTK USB VCOM Drivers from here
DOWNLOAD
the extract it
Step 2 : Now open Device Manager in your PC by right clicking on My Computer and then click on Manage.
Step 3 :Next go to Device Manager in that and click on your PC name and then click on Add legacy hardware, see below
Step 4 : Now in Add Hardware Wizard click on Next >> Install the Hardware that i manually select from a list (Advanced) >> Show All Devices >> Next >>Have a Disk >> Browse, Now select the inf file according to your OS and from where you extracted the downloaded drivers.
Step 5 : Now click on Next on the wizard to install the drivers and when promoted for security issue just click on install any anyway to finish the driver installation.
Step 6 : After installation finish restart your PC.
Source
now remove battery of your phone and then plug it to your pc using data cable While Holding Volume up button
the windows will recognize it and install drivers, now open device manager and if you find a device under Ports(Com&LPT) which has Mediatek, MTK, USB, VCOM,PRELOADER keywords in it then you are good to go
now download SP Flash Tool
Devhost l Mediafire
and Factory rom
Download
and then extract the Factory rom archive
Then flash Stock ROM by following these steps:
Step 1: Open SP flash tool and load the Scatter file of Stock ROM it is inside the extracted factory rom folder
Step 2: Select Format all+Download in drop-down menu.
Step 3:Remove the battery of your phone.
Step 4:Click Download in SP Flash Tool.
Step 5:connect your phone to pc via USB cable while holding volume up button you can release volume button when the process is stared . Wait for flashing to complete .
Step 6: when the process is completed unplug the phone, insert the battery and then turn it one hopefully it should boot now and you should see Micromax logo just remember first boot take long time so just wait for it to completely boot
if this doesn't work then don't loose hope keep on searching for other ways ,
Nice one.... Will be helpful for some
How To Flash Idea Alcatel One Touch 5036D done by Smart Phone Help
flash tool https://spflashtools.com/windows/sp-flash-tool-v5-1812
Firmware 1: http://infopade.com/4sSA
Password: touch
if the above firmware doesn't work for you, try this
Firmware 2: http://infopade.com/4sWN
Password - Gsmtel.in
like video: https://youtu.be/lwN-BLvenEo
Thanks for watching, & please remember to Like this video, if it helped you. I will answer all comments below,
Be sure to share with your friends. !!
Please Reply Me For More Future Videos !!
Once Again, Thanks For Watching Subscribe for more future videos
Steps:
- Step 1: Download and Install the android USB drivers on your computer. In case you have already installed them, you can skip this step.
Step 2: Switch off you Android Phone .
Step 3: Now download the stock ROM or the custom ROM which you want to install on your phone. After downloading, extract the zip file on you system.
Step 4: Download the SP Flash Tool on your system and extract the downloaded zip file on your system. After that you can see the following files listed.
Step 5: Form the files listed run the Flash_tool.exe file.
Step 6: Once the SP Flash tool is started, click on the Scatter-Loading button located in the right side.
Step 7: Now locate the scatter file in your custom or stock ROM. It is generally located in the bin/directory.
Step 8: Now click the Download button to start the downloading process.
Step 9: After completed all the above steps, connect your smart phone to your system using the USB cable and press any button other than power button so that your system will detect your device. You can use volume buttons.
Step 10: Once the flashing process is completed, a green ring will appear on your system. Now disconnect your device and switch it ON.
Requirements:- Your phone must have atleast 40-50% of battery and USB Drivers