This is How i unbricked my Unite 2(4GB)

This is How i unbricked my Unite 2(4GB) - Micromax A106 Unite 2

While trying some mods for Unite 2 , my phone got bricked, i must have done something wrong because those mods are working for others. so it was completely my mistake. so i spent my last 4 hours trying to find a solution and this is how i finally got it work.
JUST WANT TO REMIND YOU THAT TRY THIS GUIDE ON YOUR ON RISK, IM NOT GIVING YOU ANY GUARANTEE THAT IT WILL GOING UNBRICK YOUR DEVICE, IM JUST SHARING THE METHOD WHICH WORKED FOR ME
MY DEVICE
MICROMAX UNITE 2 4GB
KITKAT 4.4.2
following was the symptoms of my device only try this guide if yours are identical to mine
Phone was not booting up (nothing was happening no matter how long i press power button)
wasn't booting into to recovery mode also notification led was not turning on when plugged to PC (i.e No charging)
windows was making device plugged and unplugged sound over and over again when i was connecting it to pc using data cable
now from the 3rd point i figured out that my phone was being detected by my pc but only for a brief moment
so after searching for a while i found out that it was a problem with the PRELOADER and device was trying load META mode(donAt have any clue what that is) so i needed to Install MTK65XX Preloader USB Vcom Drivers for SP Flash Tools.
this is how i did it
Step 1 :Firstly Download MTK USB VCOM Drivers from here
DOWNLOAD
the extract it
Step 2 : Now open Device Manager in your PC by right clicking on My Computer and then click on Manage.
Step 3 :Next go to Device Manager in that and click on your PC name and then click on Add legacy hardware, see below
Step 4 : Now in Add Hardware Wizard click on Next >> Install the Hardware that i manually select from a list (Advanced) >> Show All Devices >> Next >>Have a Disk >> Browse, Now select the inf file according to your OS and from where you extracted the downloaded drivers.
Step 5 : Now click on Next on the wizard to install the drivers and when promoted for security issue just click on install any anyway to finish the driver installation.
Step 6 : After installation finish restart your PC.
Source
now remove battery of your phone and then plug it to your pc using data cable While Holding Volume up button
the windows will recognize it and install drivers, now open device manager and if you find a device under Ports(Com&LPT) which has Mediatek, MTK, USB, VCOM,PRELOADER keywords in it then you are good to go
now download SP Flash Tool
Devhost l Mediafire
and Factory rom
Download
and then extract the Factory rom archive
Then flash Stock ROM by following these steps:
Step 1: Open SP flash tool and load the Scatter file of Stock ROM it is inside the extracted factory rom folder
Step 2: Select Format all+Download in drop-down menu.
Step 3:Remove the battery of your phone.
Step 4:Click Download in SP Flash Tool.
Step 5:connect your phone to pc via USB cable while holding volume up button you can release volume button when the process is stared . Wait for flashing to complete .
Step 6: when the process is completed unplug the phone, insert the battery and then turn it one hopefully it should boot now and you should see Micromax logo just remember first boot take long time so just wait for it to completely boot
if this doesn't work then don't loose hope keep on searching for other ways ,

Nice one.... Will be helpful for some

Related

[How to/MTK65xx] ROOT, Backup & Flash (MTKDroidTools, Spflashtool, CWM) [MTK Only]

[How to/MTK65xx] ROOT, Backup & Flash (MTKDroidTools, Spflashtool, CWM) [MTK Only]
Hi
This is a guide to ROOT, backup and flash your MTK65xx or Other device (Supported devices: http://forum.xda-developers.com/apps/framaroot/framaroot-supported-devices-t2722980 all credits to alephzain) written by s7yler.
More guides & reviews on my Youtubechannel http://www.Youtube.com/s7yler and http://s7yler.blogspot.com
(Tools used are Framaroot, MTKDroidtools/CWM and SpflashTool)
I will try to write this guide in step by step, so everyone can understand it. This is for PC and will work with Windows 7.
-> All is done by your own risk! this is just a guide to help people with the tools and process. <-
How to ROOT the phone first
1. Get the latest Framaroot apk here http://forum.xda-developers.com/apps/framaroot/root-framaroot-one-click-apk-to-root-t2130276
2. Download it and install it on the phone, open the Framaroot app on the phone.
3. Let it be on Install SuperSU, and try the last method, if that dont work, then try one of the 2 others.
4. Then it should say success root, and now reboot the phone.
5. After reboot the phone should be ROOTED, download root checker from the Play store and verify that your rooted.
How to make a simple backup (not completly 1:1) of your stock ROM / MTK phone
1. You have you brand new MTK phone.
2. What I do first is to install all possible drivers. So you go to your PC and install these apps/drivers:
Snappea - http://www.snappea.com/windows
Pdanet drivers - http://pdanet.co/a/ (When it ask what device you have in the install process, just say "Other")
Mediatek Preloader USB VCOM Drivers - (Install file) http://www.mediafire.com/download/cypm22rgs2k83ji/MT6577+USB+VCOM+drivers.rar and here the raw drivers http://www.magicdriver.com/driver4214-ver_1.1123.0.html
For the Preloader VCOM drivers for Windows 8 please read here, and follow this:
http://thebroodle.com/android/install-mediatek-mt65xx-usb-vcom-drivers-windows-8-8-1/
3. On your MTK phone you must in "Developer Options" enable "USB debugging mode".
4. Now download MTK Droid Tools here http://forum.xda-developers.com/showpost.php?p=49597819&postcount=922
5. Start MTK Droid Tools, and connect your phone with the USB cable to the PC. (if Windows install some drivers, then let it install them automatically).
6. Now on the first page of MTK Droid Tools, it should display all infos about the phone when you connect it.
7. If the sqare is Green, then you have root shell and ready, if its not green, press the ROOT button to the right in MTK Droid tools.
8. Click the "IMEI/NVRAM" button and then Backup to backup your IMEI/NVRAM, the backup files will be inside of the MTK Droid Tools folder.
Also you can manually write down your IMEI number just in case it should be lost.
9. Now go to the tap "root, backup, recovery" (in MTK Droid Tools).
10. Click the Backup button, and it will create a complete backup of your ROM. (in the end it will ask, if you want to pack it, just answer no)
11. When it is finished then also click "To prepare blocks for FlashTool", that will convert the backup to be compatible with Spflashtool. (choose the files.md5 inside the backup folder)
12. After the backup is done it will be inside "backup" in the MTK Droid Tools folder. And inside it there will also be a new folder called "!Files_to_FlashTool" Inside there the files for Spflashtool is. So when loading your backup with Spflashtool you must load the scatter file from inside there.
13. Now to install CWM (clockworkmod recovery) In MTK Droidtools, choose "To use boot from phone" and click the "Recovery and Boot" button. It will ask you a lot, just say yes every time, and it will end of sending CWM recovery to the phone and reboot into it on the phone. After you see CWM on the phone you know it is done. You can switch the menu with the volume keys, and the power is the select button.
14. Inside CWM you can also do a complete backup of your phone (remember to have enough space, you can do the backup to the internal storage OR to the SDcard - try "backup" if that fails then choose instead "backup to external sd" or vice versa). I recommed doing that because CWM makes another backup than the one made with MTK Droid Tools. So if you should get problems or loose something, you can always run your CWM backup into your phone and it will be as before.
15. After your done the backup, copy the backup also to a safe place on your PC. Just in case!
16. So now your Rooted, have installed CWM recovery, have a IMEI/NVRAM backup and a backup for Spflash Tools plus CWM backup.
To make a 100% FULL 1:1 (more advanced) ReadBack ROM backup using SP FlashTool please check these guides here, and learn how to:
http://mmx-unite2.blogspot.de/2014/08/how-to-create-readback-backup.html
http://forum.gsmhosting.com/vbb/f60...artphone-how-read-backup-1656510/#post9415324
or here:
http://pinoyscreencast.net/how-to/g...-smartphones-using-spft-mtk-droid-root-tools/
To flash a backup or ROM with Spflashtool:
Disclaimer: Don't flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones you will have a brick even if you download these blocks read from phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM. I take no responsibility for any harm done while attempting this!
1. Go download Spflash tool here http://forum.xda-developers.com/showthread.php?t=1982576
Both version 3 or 5 should be good to use. If your having problems with one of them or they crash, try this newer version here: http://forum.xda-developers.com/showthread.php?t=2650125
2. Disconnect your phone if connected with USB to the PC, and turn OFF the phone completely, also take out the battery if possible (but can also work with the battery inside the phone, for phones with builtin battery).
2. When you now again connect the USB cable to the phone with the PC while the phone is still off, Windows should popup and beginn to install the MTK65XX Preloader Drivers, this only happens if you installed the Mediatek Preloader USB VCOM Drivers correct in Windows. After they successfully installed, disconnect the USB cable again.
2. Start Flash_tool.exe to start the program
3. Now hit the "Scatter-loading" button, and go to the backup or ROM, inside the folder "!Flash files Spflashtool" load the scatter.txt file. (ALWAYS only load a ROM that is 100% made for your phone, flashing a wrong ROM may make your phone non-bootable)
4. When the scatter file is loaded, it will show all the content in the Spflashtool window.
5. If you only need for example to flash the EBR files, you can deselect all the others. But remember that it must be same ROM or backup.
6. Hit the "Download" button in Spflashtool. Then there should be some pink lines with colors showing that it loads the files.
7. When it stopps to flash/load, connect your phone with the USB cable, remember the phone must be OFF (and without the battery inside if possible to remove). If nothing happens then maybe it is necessary to press at the same time with connect of a cable the camera or volume buttons. For example, hold the volume up button down, insert the USB cable, and then insert the battery (still holding the volume up button down) when you hear it connect in Windows and the colored lines begins to move, let go off the volume up button.
8. Now it should connect (maybe Windows install some drivers by now - the MTK65xx Preloader drivers) and it will in the end continue to flash in Spflashtool when the phone is found and connected. (If you get PMT has changed error, you need to change in SP Flash Tool from "Download Only" to "Firmware Upgrade" but you will need a backup that contains ALL files then including the cache and usrdata files, or it will not allow to flash. Also the phone will be formatted first with Firmware Upgrade, and then flashed.)
9. Now wait while it flashes all files, when it is done, a window will popup white a Green circle. Now you can disconnect the cable, close Splflashtool and reboot the phone. The phone should now boot up with the new ROM.
10. A good thing can be to do a full factory reset after your booted or do it in CWM, to clear all caches. But not necessary.
To enter Recovery or Download mode - turn phone completly off then
Download mode = vol up + pwr (hold both down for several seconds)
Recovery = vol down + pwr (hold both down for several seconds)
ROMs can be found on
http://needrom.com
http://pan.baidu.com/share/home?uk=2637246389#category/type=0
How to 1-CLICK-ROOT Mediatek 4.2 or 4.4 KitKat Smartphones and change iRoot to normal SuperSU
How to BACKUP / READBACK Mediatek MTK Smartphones with MTK Droid Tools / SP Flash Tool
Here a video how you use SP Flash Tool and flash a ROM (whole process, using Windows 7)
How to repair/change IMEI's with MAUI META on Mediatek Smartphones

s7yler said:
Hi
This is a guide to ROOT, backup and flash your MTK65xx device written by s7yler.
More guides & reviews on my Youtubechannel http://www.Youtube.com/s7yler
(Tools used are Framaroot, MTKDroidtools/CWM and SpflashTool)
I will try to write this guide in step by step, so everyone can understand it. This is for PC and will work with Windows 7.
-> All is done by your own risk! this is just a guide to help people with the tools and process. <-
How to ROOT the phone first
1. Get the latest Framaroot apk here http://forum.xda-developers.com/apps/framaroot/root-framaroot-one-click-apk-to-root-t2130276
2. Download it and install it on the phone, open the Framaroot app on the phone.
3. Let it be on Install SuperSU, and try the last method, if that dont work, then try one of the 2 others.
4. Then it should say success root, and now reboot the phone.
5. After reboot the phone should be ROOTED, download root checker from the Play store and verify that your rooted.
How to make a backup of your stock ROM / MTK phone
1. You have you brand new MTK phone.
2. What I do first is to install all possible drivers. So you go to your PC and install these apps/drivers:
Snappea - http://www.snappea.com/windows
Pdanet drivers - http://pdanet.co/a/ (When it ask what device you have in the install process, just say "Other")
Mediatek Preloader USB VCOM Drivers - http://www.magicdriver.com/driver4214-ver_1.1123.0.html
3. On your MTK phone you must in "Developer Options" enable "USB debugging mode".
4. Now download MTK Droid Tools here http://forum.xda-developers.com/showpost.php?p=49597819&postcount=922
5. Start MTK Droid Tools, and connect your phone with the USB cable to the PC. (if Windows install some drivers, then let it install them automatically).
6. Now on the first page of MTK Droid Tools, it should display all infos about the phone when you connect it.
7. If the sqare is Green, then you have root shell and ready, if its not green, press the ROOT button to the right in MTK Droid tools.
8. Click the "IMEI/NVRAM" button and then Backup to backup your IMEI/NVRAM, the backup files will be inside of the MTK Droid Tools folder.
Also you can manually write down your IMEI number just in case it should be lost.
9. Now go to the tap "root, backup, recovery" (in MTK Droid Tools).
10. Click the Backup button, and it will create a complete backup of your ROM.
11. When it is finished then also click "To prepare blocks for FlashTool", that will convert the backup to be compatible with Spflashtool.
12. After the backup is done it will be inside "backup" in the MTK Droid Tools folder. And inside it there will also be a new folder called "!Flash files Spflashtool" Inside there the files for Spflashtool is. So when loading your backup with Spflashtool you must load the scatter file from inside there.
13. Now to install CWM (clockworkmod recovery) In MTK Droidtools, choose "To use boot from phone" and click the "Recovery and Boot" button. It will ask you a lot, just say yes every time, and it will end of sending CWM recovery to the phone and reboot into it on the phone. After you see CWM on the phone you know it is done. You can switch the menu with the volume keys, and the power is the select button.
14. Inside CWM you can also do a complete backup of your phone (remember to have enough space, you can do the backup to the internal storage OR to the SDcard). I recommed doing that because CWM makes another backup than the one made with MTK Droid Tools. That is more complete. So if you should get problems or loose something, you can always run your CWM backup into your phone and it will be as before.
15. After your done the backup, copy the backup also to a safe place on your PC. Just in case!
16. So now your Rooted, have installed CWM recovery, have a IMEI/NVRAM backup and a backup for Spflash Tools plus CWM backup.
To flash a backup or ROM with Spflashtool:
1. Go download Spflash tool here http://forum.xda-developers.com/showthread.php?t=1982576
Both version 3 or 5 should be good to use. If your having problems with one of them, try another version.
2. Disconnect your phone if connected with USB to the PC, and turn OFF the phone completely, also take out the battery if possible (but can also work with the battery inside the phone, for phones with builtin battery).
2. Start Flash_tool.exe to start the program
3. Now hit the "Scatter-loading" button, and go to the backup or ROM, inside the folder "!Flash files Spflashtool" load the scatter.txt file. (ALWAYS only load a ROM that is 100% made for your phone, flashing a wrong ROM may make your phone non-bootable)
4. When the scatter file is loaded, it will show all the content in the Spflashtool window.
5. If you only need for example to flash the EBR files, you can deselect all the others. But remember that it must be same ROM or backup.
6. Hit the "Download" button in Spflashtool. Then there should be some lines with colors showing that it loads the files.
7. When it stopps to flash/load, connect your phone with the USB cable, remember the phone must be OFF.
8. Now it should connect (maybe Windows install some drivers by now - the MTK65xx Preloader drivers) and it will in the end continue to flash in Spflashtool when the phone is found and connected.
9. Now wait while it flashes all files, when it is done, a window will popup white a Green circle. Now you can disconnect the cable, close Splflashtool and reboot the phone. The phone should now boot up with the new ROM.
10. A good thing can be to do a full factory reset after your booted or do it in CWM, to clear all caches. But not necessary.
Click to expand...
Click to collapse
hey great guide man, but please have a mod change the title, it makes it sound like any phone could be rooted this way only to open it and be disapointed that its for MTK65xx only. i would do something like this
[How to][MTK65XX] ROOT, Backup & Flash (MTKDroidTools, Spflashtool, CWM)

Trozzul said:
hey great guide man, but please have a mod change the title, it makes it sound like any phone could be rooted this way only to open it and be disapointed that its for MTK65xx only. i would do something like this
[How to][MTK65XX] ROOT, Backup & Flash (MTKDroidTools, Spflashtool, CWM)
Click to expand...
Click to collapse
thank you to my friends so Root I do not know how to just flash the file with flash ebr tools, I do not know the use that is why I ask for help on using just to flash the two files ; thank you again.
I do not know how to use the software to just flash the two files.
and im a french user

Trozzul said:
hey great guide man, but please have a mod change the title, it makes it sound like any phone could be rooted this way only to open it and be disapointed that its for MTK65xx only. i would do something like this
[How to][MTK65XX] ROOT, Backup & Flash (MTKDroidTools, Spflashtool, CWM)
Click to expand...
Click to collapse
Hey sorry, I changed my text now. The ROOT part is not only for MTK phones, also other devices. Here is alephzains list of supported devices: http://forum.xda-developers.com/apps/framaroot/framaroot-supported-devices-t2722980
You also may try it on others, the worst there can happen is that it just says root failed, and not rooting the device. But then you at least have tried.

Rocfiles said:
thank you to my friends so Root I do not know how to just flash the file with flash ebr tools, I do not know the use that is why I ask for help on using just to flash the two files ; thank you again.
I do not know how to use the software to just flash the two files.
and im a french user
Click to expand...
Click to collapse
In Spflash tool load the scatter file from the backup or ROM directory where you also have all files including the modded EBR files, when loaded it will show all the content to flash, every line has a checkmark in front, uncheck everything but the EBR1 and EBR2. And then flash as I write in the guide. That way it will only flash the EBR1 and 2 to the phone.

Hope i can get this right
Hey whats up bro. Thanks for your efforts on helping with this forum. I have the hdc one max and it do not have a removable battery. Im trying to use sp flash tool to retore to stock with rom but i have no way of getting spft to recognize the device to start. Any solution?

MajorsCloset said:
Hey whats up bro. Thanks for your efforts on helping with this forum. I have the hdc one max and it do not have a removable battery. Im trying to use sp flash tool to retore to stock with rom but i have no way of getting spft to recognize the device to start. Any solution?
Click to expand...
Click to collapse
So you did install all the drivers I write about in my guide, and rebooted? Normally Spflash tool should recognize the phone after that. (and set the USB debugging mode to on?)

Thank you! Thank you! Thank you!
s7yler said:
So you did install all the drivers I write about in my guide, and rebooted? Normally Spflash tool should recognize the phone after that. (and set the USB debugging mode to on?)
Click to expand...
Click to collapse
thanks for everything bro. i manage to finally get the vcom driver installed. with a lil help from usbreview. i flashed the rom i downloaded from needrom like you suggested and bam im back in business. thanks alot. i managed to control the flickering/random button pressing by turning brightness up as a temporary fix. i will try a fix i just found, a little later.

MajorsCloset said:
thanks for everything bro. i manage to finally get the vcom driver installed. with a lil help from usbreview. i flashed the rom i downloaded from needrom like you suggested and bam im back in business. thanks alot. i managed to control the flickering/random button pressing by turning brightness up as a temporary fix. i will try a fix i just found, a little later.
Click to expand...
Click to collapse
I am glad that it worked for you. Does the Youtube app work? can you login on Youtube? with the needrom ROM? or how does the Gapps react on this ROM now?

s7yler said:
I am glad that it worked for you. Does the Youtube app work? can you login on Youtube? with the needrom ROM? or how does the Gapps react on this ROM now?
Click to expand...
Click to collapse
it may be just a update for bugs. the only difference i notice was a x to kill all apps but it still dont work. oh and more notification shortcuts. still cant login in into yourtube and i really need my google apps. i used your guide but i got the drivers from 4shared. i appreciate all your help for real. only if this device wasnt defected from jump with this flicker i would deal with it. i might sell it. smh. i really like this device.lol.

Hi!
For the last few days I was trying to find the right ROM for me. So I had to learn about MTK Tools and SP Flash tool and I even succeeded with loading different ROMs. What I did not succeed is to restore the original backup made with MTK tools. I followed the tutorial from the first post, the flashing operation ended OK but my smartphone (THL w200s) just wouldn't start. As a matter of fact it starts the beginning but after it passes the animated log it stops. I did not flash the CWM recovery on my device before creating the backup as I wanted to save a snapshot of the original ROM as it was from the factory. More than this, I installed a fresh ROM (I guess it was exactly the same with the default one), everything was OK, I rooted and made my settings (configure emails, etc.) and I made a backup with MTK tools. I had the same issue: I restored the backup with SP Flash Tools, flashing was OK but after that the phone would not start.
What am I doing wrong?

s7yler said:
Hi
This is a guide to ROOT, backup and flash your MTK65xx or Other device (Supported devices: http://forum.xda-developers.com/apps/framaroot/framaroot-supported-devices-t2722980 all credits to alephzain) written by s7yler.
More guides & reviews on my Youtubechannel http://www.Youtube.com/s7yler
(Tools used are Framaroot, MTKDroidtools/CWM and SpflashTool)
I will try to write this guide in step by step, so everyone can understand it. This is for PC and will work with Windows 7.
-> All is done by your own risk! this is just a guide to help people with the tools and process. <-
How to ROOT the phone first
1. Get the latest Framaroot apk here http://forum.xda-developers.com/apps/framaroot/root-framaroot-one-click-apk-to-root-t2130276
2. Download it and install it on the phone, open the Framaroot app on the phone.
3. Let it be on Install SuperSU, and try the last method, if that dont work, then try one of the 2 others.
4. Then it should say success root, and now reboot the phone.
5. After reboot the phone should be ROOTED, download root checker from the Play store and verify that your rooted.
How to make a simple backup of your stock ROM / MTK phone
1. You have you brand new MTK phone.
2. What I do first is to install all possible drivers. So you go to your PC and install these apps/drivers:
Snappea - http://www.snappea.com/windows
Pdanet drivers - http://pdanet.co/a/ (When it ask what device you have in the install process, just say "Other")
Mediatek Preloader USB VCOM Drivers - (Install file) http://www.mediafire.com/download/cypm22rgs2k83ji/MT6577+USB+VCOM+drivers.rar and here the raw drivers http://www.magicdriver.com/driver4214-ver_1.1123.0.html
3. On your MTK phone you must in "Developer Options" enable "USB debugging mode".
4. Now download MTK Droid Tools here http://forum.xda-developers.com/showpost.php?p=49597819&postcount=922
5. Start MTK Droid Tools, and connect your phone with the USB cable to the PC. (if Windows install some drivers, then let it install them automatically).
6. Now on the first page of MTK Droid Tools, it should display all infos about the phone when you connect it.
7. If the sqare is Green, then you have root shell and ready, if its not green, press the ROOT button to the right in MTK Droid tools.
8. Click the "IMEI/NVRAM" button and then Backup to backup your IMEI/NVRAM, the backup files will be inside of the MTK Droid Tools folder.
Also you can manually write down your IMEI number just in case it should be lost.
9. Now go to the tap "root, backup, recovery" (in MTK Droid Tools).
10. Click the Backup button, and it will create a complete backup of your ROM. (in the end it will ask, if you want to pack it, just answer no)
11. When it is finished then also click "To prepare blocks for FlashTool", that will convert the backup to be compatible with Spflashtool. (choose the files.md5 inside the backup folder)
12. After the backup is done it will be inside "backup" in the MTK Droid Tools folder. And inside it there will also be a new folder called "!Files_to_FlashTool" Inside there the files for Spflashtool is. So when loading your backup with Spflashtool you must load the scatter file from inside there.
13. Now to install CWM (clockworkmod recovery) In MTK Droidtools, choose "To use boot from phone" and click the "Recovery and Boot" button. It will ask you a lot, just say yes every time, and it will end of sending CWM recovery to the phone and reboot into it on the phone. After you see CWM on the phone you know it is done. You can switch the menu with the volume keys, and the power is the select button.
14. Inside CWM you can also do a complete backup of your phone (remember to have enough space, you can do the backup to the internal storage OR to the SDcard - try "backup" if that fails then choose instead "backup to external sd" or vice versa). I recommed doing that because CWM makes another backup than the one made with MTK Droid Tools. So if you should get problems or loose something, you can always run your CWM backup into your phone and it will be as before.
15. After your done the backup, copy the backup also to a safe place on your PC. Just in case!
16. So now your Rooted, have installed CWM recovery, have a IMEI/NVRAM backup and a backup for Spflash Tools plus CWM backup.
To make a more advanced & complete 1:1 ReadBack ROM backup using SP FlashTool please check this guide here:
http://forum.gsmhosting.com/vbb/f60...artphone-how-read-backup-1656510/#post9415324
or here:
http://pinoyscreencast.net/how-to/g...-smartphones-using-spft-mtk-droid-root-tools/
To flash a backup or ROM with Spflashtool:
Never needlessly Download preloader and DSP_BL blocks! It is always dangerous! On some models of phones you will have a brick even if you download these blocks read from phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM.
1. Go download Spflash tool here http://forum.xda-developers.com/showthread.php?t=1982576
Both version 3 or 5 should be good to use. If your having problems with one of them, try another version.
2. Disconnect your phone if connected with USB to the PC, and turn OFF the phone completely, also take out the battery if possible (but can also work with the battery inside the phone, for phones with builtin battery).
2. When you now again connect the USB cable to the phone with the PC while the phone is still off, Windows should popup and beginn to install the MTK65XX Preloader Drivers, this only happens if you installed the Mediatek Preloader USB VCOM Drivers correct in Windows. After they successfully installed, disconnect the USB cable again.
2. Start Flash_tool.exe to start the program
3. Now hit the "Scatter-loading" button, and go to the backup or ROM, inside the folder "!Flash files Spflashtool" load the scatter.txt file. (ALWAYS only load a ROM that is 100% made for your phone, flashing a wrong ROM may make your phone non-bootable)
4. When the scatter file is loaded, it will show all the content in the Spflashtool window.
5. If you only need for example to flash the EBR files, you can deselect all the others. But remember that it must be same ROM or backup.
6. Hit the "Download" button in Spflashtool. Then there should be some pink lines with colors showing that it loads the files.
7. When it stopps to flash/load, connect your phone with the USB cable, remember the phone must be OFF (and without the battery inside if possible to remove). If nothing happens then maybe it is necessary to press at the same time with connect of a cable the camera or volume buttons. For example, hold the volume up button down, insert the USB cable, and then insert the battery (still holding the volume up button down) when you hear it connect in Windows and the colored lines begins to move, let go off the volume up button.
8. Now it should connect (maybe Windows install some drivers by now - the MTK65xx Preloader drivers) and it will in the end continue to flash in Spflashtool when the phone is found and connected.
9. Now wait while it flashes all files, when it is done, a window will popup white a Green circle. Now you can disconnect the cable, close Splflashtool and reboot the phone. The phone should now boot up with the new ROM.
10. A good thing can be to do a full factory reset after your booted or do it in CWM, to clear all caches. But not necessary.
To enter Recovery or Download mode - turn phone completly off then
Download mode = vol up + pwr (hold both down for several seconds)
Recovery = vol down + pwr (hold both down for several seconds)
ROMs can be found on
http://needrom.com
http://pan.baidu.com/share/home?uk=2637246389#category/type=0
Click to expand...
Click to collapse
thax a lot bro,.,.i tried so many ways to port CW<M to my spice Mi-436,.,bt never succeded
bt after reading your toturial i did it man!!!!
A TONSSSSS of thanks !!!!!

Shaunak Falconzz Pandey said:
thax a lot bro,.,.i tried so many ways to port CW<M to my spice Mi-436,.,bt never succeded
bt after reading your toturial i did it man!!!!
A TONSSSSS of thanks !!!!!
Click to expand...
Click to collapse
I am happy to hear that it worked for you thanks for your comment.

I'm friends with Ruth framaroot phone and then off ... then mtk droid software with admin access and I'll be left bottom blue square root, and after OK, now I'm off to re-using software I could not come up with the phone and check it again before going off the bright green and blue non Ruth ... WHenever the phone or out ROM Mikham CWR Rykhn and are forced to ROM Disturb mobile phone you like'm going to be all Fast boot he has to change imei number do so because they must complete phone mtk software up to took root after changing the number (phone number, I jumped backups without ....) time for the tell greenfield No refused'd action I called the representative has not taken a pay ..... not so mythical after a few moments she wants a ...
I will be grateful if anyone knows how to fix the flaw lead ...
All are according to the latest software version XDA
my phone.....huawei g700-u10

MTK Droid error message
s7yler said:
Hi
This is a guide to ROOT, backup and flash your MTK65xx or Other device (Supported devices: http://forum.xda-developers.com/apps/framaroot/framaroot-supported-devices-t2722980 all credits to alephzain) written by s7yler.
More guides & reviews on my Youtubechannel http://www.Youtube.com/s7yler
(Tools used are Framaroot, MTKDroidtools/CWM and SpflashTool)
I will try to write this guide in step by step, so everyone can understand it. This is for PC and will work with Windows 7.
-> All is done by your own risk! this is just a guide to help people with the tools and process. <-
How to ROOT the phone first
1. Get the latest Framaroot apk here http://forum.xda-developers.com/apps/framaroot/root-framaroot-one-click-apk-to-root-t2130276
2. Download it and install it on the phone, open the Framaroot app on the phone.
3. Let it be on Install SuperSU, and try the last method, if that dont work, then try one of the 2 others.
4. Then it should say success root, and now reboot the phone.
5. After reboot the phone should be ROOTED, download root checker from the Play store and verify that your rooted.
How to make a simple backup (not completly 1:1) of your stock ROM / MTK phone
1. You have you brand new MTK phone.
2. What I do first is to install all possible drivers. So you go to your PC and install these apps/drivers:
Snappea - http://www.snappea.com/windows
Pdanet drivers - http://pdanet.co/a/ (When it ask what device you have in the install process, just say "Other")
Mediatek Preloader USB VCOM Drivers - (Install file) http://www.mediafire.com/download/cypm22rgs2k83ji/MT6577+USB+VCOM+drivers.rar and here the raw drivers http://www.magicdriver.com/driver4214-ver_1.1123.0.html
3. On your MTK phone you must in "Developer Options" enable "USB debugging mode".
4. Now download MTK Droid Tools here http://forum.xda-developers.com/showpost.php?p=49597819&postcount=922
5. Start MTK Droid Tools, and connect your phone with the USB cable to the PC. (if Windows install some drivers, then let it install them automatically).
6. Now on the first page of MTK Droid Tools, it should display all infos about the phone when you connect it.
7. If the sqare is Green, then you have root shell and ready, if its not green, press the ROOT button to the right in MTK Droid tools.
8. Click the "IMEI/NVRAM" button and then Backup to backup your IMEI/NVRAM, the backup files will be inside of the MTK Droid Tools folder.
Also you can manually write down your IMEI number just in case it should be lost.
9. Now go to the tap "root, backup, recovery" (in MTK Droid Tools).
10. Click the Backup button, and it will create a complete backup of your ROM. (in the end it will ask, if you want to pack it, just answer no)
11. When it is finished then also click "To prepare blocks for FlashTool", that will convert the backup to be compatible with Spflashtool. (choose the files.md5 inside the backup folder)
12. After the backup is done it will be inside "backup" in the MTK Droid Tools folder. And inside it there will also be a new folder called "!Files_to_FlashTool" Inside there the files for Spflashtool is. So when loading your backup with Spflashtool you must load the scatter file from inside there.
13. Now to install CWM (clockworkmod recovery) In MTK Droidtools, choose "To use boot from phone" and click the "Recovery and Boot" button. It will ask you a lot, just say yes every time, and it will end of sending CWM recovery to the phone and reboot into it on the phone. After you see CWM on the phone you know it is done. You can switch the menu with the volume keys, and the power is the select button.
14. Inside CWM you can also do a complete backup of your phone (remember to have enough space, you can do the backup to the internal storage OR to the SDcard - try "backup" if that fails then choose instead "backup to external sd" or vice versa). I recommed doing that because CWM makes another backup than the one made with MTK Droid Tools. So if you should get problems or loose something, you can always run your CWM backup into your phone and it will be as before.
15. After your done the backup, copy the backup also to a safe place on your PC. Just in case!
16. So now your Rooted, have installed CWM recovery, have a IMEI/NVRAM backup and a backup for Spflash Tools plus CWM backup.
To make a 100% FULL 1:1 (more advanced) ReadBack ROM backup using SP FlashTool please check these guides here, and learn how to:
http://forum.gsmhosting.com/vbb/f60...artphone-how-read-backup-1656510/#post9415324
or here:
http://pinoyscreencast.net/how-to/g...-smartphones-using-spft-mtk-droid-root-tools/
To flash a backup or ROM with Spflashtool:
Disclaimer: Don't flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones you will have a brick even if you download these blocks read from phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM. I take no responsibility for any harm done while attempting this!
1. Go download Spflash tool here http://forum.xda-developers.com/showthread.php?t=1982576
Both version 3 or 5 should be good to use. If your having problems with one of them or they crash, try this newer version here: http://forum.xda-developers.com/showthread.php?t=2650125
2. Disconnect your phone if connected with USB to the PC, and turn OFF the phone completely, also take out the battery if possible (but can also work with the battery inside the phone, for phones with builtin battery).
2. When you now again connect the USB cable to the phone with the PC while the phone is still off, Windows should popup and beginn to install the MTK65XX Preloader Drivers, this only happens if you installed the Mediatek Preloader USB VCOM Drivers correct in Windows. After they successfully installed, disconnect the USB cable again.
2. Start Flash_tool.exe to start the program
3. Now hit the "Scatter-loading" button, and go to the backup or ROM, inside the folder "!Flash files Spflashtool" load the scatter.txt file. (ALWAYS only load a ROM that is 100% made for your phone, flashing a wrong ROM may make your phone non-bootable)
4. When the scatter file is loaded, it will show all the content in the Spflashtool window.
5. If you only need for example to flash the EBR files, you can deselect all the others. But remember that it must be same ROM or backup.
6. Hit the "Download" button in Spflashtool. Then there should be some pink lines with colors showing that it loads the files.
7. When it stopps to flash/load, connect your phone with the USB cable, remember the phone must be OFF (and without the battery inside if possible to remove). If nothing happens then maybe it is necessary to press at the same time with connect of a cable the camera or volume buttons. For example, hold the volume up button down, insert the USB cable, and then insert the battery (still holding the volume up button down) when you hear it connect in Windows and the colored lines begins to move, let go off the volume up button.
8. Now it should connect (maybe Windows install some drivers by now - the MTK65xx Preloader drivers) and it will in the end continue to flash in Spflashtool when the phone is found and connected.
9. Now wait while it flashes all files, when it is done, a window will popup white a Green circle. Now you can disconnect the cable, close Splflashtool and reboot the phone. The phone should now boot up with the new ROM.
10. A good thing can be to do a full factory reset after your booted or do it in CWM, to clear all caches. But not necessary.
To enter Recovery or Download mode - turn phone completly off then
Download mode = vol up + pwr (hold both down for several seconds)
Recovery = vol down + pwr (hold both down for several seconds)
ROMs can be found on
http://needrom.com
http://pan.baidu.com/share/home?uk=2637246389#category/type=0
Click to expand...
Click to collapse
------------------------------------------------------------------------------------------------------------
I'm receiving an error message "SU inaccessible" after hitting the ROOT icon. The phone is a No.1 S7 MTK6589.
I previously tried using the Frameroot app but it failed as well.
Any ideas what the problem might be and how to solve?
Thanks,
Ruby

UPDATE
I have updated the Original Post with a video now, that show the whole process how to flash and use SP Flash Tool.
As always, everything is done at your own risk. It is just a guide. This video is for education only.

Very Useful Tips
Hy Man Thanks 4 This Useful Tips. Very Impressed.I Like Xda VeryMuch.

Fun accident
Well here's my story.
I was trying to debrand some Huawei Y330-U05 in order to resell them. My first clue was to root the devices and remove all the Entel PCS crap, but I was unable to remove the Boot Splashscreen. So I looked over the net and I could not find a compatible ROM for my model. I downloaded a Y330-U01 ROM from Europe and I tried to flash it figuring that later I'd have to fix the 3G bands. FlashTools did not let me do that and I had the stupid idea to boot the biit.img and recovery.img from the U01 into the U05 with MTKdroidTools. Bricked the phone, and the only way to bring it back was to use the U01 ROM and flash it back. I changed my device from U05 to U01, like I wanted at first but I cant change the 3G bands and I don't have 3G connnection now.
I can't flash back the U05 backup ROMs I did from the phone before I started messing with them because the of the model mismatch (Phone now thinks it is a U01 version). And since there is no stock ROM for the U05 model to download, except for an UPDATE.APP from Movistar Mexico that phone refuses to accept, I'm afraid that if I reverse the whloe process I will end up with a bricked phone and no Stock ROM to bring it back.
Here comes the question. How do I force install a WRONG ROM into my phone? Remember: my Y330-U05 now thinks it is a Y330-U01.
Thanks a lot!

Blu Studio 5.0 C HD
Can the blu studio 5.0c hd be rooted this way? A bit scared to do it because this is my daily driver

SU Inaccessible error
Ruby_97 said:
------------------------------------------------------------------------------------------------------------
I'm receiving an error message "SU inaccessible" after hitting the ROOT icon. The phone is a No.1 S7 MTK6589.
I previously tried using the Frameroot app but it failed as well.
Any ideas what the problem might be and how to solve?
Thanks,
Ruby
Click to expand...
Click to collapse
i saw your screenshot and yellow box at the bottom clearly indicates that your device has not been rooted properly. adb still exists as secure region. it is said that your device should said to be rooted properly only when your device got adb insecure. However, if your device has locked bootloader, doing so, i.e. entering or making adb insecure may lead your device to dead boot, a stage from which there are only two ways to survive from:- JTAG/RIFF box OR by replacing motherboard!!!!
However, if your bootloader is unlocked and only if your device is dev friendly, following link may help you to get green box at the bottom of MTK Droid Root Tools indicating your device has proper root access.
However, i have successfully solved this error in my panasonic p81 by making adb insecure.
Though, Do this on your own risk....Remember again, making adb insecure may make your device FAIL!!!!
Head over to following link:-
http://forum.xda-developers.com/showthread.php?t=1687590
Thanks to dev Chainfire again for this wonderful application....

CWM recovery, Backup (Read back+CWM) and Root Micromax Canvas HD+

CWM AND BACKUP
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.
Problem in installation?? Go here
Or use the drivers i use:here (install legacy drivers, google)
2. Download scatter from attachments .
3. Open SP flash tools, load scatter in sp flash tools and go to read back tab.
4. Click 'Add' and tap on added read back entry.
5. Select any path to save file and click ok, write 0x03d80000 in length and click ok.
6. Click on read back and connect phone without battery. Wait till it completes.
7. Once you see a green circle, close sp flash tools and switch on the phone.
8. When the phone is on, connect it to pc. See if any notification of 'usb debugging' comes in phone, if not, go to settings->about phone->and tap build number 7 times to enable debugging options.
9. Go back and enter developers options(in settings), and check usb debugging on.
10. Now run mtk driod tools and it will detect phone.
11. In mtk droid tools, click 'root, backup and recovery' tab.
12. Click 'To process file ROM_ from Flash Tool.
13. Locate the file you got from read back.
14. Say yes to make CWM recovery automatically.
15. Now wait again.
Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
FLASHING CWM AND ROOT:
1. Start SP flash tools and click on 'recovery' in sp flash tools and select the CWM recovery made by mtk droid tools (Micromax-A190_xxxx_recovery_) .
2. Click Download in sp flash tools, remove the battery from phone and connect it to pc.
A green circle/download ok will confirm flashing.
3. Insert battery and reboot to recovery. Make a Backup.
4. Select install from sd card and select Unite_2_4.4.2_Proper root......zip and say yes to flash.
5. Reboot, Done.

Finally it happens.. I rooted my phone successfully, n it's confirmed working ☺☺hands down Bro.. U r the man.. Big big cheers for the dev to make it happen.. Thanks a million times bro.. Another fabulous work for us.. God bless u ???

please reply that doing read back is important whats that

Vishesh said:
Finally it happens.. I rooted my phone successfully, n it's confirmed working ☺☺hands down Bro.. U r the man.. Big big cheers for the dev to make it happen.. Thanks a million times bro.. Another fabulous work for us.. God bless u ???
Click to expand...
Click to collapse
brother please help to install drivers iam not able to install drivers when iconnect my phone to pc wid no battery preloader usb vcom driver installation comes but then it says device unplugged Another thing, when I connect my A190 phone without battery, the device manager list updates itself every two seconds: once it shows the preloader vcom port and then in the next refresh there's no vcom port and this process repeats. Any idea why?

Can you please give Canvas HD Plus Stock Wallpapers.. Please...

somu12345 said:
brother please help to install drivers iam not able to install drivers when iconnect my phone to pc wid no battery preloader usb vcom driver installation comes but then it says device unplugged Another thing, when I connect my A190 phone without battery, the device manager list updates itself every two seconds: once it shows the preloader vcom port and then in the next refresh there's no vcom port and this process repeats. Any idea why?
Click to expand...
Click to collapse
that 2 seconds is what important ..
u hav to click tat vcom port and choose update driver with the one u downloaded

Soft bricked Panasonic P81

Hi Friends,
This is my first post at XDA.
I unfortunately bricked my Panasonic P81 after rooting it and adding XHalo app and the boot manager app from the Xposed Framework.
The situation is as follows-
I can get to the logo, it screams Panasonic and then doesnt boot. I dont have CWA installed and worse, my SD card which had my stock backup is also lost. This means I need a mechanism to stock recover and perhaps flash boot.img and recovery.img?
I am stuck at this point, not sure how to proceed. I can get to recovery, have cleaned cache, backed up user data ,done a factory reset. Even after factory reset it still cant boot.
Please help me with a step-by-step instruction to recover, this phone is dear to me. How do I flash?(boot.img or rom) I have downloaded Sagar Patel's (good bless him!) backup and the images, but need guidance on how to flash and recover.
Please help friends and apologies for any incovenience. I am still a newbie

Guys please help!!

Driver-USB-PC connection problem
kartik.krish said:
Guys please help!!
Click to expand...
Click to collapse
Hope drivers are installed properly in your pc.
If you are going to use sp flash tool, Make sure SP flash tool is set to auto-detect com port, not manual selection
If you find that it is driver problem, following may help you.
Please note that there is nothing that much hard in driver installation as it is just to connect your device with your pc but because many users still face problem of driver installation, you can try following tricks!!!
It is observed by me that driver installation and adb interface problem do not happen in windows XP as eventually and generally it is happened in windows 7 and later…so, you can simply try on windows xp if you are able to do so…(you can use dual operating system too!!! Or good relation with neighbor/friends/colleagues/someone/all can be beneficial here!!!)
Note that all tricks here are not necessary to work, but it may still work for you….
Take one by one step, if the first step does not work for you, only then try next step. This is not all steps to be taken at once type guide…This is simply Try and error type tutorial/tricks…
There are following problems I have come to know regarding to driver installation and conflicts:-
Device is charging through usb cable but there is no usb option displaying on either device or no driver installation box/message/pop up appears in pc….
Missing sound of that usb-pc connection
Sound of disconnection after couple of seconds of connection
Adb interface is missing
Ok, sometimes changing usb connection type for example, from mass storage or mtp to camera, ptp, usb tethering or something else can bring adb interface…..
Try with different USB Cable. You can use original nokia or samsung tiny cable instead of cable having long length. Sometimes, length matters!!!!
Try in different USB Port.
Sometimes, you have to disable signature verification in your pc for proper installation of driver.
Had you disabled your antivirus before downloading, installing and while running your tools/softwares? You may need to do so…
Have you installed the software (or say, all associated softwares/tools) in C-System drive?, if not, then you should first install required software/tools in system drive that is usually C drive in Microsoft-Windows OS…or try after installing them on desktop.
Keep all necessary files/tools (driver files, flash tools, rom etc…) on desktop.
Download proper driver According to your model/device, According to chipset inside, According to Official site of manufacturer, Official site of chipset, through PC Suite/flash program of your device…
If the problem still not solve, you should try all available driver packages of your device one by one whether from official site of chipset inside your device, or any forum, adb, pdanet+ or foxfi, universal driver, VCOM Port driver, drivers from hexamob through play store, and find all possible packages and see if someone make positive result after installation…
If the problem still not solve, you should install remaining update packages of your system (PC) including all primary, secondary, essential, Non-essential updates….whatever, just install them all….reboot your pc…and see if problem is solved….
If you can connect the device but somehow found that device driver still not installed properly, just go to device manager in your pc, click on portable device, right click on your device and apply “Update driver”. Click on “automatically search” when a window prompt ask you.
If the problem still persists then,
Just remove all the drivers using usbdeview (I have given link also to download usbdeview in earlier post)
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
Install usbdeview and remove all the drivers
You can also fix this by showing the nonpresent devices in devicemanagement (google for show nonpresent devices for explanation)
Go to com ports, and delete all mediatek drivers except preloader driver. Now start over. It can help if you choose the same usb port where you had success last time.
Use Usbdeview to uninstall all the drivers before connection, restart the pc, Extract and keep driver zip files and other useful files/tools on desktop…just start your tool… and try to perform your tasks like backup…or restoring the backup…without worrying about that sound of disconnection you may listened after couple of seconds of connection or don’t even worry if you are just missing that sound of usb-pc connection….just try on your tool…
If still problem of driver installation persists, then simply use usbdeview and uninstall all drivers, restart your pc and try following steps:-
There are various ways to install proper drivers at the time of connecting the device with pc depending upon how you connect it.
Follow the procedure both with and without battery
Simply plug in via USB Cable
Connect by holding volume down button
Connect by holding volume up button
Connect by holding Power button
Connect by holding power and volume down
Connect by holding power and volume up
Connect by holding both volume up and down button
Connect by holding thrice volume up, down and power button
Connect by holding power and home button
Connect by holding power and menu button
Remember which method works and which drivers are installed
in LAN-Devices you may have different android device
Select/set drivers by hand and use the mtk usb driver, now Flashtool finds the phone
Suppose holding volume down method without battery works for you then what next you have to do is as below:-
1.TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2.HOLDING VOLUME DOWN CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME DOWN)
3.OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4.WAIT FOR 2-3 MINUTES
5.YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6.IN OTHER DEVICES ->MT65XX PRE-LOADER
7.RIGHT CLICK MT65XX PRELOADER
8.UPDATE DRIVER
9.LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10.IT WILL DO ITS STUFF
Install Mediatek drivers, preloaders, VCOM port etc…
Manually Install MediaTek USB VCOM Drivers
Requirement:-
1. Download MediaTek USB VCOM Drivers
2. Download USBDeview
Here is the link from you can get it:-
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
Procedure
(* Note: You might need to disable drivers signature verification in Windows for this to work smoothly.
If you want to turn off device driver signing in Windows completely, do the following.
Windows 7:-
1. Hit the Win+R keys together to open the run dialog
2. Type gpedit.msc to open the local groups policy
editor
3. Expand ‘Administrative Templates’ (it’s under ‘User Configuration’)
4. Expand ‘System’. Click ‘driver Installation’
5. In the right panel, double click on ‘Code Signing for Device Drivers’
6. Choose ‘Enabled’ in the window that appears.
7. In the underlying options, choose ‘Ignore’
8. This disables drivers signing in Windows 7, and now you can install unsigned drivers in Windows 7.
9. Click Apply, OK. Restart your computer to install unsigned drivers
Windows 8
1. Hold down the Windows key on your keyboard and press the letter C to open the Charm menu, then click the gear icon (Settings)
2. Click More PC Settings
3. Click General
4. Under Advanced Startup, click Restart Now
Note: In Windows 8.1, the ‘Restart Now’ button has moved to ‘PC Setting -> Update & Recovery -> Recovery.’
5. After restarting, click Troubleshoot
6. Click advanced options
7. Click Windows Startup Settings
8. Click Restart
9. After restarting your computer a second time,
choose Disable driver signature enforcement
from the list by typing the number 7 on your Keyboard Your computer will restart automatically.
10. After restarting, you will be able to install
unsigned drivers normally; however, Windows
will display a warning message. When the
warning appears, click Install this driver
software anyway. )
1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, and then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be)
Try in different PC
Sometimes windows XP works when windows 7 fails!!!
Case:-
It did the same thing with my MT6577 (Wiko Cink PEAX), so I connected it with a battery and without holding VOL+. Then "MT65xx preloader" appeared in device manager then disappeared (once). It is normal that it disappears. When you start Flash_tool and when you click Download (or whatever you want to do) THEN you connect the phone (in off state), and the flash operation will succeed.
Guess what? Once my Panasonic P81 could install driver and got detected after approx. 5 hours of continuous connection with win 7 x64!!! Meanwhile, I tried first usbdeview and then manually installation of mediatek driver but manual installation had failed as my p81 was only charging when it was connected with pc….So, mediatek – windows 7 conflicts….but, when I tried tiny (very small) nokia usb cable, it works instantly…
If you ever meet problem when you connect your android with your pc via usb cable and find that your android is charging but could not recognize or there isn’t that options of “USB connection” then just disconnect your android, power off it, remove battery, connect it without battery with your pc through usb, let it have some time to recognize your android or hear that voice of “usb connection” you were just missing…after that, insert battery and switch on your android…you are done!!!
Sometimes removing both sim cards and battery and then re-inserting them after a couple of seconds also works.
Try with different USB Cable
Try in different USB Port
Try in different PC
Sometimes windows XP works when windows 7 fails!!!
Use usbdeview to remove all the usb devices and then add your device
Find proper driver of your device:-
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing

panasonic p81 soft bricked
SP flash tool detected my P81 mobile
but i need rom ROM files to flash
please any one give me rom file to flash Panasonic P81 with SP flash tool

problem solved?
I also had similar problem & solved it. Tell me if the problem is no solved.

damn i don't know what the hell is going on inside my computer but i am not able to get those drivers or i don't know what's the problem. please help me where to get drivers for my panasonic p81 mobile. it is softbricked and i want to install stock rom and i have that cpb files but that ygdp tool isn't working i am in total chaos.
help me please

kartik.krish said:
Yo! I had bricked it too and that too by Xhalomulti window cuz app window is sh!t..... be cool .there is stock rom available at www.xdafirmware.com....google it....also You will recieve a .zip... extract to get .cpb file and use YGDP (assembly:: if ask for password at ygdp type 369)......tap config select cpb. Wait ...connect usb and click start........ok tutorial on Internet.... IMPORTANT THING:: YOU'LL NEED MTK VCOM DRIVER PR ELSE IT WON'T WORK.
Sent from my Panasonic P81 using XDA Labs
Click to expand...
Click to collapse

Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?

kartik.krish said:
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
Click to expand...
Click to collapse
Brother I am tired of finding any rom other than stock.on internet there is miui 6 but most people complained it damaged their devices....no cyanogen OS,Color os ,Aokp,Ressurection remix,paranoid nothing........ok i found a phone named Doogee Dagger DG550 having same spects but better ui than playmore and that recently got kitkat too. Im thinking of trying it..if it fails i've
Panasonic original (ok modded a bit) firmware i can flash from ygdp tool..... actually Panasonic P81 is nothing but clone of coolpad 7320 with cool show replaced by playmore and the gesture is new....same multiwindow and the music cafe is nothing but coolpad music renamed....literally im using 7320 rom with build. prop changed so on apps it shows im using p81........Ok if you find rom please post link..... Ps ive tried roms on www.needrom.com but is hopeless.
Sent from my Panasonic P81 using XDA Labs
---------- Post added at 04:39 AM ---------- Previous post was at 04:34 AM ----------
kartik.krish said:
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
Click to expand...
Click to collapse
In my opinion MIUI is best because it has a self large community like xda and launch updates per month so many that you will fed up installing them.....if you download and install one update you will be amazed that it will say 3 more system updates pending......and if you complain a bug next month it got fixed.....only thing is to find one...
PS don't download the miui 6 for p81..complained by many p81 user that it hard bricked the device.
And that miui is not official i.e. some developer made his own one and DO not tested that it works or not......
Sent from my Panasonic P81 using XDA Labs

Sir,My Panasonic eluga s is soft bricked, Not starting by pressing any key..it only Starts when connected to PC or charging.. That too in Fastboot mode.. While installing stock ROM using YGDP tool,I am not able to get my mobile in download mode..pls guide..

my panasonic p81 is hard brick,it is not detecting in pc by vcom and other drivers even not booting or charging,please help me devs.

I am connecting my p81 with my sound system but now i cannot hear the voice over a call properly plzz help me out

[ SOLVED ] Lenovo A850 won't power up after flashing ROM

Hi everyone.
I got a Lenovo A850 ( MTK 6582 ) here which is belong to my friend, it was full with malware apps or I can say a Trojan, Hijackers etc etc.. Because it like to turn off USB DEBUGGING option ( checkbox ) and downloading inappropriate apps into device and I decide to flash a new ROM I downloaded from needrom website and flashed using SP Tools. All processes went alright and SP tools 'Green Circle' popup. :good:
Then, I unplug USB and put battery and cover, and pressing Power button. Sadly, it won't turn ON anymore, just Red LED light.:crying::crying: I can't even enter recovery / bootloader. I was looking for solutions everywhere including in X-DA forum. Some said, It was Hardware problem, but how come? It was fine before I flashed a ROM. and now it's totally dead
I played around by pulling out a battery and pressing Volume buttons + power with USB cable attached to it and it finally respond to PC device manager by showing a MTK USB port I tried using SP tools again to flash another ROM with hopes it will fix but yeah, I know it won't work as MTK USB Port is not the right driver for SP tools. :silly:
What do i do now? Please someone help me.
Many thanks!
EDIT : PROBLEM SOLVED
Hello members,
Finally, I got this device alive again and if you are also having this issue and still can't fix it, you can now by following below steps;
Its time to revive your dead phone.
First, download below files:
- Download this A850 stock ROM here ( MTK6582 )
- Use this SP flash tool, here
- VCOM Mediatek Drivers pack ( required )
*Items required : USB cable, PC/Laptop, & Your dead phone.
OK now lets start...
2. Unzip ROM file and start SP flash tools, Load scatter file > Go to option > check DA DL all with checksum.
3. Uncheck all list and Select 'PRELOADER' only and press Download.
4. Remove battery from your phone, after 5 secs while pressing Vol + / Vol - or both, connect USB to you device. If you get no response from PC ( not recognize ), you have to unscrew and open your phone cover to manually jumper the 'Preloader Test point'. Please follow this guide here. However it's quiet advance step and please do it carefully at your own risk.:good:
5. Otherwise, after plug in USB, your PC will start installing Driver ( If it failed to install driver automatically, then you have to install it manually from VCOM Mediatek driver pack download earlier ).
6. If everything is right, SP flash tools will automatically detect your device via MTK USB port ( RED BAR PROGRESS ) and It will change it to Mediatek DA VCOM and PURPLE BAR PROGRESS show up and viola! GREEN CIRCLE popup!
DONE!
7. Now remove USB from your phone, Don't do anything yet, back to SP flash tools, and now Select all flash list except PRELOADER and press Download. and insert USB cable again and flash tools will start the process, wait until it finish flashing all img's ( Boot, Uboot, System, Data, MBR etc ).
If flashing processes done successfully, it will popup GREEN CIRCLE again, now you can take a deep breath :victory:
- Unplug USB > Put Battery ON > Press power button > You tell me what you feel :silly:
*Side Note : If you're having any issue like a boot loop, just boot into Recovery Mode and format data/cache and REBOOT.
CWM Recovery img here
*Automade using MTKDroidtools
Good Luck! :highfive::highfive:

RidzVarn said:
Hi everyone.
I got a Lenovo A850 ( MTK 6582 ) here which is belong to my friend, it was full with malware apps or I can say a Trojan, Hijackers etc etc.. Because it like to turn off USB DEBUGGING option ( checkbox ) and downloading inappropriate apps into device and I decide to flash a new ROM I downloaded from needrom website and flashed using SP Tools. All processes went alright and SP tools 'Green Circle' popup. :good:
Then, I unplug USB and put battery and cover, and pressing Power button. Sadly, it won't turn ON anymore, just Red LED light.:crying::crying: I can't even enter recovery / bootloader. I was looking for solutions everywhere including in X-DA forum. Some said, It was Hardware problem, but how come? It was fine before I flashed a ROM. and now it's totally dead
I played around by pulling out a battery and pressing Volume buttons + power with USB cable attached to it and it finally respond to PC device manager by showing a MTK USB port I tried using SP tools again to flash another ROM with hopes it will fix but yeah, I know it won't work as MTK USB Port is not the right driver for SP tools. :silly:
What do i do now? Please someone help me.
Many thanks!
EDIT : PROBLEM SOLVED
Hello members,
Finally, I got this device alive again and if you are also having this issue and still can't fix it, you can now by following below steps;
Its time to revive your dead phone.
First, download below files:
- Download this A850 stock ROM here ( MTK6582 )
- Use this SP flash tool, here
- VCOM Mediatek Drivers pack ( required )
*Items required : USB cable, PC/Laptop, & Your dead phone.
OK now lets start...
2. Unzip ROM file and start SP flash tools, Load scatter file > Go to option > check DA DL all with checksum.
3. Uncheck all list and Select 'PRELOADER' only and press Download.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. Remove battery from your phone, after 5 secs while pressing Vol + / Vol - or both, connect USB to you device. If you get no response from PC ( not recognize ), you have to unscrew and open your phone cover to manually jumper the 'Preloader Test point'. Please follow this guide here. However it's quiet advance step and please do it carefully at your own risk.:good:
5. Otherwise, after plug in USB, your PC will start installing Driver ( If it failed to install driver automatically, then you have to install it manually from VCOM Mediatek driver pack download earlier ).
6. If everything is right, SP flash tools will automatically detect your device via MTK USB port ( RED BAR PROGRESS ) and It will change it to Mediatek DA VCOM and PURPLE BAR PROGRESS show up and viola! GREEN CIRCLE popup!
DONE!
7. Now remove USB from your phone, Don't do anything yet, back to SP flash tools, and now Select all flash list except PRELOADER and press Download. and insert USB cable again and flash tools will start the process, wait until it finish flashing all img's ( Boot, Uboot, System, Data, MBR etc ).
If flashing processes done successfully, it will popup GREEN CIRCLE again, now you can take a deep breath :victory:
- Unplug USB > Put Battery ON > Press power button > You tell me what you feel :silly:
*Side Note : If you're having any issue like a boot loop, just boot into Recovery Mode and format data/cache and REBOOT.
CWM Recovery img here
*Automade using MTKDroidtools
Good Luck! :highfive::highfive:
Click to expand...
Click to collapse
Hi there, first to all, thanks for this information, im in the process of recover of my A850i after intall A850_S121 rom, the phone was bricked :S , im right know following your steps and in the FlashTool , when i select only the preloader and click download , FlashTool show a box that says "PMT changed for the ROM, it must be downloaded" , then i click help and ask me to do a " Format All + Download" , what should i do? Please Help! And i have another question in the dropdown menu wich option should be set ? download only ? , firmware upgrade? , format all + download? Thanks!!

bamatos said:
Hi there, first to all, thanks for this information, im in the process of recover of my A850i after intall A850_S121 rom, the phone was bricked :S , im right know following your steps and in the FlashTool , when i select only the preloader and click download , FlashTool show a box that says "PMT changed for the ROM, it must be downloaded" , then i click help and ask me to do a " Format All + Download" , what should i do? Please Help! And i have another question in the dropdown menu wich option should be set ? download only ? , firmware upgrade? , format all + download? Thanks!!
Click to expand...
Click to collapse
Hi there,
Try again using different version of SP tools. Hope it will fix. I got that error msg too before when using new SP flash tools.
Good luck![emoji1]
Sent from my 4027N using Tapatalk

Great share! Thanks for helping my exact problem as you are.
Thanks alot :highfive:

RidzVarn said:
Hi everyone.
I got a Lenovo A850 ( MTK 6582 ) here which is belong to my friend, it was full with malware apps or I can say a Trojan, Hijackers etc etc.. Because it like to turn off USB DEBUGGING option ( checkbox ) and downloading inappropriate apps into device and I decide to flash a new ROM I downloaded from needrom website and flashed using SP Tools. All processes went alright and SP tools 'Green Circle' popup. :good:
Then, I unplug USB and put battery and cover, and pressing Power button. Sadly, it won't turn ON anymore, just Red LED light.:crying::crying: I can't even enter recovery / bootloader. I was looking for solutions everywhere including in X-DA forum. Some said, It was Hardware problem, but how come? It was fine before I flashed a ROM. and now it's totally dead
I played around by pulling out a battery and pressing Volume buttons + power with USB cable attached to it and it finally respond to PC device manager by showing a MTK USB port I tried using SP tools again to flash another ROM with hopes it will fix but yeah, I know it won't work as MTK USB Port is not the right driver for SP tools. :silly:
What do i do now? Please someone help me.
Many thanks!
EDIT : PROBLEM SOLVED
Hello members,
Finally, I got this device alive again and if you are also having this issue and still can't fix it, you can now by following below steps;
Its time to revive your dead phone.
First, download below files:
- Download this A850 stock ROM here ( MTK6582 )
- Use this SP flash tool, here
- VCOM Mediatek Drivers pack ( required )
*Items required : USB cable, PC/Laptop, & Your dead phone.
OK now lets start...
2. Unzip ROM file and start SP flash tools, Load scatter file > Go to option > check DA DL all with checksum.
3. Uncheck all list and Select 'PRELOADER' only and press Download.
4. Remove battery from your phone, after 5 secs while pressing Vol + / Vol - or both, connect USB to you device. If you get no response from PC ( not recognize ), you have to unscrew and open your phone cover to manually jumper the 'Preloader Test point'. Please follow this guide here. However it's quiet advance step and please do it carefully at your own risk.:good:
5. Otherwise, after plug in USB, your PC will start installing Driver ( If it failed to install driver automatically, then you have to install it manually from VCOM Mediatek driver pack download earlier ).
6. If everything is right, SP flash tools will automatically detect your device via MTK USB port ( RED BAR PROGRESS ) and It will change it to Mediatek DA VCOM and PURPLE BAR PROGRESS show up and viola! GREEN CIRCLE popup!
DONE!
7. Now remove USB from your phone, Don't do anything yet, back to SP flash tools, and now Select all flash list except PRELOADER and press Download. and insert USB cable again and flash tools will start the process, wait until it finish flashing all img's ( Boot, Uboot, System, Data, MBR etc ).
If flashing processes done successfully, it will popup GREEN CIRCLE again, now you can take a deep breath :victory:
- Unplug USB > Put Battery ON > Press power button > You tell me what you feel :silly:
*Side Note : If you're having any issue like a boot loop, just boot into Recovery Mode and format data/cache and REBOOT.
CWM Recovery img here
*Automade using MTKDroidtools
Good Luck! :highfive::highfive:
Click to expand...
Click to collapse
Bro, boleh share backup x? Aku punya phone bricked, dah try rom official yang ada tapi x boleh.. nak try guna backup rom plak

Bro, boleh share backup x? Aku punya phone bricked, dah try rom official yang ada tapi x boleh.. nak try guna backup rom plak
Click to expand...
Click to collapse
Hi,
Sorry lama tak jenguk, backup pun dah tak ada dah. Dah tukar phone.

Bro..aq haritu format gune sp flashtool..kirenye macam nak format dulu baru download rom baru la..tapi lepas format tros mati fon nie..xleh turn on..yang ade cume lampu merah tu je..nak connect pc pon xleh..camane nak selesai mende ni bro??

Dead Lenovo s850 ....while trying some cn version rom
help me to get back my phone plz...as i was trying to install linerage os cn 13 i bricked my phone......n its not even power up.
kindly plz helpme to unbrick .
i download the stock rom n try to flash it through flash tool. but my windows cant recognize my device.....
so i install the driver .....vcom n cdc manually but still cant recognize it .

:good:

RidzVarn said:
Hi everyone.
I got a Lenovo A850 ( MTK 6582 ) here which is belong to my friend, it was full with malware apps or I can say a Trojan, Hijackers etc etc.. Because it like to turn off USB DEBUGGING option ( checkbox ) and downloading inappropriate apps into device and I decide to flash a new ROM I downloaded from needrom website and flashed using SP Tools. All processes went alright and SP tools 'Green Circle' popup. :good:
Then, I unplug USB and put battery and cover, and pressing Power button. Sadly, it won't turn ON anymore, just Red LED light.:crying::crying: I can't even enter recovery / bootloader. I was looking for solutions everywhere including in X-DA forum. Some said, It was Hardware problem, but how come? It was fine before I flashed a ROM. and now it's totally dead
I played around by pulling out a battery and pressing Volume buttons + power with USB cable attached to it and it finally respond to PC device manager by showing a MTK USB port I tried using SP tools again to flash another ROM with hopes it will fix but yeah, I know it won't work as MTK USB Port is not the right driver for SP tools. :silly:
What do i do now? Please someone help me.
Many thanks!
EDIT : PROBLEM SOLVED
Hello members,
Finally, I got this device alive again and if you are also having this issue and still can't fix it, you can now by following below steps;
Its time to revive your dead phone.
First, download below files:
- Download this A850 stock ROM here ( MTK6582 )
- Use this SP flash tool, here
- VCOM Mediatek Drivers pack ( required )
*Items required : USB cable, PC/Laptop, & Your dead phone.
OK now lets start...
2. Unzip ROM file and start SP flash tools, Load scatter file > Go to option > check DA DL all with checksum.
3. Uncheck all list and Select 'PRELOADER' only and press Download.
4. Remove battery from your phone, after 5 secs while pressing Vol + / Vol - or both, connect USB to you device. If you get no response from PC ( not recognize ), you have to unscrew and open your phone cover to manually jumper the 'Preloader Test point'. Please follow this guide here. However it's quiet advance step and please do it carefully at your own risk.:good:
5. Otherwise, after plug in USB, your PC will start installing Driver ( If it failed to install driver automatically, then you have to install it manually from VCOM Mediatek driver pack download earlier ).
6. If everything is right, SP flash tools will automatically detect your device via MTK USB port ( RED BAR PROGRESS ) and It will change it to Mediatek DA VCOM and PURPLE BAR PROGRESS show up and viola! GREEN CIRCLE popup!
DONE!
7. Now remove USB from your phone, Don't do anything yet, back to SP flash tools, and now Select all flash list except PRELOADER and press Download. and insert USB cable again and flash tools will start the process, wait until it finish flashing all img's ( Boot, Uboot, System, Data, MBR etc ).
If flashing processes done successfully, it will popup GREEN CIRCLE again, now you can take a deep breath :victory:
- Unplug USB > Put Battery ON > Press power button > You tell me what you feel :silly:
*Side Note : If you're having any issue like a boot loop, just boot into Recovery Mode and format data/cache and REBOOT.
CWM Recovery img here
*Automade using MTKDroidtools
Good Luck! :highfive::highfive:
Click to expand...
Click to collapse
Hi guys! I never knew that this would happened. So I just got my phone turned to something like this. i) The link above is not working. Do you guys have any spare links? ii) I tried as he said above, and I'm using this app that I found on YouTube, and I got DRAM error. I hope you guys could help me, I feel so bad towards myself. Thanks in advanced!

saladbass123 said:
Hi guys! I never knew that this would happened. So I just got my phone turned to something like this. i) The link above is not working. Do you guys have any spare links? ii) I tried as he said above, and I'm using this app that I found on YouTube, and I got DRAM error. I hope you guys could help me, I feel so bad towards myself. Thanks in advanced!
Click to expand...
Click to collapse
Hi saladbass,
DRAM error usually because of ROM isnt correct or in other words, it is not for your device. Try to find the correct ROM for your model.
try find here and let me know.
https://firmwarefile.com/lenovo-a850
good luck!:fingers-crossed:

RidzVarn said:
Hi everyone.
I got a Lenovo A850 ( MTK 6582 ) here which is belong to my friend, it was full with malware apps or I can say a Trojan, Hijackers etc etc.. Because it like to turn off USB DEBUGGING option ( checkbox ) and downloading inappropriate apps into device and I decide to flash a new ROM I downloaded from needrom website and flashed using SP Tools. All processes went alright and SP tools 'Green Circle' popup. :good:
Then, I unplug USB and put battery and cover, and pressing Power button. Sadly, it won't turn ON anymore, just Red LED light.:crying::crying: I can't even enter recovery / bootloader. I was looking for solutions everywhere including in X-DA forum. Some said, It was Hardware problem, but how come? It was fine before I flashed a ROM. and now it's totally dead
I played around by pulling out a battery and pressing Volume buttons + power with USB cable attached to it and it finally respond to PC device manager by showing a MTK USB port I tried using SP tools again to flash another ROM with hopes it will fix but yeah, I know it won't work as MTK USB Port is not the right driver for SP tools. :silly:
What do i do now? Please someone help me.
Many thanks!
EDIT : PROBLEM SOLVED
Hello members,
Finally, I got this device alive again and if you are also having this issue and still can't fix it, you can now by following below steps;
Its time to revive your dead phone.
First, download below files:
- Download this A850 stock ROM here ( MTK6582 )
- Use this SP flash tool, here
- VCOM Mediatek Drivers pack ( required )
*Items required : USB cable, PC/Laptop, & Your dead phone.
OK now lets start...
2. Unzip ROM file and start SP flash tools, Load scatter file > Go to option > check DA DL all with checksum.
3. Uncheck all list and Select 'PRELOADER' only and press Download.
4. Remove battery from your phone, after 5 secs while pressing Vol + / Vol - or both, connect USB to you device. If you get no response from PC ( not recognize ), you have to unscrew and open your phone cover to manually jumper the 'Preloader Test point'. Please follow this guide here. However it's quiet advance step and please do it carefully at your own risk.:good:
5. Otherwise, after plug in USB, your PC will start installing Driver ( If it failed to install driver automatically, then you have to install it manually from VCOM Mediatek driver pack download earlier ).
6. If everything is right, SP flash tools will automatically detect your device via MTK USB port ( RED BAR PROGRESS ) and It will change it to Mediatek DA VCOM and PURPLE BAR PROGRESS show up and viola! GREEN CIRCLE popup!
DONE!
7. Now remove USB from your phone, Don't do anything yet, back to SP flash tools, and now Select all flash list except PRELOADER and press Download. and insert USB cable again and flash tools will start the process, wait until it finish flashing all img's ( Boot, Uboot, System, Data, MBR etc ).
If flashing processes done successfully, it will popup GREEN CIRCLE again, now you can take a deep breath :victory:
- Unplug USB > Put Battery ON > Press power button > You tell me what you feel :silly:
*Side Note : If you're having any issue like a boot loop, just boot into Recovery Mode and format data/cache and REBOOT.
CWM Recovery img here
*Automade using MTKDroidtools
Good Luck! :highfive::highfive:
Click to expand...
Click to collapse
Bro, macam mana nak deal dgn error 4001 yg ckp da tak send respon dkt flash tool?

mfkofc said:
Bro, macam mana nak deal dgn error 4001 yg ckp da tak send respon dkt flash tool?
Click to expand...
Click to collapse
nada bunyi tu mcm SP Tools punya common error tu. Cuba guna wayar USB lain, reinstall MTK driver and guna different version SP tools. Dan 1 lagi .. pastikan ROM yg awk nk flash tu betul dengan model phone.
Gudluck bro :good:

Totally bricked a ZTE Blade L3, any solutions?

Hello,
tried to flash a custom OS and root on a ZTE Blade L3. I got CWM Recovery working and flashed a CM12.1 rom on it, after that, it failed to mount all partitions /cache etc. etc. then I restarted the phone and it bootloops + fades white immediatly!
Recovery or Bootloader etc. dont work
If I connenct the phone on my computer it connect, disconnnect, connect, disconnect and so on.
Anyone a solution or idea how I could save that?

I can help you, So first we have to know is it Hard bricked or just Soft bricked, In any case it's not hard to unbrick. Just follow these steps :silly:
1. Download SPFlashTool to your PC https://androidmtk.com/smart-phone-flash-tool
2.Download Drivers for MTK6582 (I hope I wrote the right MTK name) http://www.devfiles.co/download/0InO9P5m/MT65xx_USB_VCOM_DRIVERS.zip
3.Download stock firmware
http://r.srvtrck.com/v1/redirect?ur...ar&ad_t=advertiser&ad_zi=YieldLink&ad_dt=link
IF SOFT BRICKED:
-Update drivers with the one up there in the thread, Open SPFlashTool, Find scatter file (just a file with a .txt extension) and place it in Scatter file area in SPFlashTool (search on YouTube how to use SP), After you did that manually add the files that are missing ( it's usually the recovery and some other files that are missing), Then press download and AFTER that connected your phone with a USB cable! Then wait it to flash :victory: ,
IF HARD BRICKED:
-Remove battery,
-Connect to PC with USB cable
-It probably won't recognise your phone, so we need to enter so called META mode so we could flash the PRELOADER, to make the phone recognisable.
-To enter META mode remove battery( if you didn't), connect as I said up there, and try pressing and holding some buttons, I can't remember the correct combination that enters META mode but I think it was all buttons for 5 seconds, anyway you will know when you entered META mode if your PC recognises a change or if he finds the device :good:
-then enter SPFlashTool and flash the PRELOADER only (hope you know to use SPFlashTool)
-After that disconnect your phone and add battery
-Enter SPFlashTool and Flash whole system (all files except CACHE AND USER)
-You should be done ?
Hope it helps

Here's a total solution
https://androidfilehost.com/?fid=746010030569947486
Flash tool and stock ROM included. Just follow this:
1. unpack
2. run flashtool.exe
3. load scatter
4. click download
5. unplug your battery and plug the phone to your PC via USB
6. wait for process to finish and unplug your phone
7. Boot
P.S. I guess you'll need some drivers. Check the post above.
Good luck!

Database Info

welcome