My screen is cracked when i felt down on the stairs, there are some dent on the side which i think lead to a shock or impact to the screen...
i'm wondering how to check whether the glass break or the LCD panel break... i can still see display at the back perfectly, i confirm it with rotating the screen to see any black spots or any other issue, but it turn out to be fine. Also another problem is that the screen is not responding well... when i try to unlock, i place my finger and it dosent seem to detect it. But after a few tries, i managed to unlock it. For the screen unlocking i felt that the crackscreen may have impact on the touch screen sensor or so...
And i currently lives in malaysia and Asus service centre told me that the cost to repair the LCD and glass will be 800-1000!!! which is i cant afford due to i'm still currently a student.
SOME GOOD ADVICE NEEDED !!!
I'd assume that the LCD and the digitizer are glued together.
You should still have a warranty if you bought it, if you didn't you should of been more careful with it.
I didn't want a warranty because I knew I was going to root and unlock, so I bought a leather case for it.
Think of this as a life lesson.
Related
I am experiancing some problems!
basically I think the manufacturer installed protective screen has come loose from the hard sensor (due to use?) and so the stylus is pushing on an air bubble, and with the software keyboard (virtual keyboard) the wrong buttons are getting pressed.
I dont know whether to cut out that layer with a scalpel (carefully) and use normal screen protectors that stick properly ... has anyone done this before?
Maybe you could apply heat to it to tighten it or something I dont know so I need help!
My phone is an alpine (xda2i) but other pdas must be having the same issue?
is it ok to cut the initial plastic screen that comes integrated with the xda?
Just make sure it is actually a protective screen and not the digitizer (the membrane that makes it touch screen and sits on the LCD) that your cutting away.
with a protective skin there should be no need to cut anything... I honestly think your talking about the digitizer - in which case take to a mobile phone specialist and they could heat sync it for you.
To check whether it is the digitizer or the crappy screen protector, you should be able to see the edge of the layer at the side, especially manufacturer orginial screen protector, they are really crappy. You should be able to seperate the layer (from the edge) with something pointy (e.g. a needle), and then peel it off from there.
If you didn't see any distinguishable edge at the edge of the screen, chances are you should not do anything yourself.
Jonjamesm said:
Just make sure it is actually a protective screen and not the digitizer (the membrane that makes it touch screen and sits on the LCD) that your cutting away.
with a protective skin there should be no need to cut anything... I honestly think your talking about the digitizer - in which case take to a mobile phone specialist and they could heat sync it for you.
Click to expand...
Click to collapse
Thanks for the responses!!!
I have a feeling that it is what you are referring to as a digitizer. Do most of the mobile phone shops do this heat option? as after googling it, not much comes up, or is it referred to under a different terminology,
thanks in advance!
Rob
If your UK based you can find out more about them from apex laptops, google them...
I'm in Edinburgh, and it took me a while before I found someone willing to replace the digitizer.
This is not a common thing - but I think with the introduction of the iphone the markets for heat syncing will go up, I suggest freeing up an afternoon and go to some of those dodgy shops that offer the unlocking service, also some computer repair shop technicians might be confident in doing something of this nature.
Happy hunting!...
JJ McG.
thanks for your help
whatever you do dont approach o2. they are ridiculous, they want to charge 350 dollars to peel off the old one and put a new on one. search ebay and you will find digitizres with screwdriver and peeling, firming tool for 15 dollars plus postage.
o2's repair guys say it "original" spares which make it so expensive....
right...........
rang up
rang up a couple of shops one doesn't do heat sync and the other does but the machines bust, he started talking about soldering etc...(does that sound like it?) but when i re-described the problem he started talking about 50 60 quid for a new screen! which I am not prepared to pay for the relatively minor problem
How is a digitiser different from a normal screen protector anyway?
(placing a normal protector on top of it sort of helped reduce the problems because it applied a little firmness over the offending area....)
O.k the digitizer is not a screen protector. The Digitizer is a membrane that sits atop the LCD.
Note: that the LCD is not a touch screen and the only thing making your device a touch sensitive is this digitizer
digitizers can be pricey, but the reason your guy is costing it at 50 - 60 quid is because he is the middle man and needs to make a profit. You can find digitizers from apex laptops or GPS midlands (links below) and buy them at trade prices
http://www.gpsmidlands.co.uk/index.php?menu=Home
http://www.apexlaptops.co.uk/touchscreens.htm
Dependant on your device will depend on the price.
My guy asked for 10 pounds to replace my screen, which I thought was more than reasonable because if he broke the LCD whilst replacing the digitizer (which he did) he was liable to replace it. Make sure that your guy will do this.
hope this helps.
after googling...
After googling for a bit, I came across someone who had these sort of problems with their own pda
http://jamescrisp.blogspot.com/2007/05/fixing-palm-treos-digitizer-touch.html
it seems that dirt stuck under the sides can cause the same kinds of problems,
after running a bit of paper under the corners of the screen I have found some interesting results, the problems I have have changed slightly and seem to rectify temporarily when I press down (rub down) on the screen...
so I might look at taking it apart with some tools off ebay or something and giving it a good clean... any recommendations on how to strip down and clean an Alpine....? actually I'll repost that in the aline forum if there isn't already a post there....
hope your confident in doing so - I'd take it to a shop if it pisses you off that much - taking it a part and cleaning might end up with you just having a big screen phone with no touch pad...
Up to you, hope your successful
I searched the forums and google and couldn't find an image similar to what is happening to my fuze.
So yesterday I noticed a problem with my fuze screen, and i don't know if i can't explain the problem or what, but at&t is convinced it's damaged and will charge me a bunch if i even try to send it in.
There are no cracks, scratches, whatever. (I wish i could take a pic, but the only cam i have is the phone)
The problem is that the surface of the screen (I think the soft touch screen top) seems to have a thin layer of 'something' in there. It is the same shape as the screen, centered, and about 70% of the screen's size. The effect is something like the shimmer/rainbow from a very thin layer of oil on water. (thin film interference?) Anyways, the touch screen still works, the lcd still works, the glass isn't cracked, and I have no idea what happened. I use a screen protector and am very protective of my baby.
I'm thinking I need to order a new digitizer and replace that? ($25 and some labor doesn't sound bad after talking to AT&T about what i would get charged if they decide it's physical damage)
I dunno, if anyone has experience with damage like this or at&t or replacing digitizers and has any words to help me, either with explaining what happened or what i should do, that would be much appreciated.
I had the EXACT same problem on my fuze. It looked like the layers of the screen began to seperate. AT&T scared me that they would charge me for this so I sent it directly to HTC and they replaced the screen at no cost to me...took about 2 weeks.
AT&T Warranty agents are trained to be cautious in regards to damage to devices as the mail program doesn't leave much(any) option once you send the phone back for the exchange. It's either no-damage/no-charge or damage/charged, after which you cannot go back on the exchange.
My advice is to see if there is a Device Support Center in your area.
http://www.wireless.att.com/answer-center/main.jsp?t=solutionTab&solutionId=KB91429
I went to one with my possibly damaged Fuze and they took a look at it and exchanged it without any "possible" charges jargon.
If that isn't an option, you could buy a pre-paid phone to use while you send it in to HTC as TheSopranos16 did for repair.
Good luck!
Sir, the problem you have is this:
http://forum.xda-developers.com/showthread.php?t=439410
I only hope my xperia doesn't get it.
i have this same exact problem. its technically called a newton ring. att wanted $500 to fix it and the htc rep told me that whenever they encounter this they usualy dont cover under warenty because it is due to pressure on the screen and it would cost something like $300 to fix. so i basically said forget it and now im stuck with it.
Hello guys,
I've been using DHD for quite a long time and I never experienced any problems with this phone until I noticed the digitizer is cracked. I just took the phone out of my pocket and realised that it doesn't react when I touch the screen - there is a small crack in the corner. I think this is just the digitizer because the image is displayed correctly and there are also no scratches on Gorilla Glass (i also used screen protector). I have not dropped the phone recently (neither hit it with a hammer) and I'm wondering if it is possible that the digitizer has a factory defect and what about the warranty in such a case because when I heard what is the cost of repair...
Any clues guys? This is very important...
I had a similar problem with my screen.
The upper part of my screen was devastated with pieces of glass coming out regularly.Yet,the touchscreen worked.
Your case is pretty weird.I think you should take it to HTC and try to persuade them that its a defect if you're sure you haven't damaged it!
GoodLuck :good:
Hi,
first of all i will start with saying that I suppose I am not entitled to the official samsung warranty or customer service, as i bought my phone form ebay (unlocked version, shipped from Hong Kong). Unfortunately in my absence my younger brother managed to lightly scratch the screen when he was playing with it, he got scared and tried to get rid of the scratch by rubbing it with toothpaste (it's something he read on the internet, supposedly it was supposed to "polish" the light scratches and get rid of them). Of course it didn't work, and just made it worse. In fact it created a dull, round spot on the screen just where the scratch is, it was hard to clean and attracted moisture easily, moreover when screen was on you could notice a grainy/greasy spot. I guessed, that the toothpaste must've removed the oleophobic coating on the screen, so I thought i will buy a oleohobic coating kit, which i did. I went to Amazon and order the Crystalusion Liquid Glass, praying for it to fix it. After application it restored the hydro/oleophobic properties in that spot, and made it smooth just like the rest of the screen. Unfortunately the grainy/greasy effect while screen is on remained, and under direct light you can still see the dull spot, so i guess apart of removing the coating, he must've sanded the glass underneath it. I am thinking of putting a second layer of that liquid glass thingy, hoping it will fill the sanded pores, and smoothen the glass even more, maybe it will do the trick. It's not something that disturbs the every day usage, but i just cant get over the effect on the screen when its on .. and just the knowledge of not having a perfect, beautiful infinity display just after 3 weeks of having the phone is making me cry. And yes, I know i could use a screen protector .. I've tried those, and none of them suited me, first (samsung original) was not compatible with the case, and next two (wet application) ruined the screen quality (created that mentioned greasy/grainy effect on the entire screen), and after all the TGP reviews I decide just not to waste money on them, so i decided to go naked screen+case ... Do you think there any hope for me? Any ideas on how to fix it, or if it is even possible? Do You think that i can contact Samsung with a device bought on ebay? I will be grateful for any answer, and sorry if this is not the right place for this kind of thread.
Well it won't be covered udner warranty because it's damage caused by you. It's not a faulty product.
But you can maybe have it repaired by Samsung. They can replace the display with a new one. But this is quite expensive.
Putting a screen protector on might help mask the marks on the screen and make them less noticeable.
Hi, I have recently dropped my S7 and my screen broke, but it’s only smal black dot on side of amoled and one line trough glass. My biggest problem is that lower part of screen digitizer stoped working. I’ve searched all over ebay for new screen assembly with amoled and digitizer but it’s expensive ~170$. So I was thinking, can I replace only digitizer, they cost about 30-50$? I’m not sure because every video on YouTube that replaced only digitizer had fully working amoled. Do you guys have any experience? Any advice is appreciated
Hello,
As seen on some drop test videos, sometimes screen can be totally messed up but digitizer can still be working good. So my guess is that they work independently and so a new digitizer could work good even if the screen as some dead areas or lines etc...
But due to the fact that Samsung glue the glass with the digitizer and with the screen panel, it's a very difficult process to just remove the glass without scratching or breaking the Amoled panel. Better be well prepared to it, have the right tools and have a lot of dexterity and patience. It's already a big pain to separate the screen for the glass, so if you're planning to separate and replace only the digitizer, then good luck :-/
Before trying this, you still should call some repair centers to see how much it would cost for a screen replacement, but unfortunately it is most likely to be expensive. Also, be aware that buying yourself a screen replacement doesn't guarantee you that it will be an Amoled. A year ago, my brother broke his OnePlus 3 screen, and it was almost impossible to find an Amoled screen replacement, their description was saying Amoled, but by reading well, we could always find somewhere "TFT" or "LCD" which are not Amoled.
In the end, you have to be aware than any flagship phone cost an arm to repair, especially the screen as everything is glued and made for you not to be able to repair it yourself. So it is very highly recommended to protect your phone with cases and screen protectors (plastic screen protectors protect the screen better from shocks than glass screen protectors, even if plastic feels cheaper). Unless you have a lot of money and can easily pay a repair, protect your phone!
Sorry, that's all I can do for you...