hi there
After flashing a stock room I got a boot bucle, so i did reset data factory, cache partition and dalvich cache, restart and still had a boot bucle, so I enter in dowload mode again started odin and reflashed stok room 2.3.4 again; in the midle of the process i got an odin FAIL on red square !!!! after that fit doesnt even start, is dead.
I am still able to enter "dowload mode" by holding all three bottons (volume up/down. home and power) but when i tray to flash someting odin get stuck on <1> setup conection .....
any idea what i can do??
Try rebooting the PC and changing the USB port!...Hope it works!
galaxy fit + CM7.2 (2.3.7) + 801Mhz
neil.richard said:
Try rebooting the PC and changing the USB port!...Hope it works!
galaxy fit + CM7.2 (2.3.7) + 801Mhz
Click to expand...
Click to collapse
I have been restared many times and tryed every single usb port and doest work, but thanks for anwser
any body else, any idea ??
Try it from another pc, if possible. Might be internal hub problem of pc. At least you could exclude this after it.
Sent from my GT-S5570 using XDA App
Rodsengard said:
Try it from another pc, if possible. Might be internal hub problem of pc. At least you could exclude this after it.
Sent from my GT-S5570 using XDA App
Click to expand...
Click to collapse
i al ready try on 3 diferent pc`s and every port on them and still the same. any advice is welcome
Okay, you may try flashing creed's 1.3 using odin and then flash v1.5 over it...
Creed' s rom is any day better than the stock rom...
And if you want the stock rom only, you could redownload all your files...maybe that will help...
mefrodo said:
I have been restared many times and tryed every single usb port and doest work, but thanks for anwser
any body else, any idea ??
Click to expand...
Click to collapse
Can u go in Recovery mode?...if yes then u can either flash Creed's ROM or CM7!...
galaxy fit + CM7.2 (2.3.7) + 801Mhz
neil.richard said:
Can u go in Recovery mode?...if yes then u can either flash Creed's ROM or CM7!...
galaxy fit + CM7.2 (2.3.7) + 801Mhz
Click to expand...
Click to collapse
Odin does recognize the phone but, when i try ti flash any room it gets stuck on "set up conection..." after 45 minutes still same status.
help please!!!!
mefrodo said:
Odin does recognize the phone but, when i try ti flash any room it gets stuck on "set up conection..." after 45 minutes still same status.
help please!!!!
Click to expand...
Click to collapse
Okay, now some basic stuff...
Do you have a galaxy fit s5670??
And are you trying to flash galaxy fit's software only na???
And have tried taking out the battery, putting it back and restarting your phone??
also, while your phone is switched off, and you try to charge it, does the big battery icon come up???
a.cid said:
Okay, now some basic stuff...
Do you have a galaxy fit s5670??
And are you trying to flash galaxy fit's software only na???
And have tried taking out the battery, putting it back and restarting your phone??
also, while your phone is switched off, and you try to charge it, does the big battery icon come up???
Click to expand...
Click to collapse
thanks for for you answer
I have S5670
I am tryng to flash a stock room for s5670
I got nothing on screen, not even pulged
only way that odin recognize the phone is by holding volume up/down home and power, when press start button on odin it get stuck on firs step: "set up conection ... " and nothings happen after that
any idea is welcome ill try everyting
mefrodo said:
thanks for for you answer
I have S5670
I am tryng to flash a stock room for s5670
I got nothing on screen, not even pulged
only way that odin recognize the phone is by holding volume up/down home and power, when press start button on odin it get stuck on firs step: "set up conection ... " and nothings happen after that
any idea is welcome ill try everyting
Click to expand...
Click to collapse
The fact that odin recognizes your phone means that it isn't a hard brick..
If all else fails, try asking samsung for a replacement..
Say you left the phone to charge overnight and now it rrefuses to switch on...however, this should be your last resort...
Before that, can you list in detail, all the steps you did...like which odin, which ops etc...
And was your device able to connect to ur pc before you tried this, as in all drivers were present??
Also, maybe you can try flashing cwm from this:
http://forum.xda-developers.com/showthread.php?t=1352518
a.cid said:
The fact that odin recognizes your phone means that it isn't a hard brick..
If all else fails, try asking samsung for a replacement..
Say you left the phone to charge overnight and now it rrefuses to switch on...however, this should be your last resort...
Before that, can you list in detail, all the steps you did...like which odin, which ops etc...
And was your device able to connect to ur pc before you tried this, as in all drivers were present??
Also, maybe you can try flashing cwm from this:
http://forum.xda-developers.com/showthread.php?t=1352518
Click to expand...
Click to collapse
thanks for your answer, I will be writing all details at night due to I am working rigth now, also I`ll check the link a soon as I can. thanks in advance.
If the conection problem is... Before u usw odin plz make sure that u have instal lates kies on your pc/laptop...have u made it...and than if u usw windows xp plz make sure went u instal kies there are dotnet fix v 3.5 or 4 on your pc....usually kies will download it for u.....when u install it
I've try to flash frm my pc that use windows xp sp2 and doesnt have internet conection and i use kies from the cd boxlet it doesnt work... I think ww have the same problem... May it help u......
Sent from my GT-S5670 using xda premium
And a big sorry for my terible english....... (●*∩_∩*●)
i think your problem is :
1: you do t have the latest dotnet fix......
2. your kies is not ip to date or u even doesn't install it....
3. or your antivirus block the acces.so plz stop all of your antivirus begore flasing use odin...
4. u have usb problem..plz search on it..im not master about it... im just a new kid on the block lol (︶︿︶)
the thing that should u do....
1. check your version of wi diws and dotnet fix.
2. stop all of your antivirus....
3. try reinstal kies first and update it....than run your odin....
Sent from my GT-S5670 using xda premium
I have the same problem... I've tried everything... I don't know what else to do (
reizen said:
I have the same problem... I've tried everything... I don't know what else to do (
Click to expand...
Click to collapse
Im not master bout it.but before trying can u write here soec of your pc....
Sent from my GT-S5670 using xda premium
sorry .... can be more explicit ... I do not know very well English
Haha lol sorry there somany eror on what i've type
Sent from my GT-S5670 using xda premium
reizen said:
sorry .... can be more explicit ... I do not know very well English
Click to expand...
Click to collapse
Can you share your pc spec here.... Cause i think the problem is not on the odin but your pc software..
Sent from my GT-S5670 using xda premium
problem solved... thanks for help!
... was due to the USB port, I did not have USB 2.0 port
Related
Hello!
I got a small problem with a galaxy fit. It does power on and it shows a computer and a phone with an exclamation mark between them.
The only thing that is accessible is the download mode.
Now in download mode odin gets stuck at "mibib download.." and it just keeps counting the time.
Does anyone have a clue about what to do to get the phone working again?
P.S.
This is my friends phone and i wasn't with him when the accident happened, but i understood that he might have tried cu flash something and Odin got stuck and he pulled the cable.
Thank you.
you must also come into recovery ...
if you cant flash it with odin 4.38 ... (in download-mode)
Than you make an data wipe/reset and wipe the dalvik...
And the phone is not bricked
n00b.androidDEV said:
you must also come into recovery ...
Click to expand...
Click to collapse
Can you please be more specific about this procedure? I'm not familiar with it.
Also a link to a tutorial would be greatly appreciated.
Thank you.
Can you come in recovery?
Press Power On + Home Button at once
If i press home+power it shows the same logo as just trying to switch on. I cannot use the recovery menu.
viperasp said:
If i press home+power it shows the same logo as just trying to switch on. I cannot use the recovery menu.
Click to expand...
Click to collapse
Try reinstalling the system. Press 3 buttons together. Power On + Home + volume Down. Prepare all the in Odin, connect phone with your PC, and Start in Odin.
cant we use odin_multi_downloader_v4.42 , beni.ops . why it must be odin 4.38 . are there any diferences
have you used odin 1.7 or 1.8?
galaxy tab versions!!
bcoz in my galaxy tab it comes when
odin fails!
but i can solve that problem by flashing
(dbdata.tar)file!!! only in mySAMGUNG
GALAXY TAB 7 ,not tried 4 fit yet ,but
with galaxy TAB it works,
you just have to do is put(dbdata.tar)in
the first of the Odin blank row that is
(PDA)and connect Tab to pc and press
"Start"
only works for galaxy TAB ,dont knw
abt fit!!!!
but 100% work for Tab
u can try this on fit ,i dont knw wat will happen!
it may work!!
djozaa said:
cant we use odin_multi_downloader_v4.42 , beni.ops . why it must be odin 4.38 . are there any diferences
Click to expand...
Click to collapse
I use Odin 4.38, and use Beni v1.0.ops. When on the phone display a yellow triangle to download I connect the phone to the computer and when the port is detected I click on Start and wait until it's over, and that to me takes about 5 minutes. When it is almost square in the port is blue.
may b u can use unisoft unbrick....just google it out..
i wil provide u wid some more info if u can just tel me if u can enter in recovery mode nd by the way wat recovery it is...the stock i mean samsung 1's or the clockworkmod recovery.....
I too faced similar problm..did u flash in windows 7??coz i had the same prob on win 7 then flashed in xp n worked..u must be admin inorder to use odin hope it helps u
vijayanandssj4 said:
I too faced similar problm..did u flash in windows 7??coz i had the same prob on win 7 then flashed in xp n worked..u must be admin inorder to use odin hope it helps u
Click to expand...
Click to collapse
To Odin work should be installed by the driver when the phone is connected to the computer. If you can not install the driver, Odin can not work, not port may be to open.
ZmisiS said:
To Odin work should be installed by the driver when the phone is connected to the computer. If you can not install the driver, Odin can not work, not port may be to open.
Click to expand...
Click to collapse
Hey bro by drivers do u mean samsung drivers???if yes then i do have samsung drivers in win 7 but still doesnt flash..win7 sucks it has more administration rights problems
viperasp said:
Hello!
I got a small problem with a galaxy fit. It does power on and it shows a computer and a phone with an exclamation mark between them.
The only thing that is accessible is the download mode.
Now in download mode odin gets stuck at "mibib download.." and it just keeps counting the time.
Does anyone have a clue about what to do to get the phone working again?
P.S.
This is my friends phone and i wasn't with him when the accident happened, but i understood that he might have tried cu flash something and Odin got stuck and he pulled the cable.
Thank you.
Click to expand...
Click to collapse
if ur sure it wont work...it may be surely bricked ..l had bricked too..fortunately..my fone's warranty was active...i gave to the samsung centre....they changed my motherboard for free due to the warranty!
vijayanandssj4 said:
Hey bro by drivers do u mean samsung drivers???if yes then i do have samsung drivers in win 7 but still doesnt flash..win7 sucks it has more administration rights problems
Click to expand...
Click to collapse
I have Windows 7 x64 and it is OK. On Odin you need go as Administrator. Drivers are installed automatically for me when I connect the phone and computer.
ZmisiS said:
I have Windows 7 x64 and it is OK. On Odin you need go as Administrator. Drivers are installed automatically for me when I connect the phone and computer.
Click to expand...
Click to collapse
Hmm i too have an admin account on win7 x64 still odin doesn't work for me...
vijayanandssj4 said:
Hmm i too have an admin account on win7 x64 still odin doesn't work for me...
Click to expand...
Click to collapse
Right click on Odin ...
Turn off your cell phone, press 3 buttons at once: Menu + Power + Down Sound, wait until the phone display a yellow triangle appears to download, when it appears, connect your phone to your computer and you should get this:
Fit goes to bootloop after flashing stock firmware
ZmisiS said:
Try reinstalling the system. Press 3 buttons together. Power On + Home + volume Down. Prepare all the in Odin, connect phone with your PC, and Start in Odin.
Click to expand...
Click to collapse
I flashed stock firmware using odin and it successfully got completed but after rebooting it gets stuck on samsung logo and goes into bootloop. Can u help me to recover my fit....
vijayf5 said:
I flashed stock firmware using odin and it successfully got completed but after rebooting it gets stuck on samsung logo and goes into bootloop. Can u help me to recover my fit....
Click to expand...
Click to collapse
goto recovery and wipe data & cache
remove bettery and switch it on again..
vijayf5 said:
I flashed stock firmware using odin and it successfully got completed but after rebooting it gets stuck on samsung logo and goes into bootloop. Can u help me to recover my fit....
Click to expand...
Click to collapse
Go in Recovery and it is enough to do the wipe data / recovery and reboot.
In Recovery you can go in a way that together press Home and Power buttons.
i am in trouble guys..i have been using miui since v4..whenever i wanted to revert to stock it was too hard to connect it to PC(windows 7) via usb. i tried 10-15 times.plugged unplugged plugged unplugged and at least i managed to connect and flash via odin...but yesterday i downloaded miui v10,1 and flashed.everything was fine.but the was too hot because of vurrut v4.. i flashed ganesh uc port for miui(kernel).and rebooted.but phone cant pass i9003 galaxy scl logo. and i cant access CWM..but i can enter download mode. the Problem is that i cant connect via usb to pc..everytime Your device is not recognised..even i download usb drivers for samsung. i even tried android sdk google revision usb pack 4 ..cant connect.what to do?
You mean the button combination can't boot into recovery?
Cheers
Sent from my GT-i9003 powered by MIUI
actually i dont need to boot into recovery) i can enter in download mode.but the problem is that after entering download mode i connect the usb. and on pc appears this: Usb device not recognised...
for this time i iam luckly..but the next time when i want to install MIUI cm7 again i will face this problem again...i would like to know how to solve it
Just boot to recovery and factory reset you should boot
Cheers
Sent from my GT-i9003 powered by MIUI
Install the latest Samsung USB Drivers. And you should plug in the usb cable directly to pc and not on the USB extension. Try this link. They are compatible with I9003
http://forum.xda-developers.com/showthread.php?t=961956
I cannot send sms rom：v10.1 miui
where is CWM in MIUI? how can i restore all my data?
While other roms have recovery option i do not find this in MIUI?
I seriously want to enjoy MIUI.....
please help
vivekanandrc said:
where is CWM in MIUI? how can i restore all my data?
While other roms have recovery option i do not find this in MIUI?
I seriously want to enjoy MIUI.....
please help
Click to expand...
Click to collapse
Look for the backup app in Tools. There you can restore your system.
same problem here
erbao1210 said:
I cannot send sms rom：v10.1 miui
Click to expand...
Click to collapse
Hi Sir,
Im having the same problem too, is there a solution to it? im on xxkpu using miui v10.2 thanks!
rxt5150 said:
Hi Sir,
Im having the same problem too, is there a solution to it? im on xxkpu using miui v10.2 thanks!
Click to expand...
Click to collapse
I have been sending 200 texts per day and i am on MIUI v 10.2 xxkpq.
Try that.
texts
rockyddroid said:
I have been sending 200 texts per day and i am on MIUI v 10.2 xxkpq.
Try that.
Click to expand...
Click to collapse
for now sir i"ve been using go sms pro and not the stock messaging app in miui and I must say sending msgs is a breeze.. Thanks anyway!
Problem solved. Problem was the Usb cable itself.after changing everything worked.
Sent from my GT-I9003 using XDA
Found the solution
Nightwish sgsl said:
i am in trouble guys..i have been using miui since v4..whenever i wanted to revert to stock it was too hard to connect it to PC(windows 7) via usb. i tried 10-15 times.plugged unplugged plugged unplugged and at least i managed to connect and flash via odin...but yesterday i downloaded miui v10,1 and flashed.everything was fine.but the was too hot because of vurrut v4.. i flashed ganesh uc port for miui(kernel).and rebooted.but phone cant pass i9003 galaxy scl logo. and i cant access CWM..but i can enter download mode. the Problem is that i cant connect via usb to pc..everytime Your device is not recognised..even i download usb drivers for samsung. i even tried android sdk google revision usb pack 4 ..cant connect.what to do?
Click to expand...
Click to collapse
Hi,
Just go to SwapSD and select 'Swap'. This will mount the sdcard. This has got nothing to do with the USB cable or the drivers. Enjoy!
Went to flash a rom and my dog ran past the PC and the cable got unplugged.Now all i can get on the phone is..
Firmware encountered an issue.Please select recovery mode in Kies & try again..
Wasn't using Kies was using Odin.and nothing will recognize the phone now..
Above the message i have a image of a phone Download triangle and a PC..
Any ideas?
Thanks
Dale362 said:
Went to flash a rom and my dog ran past the PC and the cable got unplugged.Now all i can get on the phone is.. Firmware encountered an issue.Please select recovery mode in Kies & try again..Wasn't using Kies was using Odin.and nothing will recognize the phone now.. Above the message i have a image of a phone Download triangle and a PC..Any ideas? Thanks
Click to expand...
Click to collapse
Yes...kill the dog...quietly take it for a long walk....jkking
does it look like this...
that is still download mode you can use this the one click to take it or reload it....
if you get that message it is still being recognized ok...
you can also read the thread that i provide below...
http://forum.xda-developers.com/showthread.php?t=1524081
more reading for you...sir
http://forum.xda-developers.com/showthread.php?t=1424504
When i plug it back into the PC it says "USB device not recognized" ?
Odin nor Heimdall see it either..
yes looks like that a little different but close enough.. Thanks
Dale362 said:
When i plug it back into the PC it says "USB device not recognized" ?
Odin nor Heimdall see it either..
yes looks like that a little different but close enough.. Thanks
Click to expand...
Click to collapse
try diff usb port...try running it the odin
nothing is seeing the phone... Crappola..
Dale362 said:
nothing is seeing the phone... Crappola..
Click to expand...
Click to collapse
keep trying...it does take a few tries...to go into dl mode, and then for the pc to id it...
bigjoe2675 said:
keep trying...it does take a few tries...to go into dl mode, and then for the pc to id it...
Click to expand...
Click to collapse
Trust me.. I am working on it... Thanks man..
Maybe something...
In Odin i got it to show 0:[COM8] in ID:COM.. Is that what i want to see?
P.S. NVM I got it flashing now... Thanks man...
Dale362 said:
Maybe something...
In Odin i got it to show 0:[COM8] in ID:COM.. Is that what i want to see?
Click to expand...
Click to collapse
yes.. i hope it comes below the first big square on the top left on a yellow background right?
i think your odin recognize the phone. can you post a pic just to be sure.
Worked... Phone is rebooting now... Thank you Jesus......lol
Dale362 said:
Worked... Phone is rebooting now... Thank you Jesus......lol
Click to expand...
Click to collapse
See....glad it worked out
Dale362 said:
Worked... Phone is rebooting now... Thank you Jesus......lol
Click to expand...
Click to collapse
Good..
Tried all the usb ports on my desktop. Every port says "Usb device not recognized"
Any workaround?
Try a different cord. Happened to me like that once.
Sent from my SGH-I997 using xda app-developers app
csandman1977 said:
Try a different cord. Happened to me like that once.
Sent from my SGH-I997 using xda app-developers app
Click to expand...
Click to collapse
Different cord worked like a charm. thanks.
I need help also. I was trying to put in a new rom on the computer (I know i shouldn't have done that) anyways after i was trying to install the rom my phone got stuck on the Samsung Logo and when I try using Odin and putting my phone in download mode my computer doesn't regonize my phone, it just says unknown devices. I need help on restoring my phone back to normal. I want to unbrick it to stock
LHT92 said:
I need help also. I was trying to put in a new rom on the computer (I know i shouldn't have done that) anyways after i was trying to install the rom my phone got stuck on the Samsung Logo and when I try using Odin and putting my phone in download mode my computer doesn't regonize my phone, it just says unknown devices. I need help on restoring my phone back to normal. I want to unbrick it to stock
Click to expand...
Click to collapse
Try with a new cable as I did & then follow my video tutorial Video Tutorial - Samsung Infuse 4G back to stock Froyo 2.2.1 (I997UCKD5+Root+3e)
All the best
Was trying to root my galaxy sl, was taking too long so i decided to take out the battery, since then phone has refused to come on or communicate with my pc.
Please guys what can I do about it
can u switch ur mobile to recovery or downloading mode?
''Hit THANKS if this post helps u in anyway''
jonkuru said:
Was trying to root my galaxy sl, was taking too long so i decided to take out the battery, since then phone has refused to come on or communicate with my pc.
Please guys what can I do about it
Click to expand...
Click to collapse
Try going into download mode on your i9003 and flashing a stock 3 file firmware in odin
BassBlaster said:
Try going into download mode on your i9003 and flashing a stock 3 file firmware in odin
Click to expand...
Click to collapse
@Timothyjo, The phone does not power on, cant get it to recovery mode and it does not respond when connected via usb to my pc
jonkuru said:
@Timothyjo, The phone does not power on, cant get it to recovery mode and it does not respond when connected via usb to my pc
Click to expand...
Click to collapse
Try clicking the reset button (between speaker and camera) while trying to access download mode, keep trying until you succeed.
Can you tell me which thing you tried to flash (the thread), if you flashed i9000 firmware your phone is completely DEAD and needs to go to the service center.
Skander1998 said:
Try clicking the reset button (between speaker and camera) while trying to access download mode, keep trying until you succeed.
Can you tell me which thing you tried to flash (the thread), if you flashed i9000 firmware your phone is completely DEAD and needs to go to the service center.
Click to expand...
Click to collapse
reset button ?? what s that ?? i cant find it ! LOL ! .. and i flashed i9000 firmware is the usb JIG will work or NOT ????
galaxyskaram said:
reset button ?? what s that ?? i cant find it ! LOL ! .. and i flashed i9000 firmware is the usb JIG will work or NOT ????
Click to expand...
Click to collapse
Open ur pannel and open the inner pannel with screwdriver or something there u find the hard reset button
u need a third person to do this u have to press volume- button , home button , reset button and power button at the same time
''DO IT AT YOUR OWN RISK''
---------- Post added at 03:04 AM ---------- Previous post was at 02:50 AM ----------
is ur phone showing a symbol like bellow
phone symbol + caution + computer
galaxyskaram said:
reset button ?? what s that ?? i cant find it ! LOL ! .. and i flashed i9000 firmware is the usb JIG will work or NOT ????
Click to expand...
Click to collapse
its already dead man coz u flash a wrong firmware only sammy can revive it..or try the one that us said the USB jig
galaxyskaram said:
reset button ?? what s that ?? i cant find it ! LOL ! .. and i flashed i9000 firmware is the usb JIG will work or NOT ????
Click to expand...
Click to collapse
You're screwed... A jig won't help I think... U can try though
Sent from my GT-I9003 using xda app-developers app
dout i9003
hey i have rooted my phone with cf root and how to unroot
navinash.avi said:
hey i have rooted my phone with cf root and how to unroot
Click to expand...
Click to collapse
try this link: http://forum.xda-developers.com/showthread.php?t=1331253
there is a flashable zip there just download it and flash via CWM and it will unroot ur phobe..
press thanks button if i helped u.
nobody to answer ????
Hi there
I have tab2 7.0 3113 4.1.1 OTA JR003C.P3113UECLK7
device uses JB right??
I just cant manage to install CWM through odin....it seems to start but no response...
tried single step samsung cwm root etc but NO WAY......JUST MADE ME CRAZY
can someone help to get rid of this problem !!!
would app. alot
thanks in advance
bodomar said:
nobody to answer ????
Hi there
I have tab2 7.0 3113 4.1.1 OTA JR003C.P3113UECLK7
device uses JB right??
I just cant manage to install CWM through odin....it seems to start but no response...
tried single step samsung cwm root etc but NO WAY......JUST MADE ME CRAZY
can someone help to get rid of this problem !!!
would app. alot
thanks in advance
Click to expand...
Click to collapse
ok go to your settings and under the developer option tab make sure tha usb debugging is clicked. that should allow you to install cwm.
guncrasher said:
ok go to your settings and under the developer option tab make sure tha usb debugging is clicked. that should allow you to install cwm.
Click to expand...
Click to collapse
tried it but didnt help ...
Re: [Q] How to enable mobile calls on p3105
You need triangle away to reset the flash counter to 0. You can get it (paid) in play store or for free here in xda.
Sent from my SCH-I535 using xda premium
bodomar said:
nobody to answer ????
Hi there
I have tab2 7.0 3113 4.1.1 OTA JR003C.P3113UECLK7
device uses JB right??
I just cant manage to install CWM through odin....it seems to start but no response...
tried single step samsung cwm root etc but NO WAY......JUST MADE ME CRAZY
can someone help to get rid of this problem !!!
would app. alot
thanks in advance
Click to expand...
Click to collapse
Hey there, didnt know if your problem was solved so ill give a few steps that I did after the ota 4.1.1 update
First let the device reboot and optimize. Then turn off. Hold the vol- and power hard buttons to put it in download mode.
Download cf-auto-rood from hear on xda, and odin if u need it, also I find that the samsund updater/push notify dosent go cracked out if u have triangle away...
Install kies from samsung, then stop the program through your task manager.
Plug in the gtab2 and wait for the notification that the device is identified, double check that kies is not running, start up odin and flash the cf-auto-root through, I believe the thread will give u which option to flash. Let it reboot.
If it hange at the boot do a hard reboot and plug in the power cable let it charge then boot it up.
If all goes well you'll be rooted with busybox, then install cwm through the market then flash the recovery.
Its a long process but its worked for me about 4 to 5 times after reflashing the stock tar file I got from a when the first root was done for the gtab2. Hope it helps you or anyone else...
Sent from my GT-P3113 using Tapatalk HD
sickysticky said:
Hey there, didnt know if your problem was solved so ill give a few steps that I did after the ota 4.1.1 update
First let the device reboot and optimize. Then turn off. Hold the vol- and power hard buttons to put it in download mode.
Download cf-auto-rood from hear on xda, and odin if u need it, also I find that the samsund updater/push notify dosent go cracked out if u have triangle away...
Install kies from samsung, then stop the program through your task manager.
Plug in the gtab2 and wait for the notification that the device is identified, double check that kies is not running, start up odin and flash the cf-auto-root through, I believe the thread will give u which option to flash. Let it reboot.
If it hange at the boot do a hard reboot and plug in the power cable let it charge then boot it up.
If all goes well you'll be rooted with busybox, then install cwm through the market then flash the recovery.
Its a long process but its worked for me about 4 to 5 times after reflashing the stock tar file I got from a when the first root was done for the gtab2. Hope it helps you or anyone else...
Sent from my GT-P3113 using Tapatalk HD
Click to expand...
Click to collapse
thanks ....
i ll give it a try next week when tab is back from holiday
Hope it helps
Sent from my GT-P3113 using Tapatalk HD
sickysticky said:
Hope it helps
Sent from my GT-P3113 using Tapatalk HD
Click to expand...
Click to collapse
it didnt work either ....so strange,no response
please see the photo attached...
Did u stop kies in the process manager before starting odin and after the tab is connected?
Sent from my GT-P3113 using Tapatalk HD
sickysticky said:
Did u stop kies in the process manager before starting odin and after the tab is connected?
Sent from my GT-P3113 using Tapatalk HD
Click to expand...
Click to collapse
thanks all finally managed after plugging and unplugging usb cable several times...
but now I have a worse problem....
after rooting the device I copied wpa_supplicant file to system/bin ,I tried to add ad-hoc support to connect to nokia e72
but while I was doing that I probably damaged some files in system/bin
now wifi is gone....device tries to open wifi but no response !!!
please advice what to do ((
I would sugest, wrtie notes on what u did, n start from scratch....
A clean filesystem can be monitored better, especially if ur modifying system files
:thumbup::beer::thumbup:
Sent from my GT-P3113 using Tapatalk HD
sickysticky said:
I would sugest, wrtie notes on what u did, n start from scratch....
A clean filesystem can be monitored better, especially if ur modifying system files
:thumbup::beer::thumbup:
Sent from my GT-P3113 using Tapatalk HD
Click to expand...
Click to collapse
i copied wpa file to download file then navigated to system/bin
pasted wpa file there....
after i saw it didnt work i deleted it
in system/bin i opened some files with text editor etc.....
added adb shell(by mistake) then deleted...
(