Database Info

HELP!!! my Uni stucks in bootloader

Hello to all uni gurus and wizards!!
First of all, I've read all wiki before posting this question. Perhaps i"ve missed something but honestly, i did my best.
Now to the problem: I've got QTEK9000. For couple of years I've enjoyed the brilliant ROMS that were developer here by masters . Recently my uni's motherboard went dead, so i find a person (it was not easy) who replaced it. That person flashed my device with original WM5, and it worked perfectly and i've got videocalls also
Well then I decided to re-flash uni with WM6. And there was when problems started. I started with Tomal's 8.71 ROM, but it was unable to detect my Uni at all!!! Tried Tomal's 8.9 - same thing, VNInt's ROM - no good. I've tried MaUpgradeUt_noID.exe and it founded uni, but after restart device stacks in bootloader. My bootloader is v.1.01 and is says 'Serial' on screen, even though it is connected through USB cable. That is OK because previously (before MB replacement) it was showing 'Serial' but I was able to flash without any problem.
So now I have my Uni with Bootloader v.1.01 and 'Serial' written on it. I've tried to connect with Mtty utility and with Uni_exitbootloader, but they can not see that USB port is connected to Uni - 'Cannot open USB port'.
Thank you for reading so much letters Any help will be greately appreciated

Have you done a Doc format?
I´m posting thsi thread to have more helpfull material:
http://forum.xda-developers.com/showthread.php?t=549207
Hope it helps,

orb3000
Yes, I've tried DOC format, but mtty utility can not find USB port. All I get is COM1 and COM2

Sorry I can´t think on other solution...
But I´m sure later someone will give you a light

have you made sure active sync isn't using USB (untick in connections on PC first)

Hey -Jonny- friend!
Nice to see you´re back!
Cheers,

what has happened?
BesoC said:
orb3000
Yes, I've tried DOC format, but mtty utility can not find USB port. All I get is COM1 and COM2
Click to expand...
Click to collapse
Did the metod of jonny´s advice works? "cancel the active sync usb conection first, before conect the UNi to PC," then open mtty and try tak 28 55aa.

-Jonny- said:
have you made sure active sync isn't using USB (untick in connections on PC first)
Click to expand...
Click to collapse
Absolutely. I've untick USB in ActiveSync connections. I've even killed ActiveSync processes wcescomm.exe and rapimgr.exe. Unfortunately, mtty can not see USB port at all.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

1. have you check usb cable? perhap your cable brocken. try another usb cable.
2. wish you have the lattest active sync (4.5), try to uninstall it then re-install. restart you pc then try to flashing.
3. try with another pc - or - try first to restore your pc to the date you remember the last date that everything fine when you flashing.
hope one of that will solve your problem ... or we must wait for enlightenment from uni master sifu here

indrastrid said:
1. have you check usb cable? perhap your cable brocken. try another usb cable.
2. wish you have the lattest active sync (4.5), try to uninstall it then re-install. restart you pc then try to flashing.
3. try with another pc - or - try first to restore your pc to the date you remember the last date that everything fine when you flashing.
hope one of that will solve your problem ... or we must wait for enlightenment from uni master sifu here
Click to expand...
Click to collapse
Thank you for reply These are good suggestions. However, I've already tried them - installed AS 4.5 on a different computer, changed cable (though I'm pretty sure that old one is working) and tried to run mtty on that computer. The same thing - computer does not recognises USB device and mtty cannot see USB port

disable AS usb connection as Jonny advised. now connect the usb cable and try to flash a rom. it will make sure that your usb port/cable is working right. wait to finish the flashing, exit RUU.
now disconnect the cable and reconnect. run the mtty tool...

make sure usb cable plugged into computer, not into hub. i didn't need to kill anything for mine to work. reboot pc and try again?

tomal said:
disable AS usb connection as Jonny advised. now connect the usb cable and try to flash a rom. it will make sure that your usb port/cable is working right. wait to finish the flashing, exit RUU.
now disconnect the cable and reconnect. run the mtty tool...
Click to expand...
Click to collapse
Wow, Gurus are here Now, what i did:
1. I've get a desktop with fresh WindowsXP SP3 installed.
2. Installed AS 4.5 from MS website
3. Disabled USB connections in AS
4. Removed SIM card and SD card from my UNI.
5. Connected my UNI directly to computer with definately working USB cable. Got message "One of USB devices has mulfunctioned........"
6. Tried to flash with Tomal's 8.9 ROM for 64MB. It was unable to see my UNI:
Of course flashing was unsuccessfull
Also MTTY 1.42 utility cannot see USB port
After all this my UNI still stucks in bootloader wth text 'Serial' on the top and 'v1.01' at the bottom

seems your usb port is broken.

tomal said:
seems your usb port is broken.
Click to expand...
Click to collapse
USB port on UNI? I will check. However, I doubt it, because when I plug mY UNI in computer Windows detects something on USB port, but cannot identufy it. If USB port were broken, then Windows would be unable to detect anything.

I guess, there's no solution for my case . Thanks to all who was trying to help me

[Q] alcatel one touch 906 ROM

Hi to all. I just recently rooted my alcatel one touch 906. Is there a compatible ROM for my device. Here is my device info, for reference.:
Model: alcatel one touch 906
Processor: Qualcomm msm7227
RAM: 512
Android 2.2.1
Build: fsr.1.3.6.0_t10.16
Thanks in advance. I hope you can help me..

thread updating..anyone?? thanks..

My Alcatel T906 (Martini ?) dead after reset factory
I search on net and found firmware for this
http://www.mediafire.com/?1phq58wf0z0t19n
(Recommend using on Windows XP)
# INSTALL DRIVER
1. Remove battery and connect phone with PC
2. Insert battery
3. PC will detect and request for driver (follow guide in BRCM_PC_USB_Driver folder)
4. Change COM port to 4 (at this step I don't know why this device disappears quickly, so you must open device manager windows and change as quick as this device appear, but maybe this strange issue lead to bug that I will refer at the end of this)
# FLASH
1. Remove battery and connect phone with PC
2. Run download_froyo_1_3_6.bat
3. Insert battery
At the end, I saw error message as below screen, but finally it shows "Program Android New Image suceed"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
But I remove battery and insert again and power on and wait for more than 10 min. but phone only show "Join our Android"
Can anyone help?

I tried the procedures above. It is working. Actually this one is to unbrick/ firmware flash your alcatel ot-906. Although I didnt get the error message mentioned above because i think the issue was the usb driver was not installed correctly. Here is what i did:
1.download the file ot-906.rar. save and extract the file.
2.install the broadcom usb located in your extracted file named BRCM_PC_USB_Driver.
3.make sure your phone battery is charged atleast 50%, or it wont flash.
4.connect your cable to pc, not yet to phone. remove your battery, then insert it back then plug the usb. your phone should be datected by your pc as usb to serial device.
5.now open the batch file named download_froyo_1_3_6.bat.it will begin the flashing process. wait untill it says finished or success.
6.unplug the phone.remove the battery, insert again. power the phone on. now just wait 5-10 mins before you phone completely boots up.it takes sometime to boot because your phone still configures the software.
Now your phone should work fine.

not able to flash alcatel ot 906 with this method
betamax08 said:
I tried the procedures above. It is working. Actually this one is to unbrick/ firmware flash your alcatel ot-906. Although I didnt get the error message mentioned above because i think the issue was the usb driver was not installed correctly. Here is what i did:
1.download the file ot-906.rar. save and extract the file.
2.install the broadcom usb located in your extracted file named BRCM_PC_USB_Driver.
3.make sure your phone battery is charged atleast 50%, or it wont flash.
4.connect your cable to pc, not yet to phone. remove your battery, then insert it back then plug the usb. your phone should be datected by your pc as usb to serial device.
5.now open the batch file named download_froyo_1_3_6.bat.it will begin the flashing process. wait untill it says finished or success.
6.unplug the phone.remove the battery, insert again. power the phone on. now just wait 5-10 mins before you phone completely boots up.it takes sometime to boot because your phone still configures the software.
Now your phone should work fine.
Click to expand...
Click to collapse
H!!!!! i not able to flash my alcatel ot906 with this method when i try to flash com port error show i already instaled usb driver when i checked in device manger h/s not show in ports it show in disc drive so plz help me how can i solve this porblem,.......my alcatel mobile stay on only logo .........

You have to change the com port (set to com port 4). sorry i forgot to mention that step in my post. after you insert usb cable to pc, make sure you can immediately access the device manager because the comport will hide itself after 2-4 secs. to do this, you shoul open the device manager before conncting the usb cable to your pc.

Dead
My 906 dead after flash with this tutorial.
Step by step but dont turn on anymore.
If repeat the tutorial, stuck in getting image....

sharvan188 said:
H!!!!! i not able to flash my alcatel ot906 with this method when i try to flash com port error show i already instaled usb driver when i checked in device manger h/s not show in ports it show in disc drive so plz help me how can i solve this porblem,.......my alcatel mobile stay on only logo .........
Click to expand...
Click to collapse
I have the same problem, i can't succesfully install the USB driver in my windows XP, i have a code 10 error so my computer doesn't detect the request from my device (alcatel ot906Y) ... Help me please!
Thanks in advance!
PS: my phone is frozen in the logo since i install a wrong CWM, because i choose HTC H2 as model of my device and flash it. now i don't know how to do a hard reset .

i try this tutorial and now phone is dead, i can't even flash it with one touch alcatel original software updater

[Q] Nexus S USB Mount Problems [Q]

My phone can only charge but not be recognized on USB, when I plug it into my computer it says it's unrecognizable from my computer (like an error pops up). It wasn't like this before I installed the new update to the cygeonmod rom. I tried going back to stock gingerbread, other roms. Like at least 4 roms i've tried I just don't know what to do now. Any Ideas?

Are you trying to access the storage or use development tools (like adb) via USB?
Also, have you tried with a different USB port (preferably one on the motherboard of your computer)?

WindSlash said:
Are you trying to access the storage or use development tools (like adb) via USB?
Also, have you tried with a different USB port (preferably one on the motherboard of your computer)?
Click to expand...
Click to collapse
I'm just trying to access the storage, I've tried different usb ports but it just keeps saying USB Device Not Recognized.

I'm assuming you're using Windows... can you go under Device Manager and see if there is one with an exclamation mark (!) when your device is plugged in?

WindSlash said:
I'm assuming you're using Windows... can you go under Device Manager and see if there is one with an exclamation mark (!) when your device is plugged in?
Click to expand...
Click to collapse
yes theres and exclamation mark when I plug it in and it says (!) Unknown Device.

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Anyone got any solutions?

tdog1o1 said:
My phone can only charge but not be recognized on USB, when I plug it into my computer it says it's unrecognizable from my computer (like an error pops up). It wasn't like this before I installed the new update to the cygeonmod rom. I tried going back to stock gingerbread, other roms. Like at least 4 roms i've tried I just don't know what to do now. Any Ideas?
Click to expand...
Click to collapse
Had the same problem and it ended up being a faulty USB cable. Pretty unlikely, but try a different cable and see if that helps.

XK72 said:
Had the same problem and it ended up being a faulty USB cable. Pretty unlikely, but try a different cable and see if that helps.
Click to expand...
Click to collapse
I've tried different usb cables with different computers and with different usb slots in each computer. Nothing works. Is it possible that my nexus s is missing a file allowing me to connect usb to my computer? Because every computer I use it says USB DEVICE NOT RECOGNIZED so I was just wondering if that's the case.

tdog1o1 said:
I've tried different usb cables with different computers and with different usb slots in each computer. Nothing works. Is it possible that my nexus s is missing a file allowing me to connect usb to my computer? Because every computer I use it says USB DEVICE NOT RECOGNIZED so I was just wondering if that's the case.
Click to expand...
Click to collapse
It sounds like your problem can be isolated to the phone, but I'm not familiar with working in a Windows environment. I'd try booting into (the phone's) Recovery and seeing if you can mount the drive from there. Might help you isolate whether or not your issue is related to a particular volume.

XK72 said:
It sounds like your problem can be isolated to the phone, but I'm not familiar with working in a Windows environment. I'd try booting into (the phone's) Recovery and seeing if you can mount the drive from there. Might help you isolate whether or not your issue is related to a particular volume.
Click to expand...
Click to collapse
I tried that going into the phone's recovery mode and plugging in the usb cord and it still says the same thing. When I go into further like clicking the message it gives me a Code 43 warning on my computer. I also tried hard factory resetting my phone when I was on the phone with Samsung and that didn't work either. Everything was fine before I flashed Cygenmod rom on my phone everything was perfect.

tdog1o1 said:
I tried that going into the phone's recovery mode and plugging in the usb cord and it still says the same thing. When I go into further like clicking the message it gives me a Code 43 warning on my computer. I also tried hard factory resetting my phone when I was on the phone with Samsung and that didn't work either. Everything was fine before I flashed Cygenmod rom on my phone everything was perfect.
Click to expand...
Click to collapse
Have you installed the drivers from http://developer.android.com/sdk/win-usb.html?

XK72 said:
Have you installed the drivers from http://developer.android.com/sdk/win-usb.html?
Click to expand...
Click to collapse
I tried it and nothing is working.

Can you go back to Device Manager?
Double click on the "Unknown Device", then click on "Details" tab, under "Property", select "Hardware Ids", and take a screenshot of what's there?

WindSlash said:
Can you go back to Device Manager?
Double click on the "Unknown Device", then click on "Details" tab, under "Property", select "Hardware Ids", and take a screenshot of what's there?
Click to expand...
Click to collapse
Here you go.

Interesting... now let me ask you from another angle, with the phone connected and USB debugging on, are you able to access the phone using adb devices / fastboot?

download and install PDANet
worked like a charm for me, installed my usb drivers to my phone which i had problems with just like you.

WindSlash said:
Interesting... now let me ask you from another angle, with the phone connected and USB debugging on, are you able to access the phone using adb devices / fastboot?
Click to expand...
Click to collapse
No i'm not able to access it with fastboot or adb devices. All it says is USB device not recognized.

Nexus S Woes
I had the exact same story and errors as tdog1o1, and the ONLY fix I found useful was on an mp3 forum.
" I had code 43 problems with my usb ports until I found a thread on MSI's website. My front panel usb ports connected to a 9 pin usb header on the motherboard. Only 8 pins are needed. If pin 9 has a black ground wire then remove it. I didnt give this fix much hope but it fixed my problems! "
After many hours of driver installs, front usb port changes, and a dozen reboots, this actually worked!
I merely used the USB at the back of the computer and Voila!
Looks Wind Slash nailed it at the beginning of this thread.

Nexus S
I am having the exact problem, have found a solution.

Nexus 5 is not recognized as a Device, ony charges

Hi,
Three days ago, my Nexus 5 has stoped from being recognized by my computer as a device: when I plug my phone, nothing happens:
No "USB" icon/notification on my phone
No response from my PC
Enabling/disabling MTP, PTP, Debugging does not change anything
Even my
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
is not recognized anymore
I am an experienced user an it is not a driver's problem (I have already reinstalled drivers and changed USB cables). If it helps, I am on stock 4.4.4 rooted.
I don't know if anyone has ever had the same problem and can give a hint! Thanks a lot!

willylatorre said:
Hi,
Three days ago, my Nexus 5 has stoped from being recognized by my computer as a device: when I plug my phone, nothing happens:
No "USB" icon/notification on my phone
No response from my PC
Enabling/disabling MTP, PTP, Debugging does not change anything
Even my
is not recognized anymore
I am an experienced user an it is not a driver's problem (I have already reinstalled drivers and changed USB cables). If it helps, I am on stock 4.4.4 rooted.
I don't know if anyone has ever had the same problem and can give a hint! Thanks a lot!
Click to expand...
Click to collapse
Try to switch USB port in PC, reinstall your android (complete wipe of system, then reinstall it). Or maybe your windows is causing this problem.

Cable or port issue. USB port on phone, computer or cable.
Sent from my Nexus 5 using Tapatalk

Thanks, but I have already tried on multiple PCs,multiple ports and multiple cables. I don't know if it can be a sofware problem that a wipe or change of ROM can solve :/

willylatorre said:
Thanks, but I have already tried on multiple PCs,multiple ports and multiple cables. I don't know if it can be a sofware problem that a wipe or change of ROM can solve :/
Click to expand...
Click to collapse
Then perhaps USB fault on your phone.
Can't flash factory without USB
Sent from my Nexus 5 using Tapatalk

willylatorre said:
Hi,
Three days ago, my Nexus 5 has stoped from being recognized by my computer as a device: when I plug my phone, nothing happens:
No "USB" icon/notification on my phone
No response from my PC
Enabling/disabling MTP, PTP, Debugging does not change anything
Even my
is not recognized anymore
I am an experienced user an it is not a driver's problem (I have already reinstalled drivers and changed USB cables). If it helps, I am on stock 4.4.4 rooted.
I don't know if anyone has ever had the same problem and can give a hint! Thanks a lot!
Click to expand...
Click to collapse
I experienced the same issue yesterday when I tried to flash Lollipop on my Nexus5.
Using the original USB cable that came with the Nexus did the trick.

Try turning USB Debugging on Dev Options. It might help.

willylatorre said:
Hi,
Three days ago, my Nexus 5 has stoped from being recognized by my computer as a device: when I plug my phone, nothing happens:
No "USB" icon/notification on my phone
No response from my PC
Enabling/disabling MTP, PTP, Debugging does not change anything
Even my
is not recognized anymore
I am an experienced user an it is not a driver's problem (I have already reinstalled drivers and changed USB cables). If it helps, I am on stock 4.4.4 rooted.
I don't know if anyone has ever had the same problem and can give a hint! Thanks a lot!
Click to expand...
Click to collapse
you're using windows?
ither one of these two will help -
PC recognizes Nexus but then I can't access my storage
but I believe this is the one you want -
Nexus 5 connecting via USB as wrong device

Please help me to connect to pc

Am using galaxy s duos 2 (gt s7582) with stock ROM n kernal but rooted , bootloader not unlocked yet. Since 3-4 days before I got a problem that I can't connect this to any PC. When connecting only charging mode is activated. In my phone there is no USB settings accessible. So that I can't flash anything. I tried with some apps on playstore (USB settings, USB switch) ,but those r also sadly failed. When using USB settings it shows the stock USB options but no effect when changing it. What should I do . how can I solve it. Oh.. One more thing .. I tried also factory reset 2-3 times but this thing only not working. And test with 2-3 PC. But I could connect other Samsung mobiles on those PCs with same USB cable on same port successfully.. !! PLEASE HELP ME..
Sent from my GT-S7582 (Galaxy Grand Prime) using XDA-Developers mobile app

arbeenster said:
Am using galaxy s duos 2 (gt s7582) with stock ROM n kernal but rooted , bootloader not unlocked yet. Since 3-4 days before I got a problem that I can't connect this to any PC. When connecting only charging mode is activated. In my phone there is no USB settings accessible. So that I can't flash anything. I tried with some apps on playstore (USB settings, USB switch) ,but those r also sadly failed. When using USB settings it shows the stock USB options but no effect when changing it. What should I do . how can I solve it. Oh.. One more thing .. I tried also factory reset 2-3 times but this thing only not working. And test with 2-3 PC. But I could connect other Samsung mobiles on those PCs with same USB cable on same port successfully.. !! PLEASE HELP ME..
Sent from my GT-S7582 (Galaxy Grand Prime) using XDA-Developers mobile app
Click to expand...
Click to collapse
step1-install busy box app from here-https://fs07n3.sendspace.com/dl/f0bfd378acfa24606148ea74fb7e0ae5/5734c09f0fa51662/23s81l/stericson.busybox-40-APK4Fun.com.apk
step2-install mass storage enabler-http://www.apk20.com/apk/47248/start
open busybox tap on install when installation popup occurs reopen it and wail for busybox loading to 100%
connect your phone to pc and open mass storage enabler
grant root permission
click on mass storage mode
done!!!!!!!!!
but if this method isn't work with odin than contact me
.
.
.
hit thanks if i help you..:good:

Thanks in advance ,
before that i am facing one more big problem. i tried an app for easy access on recovery and safemode. i just click on boot on recovery button but now my duos 2 doesnt load android it stucks on samsung logo with a red '!' on left upper corner . even recovery cant load. i could turn on download mode but untill my usb getting normally , i think it will be useless.

charlesxd2016 said:
step1-install busy box app from here-https://fs07n3.sendspace.com/dl/f0bfd378acfa24606148ea74fb7e0ae5/5734c09f0fa51662/23s81l/stericson.busybox-40-APK4Fun.com.apk
step2-install mass storage enabler-http://www.apk20.com/apk/47248/start
open busybox tap on install when installation popup occurs reopen it and wail for busybox loading to 100%
connect your phone to pc and open mass storage enabler
grant root permission
click on mass storage mode
done!!!!!!!!!
but if this method isn't work with odin than contact me
.
.
.
hit thanks if i help you..:good:
Click to expand...
Click to collapse
but this method also didnt help me.. it showin same as previousl..
when i restart mobile while it on usb, windows detected it but showing unknown device. the usb device not recognized. its reason says "the location of the device is shown in bold type". what is that ??
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

try to use it with another pc if this not work than buy new usb cable or may be you broke your phone usb port
.
.
.
hit thanks if i help you...:good:
Sent from my GT-S7582 using XDA-Developers mobile app

charlesxd2016 said:
try to use it with another pc if this not work than buy new usb cable or may be you broke your phone usb port
.
.
.
hit thanks if i help you...:good:
Sent from my GT-S7582 using XDA-Developers mobile app
Click to expand...
Click to collapse
Oh .. ok.. then should i try with changing new usb port first..??

arbeenster said:
Oh .. ok.. then should i try with changing new usb port first..??
Click to expand...
Click to collapse
best of luck...:good:
.
.
.
hit thanks if i help you...:good: