Hi to all. I just recently rooted my alcatel one touch 906. Is there a compatible ROM for my device. Here is my device info, for reference.:
Model: alcatel one touch 906
Processor: Qualcomm msm7227
RAM: 512
Android 2.2.1
Build: fsr.1.3.6.0_t10.16
Thanks in advance. I hope you can help me..
thread updating..anyone?? thanks..
My Alcatel T906 (Martini ?) dead after reset factory
I search on net and found firmware for this
http://www.mediafire.com/?1phq58wf0z0t19n
(Recommend using on Windows XP)
# INSTALL DRIVER
1. Remove battery and connect phone with PC
2. Insert battery
3. PC will detect and request for driver (follow guide in BRCM_PC_USB_Driver folder)
4. Change COM port to 4 (at this step I don't know why this device disappears quickly, so you must open device manager windows and change as quick as this device appear, but maybe this strange issue lead to bug that I will refer at the end of this)
# FLASH
1. Remove battery and connect phone with PC
2. Run download_froyo_1_3_6.bat
3. Insert battery
At the end, I saw error message as below screen, but finally it shows "Program Android New Image suceed"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
But I remove battery and insert again and power on and wait for more than 10 min. but phone only show "Join our Android"
Can anyone help?
I tried the procedures above. It is working. Actually this one is to unbrick/ firmware flash your alcatel ot-906. Although I didnt get the error message mentioned above because i think the issue was the usb driver was not installed correctly. Here is what i did:
1.download the file ot-906.rar. save and extract the file.
2.install the broadcom usb located in your extracted file named BRCM_PC_USB_Driver.
3.make sure your phone battery is charged atleast 50%, or it wont flash.
4.connect your cable to pc, not yet to phone. remove your battery, then insert it back then plug the usb. your phone should be datected by your pc as usb to serial device.
5.now open the batch file named download_froyo_1_3_6.bat.it will begin the flashing process. wait untill it says finished or success.
6.unplug the phone.remove the battery, insert again. power the phone on. now just wait 5-10 mins before you phone completely boots up.it takes sometime to boot because your phone still configures the software.
Now your phone should work fine.
not able to flash alcatel ot 906 with this method
betamax08 said:
I tried the procedures above. It is working. Actually this one is to unbrick/ firmware flash your alcatel ot-906. Although I didnt get the error message mentioned above because i think the issue was the usb driver was not installed correctly. Here is what i did:
1.download the file ot-906.rar. save and extract the file.
2.install the broadcom usb located in your extracted file named BRCM_PC_USB_Driver.
3.make sure your phone battery is charged atleast 50%, or it wont flash.
4.connect your cable to pc, not yet to phone. remove your battery, then insert it back then plug the usb. your phone should be datected by your pc as usb to serial device.
5.now open the batch file named download_froyo_1_3_6.bat.it will begin the flashing process. wait untill it says finished or success.
6.unplug the phone.remove the battery, insert again. power the phone on. now just wait 5-10 mins before you phone completely boots up.it takes sometime to boot because your phone still configures the software.
Now your phone should work fine.
Click to expand...
Click to collapse
H!!!!! i not able to flash my alcatel ot906 with this method when i try to flash com port error show i already instaled usb driver when i checked in device manger h/s not show in ports it show in disc drive so plz help me how can i solve this porblem,.......my alcatel mobile stay on only logo .........
You have to change the com port (set to com port 4). sorry i forgot to mention that step in my post. after you insert usb cable to pc, make sure you can immediately access the device manager because the comport will hide itself after 2-4 secs. to do this, you shoul open the device manager before conncting the usb cable to your pc.
Dead
My 906 dead after flash with this tutorial.
Step by step but dont turn on anymore.
If repeat the tutorial, stuck in getting image....
sharvan188 said:
H!!!!! i not able to flash my alcatel ot906 with this method when i try to flash com port error show i already instaled usb driver when i checked in device manger h/s not show in ports it show in disc drive so plz help me how can i solve this porblem,.......my alcatel mobile stay on only logo .........
Click to expand...
Click to collapse
I have the same problem, i can't succesfully install the USB driver in my windows XP, i have a code 10 error so my computer doesn't detect the request from my device (alcatel ot906Y) ... Help me please!
Thanks in advance!
PS: my phone is frozen in the logo since i install a wrong CWM, because i choose HTC H2 as model of my device and flash it. now i don't know how to do a hard reset .
i try this tutorial and now phone is dead, i can't even flash it with one touch alcatel original software updater
Related
i m not responcible for any damages
do at your own risk
read all twice before flashing
til date i have flashed more then 10 times by this method
Make sure that you read everything carefully and know what you are doing.
Don't blame me for any damage that may occur on your phone.
-----------------------------------------------------------------------------------------
-do not disconnect mobile while flashing bettery must be more then 50%
-pc/laptop must not stop while flashing
-close other progames running in your pc/laptop for better speed-discoonect net
-images given here for learning purpose for better understanding of all steps
-you can practice till step 3 before all steps
-there is tutorial inside downloaded file by micromax do not use it(stictly -they given image for firmware upgread and you have to click download button)
---------------------------------------------------------------------------
What's needed:
1)USB data cable
its there with your chrgere right!!!
2)MediaTek USB VCOM drivers
-go to settings-developer option - click on usb debuging mode ok
-now connect your mobile with your pc/laptop and driver containg drive created open it and install your desire 32 bit or 64 bit driver(run as admin)
---restart your pc with phone connected
---to check is your driver instal or not go to usb teether option and apply it. if internet surfing is possible then you are ready to go---(must check)
3)SP Flash Tool and flashing files
-- is provided with in download file
-- 2 rar files
----make new folder and extract both files in new folder
--so threre is two folder one for sp flash tool and one containing all flashing files (warning =do not rename this folder)
--------------------------------------------------------------------------------------------------------------------
1)open spflsh tool
First of all open SP Flash Tool, then click Scatter-loading button to load the correct scatter file
(here it is named MT6577_Android_scatter_emmc.txtfind in download file)
all files will be loded
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2)choose Option-USB Model,click USB Model,
Choose Option- DownLoad All-Speed-High speed click High Speed
3)now connect your fone with micro usb data cable (do not connect to pc now just only fone side connect)
Turn off your phone, remove the battery and replace it after some seconds (and don't turn on the phone).
now fone is turn off with data cable coonect with fone side only
4) now do some speedy work
press download and connect immediatly to pc (same usb port when you use while instaling the driver)
The process will start and a red progress bar will appear.
After the red progress bar is complete(for 1 sec)
there will appear a purple progress bar(for1 sec
.
and thene yellow bar(for1 min to 5 min)
When the yellow bar is complete, you'll get a popup with a green circle and Download OK message, which means that the process has been successfully terminated.
5)You can now safely disconnect your phone and turn it on. The process ends here
remove your mobile and start it will take 2 min to first boot
enjoy!!!!!!!!
-----------------------------------------------
download links
---------------------------------
what's new in updated stock v2:
Auto rotation sensor bit improved
- internal memory now increased to 1.58 ,rest is internal card 1.12 gb
- now u can install apps in external memory card default.
battery improve.
true colour.
GPS fix.
better performance.
now install pass on memory card.
and lots more finding.
updated smooth scrolling.
--------------------------------
in downloaded file you will get sp flash tool and flashing files
make new folder and extract all 2 rar files in new folder
----------------------------------
stock rom version 2 links resume
stock rom version 2 mirror links resume
--------------------------------
reserved
i have flashed many times and found no need to remove battery just make sure all drivers are installed in pc even in mobile off mode also. then when u click upgrade firmware simply switch off ur mobile u feel the vibration after 5 sec of switch then simply connect it to usb cable thats all.
Error on Sp tool
I am getting this error I dont know what to do please help.
Please refer to the screen shot
deadmantfa said:
I am getting this error I dont know what to do please help.
Please refer to the screen shot
Click to expand...
Click to collapse
drivers not installed properly. install them again.
deadmantfa said:
I am getting this error I dont know what to do please help.
Please refer to the screen shot
Click to expand...
Click to collapse
Your vcom drivers not installed properly.....
Sent from my Micromax A110 using xda premium
mmx a110
Dibbyo123 said:
Your vcom drivers not installed properly.....
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
dead on sp tool error 4010 after red line no preloader driver plzz help me
Let's take everything over to this thread: http://forum.xda-developers.com/showthread.php?t=2167244
The guide is for the Alcatel OT-918 (No D, N, MIX), single sim, Orange Pasadena, from Romania with Gingerbread 2.3.6, it might work on other versions to, but I can't guarantee that.
Care should be taken, while the Orange Pasadena is a cheap phone, modifying your software might turn your device in an unusable brick.
Unfortunately the Android version of this phone can't be rooted with superoneclick or other simpler methods.
First of all You need the following tools from the attached file:
USB Drivers
SP_Flash_Tool_v3.1224.00
AlcatelScatterRetriever01 - optional
Universal recovery for Alcatel OT918 (2.3.5 and 2.3.6)
Superuser-3.0.7-efghi-signed.zip
http://dl.dropbox.com/u/74256292/Pasadena/Orange_Pasadena_OT918_root.zip
1. Turn off the phone, and connect it to the computer (Windows XP/7) with an USB cable, and install the attached drivers
2. Create a scatter file with AlcatelScatterRetriever01,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(alternatively you can skip this step and use the scatter file from the OT-918_Orange_Pasadena_Branded folder)
3. Run Flash tool and open the scatter file
4. Check only the recovery file from the OT-918_Orange_Pasadena_Branded folder
Double check that all other checkboxes must be unchecked!
5. Click on download
6. Connect the turned off phone to the computer, the progress bar should change its color and after a short while a small window with a green circle and ok should appear.
If it's not working remove USB cable, the battery, and reconnect the battery and then the USB cable and try again.
7. Remove the battery and the SD-card
8. Copy Superuser-3.0.7-efghi-signed.zip to the SD-card
9. Replace the SD-card and the battery
10. Start the phone with the Volume UP and Power combo (release first the power button)
11. You should be in the OT-918N recovery, and should install the file Superuser-3.0.7-efghi-signed.zip from the SD-card
12. Restart and enjoy your root-ed phone.
For UNROOT make a full wipe from recovery.
Repair information:
If you got an Orange Pasadena which would not boot or is in a bootloop, at step 4 select all the files from OT-918_Orange_Pasadena_Branded folder and go on with the guide.
At step 8 copy to the SD-card deepROM 2.3.6. from http://4pda.ru/forum/index.php?showtopic=323769&st=2320#entry16968462 ,
the file from http://disk.yandex.com/public/?hash=%2BFgTiMPQgqQjcFeH30tIoZnLBEVANGQz3%2BeBBWub5m0%3D ,
which is the only functional custom rom as far as I know for this model of the phone.
If someone needs a functional (but incomplete) stock image feel free to p.m. me.
Still searching for a full stock image, which will be posted here.
Thanks to qwe-, Linerty, elpopa, jman0, deep4512, breakk, @zoyB, cappa72, and all other who contributed to this guide.
Drivers
Hello,
At step "1: Turn off the phone, and connect it to the computer (Windows XP/7) with an USB cable, and install the attached drivers"
Witch one of the drivers should I install? I've tried everything, but the phone it is not recognized by the XP OS, and therefore the ASR.exe cannot generate the scattering file.
Please help, with more detailed procedure regarding the drivers.
Thank you,
Stro
It works, thank you!
Is there anyway to install another, more stable, Rom.
Maybe an original OT-918 ROM?
Thanks.
guys, i'm trying to reinstall an ot-918 device, with luck, but now the sim doesn't work (I have an network issue). what can I do?
also I've tried to follow this tutorial to add the IMEI back ('cause now is null), but without any luck (I don't have any "write imei" button). can someone help me out please?
How to Root iBerry Auxus Linea L1
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I Have Found Many Users Searching For Root For Auxus Linea Li Root
Today I am going to provide you the process for rooting the phone. After rooting you can do a lot more in it. You can install custom ROMs, you can update the phone firmware, you can remove pre-installed application from the same, etc. Adding custom rom is the best thing you can do on it. So let’s move ahead with rooting. Remember that it is a one way proceed. That means once rooted you won’t restore things back. Also you will lose the phone warranty.
Requirements:
Rooting means simply messing with phone permission. Sometime if you go with wrong stuff your phone will brick or wont boot. At that point resorting factory settings will only work. It is good if you can backup your phone first. And then only went ahead with the process.
Charge the device to maximum. Never attempt to root or make any changes if the battery is low. This can cause serious issue.
You have to update your system with latest usb drivers that will help your windows pc to communicate with the mobile phone. Install that.
Go in the settings and tap on developer options. There you can find usb debugging. Turn that thing on.
Download SP FLASH TOOL and keep it in a folder on your desktop.
Download the original iBerry Auxus Linea L1 USB Drivers and install them.
Download the Boot Recovery & Scatter files for iBerry Auxus Linea L1.
The last thing you will need is MTK Droid Root 2.5.3 root tool.
Rooting Process:
1.Extract the content of Sp Flash zip file in a folder. There will be a flash tool.
2.Extract the content of boot recovery and scatter in the same folder.
3.Run the sp flash took in the admin mode. In that you have to click on scatter loading. Choose the scatter file. This file will be available in the boot recovery folder.
4.The next thing you have to do is select the boot image file. You can do that by clicking on the left side of the Flash Tool.(just Click check box & click in blank space next to bootimg. and select Linea-L1_140626__boot_patched_140719-173447.img only)
5.Once done just check once again that the files are properly selected.
6.Now you have to extract the content of drivers that you had downloaded. Switch off your phone and connect it to your pc. Your pc will ask for the drivers. You have to provide the folder location.
7.When you are done with driver installation disconnect the phone and remove the phone battery.
8.Connect the phone just like that in switch off mode. After few seconds insert the battery back and then connect the phone to pc. Now in sp flash tool click on the download button.(FOR DRIVER HELP http://http://forum.xda-developers.com/showthread.php?t=2180436)
9.Flashing will start and you will get a completed process at the end.
10.After that you have to run the droid root software. For that first turn on your phone and from settings enable usb debugging. If you are unable to find the same then go in about and tap on build 5 times to turn on developer options.
Just connect the phone and then going Droid Root software. There you can find Backup recovery tab. Click on that and then click on super su. This will install super su user on the phone. You can then update the app from Google Play store.
U can ask a question if any of my wording is not understandable.
SP Flash Tool 3.1352.01 (5.1352.01).rar
Thanks
Nice :good: but is there any OS mod available? Looking forward for that
charancherry said:
Nice :good: but is there any OS mod available? Looking forward for that
Click to expand...
Click to collapse
May b in some days .
Hi Bro,
Nice to see this, But when i am doing... After clicking the download button nothing is happening. One full night i kept with connected. nothing is working fine...
Kindly help me....
Thanks & Regards
prasadskht said:
Hi Bro,
Nice to see this, But when i am doing... After clicking the download button nothing is happening. One full night i kept with connected. nothing is working fine...
Kindly help me....
Thanks & Regards
Click to expand...
Click to collapse
Switch off your phone and connect it to your pc. Your pc will ask for the drivers. You have to provide the folder location.Install Driver First And follow the procedure above mention .
manish dubey said:
Switch off your phone and connect it to your pc. Your pc will ask for the drivers. You have to provide the folder location.Install Driver First And follow the procedure above mention .
Click to expand...
Click to collapse
Thanks Bro,
Now i am able to do flash and followed the same steps. After i installed "Titanium back" when i tried to open it saying "Sorry, I could not acquire root privileges............................."
Kindly help me ...
Cutom rom for my Auxus linea L1
i am not getting any custom rom for this phone any side
are you working anything for this
i will be waiting for your reply
Yes I am waiting for any dev to make custom recovery for it ..
Hello everyone,
My S700 can't be powered on and it will not charge :crying: i think SP can detected my S700 yet but the device manager loop between "MediaTek USB port (COM14)" and "MediaTek Preloader USB VCOM (Android) (COM12)"... and me i'm crying !!! PLEASE HELP ME whta i will do ???
I understand that my last solution is to flash yet from the manufactor ROM... so to lost my work :'( but before i need to be sure that this troubles about my port COM 12 and 14 will make not more troubles ???
I hope you will understand better my troubles from this details :
*1/ I download the new S700 ROM from the manufactor website so i installed the drivers and flash it whith SP_MDT_exe_v3.1504-A2015.03.18-v06-customer => success! The 20150624_c218v13_jbl_a228_hd_3m_mstar ROM working well and during 2 weeks i install all my applications, contacts, ...
*2/ I try to transfer my sms from my old phone (Iocean X7hd) to my new S700 with Helium. It recognize my X7 and save my sms but it not working with the S700 (i opened a ticket to Helium) so i installed ALL MTK+ADB drivers found in this file www.adrive.com/public/fSxNQP/All MTK USB Driverv.9.2.PDanet.Adb 2015.zip => never working ! I remember about a conflict driver message...
*3/ I use MOBILedit ENTERPRISE_7_8_3_6076 to make a backup => it recognize my S700 and make a partial backup because my S700 is not rooted
*4/ I download the files from www.needrom.com/download/mstar-s700 about to root for version 20150624_c218v13_jbl_a228_hd_3m_mstar uploaded by fpiva4a : https://drive.google.com/file/d/0B358CZ0vWBWpcWZfV3A4bDFEaTg/view
*5/ I follow the tuto from forum.xda-developers.com/android/general/mstar-s700-review-5-5-hd-touch-id-t3132431/page3 so i open SPFT v5.1528, choose the download agent+scatter file from the fpiva4a's files :
- On the main screen choose firmware upgrade from the drop down menu
- Pull out the battery and connect your phone to your PC, let the SPFT and the phone initiate a 'handshake' => there is nothing (i don't remeber if at this step the device manager loop already...)
- Unplug your phone from the USB cable. Click on the download button on the main screen. Now put your battery back into the phone and plug in the phone to your pc using the usb cable=> the SP Flah Tool start and see a progress bar but i have this error :
" BROM ERROR : S_FTHND_FILE_IS_NOT_LOADED_YET (5007)
There is file not loaded yet!!
[HINT]:
1. Please check if the DA path is correct.
2. Please check if all the ROM files exist.
3. Please check if the scatter file description is sync with the exist ROM files"
*6/ I click on help+ok, close SP and unplugg my S700 => i can't be powered on !!!
*7/ I plug the USB cable and i heard sound to mount it and after loop to unmount => i thought about a conflict (step */2) so from the device manager i try to unistall the "MediaTek USB port" and "MediaTek Preloader USB VCOM (Android)" what loop. Also i uninstall from the Control Panel W7 all the drivers installed by step */2
*8/ I try several times the *5/ but always like */6 my S700 not power on
*9/ I use USBdeview and try to uninstall my port => the green line always loop between this 2 lines
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and i open the SP_MDT_exe_v3.1504-A2015.03.18-v06-customer from step *1/ => the scan is well and find my S700 on the port COM12
thanks for your help and sorry for this big post but i wanted to follow all the details even if i read all your link i don't find a specific reply about my trouble
Fail test
Several helpers said me to resolve my mistake when i want to try new recovery+root to reflash with the manufactor ROM. So i come back to the step 1, I download the new S700 ROM from the factory website and flash it with SP Flash tool => by SP__MDT_exe_v3.1504-A2015.03.18-v06 or SPFT v5.1528 it was same : success DL but my S700 doesn't restart.... :'(
Instead of firmware upgrade i test also Format All+Download but my S700 doesn't restart :'( So now i don't know what i can do ??? pleassse
pee_why said:
Several helpers said me to resolve my mistake when i want to try new recovery+root to reflash with the manufactor ROM. So i come back to the step 1, I download the new S700 ROM from the factory website and flash it with SP Flash tool => by SP__MDT_exe_v3.1504-A2015.03.18-v06 or SPFT v5.1528 it was same : success DL but my S700 doesn't restart.... :'(
Instead of firmware upgrade i test also Format All+Download but my S700 doesn't restart :'( So now i don't know what i can do ??? pleassse
Click to expand...
Click to collapse
Hi, thanks for using XDA Assist!
Please ask for further assistance here:
http://forum.xda-developers.com/general/help
You'll find expert advice there.
Good luck!
Thread closed.
Hi
I'm having a problem with my Acer Liquid E3 Duo (E380); after unlocking my 2 SIM cards and having successfully unlocked my phone I'm getting error messages saying that application xxx stopped working. The only thing I can do is acknowledged the message and then next error for the next application is appearing.
I've no clue if it can be repaired; I tried the recovery mode but without success.
I tried to flash the original ROM (downloaded from ACER) but I've issues.
I will try to explain what I've done.
OS used Windows 10
I downloaded the original KiKat zip (ROM) file from Acer
I downloaded / installed the VCOM drivers
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I downloaded SP Flash Tool v5.1628.00
I powered off the phone (cannot remove the battery)
Connected the phone with USB cable
Started SP Flash Tool
Selected the original scatter file which was provided by Acer (zip)
Click on Download
Got error 8417
Found another scatter file MT6589_Android_scatter_emmc; I copied it in the same directory that the original
Tried again to open the scatter and it worked (was loaded)
Is it normal that 'only' BOOTIMG is selected ???
Plugged the USB cable with a power-off phone
Click on download; nothing happened
Remove USB cable; re-inserted the USB cable download went to 100%
and finally got the error >> PMT Changed for the ROM; it must be downloaded <<<
I formatted the phone successfully; re-downloaded the ROM and got the same PMT error message
Surprisingly the phone is still working as it was prior all my attempts. So no real damage but as stated it is unusable due to all apps crashing.
Thanks in advance for your support
Me063 said:
Hi
I'm having a problem with my Acer Liquid E3 Duo (E380); after unlocking my 2 SIM cards and having successfully unlocked my phone I'm getting error messages saying that application xxx stopped working. The only thing I can do is acknowledged the message and then next error for the next application is appearing.
I've no clue if it can be repaired; I tried the recovery mode but without success.
I tried to flash the original ROM (downloaded from ACER) but I've issues.
I will try to explain what I've done.
OS used Windows 10
I downloaded the original KiKat zip (ROM) file from Acer
I downloaded / installed the VCOM drivers
I downloaded SP Flash Tool v5.1628.00
I powered off the phone (cannot remove the battery)
Connected the phone with USB cable
Started SP Flash Tool
Selected the original scatter file which was provided by Acer (zip)
Click on Download
Got error 8417
Found another scatter file MT6589_Android_scatter_emmc; I copied it in the same directory that the original
Tried again to open the scatter and it worked (was loaded)
Is it normal that 'only' BOOTIMG is selected ???
Plugged the USB cable with a power-off phone
Click on download; nothing happened
Remove USB cable; re-inserted the USB cable download went to 100%
and finally got the error >> PMT Changed for the ROM; it must be downloaded <<<
I formatted the phone successfully; re-downloaded the ROM and got the same PMT error message
Surprisingly the phone is still working as it was prior all my attempts. So no real damage but as stated it is unusable due to all apps crashing.
Thanks in advance for your support
Click to expand...
Click to collapse
Greetings and welcome to xda. I'm not familiar with your device but I have found this thread here
http://forum.xda-developers.com/showthread.php?t=2711667
That has firmware you can try and lots of useful information. Hopefully the experts there can help you better
Good Luck
Sawdoctor