Hello
after installing magldr 1.12 (wanted to try win7) my htc hd2 is stuck on white screen with htc logo. I saw simmilar posts how to solve this problem but holding down volume key and pressing turn on button doesnt boot into four colour screen it is still white screen with green logo
1.66 rom eastern europe was installed and 2.08hspl, however I didnt install any radio How to get back to rom
Thank you in advance
any solution to this problem?? i am having same issue. thnx
Can you post step-by-step what you did?
Did You make task29 before magldr?
White screen after magldr 112 - help !
titjukaz said:
hello
after installing magldr 1.12 (wanted to try win7) my htc hd2 is stuck on white screen with htc logo. I saw simmilar posts how to solve this problem but holding down volume key and pressing turn on button doesnt boot into four colour screen it is still white screen with green logo
1.66 rom eastern europe was installed and 2.08hspl, however i didnt install any radio how to get back to rom
thank you in advance
Click to expand...
Click to collapse
hello
i have the same problem !
have you found the solution ?
Please , answer me ....
Thanks
alessanro - venice - italy
same problem here please help
After flashing Magldr the Phone Reboots but gets stuck at the Splash Screen
You most probably have an older incompatable Radio on your phone. The Radio needs to be at LEAST 2.08.50 and the .50 is very important as it means the Radio is 576 RAM compatable (as stated in post1). The Radio I recommend is 2.15.50.14 and you can download it *HERE*. Boot your phone into the Bootloader Screen and flash a newer Radio and everything should be fine
White screen of death
I have the same problem.
Installed:
* HardSPL 3.00
* Radio 2.15.50.14
* MAGLDR 1.13 - here I got the same problem as all in this thread: white screen with HTC logo after reboot hanging forever. MAGLDR doesn't load by switching off, pressing and holding volume down and power buttons.
Any solution to this?
Wow! Got MAGLDR installed finally… after several cycles of different installations.
Here is what I found:
My original SPL was 3.00-0000, so previously I tried installing 3.00-HSPL. That didn’t work.
Now I installed exactly 2.08-HSPL version and here we go – I see MAGLDR menu now!
Good luck everyone! I hope this will help others with the same problem. I think we all need to read carefully (about 2.08) )))
Related
Hi,
By mistake I put a custom ROM for KJAM on my S200...This ROM is used before u start unlocking CID. The ROM went ok in the setup, and then it reset the device.
After that I could not even see anything, as the screen was black, with some white light flashing...& and the power, bluetooth LEDs kept flashing with black screen.
I tried to get into the bootloader mode, but no way...it gives the same black screen with blinking LEDs....
Please Help
I have a Qtek S200 and have been using the Prophet_Orange_UK_Rom. I decided this morning to revery back to my initial upgrade PDAMobiz_Prophet_WM6_V1.00 Rom. However in the middle of the update process in step 2, something happened which caused the update to fail.
No my qtek starts and gets stuck on the boot screen where you see the orange logo and IPL, SPL etc... info. When I plug the usb cable, there's no message from my computer (and no ack from activesync) but the power led shows it's charging. Any ideas as to what I can do? I've tried hardware reset several times and after saying Format is completed!, I end up with the same stuck-up boot screen.
Thanks for your big help!
done it
sorry for the bother. Was doing hardware reset with both cam and comm buttons pressed. Did not know about boot reset with comm button only...
hi, may i know what you did after you went to bootloader?
my dopod 818pro just struck at the three color screen.
pls help.
I read Wiki, reflashed ROM. Now ok.
I need help. I have a wizzard/vario. Recently installed TNT Profesional + htc home rom on it. Its worked fine for over a week. Suddenly it switched itself off, and now its stuck on the "Windows mobile 6 pro" boot screen. its ipl is 2.21.001 erm its got the whole flashing light to show its active, when i press a button, they all iluminate, it just doesnt leave the boot screen tho. Desperate for help and will try anything! Thanks...
Hello again,
I been flashing ROMS for a while now but now I having some problems that I can't solve.
Since I installed the Laurentius26_KaiserDiamond_V10 I can't update the rom anymore. The Kaiser connects to the update, the update program confirms the connection (it checks if the battery is above 50%, confirm the previous fiirmware, etc.)
When the program shows the progress bar (On the PC) the kaiser screen blimp one time to the grey screen (the one with the progression bar) and turn back to three collors screen (in less than a second). After one or two minutes the program (on the PC) gives a erro message.
I have to reset the Kaiser but no ROM was installed
Does anyone know how to solve this problem? I'm using SPL 3.29 but I have already tried Hard SPL 3.28 and back to the 3.29 again.
Thanks
Hi there,
That happened to me too. What I had to do was to download the original rom from HTC and flash that. After, i did the usual: hard reset, remove batter, restart computer. Then I could flash
Michael
Diamond: dutty 1.8 full
Kaiser: Romeos 4.3
Check the link in My Sig.
Ta
Dave
I tried your sugestions. Tried to flash the original Orange ROM but had the same problem as the cooked ROMs. It stopped at the three colors screen.
I think myh problem is a little different from other cases here. My phone is working with the Rom it have right now. It only got stuck on the three color screen when trying to flash a new Rom. To remove the screen is just reset it (normal reset, no hard reset) and it goes back to 'normal' but with the old rom. Can't flash a new one
Also tried the mtty.exe method, but when I open the mtty it shows "CLIENT". If I push any key it shows one more "CLIENTE". after 34 "CLIENT" Messages (it shows "CLIENTCLIENTCLIENTCLIENT" it freezes...
Can someone help me please?
Thanks
Try flashing the new Hard SPL be cmonex.
http://forum.xda-developers.com/showthread.php?t=420683
Thanks
Dave
Hi everybody!
Been searching for this problem on google and on this forum, but i can't find an answer to this
It's like this that i've installed wm 6.5 on my prophet, everthing was fine!
The problem was when i was trying to install another keyboard layout it restarted, and then it got stuck at the "splash screen" with the Qtek logo.
I did an Hard SPL, nothing happened.
After that i tried to boot into bootloader, everything was fine, i saw the three color screen and i started to install a new clean copy of the WM 6.5..
Everything was fine, it went to 100%, but when it was at 100% the device shutdowns.
When i tried to start it again i got into the three color screen again, and after about 7 seconds it restarts, and it starts in the three color screen...
Please help me..
Please... I really want my phone to get back to normal...?
try to connect the USB and run WM5 Rom.
The same problem..
I have the same problem after try to flash rom to my 818pro.It's still reboot into 3-color screen.How can I do??
Try flash this rom: RUU_Prophet_220734_2207114_024721_NVID.exe
from: http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
Michal