I have a Samsung Vibrant and this is exactly what happened. Please help me turn my phone back on.
Android System Recovery <3e> after using Odin3 v1.00
All:
I used Odin3 v100 to load Android 2.2 ROM
I followed the following steps
i9000XXJP2 Instructions
1. Remove the battery from your phone
2. Remove the SIM Card and MicroSD Card from your phone
3. Place the battery back on the phone
4. Hold down the HOME button, Volume Down button, and Power On button
5. You should now see a Download screen
6. Open Odin 3 v1.0
7. Click on the button “PIT” and load the “s1_odin_20100512.pit” file
8. Click on the button “PDA” and load the “I9000XXJP2-REV03-PDA-CL464213.tar” inside of the firmware download’s .rar file.
9. Click on the button “Phone” and load the “MODEM_I9000XXJP2.tar” inside of the firmware download’s .rar file.
10. Click on the button “CSC” and load the “GT-I9000-CSC-MULTI-OXAJP2.tar” inside of the firmware download’s .rar file.
11. Click the checkbox next to: “Re-Partition”
12. Your settings should now look like Figure #2
13. Plug your phone into your computer with USB Debugging on
14. Look at the gallery below to see if everything is going right
15. Once done, your phone will boot up
And now the phone Rebooted and I get the following message “update media, plase waite E:Cant mount /dev/block/mmcblk0p1 (invaild argument) E: copy_dbdata_media:Can't mount SDCARD: you storage not prepared yet. plase use UI menu for format and reboot actions. copy default media contenr failed.”
I have tried in vain to boot in the “Download Mode” to try and re flash the device and no luck.
I have tried using the following commands in SDK “C:\android-sdk_r06-windows\android-sdk-windows\tools\adb reboot-bootloader” and no luck
Am I hosed?
It seems to me that I need to reformat the internal SD Card but I cannot select any of the options in the Android System Recovery <3e>
The options I have are
Enter: OK Key, Select : Vol UP /Vol Down
Reboot system now
Applysdcard:update.zip
Wipe date/factory reset
Wipe cache partition
Format internal sd-card
The Volume rocket works to move between the above options but I can use the “OK” key nor any other to select an action
Any help is much appreciated, Thanks in advance.
help me..when i try to install sd rom (MCCM DS V4.0).when i perform the following steps after extracting the rom
Boot with MAGDLR:
1- copy folder (Android) to SD Card .
2- Boot in MAGDLR powering on your phone while you press the power button until MAGDLR appears.
3- Select "SERVICES"
4- Select "BOOT SETTINGS"
5- Select "AD SD Dir"
6- Select the "ANDROID" folder or the folder where you dropped the rom.
7- Now select "BOOT AD SD" and wait boot .....
i receive load zImage and SD kernel open failed message in red. what do i have to do..am i missing something like latest kernel..? plz help me.. the folder does contain a file zImage
CWM 5.0.2.8
Instructions
A. To enter the recovery, you need to disable the device to clamp down "on" and press "Volume -".
Two. In order to mix between the elements in recovery need to use the "Volume -" and "Volume".
Three. To select a menu item, use the "House" (In the previous menu selection was carried out rekaveri button "on", so now this button is not working and when you click on it will be a blank screen with the logo of CWM (if you accidentally clicked on, then return in the normal state can press the button one more time "on" button or menu).
4. To go back to paragraph (meaning back), you should use the "Back"
Five. Like everything, if anyone has found the comments about the instructions, you can write to me about it in the LS
Installation manual
A. Unzip the downloaded archive
Two. Go to the folder "ClockWorkMod v5.0.2.8 by RusTorg and SaNek011"
Three. Run the file "install.bat"
4. Connect the phone mode or in "DFU" (http://4pda.ru/forum/index.php?s=&showtopic=300717&view=findpost&p=13072356) or "FTM" (need androyd off above 2.1!)
Five. Follow the instructions in the program
6. After installation, you will automatically fall into recovery on this installation is finished
Setting the phone
A. Download the archive.
Two. Remove from the archive file "CMW-5.0.2.8-v9.img".
Three. Put the SD and rename the "recovery.img".
4. In a terminal enter
su
flash_image recovery / sdcard / recovery.img.
Five. In this set rekaveri: happy:!
---------------------------------------
http://translate.google.com
DOWNLOAD
Cautions:
1.your warranty is now void.
2.do this at your own risk.
3.read the whole post before starting.
Flashing CWM recovery and taking backup :
1. Download the package and extract all files.
2. Extract the driver.zip located in drivers folder->1
3. Install the driver.if your OS is 64bit then install the x64 one.if the OS is 32bit,then the x86 one.
4. Open researchdownload application
5. Select the 2nd button with double cog sign.
6. Now a new window will appear like the screenshot attached.
7. Right click on the file name field.choose the files located in "Required files" folder of the package.
be careful here.Put fdl1 in fdl1 field,fdl2 in 2nd field and the recovery image(extract the "CWM-recovery-SC8810-nonpadded.zip") in recovery field. Then press the "OK" button.
8. Press the Start (Play) button in ResearchDownload -application (third button).
9. Turn off the phone.
10. Keep holding the "- volume" key. Without releasing the button "- volume" plug the usb cable
11. The process of CWM- burning should be started now in ResearchDownload-application and it will take approximately 1 Minute.
I think you can release the Vol.Button, but I had kept it nevertheless.
12. Wait until the CWM-flashing has been finished (A green sign will appeare and "Passed" will be shown in ResearchDownload- application window).
13. Remove the battery, wait 20 seconds. Put battery back and turn on the phone.
14. now hold the vol (-) and power button until the screen flashes (40 seconds or less or more) and now you are in the CWM recovery menu.
15. PLEASE make a full backup by the "backup and restore" option .make sure there's about 500mb free space in your micro SD card.
16. after the backup reboot the phone and PLEASE store the backup files in somewhere else..(the whole ''clockworkmod'' folder)
congratulation. you have done a full backup and flashed your CWM recovery.
Rooting device:
*don't do this.if u find that your backup size is lower than 250mb~300mb(slight +/- may occur)
1. download and put the "superuserandfullbackup.zip" in your micro SD card
2. power off your device.
2. Reboot to Recovery by holding volume (-) and power button until the screen flashes and recovery menu comes.
3. just go to "install zip from sdcard option and select the zip "superuserandfullbackup.zip"
4. flash it
5. reboot.
Advices:
Rooting is dangerous.so first make a full backup of your unrooted stock Rom just after flashing CWM.
Store the backup(size will be around 250mb~300mb(+/- ) in someplace safe.it's the life of your phone.If anything goes wrong,it's the only key to fix your phone.......be careful.........
Getting back your warranty:
Restore your stock Rom's backup.Then,flash the stock recovery(included in the package.find it in RECOVERIES folder),in the same way you've flashed the CWM.
good luck.and thanks for reading this.
Hi everyone,I have been in possession of an Alcatel One Touch Pop S3 5050 for quite a long time and was not able to root it until recently.
I will share my method in this topic but first of all, I have to thanks Decker.Kaluga for developing a custom CWM recovery image that kind of work on this device. You can find a good tutorial on how to install CWM on OT-6036Y or OT-6050Y on his website.
My second thanks goes to morgs640 for the idea of adapting Decker's work on Alcatel Pop S3.
This method may work with other Alcatel devices, see last question in the FAQ section for more informations.
This method should not arm your device but as any root operation, there is always a risk. I am not responsible if anything goes wrong.
Click to expand...
Click to collapse
Step One
- Download Decker's custom CWM recovery here: cwm_alcatel_6050y.7z
- Unzip it
- Install adb drivers
Step Two
- Download latest zip version of Supersu from Chainfire, currently the 2.46
- Rename the archive as update.zip
- Put this file in the CWM recovery folder
Step Three
- Connect the device in USB, activate debug option and make sure adb is working by going to the folder where you have unziped the custom recovery
Code:
adb devices
- Navigate inside the device memory to identify the location of the internal and external memory:
Code:
adb shell ls /storage/
For internal memory, it should be:
Code:
/storage/sdcard0
And for external memory (sdcard):
Code:
/storage/sdcard1
- Push the Supersu zip file to external memory
Code:
adb push update.zip /storage/sdcard1/
- Take note of the position of the update.zip file inside the external memory
Code:
adb shell ls /storage/sdcard1/
In my case, this command returns:
Code:
- Android
- DCIM
- Documents
- Download
- LOST.DIR
- Pictures
- Ringtones
- data
- media
- update.zip
My update.zip file is in 10th position.
Step Four
- Reboot the device in fasboot by pressing Volume Down and Power until logo Alcatel pop S3 appears
- Verify the device is connected:
Code:
fastboot -i 0x1bbb devices
Boot the device with the custom recovery:
Code:
fastboot -i 0x1bbb boot cwm_recovery_6050y.img
NOTE: This does not install the custom recovery on the phone so pressing Power during 5 seconds will reboot the phone normally.
The screen will turn white, wait until it stabilizes.
The screen will remain white as the recovery is not specially developed for this device but it should work anyway.
Step Five
This is the tricky part, the menu does not display but the recovery is running anyway.
The menu you are not seeing is the following:
Code:
> reboot system now
> install zip
> wipe data/factory reset
> wipe cache partition
> backup and restore
> mounts and storage
> advanced
By default the cursor is on the first option.
- Press Volume Down once then Power to enter the install zip option.
This menu will be opened:
Code:
> choose zip from /sdcard
> choose zip from /storage/sdcard1
> choose zip from last install folder
> install zip from sideload
> toggle signature verification
+++++Go Back+++++
- Press Volume Down once then Power to enter the choose zip from /storage/sdcard1 option.
This will open the external memory folder:
In my case:
Code:
Android
DCIM
Documents
Download
LOST.DIR
Pictures
Ringtones
data
media
update.zip
- As you know exactly the position of the update.zip file from Step Three, press Volume Down accordingly.
In my case, 9 times to go from Android folder to update.zip- Then press Power
It will prompt for a confirmation:
Code:
> No
> Yes - install update.zip
- Press Volume Down once then Power to install.
- Finally, Press Power one more time to confirm installation, then reboot manually the device by pressing Power during 5 seconds.
If the process has been successful, when rebooting it will display a text saying that the list of application is being updated.
--------------------------------------------------------------------------------------------
Edit:
As neileverett suggested, the external memory sdcard could be recognized as sdcard0 instead of sdcard1.
To determine how the sdcard is named by the system, I recommend to use a browser as ES File Explorer or Astro Manager to write down all the content of the external memory and compare this list to the result of the ls command from Step Three.
--------------------------------------------------------------------------------------------
FAQ
Q: My device never connect in adb.
A: First verify that adb drivers are installed.
In my case when I connect the phone, it first emulates a CD player device with a folder containing the generic drivers.
I have to safely remove this emulated CD first (right click on the System Tray icon -> remove device) before the phone accepts to connect itself with MTP or ADB.
Q: I do not have a sdcard.
A: You can try to do the process with internal memory.
First, you will need to navigate the memory with adb shell to find Internal memory
Code:
adb shell
Code:
shell#ls /storage/
shell#ls /mnt/
...
Some examples of the possible location of the internal memory
Code:
/storage/emulated/
/storage/sdcard0
/mnt/shell/emulated/0/
etc.
Sometimes, you get a menu like this prior the actual content of the sdcard0 (internal memory)
Code:
/0/
/legacy/
/obb/
After entering in /0/ or in /legacy/ you should get the actual content of the memory.- Then push update.zip to internal memory
Code:
adb push update.zip $INTERNAL_MEMORY_LOCATION
- In Step FIVE, while in the second menu, choose choose zip from /sdcard by directly pressing Power
From a system point of view, it can open /storage/emulated/ or /mnt/shell/emulated/ that means the folder opened will not be the Internal Memory but a parent folder.
I recommend that you try every possibility by:
- First considering that pressing choose zip from /sdcard led you to the actual Internal Memory content and you shall proceed as normally by looking for update.zip in the current folder.
If it did not work:
- Consider that a parent folder is displayed and the actual memory is in the first sub folder
- Press Power to enter the first sub folder (which may be the Internal Memory) and try to install update.zip- Consider that a parent folder is displayed and the actual memory is in the second sub folder
- Press Volume Down then Power to enter the second sub folder (which may be the Internal Memory)- ...
After each try, reboot and look for the pop-up saying that the list of application is being updated.
You can go on with up to 2 levels of sub folders.
Q: I tried everything, it still do not work.
A: If you have a lot of folders and files in the Memory, the list of content on the CWM recovery will be displayed on several pages.
Make a backup of the Memory, then empty it and add only the update.zip file.
Restart then from Step One.
It should be easier to find the update.zip file.
Q: I own a different Alcatel model, could this trick work with my device?
A: First you can try the other CWM Recovery image Deckter has developed: cwm_alcatel_6036y_v2.7z
To verify that the recovery is correctly booting on the device, when the white screen stabilizes, try to press Power twice.
If the recovery is working, it will enter in the first menu (reboot system now) then confirm the reboot.
In case, after this manipulation, the phone does not reboot, it means the recovery is not working for your device.
(Credits @Decker.Kaluga)
(Credits @morgs640)
(Credits @ModernWorld)
I have just successfully used this method to root my Pop S3 - thanks for the method!
One thing to note:
I found that the method didn't work initially, then with some digging realised that my sdcard was mounted as sdcard0 rather than sdcard 1. It turns out this is because I had changed the default install location under settings - storage to 'external sd card' rather than the default of 'phone storage'.
I temporarily changed this setting back to 'phone storage', and then your process worked first time! Might be worth adding this info to the post?
Thanks once again!
OMG !
So it works with the last update available ?
Possible to have a viewable recovery in the future ?
Draky50110 said:
OMG !
So it works with the last update available ?
Click to expand...
Click to collapse
This should work with any update
Draky50110 said:
Possible to have a viewable recovery in the future ?
Click to expand...
Click to collapse
Decker is willing to develop a CWM for Alcatel Pop S3 but does not possess the device. You can support it on his website. You'll find a link in the description of the Tuto.
Thanks
first thank you for the help. but my visit is to ask permission to make a video tutorial and so Decker.Kaluga to advertise can buy the pops3 and thus make the cwm for it.
negurras said:
first thank you for the help. but my visit is to ask permission to make a video tutorial and so Decker.Kaluga to advertise can buy the pops3 and thus make the cwm for it.
Click to expand...
Click to collapse
Of course, feel free to post the link.
I need help.
When I enter into the custom recovery, it displays a menu. First choose a language. Then a selection. It says:
Reboot system now
Apply update from ADB
Apply update from sdcard
wipe data/factory reset
wipe cache partition
Chose apply update from sd card, it only shows ../
I have a Alcatel pop s3. Please I really need help.
Did you put the update.zip into your SD card ?
DanIgnes said:
When I enter into the custom recovery, it displays a menu. First choose a language. Then a selection. It says:
Reboot system now
Apply update from ADB
Apply update from sdcard
wipe data/factory reset
wipe cache partition
Chose apply update from sd card, it only shows ../
I have a Alcatel pop s3. Please I really need help.
Click to expand...
Click to collapse
It's because you entered in the Alcatel Recovery mode not in Fastboot mode.
From Alcatel Recovery you can only install application signed by Alcatel.
Fastboot mode displays the Alcatel Pop s3 white logo on a black background (this is the first logo that appears when booting normally). Fastboot doesn't display anything else.
To enter Alactel Recovery it's: Power + Volume Up
To enter Fastboot it's: Power + Volume Down
You can also enter in Fastboot by entering the following while still in adb at the end of Step Three:
Code:
adb reboot fastboot
Once in Fastboot, go on with Step Four and so on.
Thanks for this
Any methods in sim unlocking? costum ROMs?
working recovery for 5050x
Hi! I ported recovery for 5050x. screen is work, you can install zip and backup you partitions.
1. extract
2. cmd to folder recovery
3. shutdown phone
4. press Power + vol- on phone it vibrate and connect phone to PC
5. type to run recovery
fastboot -i 0x1bbb boot recovery.img
or to flash recovery
fastboot -i 0x1bbb flash recovery recovery.img
i can't go in fastboot mode
I can not seem to come into fastboot mode POWER + Vol- and with code
Can somebody please make a video tutorial of this? I would love to root my One Touch Pop Icon.
Thank you good job
TWRP 2.6.3.0
amraouifathi said:
Thank you good job
Click to expand...
Click to collapse
You welcome
I ported TWRP 2.6.3.0, but I have not checked thoroughly.
Before backup you mast mount /system /custpack in Mount menu or you cant see backups in Restore menu.
All work good just the fast start don't work please upload the stock recovery
Stock recovery
amraouifathi said:
All work good just the fast start don't work please upload the stock recovery
Click to expand...
Click to collapse
Stock_recovery
Oh thank you i try now lol you are very fast
update TWRP 2.6.3.0
TWRP 2.6.3.0
+system and custpack backup and wipe like one partition
+you can backup persist и firmware
The stock work now i test the twrp