[Q] Please Help me about dopod 818 pro - JAMin, XDA Neo, S200 Software Upgrading

Hello .... I want to ask .... on dopod 818 pro ... why when the upgrade to W6 ... after success, with problems on the charger? when would I have to turn off the charger first, once the indicator lights, new in its turn dopod ... and his battrey be full later, if not in power off or after a restart on the charger battrey will not be full, but information on the LCD in the charger in progress, why? and one again after the windows6 ... when battrey below 10% replacement indicator red light signal is not lit, just a warning only, please help before his enlightenment ... I say thank you a lot.

Related

downgrade problem

hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
i have exact the same proplem now
i have exact the same proplem now
Same Problem
Remove the battery - whait about 3 min. - plug ac power cable without your battery - put the battery - when the orange light on, turn on your device.
back to the life, but not solve the problem.
sorry my english, i´m from brazil. (don´t speak english)
sarpsuerdas said:
hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
Click to expand...
Click to collapse
Sounds to me that you tried to flash a Wizard-ROM on a Prophet.
This is simply impossible, so you probably bricked your device.
well its somewhat working i'm on a prophet bootloader ipl 2.09 spl 2.20 right now and i'm using a crossbow rom from the wizard section right now... (camera is not working).
what you could try is cut the charger wire open and attach the inner cable to the first battery pin (physical top) and the outer wire to the fifth pin. then go into bootloader, connect to computer and flash a prophet rom which has spl and ipl included.
dou you have a g3 or g4 device? on which spl/ipl are you right now...
I did the same thing with my s200.
I remove cable and battery, insert adapter cable and then battery until I get a steady amber light (usually takes 2-4 attempts).
When it boots up I quickly replace the adapter cable with the computer cable and Active Sync works.
I would like to reflash it but I can't since my battery is reporting 0% always, even when the battery is fully charged and it's not charging either. (And I can't get into the bootloader either.)
@crOssy: are the batteries different between models? and if so, would your proposed wiring actually work? have it been tested?

M3000 won't start after flashing Faria WM6

Hey guys ..
i just installeerd Faria WM6 rom on my SPV M3000, and after the reboot (when it was finised) it came back and just went black.
I cant start the dham thing any more. The battery led isnt up also when attached to the powercord.
Any help please!!
this ROMs are designed for the Wizard. I dont know if you device is like the wizard. But it look like a brick... time to spend 30 bucs to buy a wizz
the M3000 IS a wizard... tell me exactly what happened Mr Richz...
Try taking the battery out for a couple minutes, and the putting it back in, and hit the power button and tell me if the LED light comes on ...
My M3000 is CID locked and try to flash it with ShellTool.
I did it yesterday with the Wizard_Love ROM and that worked fine.
But when i was flashing the Faria Rom it was completed, restarted and then nothing happend any more. totally black and wont come back to life..
i tryed it with the wall charger and the USB charger but no results, also removed the battery. But the Battery LED wont come on.
my ipl/spl was 2.18.001

QTEK S200 completely dead after upgrade

Hi All,
After installing Prophet_G3_G4_RadioRom_v2.69.21.exe onto my QTEK S200 it's completely dead. I cannot start it up anymore, even with the battery connected to power. The orange charging light doesn't even go on. I don't get anything here, no QTEK screen, no boot, no nothing even after pressing the button for several seconds.
Anybody knows what happened? Is my battery dead? When I connect the QTEK to the power supply without the battery inserted, the light flashes red for a short second and then... nothing... The battery was almost fully charged when I started the upgrade. IPL was at 2.20.
euh... help!!!
I guess you are having hardware problems, otherwise you would see a error screen... like the stuck qtek splash screen or the bootloader
coolb4all said:
Hi All,
After installing Prophet_G3_G4_RadioRom_v2.69.21.exe onto my QTEK S200 it's completely dead. I cannot start it up anymore, even with the battery connected to power. The orange charging light doesn't even go on. I don't get anything here, no QTEK screen, no boot, no nothing even after pressing the button for several seconds.
Anybody knows what happened? Is my battery dead? When I connect the QTEK to the power supply without the battery inserted, the light flashes red for a short second and then... nothing... The battery was almost fully charged when I started the upgrade. IPL was at 2.20.
euh... help!!!
Click to expand...
Click to collapse
Can you read spanish?
http://www.todopdas.es/forumdisplay.php?f=23
quiet, thast has solution
I have the same problem
any solution for this problem? the device is completely dead!!
remove you battery and charge it at an external power suply (universal charger for example) and then put it back and see if there is any result.

Did wm 6.1 kill my wizard???????????

hellow to all . i resently installed wm 6.1 on my wizard and eventualy the battery ran out ,so i connected the charger and to my suprise it did not charge so i tryed with another charger and the same result. the thing is it was working perfictly with wm 5.0 and ever since wm 6.1 this happend.to do the install i used awizard to do the ulocking bouth sim and cid then i down graded the IPL and then flashed the PTG rom and it worked perfectly intil the battery situation.when i plug the charger the red light turns on but thats all it does , and it stays that way for days in a row . ive tryed two diffrent battries. can any one help or give any ideas on this situation, thanks in advance.
Most likely you have flashed a G3 IPL and SPL to a G4 device. If it is the case, then sorry that you've got a brick.
the device is a g3 and ipl spl is g3 the olny thing im not sure about is the rom,here is the link from where i got it.http://forum.xda-developers.com/showthread...d=1#post2601705 , can any body tell me if g3 or g4 rom...thanks
please post the full link, its not complete..it gives a 404 Error
There is no G4-only ROM, all custom ROMs now are G3 and G4 capable.
Try to press the reset hole and see if it goes to RUU or not. If it still doesn't power off even though the charge light became green, then there may be a hardware error.
the problem you are experiencing imay be the amp on your charger.
Only an HTC wall charger can revive a flat dead battery.
This charger should say that it is 1Amp (1000ma)
If you use a charger from a motorola/blackeberry/USB charger it will not help you in this case.
Check your amp.
If you do not have an official wall charger, then the only way to revive is to get a new battery
yes i agree with SVI, because i myself faced this probm, when i got a new batt..i had to charge it fully firstt :/ but i went on with the upgrades..and the batt died on me..i used a motorola v3 charger but didnt work..then i went to the shop owner to replace it..and he said that there is a special chargers for these HTC phones, i bought that and its working perfectly now
hey guys thanks for the replies and ive tryed all those solutions ,the wall charger from my htc trinity and the wall charger from the qtek wizard it self and neather do anything.
the only thing that dose work is putting the battery from my trinity and holding it with my hand in place. it turns on but it dosent stay on for long .
it turns off in the following maner the screen starts going white and it stays that way.
i tryed going to bootloader mode and i succeaded but then it turned to the white screen.
changing the subject the IPL is 1.01 and the SPL is 2.18 the rom is a 6.1 ptg rom here is the link:http://forum.xda-developers.com/showthread.php?p=2601705&posted=1#post2601705 this link works i tested it. can anybody tell me if this rom is for g3 or g4 devices, the device with wm5 works fine . or can it be from the IPL and SPL not being the same. can any one tell me why this is happaning iv flashed so many devices and never had this problem . i my self have a qtek magicion, a htc trinity and a qtek prophet. well hope for some help thanks again.
Yes, first step is to ensure that you have a fully charged battery, a new battery is not fully charged so a desktop charger will be helpfull.
The IPL SPL difference is discussed by Dr Puttingham post
http://forum.xda-developers.com/showthread.php?t=285435 step 16
"Watch the rebooting of your PDA, if BOTH IPL and SPL are 1.xx then great. Quite probably your IPL will be 1.xx and your SPL will be 2.xx. Rerun the button 1.05 ROM downgrade a second time and it will become 1.x on both IPL and SPL. You don't need to redo the unlocking."
Hopefully you can maintain bootload (press and hold camera button on start-up) with the new battery
Anouther hopefully usefull post is
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck
ademim said:
hellow to all . i resently installed wm 6.1 on my wizard and eventualy the battery ran out ,so i connected the charger and to my suprise it did not charge so i tryed with another charger and the same result. the thing is it was working perfictly with wm 5.0 and ever since wm 6.1 this happend.to do the install i used awizard to do the ulocking bouth sim and cid then i down graded the IPL and then flashed the PTG rom and it worked perfectly intil the battery situation.when i plug the charger the red light turns on but thats all it does , and it stays that way for days in a row . ive tryed two diffrent battries. can any one help or give any ideas on this situation, thanks in advance.
Click to expand...
Click to collapse
Its sounds like a battery drain partial brick. Under normal situations, the phone will shut down before the battery is completely drained. This is so you don't end up with a completely dead battery. Sometimes, like when the phone is frozen or at the bootloader screen it will run itself completely dead. It sounds to me like you have a completely dead battery. To charge under normal conditions, your battery has to have enough juice to boot the phone one more time. See, when you plug your phone in, if its not on, it will turn on. During boot, there is no connection between charger and battery...the battery has to have enough juice to make it through boot at which point the phone enables the charger. The way I fixed my battery brick was by cutting the end off of a usb cable, striping the wires, and jumping a charge onto the battery.
Please refer to this blog for a description of the steps involved in this process:
http://www.asktheadmin.com/2007/06/htc-wizardcingular-8125-dead-battery_21.html
could be as stupid as the ongoing connection initiated by activesync:
check the schedule settings and change it to manually.
http://forums.wireless.att.com/cng/board/message?board.id=samsung&message.id=62948

[Q] [q] htc s710 big charging problem please help me !!!

When connecting the phone to the charger the LED light blinks orange
and does not charge the battery (normal the LED should stay lit orange constantly).
I tried another charger ... same problem,I tried even with data cable ... same result .
I changed the ROM (6, 6.1, 6.2, 6.3, 6.5)
Even reset the phone .... nothing seems to work.
Does anyone know what the problem is.
Please help me. Thanks !!!

Categories

Resources