Database Info

downgrade problem

hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..

i have exact the same proplem now
i have exact the same proplem now

Same Problem
Remove the battery - whait about 3 min. - plug ac power cable without your battery - put the battery - when the orange light on, turn on your device.
back to the life, but not solve the problem.
sorry my english, i´m from brazil. (don´t speak english)

sarpsuerdas said:
hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
Click to expand...
Click to collapse
Sounds to me that you tried to flash a Wizard-ROM on a Prophet.
This is simply impossible, so you probably bricked your device.

well its somewhat working i'm on a prophet bootloader ipl 2.09 spl 2.20 right now and i'm using a crossbow rom from the wizard section right now... (camera is not working).
what you could try is cut the charger wire open and attach the inner cable to the first battery pin (physical top) and the outer wire to the fifth pin. then go into bootloader, connect to computer and flash a prophet rom which has spl and ipl included.
dou you have a g3 or g4 device? on which spl/ipl are you right now...

I did the same thing with my s200.
I remove cable and battery, insert adapter cable and then battery until I get a steady amber light (usually takes 2-4 attempts).
When it boots up I quickly replace the adapter cable with the computer cable and Active Sync works.
I would like to reflash it but I can't since my battery is reporting 0% always, even when the battery is fully charged and it's not charging either. (And I can't get into the bootloader either.)
@crOssy: are the batteries different between models? and if so, would your proposed wiring actually work? have it been tested?

Qtek s200 dead? No charging etc.

Recently screen of my qtek started to act werid. It was dark like only a half of the pixels flashed. I thought that it is a software problem because up to that moment phone worked just fine so I tried to flash it with a new rom... and I failed... about three times... now my phone is dead and i can't even charge it - no reaction (not even a light). What should I do (burry my best friend?) ? Can anyone help ?

If you cannot charge it you wont be able to flash it again since it is not allowed under 50% of the charge. I advice you to insert a charged battery. Got any friend with a prophet? then reflash it again, doing the whole procedure described in some other posts like:
http://forum.xda-developers.com/showthread.php?t=283245&page=2
you can find some roms there too

M600/Prophet dead to the world!

Hi all, I need a little help!
Got an Orange SPV M600 - Had old rom - Upgraded to WM6 rom, all worked sweet. Tried to do a CID unlock using awizard1.2 (Left it alone for a while to do its thing) not i cant get it to turn on at all.
1. Tried a master reset - Camera + Comm Mgr + soft reset (Nothing happens)
1a. Tried Camera and softreset too (nothing happens)
2. Tried Charger short to Pins 1 and 5 (nothing happens)
3. Left battery out for 24 hours (Nothing happens)
I have bricked the device! - Is there anything else I can do except go back to orange or htc service dept and ask for help?
Cheers

Hi!! Where did you get the WM6 rom for SPV M600??
Have been looking for ages!!

killian1407
Go to Tonydeli7 thread on upgrading. Go & flash the WM5 NVID version.
Then download your choice of WM6 version from PDAviet.
Dogs Nads mate. I unlocked my £75 eBay SPV M600 (courtesy of the gang) to use on Vodafone company chip, but the stock crappy grey background on the Orange WM5 fone dialer skin is total toilet..Just cant been seen on windscreen mount in my car. Follow the rules written by the guys (actually went a lot quicker than the 15-20 ,mins)..JOB DONE!
..PROPR BO I TELL THEE!!

M600 Still dead!
I have been waiting an age for someone to reply to my post with a solution but non has turned up.
Still have the problem but now its gotten a whole lot worse.
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
2. Have chopped a charged and tried the pin 1 white and pin 5 other cables method but I still get no response. I have tried all combos of stylus and buttons but I just cant make this device respond.
I have just about given up hope of ever resurrecting this thing!
Is there anything else I could try?
Thanks.

i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo

laser-interceptor said:
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
Click to expand...
Click to collapse
As you started a new thread, I posted my reply overthere.

lot of people with same problem.
hi, lot of people (and me ) got the same problem after flashing on wm6.
Look on the g4 topic under "prophet upgrading", i think you've got the same problem like me and other.
After opening my phone, i think this is a capa out :/

dvdfilmbuff said:
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
Click to expand...
Click to collapse
i quest that this 10sec its charge internal batt ... i got same trouble with my prophet

Recover HTC Touch Cruise

Hi!
I have a HTC touch Cruise for about one month now. Starting with last week it started to say that the "main battery is low, device will close" even if the battery is charged (even pluged in). I tried soft reset, battery out, hard reset, nothing. So I decided to reflash it. Now, it gets to the Windows start up screen but after I can hear the sound for turning off device, and the phone turns off for no reason and without a message.
The original language was french, and it was flashed with a english version and olipro spl.
Does anyone has a idea how I can recover my phone ? I have tried to load several roms, none of them worked.
Please help,
Thanks

I have the same 'Main battery is very low' problem on my TC, even when the battery is almost full. I have this issue on Bepe's ROM, ASerg's ROM and also on the official HTC WWE ROM.
It occurs frequently when I soft-reset. When it happens, I can only succesfully start my phone after completely charging it (LED turns green).
I think it must be a hardware problem in my TC. Switching the battery with another TC-battery did not fix it.
Can't you use your phone at all?

Seems like I got the same problem as you guys http://forum.xda-developers.com/showthread.php?t=402765
Any solution yet?
Is it the same on your side, that when you boot up with the Charger plugged in you don't get past the first splash?

No more bootloader no more nothing, after rom upgrade s200

Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks

If the accu not charge, I think he is dead. You need a new one. For flashing new rom, you need a good acco over 50 %. Than you go to bootloader modus and flash a WM5 Rom WM5Rom.

coolb4all said:
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
Click to expand...
Click to collapse
Yep, hes dead alrite, make a good paper weight sorry bro...

not the battery
of course I tried a new battery
same problem

Can you make a downgrade to WM5 ? Ist the battery charged now ?

DC Adapter 4,5 V
I had the same problem.
Remove the battery and connect the pin nr 1 (nearest to the cam) to + and the pin nr 5 to -. I think 3,7 to 5 V is ok. Then bootloader and connect to computer.
Don't blame me if anything goes bad ;-)

how to proceed?
I've tried to do as explained...
I've taken an old charger (5v) and connected the cables (black/white striped to 1 and black to 5). I'm not 100 percent sure about + and -, but normally black is always -, if I'm not mistakin'
What should happen? How should I proceed?
My device does nothing... No light. Power button does nothing, hard reset does nothing.
Does this procedure work with a QTEK S200?
Maybe the charger (old gsm) is too old or broken?
Maybe + is black...
Sooo many options ;-)

Worked on mine S200
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?

JustBored said:
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
Click to expand...
Click to collapse
I Did the same thing '''''HELP"""

What you should do
Keep the device on for 2 hours connect it to the electricity.
Install the original rom with the PDA connected like that to the PC, if it does not enter the Rom update continue trying by doing a hard reset with the stylus and pressing the left com button on the left side of the device, then retry the rom install, if it says unable to connect continue trying, using the procedure i explained before, thats what i did when the same stuff happen to me i was without my device working for a month, now i´m using WM6 with the Diamond Rom, so its possible, to do this you just have to keep trying.

my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?

srbwap said:
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
Click to expand...
Click to collapse
My friend. A few people have tried the pin method and one or two have succeeded. IMHO i would not try it, for fear of frying your phone, yourself or starting a fire.
Take out the battery for a good couple of hours. Take out SIm card and SD card. Put battery back in and try to charge for at least 5 hours, even if the light does not show (might just be LED issue).
Then see if you can start in boot loader, u now how to yes? (keep camera button pressed, soft reset with stylus, then let go of camera button after few sconds). What happens?

pins to power
I've tried connecting the extreme small pins to the (big) cables of the charger but nothing happens over here. The screen stays black.
To All,
Any hints on how to connect these cables to the pins, without the fact that they're constantly coming off the pins and constantly touching other pins?
You try and tell me about your experience ;-)

revive prophet revive ;-)
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))

coolb4all said:
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
Click to expand...
Click to collapse
keep it plugged in for about 5 hours, dont play with it or turn it on lol, give a go unless u have done already and just havent said

Direct Connection to 220v doesn't work
The workaround of connecting the pins directly to the charger doesn't seem to work on a QTEK S200 G4.
Since mine is a G4, I wasn't lucky... I'm left with a cut charger cable.
I'll try to charge it for 5 hours but since no led is going on I don't think this will have any effect.

Listen keep it plug in to the electricity for 12 hours, then try to put it in bootloader mode by pressing the, com button on the left side of the device after you hard reset it, with the stylus after you manage to enter the bootloader mode, you only need to follow the steps described on several posts on the forum.

if nothing works connect the device and try to install the original rom, my device is a g3 so i´m not sure if the g4 works the same way.