Database Info

downgrade problem

hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..

i have exact the same proplem now
i have exact the same proplem now

Same Problem
Remove the battery - whait about 3 min. - plug ac power cable without your battery - put the battery - when the orange light on, turn on your device.
back to the life, but not solve the problem.
sorry my english, i´m from brazil. (don´t speak english)

sarpsuerdas said:
hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
Click to expand...
Click to collapse
Sounds to me that you tried to flash a Wizard-ROM on a Prophet.
This is simply impossible, so you probably bricked your device.

well its somewhat working i'm on a prophet bootloader ipl 2.09 spl 2.20 right now and i'm using a crossbow rom from the wizard section right now... (camera is not working).
what you could try is cut the charger wire open and attach the inner cable to the first battery pin (physical top) and the outer wire to the fifth pin. then go into bootloader, connect to computer and flash a prophet rom which has spl and ipl included.
dou you have a g3 or g4 device? on which spl/ipl are you right now...

I did the same thing with my s200.
I remove cable and battery, insert adapter cable and then battery until I get a steady amber light (usually takes 2-4 attempts).
When it boots up I quickly replace the adapter cable with the computer cable and Active Sync works.
I would like to reflash it but I can't since my battery is reporting 0% always, even when the battery is fully charged and it's not charging either. (And I can't get into the bootloader either.)
@crOssy: are the batteries different between models? and if so, would your proposed wiring actually work? have it been tested?

HELP!!!Impossible to charge the battery,permanent RED Led

As i said on the title,suddenly i couldn't recharge my Universal anymore,yes i've tried with a brend new official battery as well but everything was in vain.As soon as i plug my charge to my Universal it appear a Red Led and after 3 min or so the led turn off and so the battery.
How can i fix this problem?!
Is there any chance?!
Is it really dead like that?!
Please HHHHHHHEEEEEEEEELLLLLLLPPPPPPPPPPPPPPPPPPP!!!!!!!!!!!!!!!!

If the battery is really brand new, then I guess the connectors might be damaged or the internal power buses might be broken somewhere. Have you dropped your device recently? Or did anything that might explain broken connectors or internal buses?

Nothing happened to my device and never felt down,it just happened suddenly!Now if i won't be able to fix this by myself this means a finger in da a.. cuz my warranty is expired!DAAAAAAAAMN

tetsuokaneda said:
Nothing happened to my device and never felt down,it just happened suddenly!Now if i won't be able to fix this by myself this means a finger in da a.. cuz my warranty is expired!DAAAAAAAAMN
Click to expand...
Click to collapse
It can be a software error. Have you tried hard resetting or installing another ROM?

tnyynt said:
It can be a software error. Have you tried hard resetting or installing another ROM?
Click to expand...
Click to collapse
That's the point!!!
I was trying to update to WM6 but something went wrong and stucked in boot load screen!Then my battery died but when i've tried to charged again i had that problem!!!

tetsuokaneda said:
That's the point!!!
I was trying to update to WM6 but something went wrong and stucked in boot load screen!Then my battery died but when i've tried to charged again i had that problem!!!
Click to expand...
Click to collapse
Your battery is fine, unfortunately your device broke

Unless you have a lot of specialized equipment at home, and the proper qualifications, there's no way in hell you can fix this. I'm sticking with my diagnosis, that either the power routing circuit broke down, or a power bus inside the device.
Really, your best off taking it back to the store, and paying for the repair. Either that, or buying a new phone, and selling this one for spares...
Sorry mate...

mzalan said:
Unless you have a lot of specialized equipment at home, and the proper qualifications, there's no way in hell you can fix this. I'm sticking with my diagnosis, that either the power routing circuit broke down, or a power bus inside the device.
Really, your best off taking it back to the store, and paying for the repair. Either that, or buying a new phone, and selling this one for spares...
Sorry mate...
Click to expand...
Click to collapse
I wanna die!!!I'm completely Fu.. up!!!
What a terrible news!I can't believe it!!!!
If i'll bring my phone to the assistant i'm gonna pay alot of money,at least 200.00 euro!!!!

similar problem
i had the exact same thing happen to my EXEC when i got 2 new batteries for it. One was a standard sized, pretty much the same as the stock one that came with the phone and one was a much larger capacity one that needs an extra cover for the back.
Id been using the device for ages on this huge battery and the charge said 100% constantly. then the device turned itself off and it wouldnt come back on. upon connecting the charger the LED was red, so i thought the battery was dead. I left it on charge over night and when i tried again the next morning it was fine.
this happens everytime with this battery, it just needs a much longer charge than the standard one, and doesnt register properly on the default OS, i havent tried it on my recent upgrade to one of the midget roms.
so try leaving it on charge over night or for a very long time. if all else fails just get a new battery.

That might reset the battery back to life, but I wouldn't exactly count on that. A battery with a broken monitor circuitry is pretty hard to reset.

My last hope,i'm gonna leave charging my phone for a day and then see what happend....I'm desperate

Permanent red light...
I had this problem, I put the phone on charge but forgot to put a battery in - spare phone... It wouldn't work no matter what I did , until I reformatted the DOC by following the steps in the WIKI.

wtpelzer said:
I had this problem, I put the phone on charge but forgot to put a battery in - spare phone... It wouldn't work no matter what I did , until I reformatted the DOC by following the steps in the WIKI.
Click to expand...
Click to collapse
Could u post it please?!

Took a while but here it is...
I did the task 28 55aa command in MTTY which should reformat the DOC alternatively you could reload the bootloader using the link below...
MTTY with "task 28 55aa", "set 14 0", "set 14 9, "set 14 10" and "set 14 20" as described. bootloader screen may be replaced with a blank one, boot it on bootloader mode by "Backlight+Power+Reset"
http://wiki.xda-developers.com/index.php?pagename=Universal_Resets
now upgrade as usual.
If you stuck on the bootloader again after upgrading, try to upgrade the bootloader itself go to http://forum.xda-developers.com/showpost.php?p=1255206&postcount=52
This link gives full instructions :
http://forum.xda-developers.com/showthread.php?t=289325&highlight=task+28+55aa
Hope this helps.

Same Problem, Led Indicator Always red
Hi,
We have the same situation, my jasjar just died in my hands, im reading a txt messages then al of the sudden it hangs, so what i did is reset it but it didnt power on, i removed the battery then after 10mins i put it back but then no power,then i charged it but it didnt power on too and the led indicator is always red, they say that if the indicator is red it means that there is no battery or the battery is missing but i check it thoroughly,the battery is perfectly place on the back of jasjer, i even tried to enter to bootloader but it cant. If anyone knows how can i revive my jasjar pls pls let us know....Thank you so much.
So sad till now there's no single solution.....

wtpelzer said:
I did the task 28 55aa command in MTTY which should reformat the DOC alternatively you could reload the bootloader using the link below...
MTTY with "task 28 55aa", "set 14 0", "set 14 9, "set 14 10" and "set 14 20" as described. bootloader screen may be replaced with a blank one, boot it on bootloader mode by "Backlight+Power+Reset"
http://wiki.xda-developers.com/index.php?pagename=Universal_Resets
now upgrade as usual.
If you stuck on the bootloader again after upgrading, try to upgrade the bootloader itself go to http://forum.xda-developers.com/showpost.php?p=1255206&postcount=52
This link gives full instructions :
http://forum.xda-developers.com/showthread.php?t=289325&highlight=task+28+55aa
Hope this helps.
Click to expand...
Click to collapse
Exactly if my Jasjar is completely dead how can i connect via usb and then use mtty?!
I'm losing my hope to bring it back to live!

have same problem - can do nothing, still waiting
but there is one thing - led flashes once, when i put the charger into the device - but it does nor light, nor flashes - exactly nothing happens

If your device is dead...
Well just to answer the question, if the battery is dead and you can't charge it because of a red LED. I suggest you buy a standalone charger from ebay and charge the battery or get someone else to charge it for you. Then follow the steps as I stated in my previous post...

wtpelzer said:
Well just to answer the question, if the battery is dead and you can't charge it because of a red LED. I suggest you buy a standalone charger from ebay and charge the battery or get someone else to charge it for you. Then follow the steps as I stated in my previous post...
Click to expand...
Click to collapse
The point is that the device is dead and that is why the constant red light. I have a device that is stuck on the splash screen (no solution in sight) and another that fell down and broke. The one that fell down does not power on. If you put a charged battery ang plug in the charger nothing happens, no light comes on, but if you put a discharged battery the red light comes on. I have a third Uni that I accidentally flashed with a BA rom. It is behaving exactly like the broken uni, it does not turn on, does not go into bootloader and the red light comes on when I plug in the charger with a discharged battery in it.

For some things, there's just no cure...
Okay I understand where you're coming from but essentially what you need to do, under normal circumstances, is connect it to your PC, which if the device is working at all the PC will detect it but not connect... In the case of two of your Uni's I don't think this will help - the dropped one and the BA ROM failure. The one with the Red LED, which has stopped working could be a component failure on the board or it could be a Corrupt DOC table. Now to get back to how you'd go about fixing it if it is a corrupt DOC table, when you connect it to the PC and the PC detects it you disable ActiveSync and start MTTY it should give you the option of connecting to the USB port, when it does this if you get a prompt the problem should be fixable because MTTY can "talk" to the device... As for the other's try this method and if it doesn't work sell them for parts or canabalise the one for parts for the other...

Help! Noobie - can't get it to turn on!!!

I can't even turn my Newish XDA Exec on!!!
I received it this morning and I just get the 02 flash screen to come on for a couple of seconds then it goes blank... it's doing this over and over.
The charging light comes on for a bit too (was ok for awhile - staying on all the time) now it goes amber then red while the splash screen comes on then everthing goes dark!
Pleeeease don't say it's broke
I've tried charging with the charger but the light is red so it's now plugged into my pc and going on and off...
I forgot to bring the CD with me - is that needed at this stage? ie: just turning the thing on? is there a site that I can download the software from rather than use the CD?
*sob* gonna cry soon...
it has small letters in the top left screen R G D with numbers next to them (what does that mean?)
Would really appreciate some help and advice please.
Thank you
(Happy New Year )

Welcome to the forum.
First don't cry
Second, check if the battery is connected tightly and correctly.
Then turn it off and connect it to a wall charger (not PC) and let it charge for at least 6 hours (unless there is a red light).
If there is still a red instead of orange charging light this means the battery is bad.
Since it is new it should still be under warranty.
As for the disk there you do not need it. To transfer files and synchronize outlook info to your PC you need MS ActiveSync which is free and available on MS site.

Hi
I've not started crying as yet but on a slippery slope to a good sulking!
Is it suppose to be flashing red? (I don't think it's amber!!) (do you think if I went into a shop and got them to test a battery to see if it works with a new one - but I wouldn't buy it from them - cheaper to buy online)
I would have thought I'd get something as it's been charging now for about 3 hours (on and off - I've been trying the usb cable every now and then which is when I get the flash screen to come up for a few secs - don't get anything when it's in the normal charger).
(I've brought this 2nd hand so no warranty! my mobile phone, which this XDA is suppose to be replacing is new but o2 said they wont fix it and it's only 7 months old!!)
thanks for your help

It's working!!
I did think that the flashing red colour was wrong.. was told it was suppose to be a solid colour.
Phew.. I was getting very worried!
it might need a new battery at some point - but at least I know it works
Thanks for your help

No more bootloader no more nothing, after rom upgrade s200

Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks

If the accu not charge, I think he is dead. You need a new one. For flashing new rom, you need a good acco over 50 %. Than you go to bootloader modus and flash a WM5 Rom WM5Rom.

coolb4all said:
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
Click to expand...
Click to collapse
Yep, hes dead alrite, make a good paper weight sorry bro...

not the battery
of course I tried a new battery
same problem

Can you make a downgrade to WM5 ? Ist the battery charged now ?

DC Adapter 4,5 V
I had the same problem.
Remove the battery and connect the pin nr 1 (nearest to the cam) to + and the pin nr 5 to -. I think 3,7 to 5 V is ok. Then bootloader and connect to computer.
Don't blame me if anything goes bad ;-)

how to proceed?
I've tried to do as explained...
I've taken an old charger (5v) and connected the cables (black/white striped to 1 and black to 5). I'm not 100 percent sure about + and -, but normally black is always -, if I'm not mistakin'
What should happen? How should I proceed?
My device does nothing... No light. Power button does nothing, hard reset does nothing.
Does this procedure work with a QTEK S200?
Maybe the charger (old gsm) is too old or broken?
Maybe + is black...
Sooo many options ;-)

Worked on mine S200
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?

JustBored said:
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
Click to expand...
Click to collapse
I Did the same thing '''''HELP"""

What you should do
Keep the device on for 2 hours connect it to the electricity.
Install the original rom with the PDA connected like that to the PC, if it does not enter the Rom update continue trying by doing a hard reset with the stylus and pressing the left com button on the left side of the device, then retry the rom install, if it says unable to connect continue trying, using the procedure i explained before, thats what i did when the same stuff happen to me i was without my device working for a month, now i´m using WM6 with the Diamond Rom, so its possible, to do this you just have to keep trying.

my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?

srbwap said:
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
Click to expand...
Click to collapse
My friend. A few people have tried the pin method and one or two have succeeded. IMHO i would not try it, for fear of frying your phone, yourself or starting a fire.
Take out the battery for a good couple of hours. Take out SIm card and SD card. Put battery back in and try to charge for at least 5 hours, even if the light does not show (might just be LED issue).
Then see if you can start in boot loader, u now how to yes? (keep camera button pressed, soft reset with stylus, then let go of camera button after few sconds). What happens?

pins to power
I've tried connecting the extreme small pins to the (big) cables of the charger but nothing happens over here. The screen stays black.
To All,
Any hints on how to connect these cables to the pins, without the fact that they're constantly coming off the pins and constantly touching other pins?
You try and tell me about your experience ;-)

revive prophet revive ;-)
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))

coolb4all said:
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
Click to expand...
Click to collapse
keep it plugged in for about 5 hours, dont play with it or turn it on lol, give a go unless u have done already and just havent said

Direct Connection to 220v doesn't work
The workaround of connecting the pins directly to the charger doesn't seem to work on a QTEK S200 G4.
Since mine is a G4, I wasn't lucky... I'm left with a cut charger cable.
I'll try to charge it for 5 hours but since no led is going on I don't think this will have any effect.

Listen keep it plug in to the electricity for 12 hours, then try to put it in bootloader mode by pressing the, com button on the left side of the device after you hard reset it, with the stylus after you manage to enter the bootloader mode, you only need to follow the steps described on several posts on the forum.

if nothing works connect the device and try to install the original rom, my device is a g3 so i´m not sure if the g4 works the same way.

spv c600 not starting

hello everybody.i have a problem with my spv c600.i bought it few days ago.i had installed some apps on it and next morning my phone was off,althought the battery was full.i made hard reset for three times and the phone started.but this is happening every morning from then.and now i can`t make hard reset.after it asks me to press 0 key shows orange screen and after that turns off.sometimes shows the windows mobile screen but only that and turns off.i don`t understand what is the problem...is it software or hardware problem?
can someone tell me what can i do?i want my phone back...i like it to much
sorry for my bad english

i`m not sure if i posted to the correct section but no one can`t help me?

Try to enter Bootloader (hold camera button and shortly hold Power).
After Bootloader started, you need reflash official ROM.

it enters in bootloader but it stays only 3 seconds and after that turns off.i`m going crazy....i don`t know what to do...is it the battery the problem?but last time when it worked the battery was full
other ideas?

try other battery, or try turn on without battery only power cable plugin.

the same thing without baterry.it stays 3-4 second and after that turns off.which is the problem?
and i don`t understand what is with the led colour.when i put the phone to charger the light is red...i try to make hard reset but the phone turns off and and one cuple of times...the led color becomes orange and green sometimes...
so?what is going on?

can someone help me please?

I think that it is hardware problem. Before am I bought my HTC Tornado, I had Sony Ericsson P900 and after 2 years using suddenly he after power on he stopped at the introductory animation. So I gave it to the service and told me that is it a problem with the motherboard. Your SPV C600 looks that is on it similar.

and what happend with your tornado?

With my Tornado nothing. The hardware problem was in my Sony Ericsson P900. In service told me that is it a problem with the motherboard and that the correction would cost cca 850$ . So I declined correction and bought HTC Tornado, which still works .

oh..thanks anyway.i think i will go to service with my spv...

wow it didn`t started for 2 days and now is working like is new.i don`t understand...where is the problem?

it worked only 2 hours and after that it was dead again

what can i do to fix this problem.it`s ok to change the rom?

fixed.i sold the phone